镁热还原法制备有序介孔Si/C锂离子电池负极材料及其电化学性能

以SBA-15为前驱体,在660 ℃下通过镁热还原反应得到介孔硅材料,并对其进行碳包覆处理,成功地制备了有序介孔Si/C（OMP-Si/C）复合材料。该OMP-Si/C材料保留了SBA-15模板的有序蜂窝孔道,并且形成具有高堆积密度的莲藕链束结构。文中还提出了一个SBA-15镁热还原液态环境反应模型,探讨了660 ℃下硅的高度有序介孔与莲藕链束结构的形成机理。利用X射线衍射（XRD）仪、扫描电子显微镜（SEM）、透射电子显微镜（TEM）、氮气吸脱附法及拉曼光谱对样品物相和微观形貌进行了表征。这种高度有序介孔Si/C复合材料具有优异的电化学性能,展现出其在第二代锂电池负极材料领域中的潜在应用价值。     

(SBA-15)-ZnS主-客体纳米复合材料的制备与表征

本研究在SBA-15分子筛孔道中制备了纳米ZnS。Zn_{2+首先通过离子交换交换到SBA-15中,通过水热法在SBA-15分子筛孔道中制备了纳米ZnS。(SBA-15)-ZnS复合物由粉末X-线衍射,傅立叶变换红外光谱,低温氮气吸附-解析附技术,固体扩散漫反射光谱以及发光研究进行了表征。粉末X-线衍射研究说明在制备主-客体纳米复合材料中分子筛骨架未被制备过程所破坏,保持完整且结晶度仍很高。傅立叶变换红外光谱表明制备的材料骨架完好。77 K低温氮气吸附-解析附研究表明所制备的复合材料孔体积,孔尺寸以及表面积相对于SBA-15分子筛降低,证明客体ZnS已成功地组装入分子筛孔道中。所制备的纳米复合材料固体扩散漫反射吸收光谱相对于体相ZnS显示出蓝移表明,ZnS已限制在分子筛的孔道中且复合材料中分子筛的孔道对ZnS具有明显的立体限域效应,ZnS成功地组装在SBA-15分子筛的孔道中。发光研究表明,(SBA-15)-ZnS样品出现明显发光现象。主-客体复合材料具有良好的发光性能,有望在发光材料领域中获得应用。}     

Understanding effect of wall structure on the hydrothermal stability of mesostructured silica SBA-15

Mesostructured silica SBA-15 materials with different structural parameters, such as pore size, pore volume, and wall thickness, etc., were prepared by varying the postsynthesis hydrothermal treatment temperature and adding inorganic salts. The hydrothermal stabilities of these materials in steam (100% water vapor) were systematically investigated using a variety of techniques including powder X-ray diffraction, transmission electron microscopy, nitrogen sorption, and (29)Si solid-state NMR. The effect of the pore size, microporosity or mesoporosity, and wall thickness on the stability was discussed. The results show that all of the SBA-15 materials have a good hydrothermal stability under steam of 600 degrees C for at least 24 h. N(2) sorption measurements show that the Brumauer-Emmett-Teller surface area of SBA-15 materials is decreased by about 62% after treatment under steam at 600 degrees C for 24 h. The materials with thicker walls and more micropores show relatively better hydrothermal stability in steam of 600 degrees C. Interestingly, we found that the microporosity of the mesostructured silica SBA-15 is a very important factor for the hydrothermal stability. To the materials with more micropores, the recombination of Si-O-Si bonds during the high-temperature steam treatment may not cause direct destruction to the wall structure. As a result, SBA-15 materials with more micropores show better stability in pure steam of 600 degrees C. Nevertheless, these materials are easily destroyed in steam of 800 degrees C for 6 h. Two methods to effectively improve the hydrothermal stability are introduced here: one is a high-temperature treatment, and another is a carbon-propping thermal treatment. Thermal treatment at 900 degrees C can enhance the polymerization degree of Si-O-Si bonds and effectively improve the hydrothermal stability of these SBA-15 materials in 800 degrees C steam for 12 h. But, this approach will cause very serious shrinkage of the mesopores, resulting in smaller pore diameter and low surface area. A carbon-propping thermal treating method was employed to enhance the polymerization of Si-O-Si bonds and minimize the serious shrinkage of mesopores at the same time. It was demonstrated to be an effective method that can greatly improve the hydrothermal stability of SBA-15 materials in 800 degrees C steam for 12 h. Furthermore, the SBA-15 materials obtained by using the carbon-propping method possess larger pores and higher surface area after the steam treatment at 800 degrees C compared to the materials from the direct thermal treatment method after the steam treatment.     

