Chemical composition of T-21 silica tubing and implications for neutron activation analysis

T-21 silica, a commonly used encapsulation material in neutron activation analysis of small samples, was analyzed by INAA to determine trace levels of the following impurities: Na, Sc, Cr, Fe, Co, Ni, Zn, Br, Sb, La, Ce, Sm, Tb, Hf and Au. In the unprocessed form supplied by the manufacturer, pieces of T-21 weighing 50 mg contain 6·10^–2 g Na; 9·10^–3 g Fe; 3·10^–7–7·10^–6 g light REE, Sc and Hf and 4·10^–8 g Tb and Au. In a series of glass-blowing steps, in which unfiltered gases were used for fuel, and cleaning steps, in which reagent grade aqua regia was used, irradiation vials were produced which contain higher average levels of Sc, La, Sm, Tb and Hf, by factors ranging from 1.3 for Sm to 11.5 for La, and lower average levels of Co, Na and Fe, by factors of 1.4, 2.0 and 4.0, respectively, than the unprocessed material. These contamination levels lead to blank corrections of 21% for La, 2.6% for Ce and 3.0% for Hf in 40 g samples of refractory inclusions from carbonaceous chondrites, if counted in their irradiation vials.     

Ceramic glaze analysis by simultaneous in-beam PGAA and XRFS

Twenty-one ready-to-use hobby glazes, of which 18 were labeled safe for food containers (SFFC), were analyzed for Al, B, Ba, Ca, Cd, Co, Cr, Cu, Fe, Gd, Hf, K, Mn, Na, Pb, Si, Sm, Sr, Ti, Zn, and Zr by neutron capture prompt -ray activation analysis (PGAA). Simultaneously, Pb was also determined by X-ray fluorescence spectrometry (XRFS) using Pb K X-rays induced by the -ray component of the neutron beam. The XRFS limits of detection were 200–400 g Pb·g^–1 (dry weight), a factor of 100 better than those for PGAA. Pb concentrations (by dry weight; with weight losses ranging from 28 to 49% after air-drying) found were 0.16–27.2% in the SFFC glazes and 0.86–32% in the other glazes. The SFFC glazes contained from <0.6 to 202 g Cd·g^–1, and Co, Cr, and Cu (elements which may enhance Pb leaching from fired glazes) were found in concentrations up to 1.2, 2.7, and 5.6%, respectively. Method accuracy was demonstrated with the analysis of soil, fly ash, and glass standard reference materials.     

Analysis of the CCRMP reference rocks SY-2, SY-3 and MRG-1 by instrumental neutron activation

Three Canadian reference rocks, syenites SY-2 and SY-3, and gabbro MRG-1 have been analysed for Na, K, Sc, Cr, Fe, Co, Zn, As, Rb, Cs, Ba, La, Ce, Nd, Sm, Eu, Tb, Yb, Lu, Hf, Ta and Th, by instrumental neutron activation analysis. The results are reported and compared with usable values. In general the agreement is good.     

Assessment of the essential element and heavy metal content of edible fish muscle

The aim of this work was to determine the concentrations of some essential and toxic elements in the muscle of ten species of commercial fish consumed in Portugal. We combined two different techniques for determination of the elements—energy-dispersive X-ray fluorescence (EDXRF) was used to quantify K, Ca, Fe, Zn, Se, Rb, and Sr and flame atomic-absorption spectrometry for analysis of Cr, Ni, Cu, Cd, Hg, and Pb. The latter technique was used because of its higher sensitivity, because these elements were not detected by EDXRF. The results obtained show a similar pattern for the trace elements. K and Ca are present at the highest concentrations in all the samples studied, from 0.6–1.3% and from 0.04–0.08%, respectively, followed by Zn, Fe, Sr, Se, and Rb. Sr is present at higher concentrations than Rb in all the species studied except meagre. Concentrations of the elements in octopus do not follow this pattern—Fe is present at a higher concentration than Zn. Low concentrations of Cr (0.66–1.5 g g^–1), Ni (0.11–0.24 g g^–1), Cd (0.01–0.08 g g^–1), Hg (0.49–2.74 g g^–1), and Pb (0.02–0.06 g g^–1) were observed in all the samples analysed. The concentration of Hg was highest in Helicolenus dactylopterus—5.4 g g^–1 in one sample.     

Instrumental neutron activation analysis of blood serum

Instrumental neutron activation analysis has been used to determine 15 trace elements in twelve blood serum samples taken from healthy students at Bilkent University in Ankara. The method allowed the determination of Sc, Cr, Mn, Fe, Co, Zn, Se, Rb, Cs, Ce, Eu, Tb, Hf, Ta and Hg, which occur at the g.ml^–1 to ng.ml^–1 levels. There are no values reported for Tb, Hf, Ce, Eu and Ta before. The other results are compared with the values reported in the literature. Most are in the range of the reported values except for Fe, Zn, Se and Cs.     

