Structure and solution properties of cyanoethyl celluloses synthesized in LiOH/urea aqueous solution

Cyanoethyl celluloses (CECs) with different degree of substitution (DS) were synthesized by homogeneous reaction of cellulose (cotton linter pulp and absorbent cotton) with acrylonitrile (AN) in LiOH/urea aqueous solutions. The reaction showed quick reactivity and high transfer efficiency of etherification agent. The DS values of CECs were controlled by varying the molar ratio of AN to anhydroglucose unit (AGU) and the cellulose concentration. The DS values of the CEC-1–CEC-10 increased from 0.27 to 1.78 with increasing molar ratio of AN to AGU from 0.5:1 to 9:1. While the CEC-11–CEC-21 with DS values of 0.26–1.81 could be obtained by adjusting the molar ratio from 1:1 to 27:1. The relative reactivity of hydroxyl groups is in the order of C-6 > C-2 > C-3. The DS values of the water-soluble derivatives are in the range of 0.47–1.01. As the DS values increase to 1.37, CEC samples can not be dissolved in water or dilute alkali solution, but have good solubility in organic solvents, such as DMSO, DMF and pyridine. The dilute solution properties and molecular parameters of the CEC samples were studied by static light scattering and dynamic light scattering. The results indicated that the water-soluble samples could form a small number of aggregates spontaneously in 0.9 wt% NaCl aqueous solution, while the water-insoluble samples showed extended stiff chains in 0.5% LiCl–DMAc.     

The effect of subcritical carbon dioxide on the dissolution of cellulose in the ionic liquid 1-ethyl-3-methylimidazolium acetate

The ionic liquid (IL) 1-ethyl-3-methylimidazolium acetate ([emim][OAc]) readily dissolves high concentrations of cellulose. However, the high viscosity of [emim][OAc] (162 cP at 20 °C) could limit its use as a solvent for cellulose. Dissolved CO₂ has been shown to decrease the viscosity of ILs. In this study, a 50 psi CO₂ environment was applied for the dissolution of cellulose in [emim][OAc] to determine if the cellulose dissolution could be enhanced. Dissolution profiles of 4 wt% cellulose dissolved in [emim][OAc] were obtained over a 24 h period. A 75% increase in the amount of dissolved cellulose was observed with the application of a 50 psi CO₂ environment.     

Effects of temperature and molecular weight on dissolution of cellulose in NaOH/urea aqueous solution

Dissolution of cellulose having different viscosity-average molecular weight (M _η ) in 7 wt%NaOH/12 wt%urea aqueous solution at temperature from 60 to −12.6°C was investigated with optical microscope, viscosity measurements and wide X-ray diffraction (WXRD). The solubility (S_a) of cellulose in NaOH/urea aqueous solution strongly depended on the temperature, and molecular weight. Their S_a values increased with a decrease in temperature, and cellulose having M _η below 10.0 × 10⁴ could be dissolved completely in NaOH/urea aqueous solution pre-cooled to −12.6°C. The activation energy of dissolution (E_a,s) of the cellulose dissolution was a negative value, suggesting that the cellulose solution state had lower enthalpy than the solid cellulose. The cellulose concentration in this system increased with a decrease of M _η to achieve about 8 wt% for M _η of 3.1 × 10⁴. Moreover, cellulose having 12.7 × 10⁴ could be dissolved completely in the solvent pre-cooled to −12.6°C as its crystallinity (χ _c) decreased from 0.62 to 0.53. We could improve the solubility of cellulose in NaOH/urea aqueous system by changing M _η , χ _c and temperature. In addition, the zero-shear viscosity (η ₀ ) at 0°C for the 4 wt% cellulose solution increased rapidly with an increase of M _η , as a result of the enhancement of the aggregation and entanglement for the relatively long chains.     