Characterization and acidic properties of Al-SBA-15 materials prepared by post-synthesis alumination of a low-cost ordered mesoporous silica

A series of Al-containing SBA-15 type materials with different Si/Al ratio, were prepared by post-synthesis modification of a pure highly ordered mesoporous silica SBA-15 obtained by using sodium silicate as silica source, and amphiphilic block copolymer as structure-directing agent. A high level of aluminum incorporation was achieved, reaching an Si/Al ratio of up to 5.5, without any significant loss in the textural properties of SBA-15. These materials were fully characterized by powder X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), ²⁷Al NMR spectroscopy, and N₂ adsorption at 77 K. The acid properties of these materials have been evaluated by NH₃-TPD, adsorption of pyridine and deuterated acetonitrile coupled to FTIR spectroscopy. The effective acidity of these materials was evaluated using two catalytic reactions: 2-propanol dehydrogenation and 1-butene isomerization. The adsorption of basic probe molecules and the catalytic behavior revealed an evolution of the acid properties with the Al content. These studies have shown that the Al-SBA-15 materials contain Brønsted and Lewis acid sites with medium acidity which makes them appropriate to be used as acid catalysts in heterogeneous catalysis, catalytic supports, and adsorbents.     

Amine-functionalized SBA-15 with uniform morphology and well-defined mesostructure for highly sensitive chemosensors to detect formaldehyde vapor

Amine-functionalized SBA-15 with uniform morphology and well-defined mesostructure was prepared using a postgrafting route. The morphology, mesostructure, and functionality of the materials were characterized by scanning electron microscopy, transmission electron microscopy, small-angle X-ray scattering, nitrogen adsorption-desorption, Fourier transform infrared spectroscopy, and solid-state nuclear magnetic resonance spectroscopy techniques. The results show that hexagonal lamelliform SBA-15 with a uniform particle size and short vertical channels plays two significant roles in uniformly dispersing amine-functionalizing groups and effectively adjusting the loadings of the functional groups within the mesopore channels. To confirm the potential application of the hybrids in gas sensors, using amine-functionalized SBA-15 as a sensing material and a quartz crystal microbalance as a transducer, a parts per billion level formaldehyde sensor with high sensitivity (response time about 11 s, recovery time about 15 s) and good chemoselectivity was achieved. This material holds great potential in the area of rapid, sensitive, and highly convenient formaldehyde detection.     

Synthesis of carboxyl-modified rod-like SBA-15 by rapid co-condensation

Carboxyl-modified SBA-15 rod-like mesoporous materials have been synthesized by a facile rapid co-condensation of tetraethylorthosilicate (TEOS) and 2-cyanoethyltriethoxysilane (CTES), followed by hydrolysis of cyanide groups in sulfuric acid. The concentration of carboxylic groups was varied by changing the silica source ratio of CTES/TEOS from 0.05 to 0.3. X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) showed that the uniform ordered mesoporous structure and rod-like morphology of SBA-15 have been preserved even at the high concentration of carboxylic groups employed. Characterization by Fourier transformed infrared spectroscopy (FTIR), solid-state NMR investigation indicated that carboxylic groups have been successfully grafted onto the surface of SBA-15 through siloxane bonds [(O(3))SiCH(2)CH(2)COOH. The negative charges of the modified SBA-15 materials were enhanced by the presence of the carboxylic groups on the surface. The capacity of lysozyme adsorption of the modified SBA-15 materials were found to be significantly improved as compared with pure silica SBA-15. The maximum amount of lysozyme adsorption on carboxyl-modified was increased with the pH of solution increased from 5.5 to 9.0.     