Trace characterization of high-purity nickel by instrumental and radiochemical neutron activation analysis

Summary The high activity of the radionuclides ⁶⁵Ni (t_1/2=2.52 h) and ⁵⁸Co (t_1/2=70.8 d) imposes severe limitations on the performance of direct instrumental neutron activation analysis of nickel. The extent of the interference of the ⁵⁸Co depends on the ratio of the fluxes of the fast and thermal neutrons. A method of selective removal of cobalt, based on extraction with -nitroso--naphthol has been developed for the purpose of radiochemical NAA. Separation yields have been determined for 36 elements. The detection limits obtainable with both the instrumental and the radiochemical method are <10^–4 g/g for the elements Au, Eu, Ir, La, Sc and Sm, between 10^–4 and 10^–3 g/g for Cr, Cs, Hf, Hg, Lu, Re, Sb, Ta, Th, Tm and Yb, between 10^–3 and 10^–2 g/g for As, Ag, Br, Ce, Ga, Na, Ru, Se, W and Zn, and in the range 0.01–1 g/g for Ba, Cd, Co, Fe, In, K, Mo, Nd, Pd, Rb, Sn, U and Zr.     

Trace element analysis of some shaving powders commonly marketed in Nigeria using instrumental neutron activation analysis

Instrumental neutron activation analysis (INAA) technique has been employed viak ₀ approximation method to determine elemental composition of five shaving powders commonly marketed in Nigeria. Fe displayed the highest concentrations in the range 1000–2000 g·g^–1. Na and Zn concentrations were established in the range 200–400 g·g^–1. Heavy elements like Ga, La, Cr, Co, Ag, Ce and Nd concentrations were noted in the lower range of 1–10 g·g^–1 Br, As, Sb, Sm, Eu, W, Cs, Tb, Yb, Hf, Ta, Th and U concentrations were established in even lower traces in the <1 g·g^–1 range. Results obtained for a certified reference material, CANMET BL-1 and CERT (in house) Kaolin standard compared favourably with the literature values thus establishing the results presented for the shaving powders.     

Using enzymes isolated from diverse sources to determine metal ion cofactors

Oxidoreductases and hydrolases isolated from different sources (horseradish and peanut peroxidases, alcohol dehydrogenases from bakers yeast and horse liver, and alkaline phosphatases from Escherichia coli, chicken and seal intestine) were used to determine their metal ion cofactors: Fe(III), Zn(II) and Mg(II), respectively. Studying the effects of the metal ion cofactors on the catalytic activity of the enzymes of different origin showed that the extent of their inhibition, activation, or reactivation of their apoenzymes depended on the structure and accessibility of the enzyme active site, which varies among the biocatalysts isolated from different sources. The developed procedures are based on the inhibiting (Zn(II)) or activating (Mg(II)) effects of the metal ions on the catalytic activity of the enzymes, or on reactivating effects (Fe(III) and Zn(II)) on the apoenzymes. The procedures are characterized by high sensitivity and selectivity; the detection limits of Fe(III) using horseradish peroxidase, Zn(II) using alcohol dehydrogenase from bakers yeast, alkaline phosphatase from seal intestine and its apoenzyme, and Mg(II) using alkaline phosphatase from chicken intestine equal 10 ng L^–1, 20 ng L^–1, 3 g L^–1, 8 g L^–1 and 0.2 g L^–1, respectively.Presented at the 8th Symposium Kinetics in Analytical Chemistry, Rome, Italy, 5–8 July 2004.     

Rare earths and other trace elements in cretaceous clays from central Portugal

Eight rare-earth elements (REE), namely La, Ce, Nd, Sm, Eu, Tb, Yb, and Lu, as well as other elements (Na, K, Sc, Cr, Fe, Co, Rb, Cs, Ba, Hf, Ta, and Th), have been determined in fifteen cretaceous clay samples of continental facies by instrumental neutron activation analysis. It was found that the REE contents are variable in absolute and relative values, but the means of these values are similar to those of European, shales. Analyses have also been made of the fractions <38 m and <2 m (clay-sized). The mineral contents of the clay-sized fraction were determined semi-quantitatively by X-ray diffraction. The results suggest the preferential presence of REE, Hf, and Th in fractions 2–38 m, which can be explained by the presence of apatite, monazite, and zircon. A correlation study of chemical and mineralogical data of the clay-sized fraction showed that kaolinite is correlated with REE, specially the lighter ones; illite with K, Rb, and Cs; and smectite with Na.     