Celluloses in an ionic liquid: the rheological properties of the solutions spanning the dilute and semidilute regimes

The ionic liquid of 1-allyl-3-methylimidazolium chloride ([amim]Cl) was used as the good solvent to dissolve celluloses. Cellulose concentration covers the range of 0.1-3.0 wt %, spanning both the dilute and semidilute regimes. The rheological properties of the cellulose ionic liquid solutions have been investigated by steady shear and oscillatory shear measurements in this study. In the steady shear measurements, all the cellulose solutions show a shear thinning behavior at high shear rates; however, the dilute cellulose solutions show another shear thinning region at low shear rates, which may reflect the characteristics of the [amim]Cl solvent. In the oscillatory shear measurements, for the dilute regime, the reduced dimensionless moduli are obtained by extrapolation of the viscoelastic measurements for the dilute solutions to infinite dilution. The frequency dependences of the reduced dimensionless moduli are intermediate between the predictions from the Zimm model and elongated rodlike model theories, while the fitting by using a hybrid model combining these two model theories agrees well with the experimental results. For the semidilute regime, the frequency dependences of moduli change from the Zimm-like behavior to the Rouse-like behavior with increasing cellulose concentration. In the studied concentration range, the effects of molecular weight and temperature on solution viscoelasticities and the relationship between steady shear viscosity and dynamic shear viscosity are presented. Results show that the solution viscoelasticity greatly depends on the molecular weight of cellulose; the empirical time-temperature superposition principle holds true at the experimental temperatures, while the Cox-Merz rule fails for the solutions investigated in this study.     

Strukturviskosität von verdünnten Lösungen von Biopolymeren

The importance of the rheological behaviour of solutions of macromolecules is briefly evaluated. The viscosity of the solutions depends on concentration, shear rate and time of shear, this relation being determined by the structure of the dissolved molecules. In dilute solutions shear dependence of viscosity is very frequently caused by the preferential orientation of anisotropic molecules. In such a case the particle dimensions can be calculated from the true limiting viscosity number, an anisotropy factor, the rotational diffusion constant and the effective particle density. These numbers can be derived from the flow curve, which has been extrapolated to zero concentration. It is necessary to measure the flow curve at shear gradients, which are sufficiently low to allow for an extrapolation to vanishing shear rate. By comparing the experimental flow curve with a choice of theoretical ones, the rotational diffusion constant and the anisotropy factor (axial ratio) can be found. From the limiting viscosity number and the axial ratio, the particle density can be calculated.     

A new bio-based nanocomposite: fibrillated TEMPO-oxidized celluloses in hydroxypropylcellulose matrix

Utilization of TEMPO-oxidized celluloses in bio-based nanocomposites is reported for the first time. TEMPO-oxidized wood pulps (net carboxylate content 1.1 mmol/g cellulose) were fibrillated to varying degrees using a high intensity ultrasonic processor. The degree of fibrillation was controlled by varying sonication time from 1 to 20 min. The sonication products were then characterized independently and as fillers (5 wt% loading) in hydroxypropyl cellulose nanocomposite films. Nanofibril yields ranging from 11 to 98 wt% (on fiber weight basis) were obtained over the range of sonication times used. Suspension viscosities increased initially with sonication time, peaked with gel-like behavior at 10 min of sonication and then decreased with further sonication. The thermal degradation temperature of unfibrillated oxidized pulps was only minimally affected (6 °C decrease) by the fibrillation process. Dynamic mechanical analysis of the nanocomposites revealed strong fibril-matrix interactions as evidenced by remarkable storage modulus retention at high temperatures and a suppression of matrix glass transition at “high” (~5 wt%) nanofibril loadings. Creep properties likewise exhibited significant (order of magnitude) suppression of matrix flow at high temperatures. It was also believed, based on morphologies of freeze-fracture surfaces that the nanocomposites may be characterized by high fracture toughness. Direct fracture testing will however be necessary to verify this suspicion.     

Anomalous reinforcing effects in cellulose gel-based polymeric nanocomposites

Cellulose-synthetic polymer nanocomposite films were prepared by immersion of cellulose gel in polymer solutions followed by dry casting. The cellulose hydrogel was prepared from aqueous alkali-urea solution. As the synthetic polymer, polystyrene (PS) and poly(methyl methacrylate) (PMMA) were used. The polymer content could be changed between 10 and 80% by changing polymer concentration of immersing solution. While the mechanical properties of the cellulose-PMMA composite films showed a nearly linear dependence on PMMA content, those of cellulose-PS composites showed an anomalous behavior; both tensile strength and Young’s modulus showed prominent maxima at 15–30 wt% PS contents. This anomaly may have resulted from the specific interaction between the aromatic ring of PS and the hydrophobic plane of the glucopyranoside. Both PMMA and PS composite films showed significant improvements in dimensional thermal stability; up to 25 wt% synthetic polymer content, the coefficient of thermal expansion (CTE) was as low as ca. 30 ppm/K, about 1/3 of the pure polymers. This indicates that the regenerated cellulose network is effective in suppressing thermal expansion of the synthetic polymers.     