WxC/SBA-16催化剂的制备、表征及催化加氢脱硫性能

以正硅酸乙酯为硅源, 仲钨酸铵为钨源, P123和F127为混合模板剂,采用水热晶化法一步合成了不同钨含量(以n(Si):n(W)表示)的WO3/SBA-16, 然后经甲烷/氢气(V(CH4)/V(H2)=1/4)混和气体程序升温还原碳化(TPC), 制备出了WxC/SBA-16(x=1, 2)催化剂. 采用XRD、N2-吸附/脱附、TEM和FTIR等分析测试技术对样品的结构进行了表征, 并以噻吩作为模型化合物, 对WxC/SBA-16催化剂的加氢脱硫催化活性进行了评价. 结果表明, 在一定钨含量的条件下, WO3/SBA-16和WxC/SBA-16样品仍然保持立方笼状介孔结构, 当n(Si):n(W)为30-10时, 碳化钨的物相为W2C; n(Si):n(W)为7.5时, 碳化钨的物相为W2C和WC. WxC/SBA-16催化剂表现出了良好的加氢脱硫催化性能.     

Synthesis and characterization of surface modified SBA-15 silica materials and their application in chromatography

Hexagonally ordered SBA-15 mesoporous silica spheres with large uniform pore diameters are obtained using the triblock copolymer, Pluronic P123, as template with a cosurfactant cetyltrimethylammonium bromide (CTAB) and the cosolvent ethanol in acidic media. A series of surface modified SBA-15 silica materials is prepared in the present work using mono- and trifunctional alkyl chains of various lengths which improves the hydrothermal and mechanical stability. Several techniques, such as element analysis, nitrogen sorption analysis, small angle X-ray diffraction, scanning electron microscopy (SEM), FTIR, solid-state (29)Si and (13)C NMR spectroscopy are employed to characterize the SBA-15 materials before and after surface modification with the organic components. Nitrogen sorption analysis is performed to calculate specific surface area, pore volume and pore size distribution. By surface modification with organic groups, the mesoporous SBA-15 silica spheres are potential materials for stationary phases in HPLC separation of small aromatic molecules and biomolecules. The HPLC performance of the present SBA-15 samples is therefore tested by means of a suitable test mixture.     

Formation of indium nitride nanorods within mesoporous silica SBA-15

We report the first formation of arrays of InN nanorods inside the nanoscale channels of mesoporous silica SBA-15. In(NO3)3 dissolved in methanol was incorporated into SBA-15 powder without prior pore surface functionalization. Formation of InN nanorod arrays was carried out by ammonolysis at 700 degrees C for 8 h. The final products have been characterized by FT-IR spectra, (29)Si MAS NMR spectra, Raman spectra, XRD patterns, TEM images, nitrogen adsorption-desorption isotherm measurements, and optical spectroscopy. The freestanding InN nanorods observed after silica framework removal with HF solution show diameters of 6-7.5 nm and lengths of 25-50 nm. Formation of a trace amount of In2O3 was also verified. The InN nanorods exhibit a broad band centered at around 550-600 nm, and a band gap energy of 1.5 eV was determined. No light absorption in the near-IR region was measured. The nanorods give a weak emission band centered at around 600 nm. These optical properties are believed to be related to the possible incorporation of oxygen during InN nanorod synthesis.     

Mesoporous SBA-15 materials modified with PW or W active species as catalysts for the epoxidation of olefins with H<Subscript>2</Subscript>O<Subscript>2</Subscript>

Five catalysts containing PW or W active species that anchored onto aminosilylated mesoporous silica SBA-15 by a post-grafting route were prepared and the resulting PW or W/APTES/SBA-15 hybrid materials were characterized by XRD, N₂ adsorption/desorption, surface area analysis, TEM, FT-IR, and ICP (inductively coupled plasma atomic emission spectroscopy). The names of these catalysts have been abbreviated as SBA-15m-a, SBA-15m-b, SBA-15m-c, SBA-15m-d, and SBA-15m-e according to the different active species. The PW or W active species were highly dispersed in the channels of the modified mesoporous materials. The interaction between PW or W species and amino groups grafted on the channel surface of SBA-15 led to the immobilization of PW or W species. Their catalytic activity in the epoxidation of cyclooctene with H₂O₂ as oxidant was investigated. Among them, SBA-15m-a showed the best performance, with 98.9% conversion and 98.4% selectivity. The catalyst could be reused for six times with a little decrease in activity.     