Trace and minor elements in four commercial honey brands

Instrumental neutron activation analysis was used to measure the concentrations of 24 elements in four honey brands commercially available in Austin, Texas (USA). The measured elements (and concentration) were: As, (<30 ng/g); Ba, (<2 g/g); Br, (0.24–0.49 g/g); Ce, (<20 ng/g); Co, (9–180 ng/g); Cr, (37–64 ng/g); Cs, (<3–45 ng/g); Fe, (<4–15.9 g/g); Hf, (<3 ng/g); Hg, (1 ng/g); K, (91–230 g/g); La, (<4 ng/g); Na, (20.3–25.3 g/g); Ni, (0.39–0.77 g/g); Rb, (68–340 ng/g); Sb, (13–61 ng/g); Sc, (<0.3–200 ng/g); Se, (<20 ng/g); Sm, (<9 ng/g); Sr, (<2 ng/g); Th, (<4 ng/g); U, (<30 ng/g); Zn, (3.36–4.61 g/g); and Zr, (<0.5–0.84 g/g). The results obtained were compared to the concentration of the same elements in honey produced or commercially available in Turkey, Mexico, El-Salvador, China, Czechoslovakia and Yugoslavia.     

Electroreduction of α-glucose on CNT/graphite electrode modified by Zn and Zn–Fe alloy

Electroreduction of -glucose to form sorbitol on Zn/CNTs and Zn alloy/CNTs electrodes has been investigated in this paper. Carbon nanotubes (CNTs) used in this paper are grown directly on graphite disks by chemical vapor deposition. Zn and Zn alloy are electrodeposited on the activated CNTs/graphite electrode by pulse galvanostatic method. The micrographs of Zn/CNTs and Zn alloy/CNTs electrodes are characterized by scanning electron microscopy. The results show that the current efficiency of -glucose reduction on CNTs electrodes is much better than that on flat Zn electrodes. The order of the current efficiency on different electrodes is as follows: Zn/CNT (0.58) Zn–Fe/CNT (0.57)>Zn–Ni/CNT (0.43) Zn/graphite (0.42)>Zn (0.40). It indicates that CNTs have good potential application in electrosynthesis. Additionally, effects of some operating parameters, such as pH, temperature and -glucose concentration, on the current efficiency of -glucose reduction are also discussed.     

Electrical Double Layer Structure in Surface-Inactive Electrolytes on a Liquid Cd–Ga Electrode in Methanol and Propylene Carbonate

Differential capacitance curves and potentials of zero charge are obtained for liquid Cd–Ga electrodes in methanol and propylene carbonate solutions of a surface-inactive electrolyte. It is found that double-layer characteristics of the Cd–Ga electrode differ from those of a Ga electrode both in nonaqueous solutions and in water. The lyophilic nature of the Cd–Ga electrode, relative to methanol and propylene carbonate, is shown to approach that of the In–Ga electrode. In the absence of a metal–solvent chemisorption interaction, the difference between reciprocal metallic capacitances for Cd–Ga and Hg electrodes is independent of the solvent nature. The chemisorption interaction between the solvents and Cd–Ga, Ga, and In–Ga electrodes increases with the solvents' donor number.     

Multielemental determination in some water samples by neutron activation method

A method was developed for the determination of element concentrations in structured water samples (water with high oligoelements content). Sixteen elements (As, Br, Ca, Ce, Co, Cr, Eu, Fe, K, La, Lu, Na, Sb, Sc, Sm, Zn) were determined in 4 structured water samples and one taken from the water tap. The samples were preconcentrated evaporating 1 1 at atmospheric pressure and obtaining 100–500 mg of dry residue. Measurement accuracy by -spectroscopy was 3–30% and it can be improved by increasing the measurement time. The method allows simultaneous multielement analysis of various water sources and may successfully be used in environmental pollution control.     

Further investigation of some aspects concerning the direct fluorimetric determination of uranium in minerals

Summary Some theoretical and practical aspects concerning the direct fluorimetric determination of uranium in minerals are presented together with a comparison of a series of practical results of this methodology with those obtained by other techniques. The investigation of the reduction of uranium fluorescence by interfering elements (quenching) was continued and further evidence provided that the dependence of this phenomenon on the quencher concentration may be-within certain limits-described by the Lambert absorption law. The characteristic parameter of this dependence, the half-concentration, has been determined for eight further elements, namely Ni, Co, Zn, Cd, Zr, Th, Ce and Cu. Further more the influence of the quencher/uranium ratio on the results of analysis using the internal standard (spike) method has been investigated [with Fe(III) as model quencher] up to Fe(III)/U=5000; there was no dependence observed within the limits of error.

---

Über weitere Aspekte der fluorimetrischen Bestimmung von Uran in Mineralen

Zusammenfassung Einige theoretische und praktische Aspekte der direkten fluorimetrischen Bestimmung des Urans in Mineralen sowie ein Vergleich einer Reihe praktischer, mit dieser Methode erhaltener Analysenergebnisse mit solchen anderer Verfahren wurden aufgezeigt. Die Erforschung der Reduktion der Uranfluoreszenz durch Störstoffe (Lösch-Effekt) wurde fortgesetzt sowie ein weiterer Nachweis gegeben, daß dieses Phänomen innerhalb gewisser Grenzen durch das Absorptionsgesetz von Lambert beschrieben werden kann. Der charakteristische Parameter dieser Beziehung, die Halbkonzentrationld (c1/2), wurde für acht weitere Elemente (Ni, Co, Zn, Cd, Th, Ce und Cu) bestimmt. Weiterhin wurde der Einfluß des Verhältnisses Löscher-Uran auf die Ergebnisse von Analysen nach der internal standard (spike) Methode untersucht, wobei als Modell-Löscher Fe(III) zur Anwendung kam; die Untersuchung erstreckte sich bis zum Verhältnis Fe(III)/U=5000. Innerhalb der Fehlergrenzen wurde keine Abhängigkeit gefunden.

---

---

Presented at the 8th International Microchemical Symposium, Graz, August 25–30, 1980.     

Insertion of 3d- and 4f-Elements into Silver Iodide

The interaction of manganese and some 4f-metals (M) with silver iodide is studied. The samples are obtained by sputtering M onto the surface of polycrystalline AgI films (0.2 m, 300 K) in a vacuum. Optical absorption in the samples is interpreted as the insertion of M ions into AgI with the formation of dopants AgI:M. A new phase with an optical bandgap of 3.7 eV emerges in the samples with elevated concentrations of La, Ce, Pr, Nd, Sm, or Dy (n _M/n _Ag 0.1). X-ray diffraction patterns for such samples with Sm correspond to structures with large interfacial distances, for example, 0.99, 0.87, 0.76, and 0.67 nm. In air, AgI forms in the samples with a new phase; this process is hindered by the sputtered protective coatings. According to optical absorption data, X-ray diffraction, and local microanalysis the Mn insertion into AgI is followed by the formation of a new phase (2Ag:Mn:4I), which may belong with solid electrolytes Ag₂MI₄, where nonmagnetic M are known (Zn, Cd, Sn, Hg, Pb).     

Determination of Heavy Metal Ions in Chinese Herbal Medicine by Microwave Digestion and RP-HPLC with UV-Vis Detection

A new method for the simultaneous determination of heavy metal ions in Chinese herbal medicine by microwave digestion and reversed-phase high-performance liquid chromatography (RP-HPLC) has been developed. The Chinese herbal medicine samples were digested by microwave digestion. Lead, cadmium, mercury, nickel, copper, zinc, and tin ions in the digested samples were pre-column derivatized with tetra-(4-chlorophenyl)-porphyrin (T₄-CPP) to form the colored chelates which were then enriched by solid phase extraction with C₁₈ cartridge and eluted from the cartridge with tetrahydrofuran (THF). The chelates were separated on a Waters Xterra RP₁₈ column by gradient elution with methanol (containing 0.05molL^–1 pyrrolidine-acetic acid buffer salt, pH=10.0) and THF (containing 0.05molL^–1 pyrrolidine-acetic acid buffer salt, pH=10.0) as mobile phase at a flow rate of 0.5mLmin^–1 and detected with a photodiode array detector in the range of 350–600nm. In the original samples the detection limits of lead, cadmium, mercury, nickel, copper, zinc and tin are 4ngL^–1, 3ngL^–1, 6ngL^–1, 5ngL^–1, 2ngL^–1, 6ngL^–1, and 4ngL^–1, respectively. This method was applied to the determination of lead, cadmium, mercury, nickel, copper, zinc and tin in Chinese herbal medicine samples with good results.     