NMR provides checklist of generic properties for atomic-scale models of periodic mesoporous silicas

MCM-41 and SBA-15 silicas were studied by (29)Si solid-state NMR and (15)N NMR in the presence of (15)N-pyridine with the aim to formulate generic structural parameters that may be used as a checklist for atomic-scale structural models of this class of ordered mesoporous materials. High-quality MCM-41 silica constitutes quasi-ideal arrays of uniform-size pores with thin pore walls, while SBA-15 silica has thicker pore walls with framework and surface defects. The numbers of silanol (Q(3)) and silicate (Q(4)) groups were found to be in the ratio of about 1:3 for MCM-41 and about 1:4 for our SBA-15 materials. Combined with the earlier finding that the density of surface silanol groups is about three per nm(2) in MCM-41 (Shenderovich, et al. J. Phys. Chem. B 2003, 107, 11924) this allows us to discriminate between different atomic-scale models of these materials. Neither tridymite nor edingtonite meet both of these requirements. On the basis of the hexagonal pore shape model, the experimental Q(3):Q(4) ratio yields a wall thickness of about 0.95 nm for MCM-41 silica, corresponding to the width of ca. four silica tetrahedra. The arrangement of Q(3) groups at the silica surfaces was analyzed using postsynthesis surface functionalization. It was found that the number of covalent bonds to the surface formed by the functional reagents is affected by the surface morphology. It is concluded that for high-quality MCM-41 silicas the distance between neighboring surface silanol groups is greater than 0.5 nm. As a result, di- and tripodical reagents like (CH(3))(2)Si(OH)(2) and CH(3)Si(OH)(3) can form only one covalent bond to the surface. The residual hydroxyl groups of surface-bonded functional reagents either remain free or interact with other reagent molecules. Accordingly, the number of surface silanol groups at a given MCM-41 or SBA-15 silica may not decrease but increase after treatment with CH(3)Si(OH)(3) reagent. On the other hand, nearly all surface silanol groups could be functionalized when HN(Si(CH(3))(3))(2) was used.     

六方平板状氨基-甲基双官能化SBA-15的合成及对胆红素的吸附

以氨丙基甲基二乙氧基硅烷和正硅酸乙酯为硅源,三嵌段共聚物P123为模板剂,无机盐KCl为助剂,酸性条件下一步法合成了氨基-甲基双官能化SBA-15（AMS）. XRD,FTIR,BET,29Si MAS NMR,SEM及HRTEM等表征结果表明：无机盐不仅提高了AMS材料的介孔有序度,而且控制样品形貌从六方平板状向纤维状转变. 胆红素吸附实验表明：六方平板状AMS比纤维状AMS和纯SBA-15具有更快的吸附速率和更大的吸附容量,这可能是六方平板状形貌易于胆红素扩散以及双官能基团（甲基,氨基）增加了对胆红素吸附作用力的结果.     

三丁基锡/SBA-15功能配合物的合成、表征及对Friedel-Crafts反应的选择性催化

将三丁基氯化锡与SBA-15介孔分子筛在N2气气氛中进行回流反应,得到有机锡无机配合物(C4H9)3Sn-O-SBA-15[Bu3SnS]。 利用X射线衍射(XRD)、透射电子显微镜(TEM)、氮气吸附脱附、固体核磁（NMR）和吡啶吸附脱附红外光谱分析(Py-IR)等方法对产物的组成、结构和性质进行了表征。 结果表明,产物Bu3SnS具有高度有序的六方介孔结构,与SBA-15相比,Bu3SnS比表面积、孔容和孔径变小,酸性增强。 Bu3SnS对苯甲醚Friedel-Crafts酰基化反应具有优异的催化性能,当反应温度为130 ℃,n（苯甲醚）∶n（苯甲酰氯）=1.0∶2.0,w（cat）=6%（相对于苯甲醚用量）,反应时间为5 h,苯甲醚的转化率达到76.0%,对甲氧基二苯酮（p-MBP）选择性达到97.8%。     

Synthesis and characterization of SBA-3, SBA-15, and SBA-1 nanostructured catalytic materials

A highly ordered large pore mesoporous silica molecular sieve SBA-3, SBA-15, Al-SBA-15, and SBA-1, were developed and characterized by XRD, BET, FTIR, SEM, and NMR-MAS. The catalytic materials were synthesized using different raw materials and operation conditions. These materials contain a regular arrangement of uniform channels with diameters between 1.8 and 10 nm, high specific surface area and high specific pore volume. The designed methods were effective for the synthesis, presenting each mesostructured materials, patterns of XRD and other characteristics corresponding to the reported ones in literature. The new route employed to synthesize Al-SBA-15, generates a catalyst with only aluminum in tetrahedral form, according to the data of (27)Al NMR-MAS. However, several reports indicated that the coordination of the Al atoms changes below the Si/Al ratio of 45, presenting peaks corresponding to penta and hexa-coordinated aluminum, which are absent in our samples (Si/Al = 50 and 33).     

Calix[4]arene derivative functionalized lanthanide (Eu, Tb) SBA-15 mesoporous hybrids with covalent bonds: assembly, characterization and photoluminescence

Three kinds of novel macrocylic calix[4]arene derivatives functionalized SBA-15 type of mesoporous hybrids (Calix-S15, Calix-NO(2)-S15 and Calix-NH(2)-S15) are synthesized by co-condensation of tetraethoxysilane (TEOS) and modified organic ligand (Calix-Si, Calix-NO(2)-Si and Calix-NH(2)-Si) in the presence of Pluronic P123 surfactant as a template. The structural preservation of these three parent materials is confirmed by FTIR spectra, (29)Si MAS NMR spectra, XRD pattern, and N(2) adsorption-desorption measurements. The ternary mesoporous luminescent hybrids containing Ln(3+) (Eu(3+), Tb(3+)) complexes covalently attached to the functionalized ordered mesoporous SBA-15, which are designated as Ln(Calix-S15)phen, Ln(Calix-NO(2)-S15)phen and Ln(Calix-NH(2)-S15)phen, are obtained by introducing lanthanide ions and 1,10-phenanroline into the corresponding parent material via covalent bond assembling methods. XRD pattern, TEM and N(2) adsorption-desorption measurements are employed to characterize the mesostrcture of the resulting lanthanide mesoporous hybrids. The photoluminescent behavior (luminescence, lifetime, quantum efficiency, and energy transfer) for these chemically bonded mesoporous hybrids is studied in detail. Also, their quantum efficiencies are determined, which indicates that the different mesoporous hybrid material systems derived from different functionalized calix[4]arene derivative bridges present different luminescence behavior.     

TEPA在SBA-15(P)上的嫁接形态及其对CO2吸附性能的影响

通过控制浸渍方法和其过程将四乙烯五胺(TEPA)负载到SBA-15原粉上制备氨基功能化的CO2吸附材料TEPA/SBA-15(P).利用X射线衍射(XRD)、氮吸附、元素分析和傅里叶变换红外(FTIR)光谱等手段对各种吸附材料进行表征分析,并对其CO2吸附能力进行评价.结果表明:TEPA乙醇溶液的动态浸渍过程可以使有机胺高度均匀地负载到SBA-15(P)的孔道内,并形成有利于CO2吸脱附的键合形式.提出了TEPA在SBA-15(P)上的键合作用机制,一方面TEPA的端基氨(-NH2)与载体中的表面羟基(-OH)和醚键(C-O-C)形成氢键,提高了TEPA的分散度;另一方面,TEPA乙醇溶液的动态浸渍过程有效地避免了TEPA分子间或分子内氢键的形成,从而使有机胺TEPA氨基官能团具有较高的吸附容量.     