Correction for neutron induced reaction interferences in the NAA k0-standardization method

A study is made of the correction, in k₀-standardized NAA, for interferences caused by fast neutron induced threshold reactions, second order reactions and²³⁵U-fission. The following examples are elaborated: determination of the Cr and Sc concentrations in a reference human serum, corrected for the⁵⁴Fe(n,)⁵¹Cr and⁴⁴Ca(n,;^–; n,)⁴⁶Sc interferences, respectively, and the determination of Zr, Cs, La, Ce, Nd and Sm concentrations in USGS BCR-1 and G-2, corrected for²³⁵U(n, f) interference. A detailed uncertainty analysis and a comparison of the analytical results thus obtained with other literature values proves that the interferences can be accurately corrected for by employing the usual neutron flux monitors in the k₀-method, namely a Zr-foil and a dilute Au–Al alloyed wire.     

Determination of Arsenic in Food Samples by Hydride Generation – Atomic Absorption Spectrometry

A method for the determination of trace amounts of arsenic in food samples using flow injection analysis and atomic absorption spectrometry with hydride generation (FI-HG AAS) was developed. The parameters of the flow injection system and the hydride generation were optimized with respect to reagent concentrations, atomization temperature, injection volume, reaction coil length and carrier flow rate. The limits of detection and quantification were 0.34µgL^–1 and 1.2µgL^–:1, respectively, and the analytical curve is linear up to 30.0µgL^–1 arsenic. The relative standard deviation for 12 replicates varies between 5% for 4.0µgL^–1 As and 1.8% for 30.0µgL^–1 As, with an injection frequency of up to 135h^–1. Interferences from Ni(II), Cu(II), Fe(III), Cr(III), Mo(II), Bi(III), Se(IV), Se(VI), Sb(III) and Sb(V) could be masked with a mixture of ascorbic acid-KI in a 5.0molL^–1 HCl solution. The accuracy of the proposed method was evaluated by using certified reference materials of biological samples, and the method was used to determine the content of arsenic in fish and coffee beans.     

Energy Transfer Electrogenerated Chemiluminescence for the Determination of Sulfite

A simple and novel electrogenerated chemiluminescence (ECL) method for the determination of sulfite has been developed based on the energy transfer ECL process. It was found that a weak ECL signal of sulfite was electrochemically generated on a platinum electrode in neutral aqueous solution. The signal was strongly enhanced by rhodamine B as an energy receptor and further enhanced by the neutral surfactant Tween 80. In 0.10M phosphate buffer solution (pH=7.5) containing 2.0×10^–6gmL^–1 rhodamine B and 0.4% (v/v) Tween 80, the ECL response to the concentration of sulfite at a potential of 0.82V was linear over a range of 1.0×10^–7gmL^–1 to 8.0×10^–6gmL^–1, and the detection limit was 5×10^–8gmL^–1. The relative standard deviation (n=11, 1.0×10^–6gmL^–1) was 3.8%. The proposed method has been successfully applied to the determination of sulfite in pharmaceutical injections and white sugar samples.     

Determination of Total Selenium Content in Cereals and Bakery Products by Flow Injection Hydride Generation Graphite Furnace Atomic Absorption Spectrometry Applying in-situ Trapping on Iridium-Treated Graphite Platforms

A flow injection hydride generation graphite furnace atomic absorption spectrometric (FI-HG-GFAAS) method was applied to the determination of Se in Se-doped and undoped cereals and bakery products. For the purpose of doping, the soils used for the cultivation of the cereals were dosed with Se-doped foliar fertilizers. The samples were dissolved in a mixture of HNO₃ and H₂O₂ solutions using microwave-assisted digestion. The decomposition of H₂Se generated from the sample solutions and the trapping of elemental Se were performed at a temperature of 300°C on an Ir-pretreated integrated graphite platform of a transversally heated graphite atomizer (THGA). For release of the trapped Se within a fairly short atomization time (5s), an atomization temperature of 2200°C was observed to be optimal. The overall efficiency of hydride generation, transport and trapping was 86%.The upper limit of the linear dynamic range of calibration was 10µgL^–1, which corresponds to 0.5µgg^–1 for solid samples. Recovery of the samples spiked with Se^VI solutions was found to be 93±6% on average. The relative standard deviation of the determinations was less than 8%. The limit of detection was found to be 0.06µgL^–1, corresponding to 3ngg^–1 for solid samples. The accuracy of the method was verified with the use of IAEA-155 (whey powder) certified reference material. End-capped THGA tubes resulted in an extension of the linear calibration range compared to that of standard THGAs.The Se content in bakery products made of undoped cereals ranged from 7.7 to 68ngg^–1 (wet weight) in 18 samples, whereas the Se content of the corresponding cereals was found to be below 100ngg^–1 (wet weight). The Se level of cereals grown on soils treated with Se-doped fertilizers ranged from 128 to 1046ngg^–1 (wet weight), and it depended linearly on the Se concentration of the corresponding foliar fertilizer.