Controlling the density of amine sites on silica surfaces using benzyl spacers

The synthesis and characterization of benzyl-spaced aminopropyl-functionalized mesoporous silica is reported by a method designed to reduce silanol-amine and amine-amine interactions. The new material is characterized by N(2) physisorption, thermogravimetric analysis, potentiometric titration, X-ray diffraction, FT-Raman spectroscopy, and (13)C and (29)Si solid-state NMR spectroscopy. The degree of clustering of the amines is studied by solid-state fluorescence spectroscopy of 1-pyrenecarboxylic acid bound to the deprotected benzyl-spaced aminosilica. The results obtained provide evidence of an amine loading comparable to traditional dense amine grafting approaches on SBA-15. Thermogravimetric analysis, FT-Raman spectroscopy, and (13)C solid-state NMR spectroscopy results show evidence that the protected imine can be quantitatively cleaved to yield the corresponding amine. As evidenced by fluorescence spectroscopy, the benzyl-spaced material is isolated enough to prevent excimer formation of the probe molecule, unlike aminopropyl-functionalized silica materials prepared by traditional grafting approaches.     

Formation of titanium nitride nanoparticles within mesoporous silica SBA-15

We report the first synthesis of titanium nitride (TiN) nanoparticles inside the nanoscale channels of mesoporous silica SBA-15. The TiN precursor, Ti(NMe(2))(4) in toluene, was incorporated into the methyl group-modified channels of the SBA-15 powder. The functionalization of pore surfaces with methyl groups generates hydrophobic surfaces that facilitate impregnation with Ti(NMe(2))(4) and minimizes reactions between the TiN precursor and the hydroxyl groups on the surface of SBA-15. Formation of TiN nanoparticles inside the mesoporous channels of SBA-15 was carried out by subsequent ammonolysis at high temperatures (700-750 degrees C). The final products have been characterized by TEM and EELS images, powder XRD patterns, FTIR spectra, UV-vis absorption spectra, and nitrogen adsorption isotherm measurements to confirm the presence and distribution of TiN nanoparticles in the SBA-15 samples.     

共价嫁接钌(Ⅱ)配合物SBA-15介孔分子筛的光学氧传感行为

使用P123(EO20PO70EO20)作为表面活性剂, 并通过正硅酸乙酯与含可以水解烷氧基团的[Ru(Phen)2Phen—Si]2+功能化配合物的水解和共缩聚反应, 成功地制备了共价嫁接[Ru(Phen)3]2+分子片断的复合SBA-15介孔杂化材料. 用红外光谱和发光强度猝灭Stern-Volmer曲线对样品进行了表征, 并分别用Demas双格位模型以及Lehrer模型对所获得的复合Ru-SBA-15样品的Stern-Volmer曲线进行了拟合. 实验结果表明, 所制备的传感样品对氧气具有较高的传感灵敏度. 发光分子与分子筛之间产生强有力的CH2—Si化学键使得该杂化材料具有可逆的氧传感信号和较好的光化学稳定性.     

Ni-W Catalysts Supported on Mesoporous SBA-15: Trace W Steering CO2 Methanation

Aseries of Ni-W catalysts supported on mesoporous SBA-15 with different Ni:W ratios(Ni_xW/SBA-15, Ni-5%, x=1,10,50) was prepared and fully characterized by powder X-ray diffraction(PXRD), Brunner-Emmet-Teller(BET), transmission electronic microscopy(TEM), H₂-temperature programmed reduction(H₂-TPR), and X-ray photoelectron spectroscopy(XPS). High-resolution TEM images, XPS measurements, H₂-TPR experiments coupled with PXRD results determined the evolution of Ni and W species. It is found that a trace amount of W from H₂WO₄ can significantly improve Ni dispersion on SBA-15 (Ni₅₀W/SBA-15) with Ni⁰ andnon-stoichiometric WO_x species as small as ca. 3.6 nm. The prepared Ni_xW/SBA-15 was utilized for CO₂ hydrogenation, which showed that a higher W content restrained the CO₂ hydrogenation while a lower W ratio promoted both conversion rate and selectivity for methane compared with Ni/SBA-15. The Ni₅₀W/SBA-15 catalyst showed the best performance with a 93.3% CO₂ conversion rate and 99.7% selectivity for methane at 400 ^oC under 0.1 MPa and maintained ca. 97% initial performance for 24 h. Tracking product evolution experiments by in-situ Fourier transform infrared spectrascopy(FTIR) indicated that a small amount of W can modify the surface of Ni particles by geometric coverage and electronic modification, which facilitates the adsorption of the CO intermedia and results in the formation of CH₄. This work provides a new clue to fabricating efficient CO₂ conversion bimetallic materials.