Rheological Properties of Hydrophobically Modified Poly(acrylic acid) in Mixed Solutions

Hydrophobically modified poly(acrylic acid) (HMPA) with single-tailed pendant side groups was prepared by precipitation polymerization. The effects of polymer concentration, surfactant and co-solvent on the solution properties of HMPA were investigated. HMPA solutions showed good viscosity enhancement and typical shear thinning behavior with increasing concentration. The surfactant TX-10 and co-solvent ethylene glycol gave rise to factors that changed the hydrophobic interactions and in turn the rheology behavior of the solutions. The transient associative network of HMPA in ethylene glycol + water mixed solutions was retained as the temperature was decreased to below 0 °C.     

Influence of water on the dissolution of cellulose in selected ionic liquids

Cellulose (7% water) was thoroughly dispersed in various ionic liquids (IL) and the turbidity of the mixture was investigated to distinguish real dissolution from fine dispersion. The dissolving ability of 1-butyl-3-methylimidazolium chloride (BMIMCl know cellulose solvent) and 11 other commercial IL (not reported as cellulose solvents) was studied. From the latter, only 1,3-dimethylimidazolium dimethylphosphate (DMIMDMP) could dissolve cellulose. The influence of water content on the real dissolution of cellulose in these two IL was investigated. The maximum theoretical amount of dissolved anhydrous cellulose in the IL was determined by extrapolation methodology at different temperatures. For cellulose in BMIMCl, it was 8.75 g/100 g of IL at 95 °C. DMIMDMP could achieve real cellulose dissolution only in a practically anhydrous system (2.3 g/100 g of IL at 30 °C) but dissolution was physically limited by high viscosity.     

Enhanced deconstruction and dissolution of lignocellulosic biomass in ionic liquid at high water content by lithium chloride

Fabricating an aqueous ionic liquid (IL) for deconstruction and dissolution of lignocellulose is attractive because addition of water could reduce the cost and viscosity of the solvent and improve the biomass processing, but the solvating power of the IL is usually depressed in the presence of water. In the present study, an aqueous IL consisting of 1-butyl-3-methylimidazolium chloride (BmimCl), water, and lithium chloride was fabricated for efficient deconstruction and dissolution of lignocellulose (bamboo). The dissolution of cell wall components (cellulose, lignin, and hemicelluloses) in the aqueous IL was investigated. The results indicated that the presence of water significantly reduced the solvating power of BmimCl; For example, 11.5 % water decreased the dissolution of bamboo in BmimCl from ~97 to ~53 %. Dissolution of cellulose and lignin was specifically depressed. However, addition of lithium chloride was able to improve the tolerance of BmimCl to water and enhance the deconstruction and dissolution of biomass in BmimCl with high water content. It was found that approximately 80 % bamboo could be dissolved in solvent consisting of 45 wt% BmimCl and 55 wt% LiCl·2H₂O (25 wt% overall water content in the solvent). In particular, lignin and hemicelluloses were selectively dissolved by 96 and 92 %, respectively. The undissolved residue was predominantly composed of cellulose (~86 %) with a small amount of lignin (<5 %). BmimCl-LiCl-H₂O is a promising and effective solvent system with low cost and viscosity for biomass processing.     

Rheological properties of carboxymethyl cellulose (CMC) solutions

In this study, we investigated the way of predicting two critical concentrations of sodium carboxymethyl cellulose (CMC) solutions using simple experimental procedures with a rotational rheometer. It was found that, above a critical shear rate, all CMC solutions (0.2 to 7 wt.%) exhibit shear-thinning behavior and the flow curves could be described by the Cross model. A first critical CMC concentration c*, transition to semidilute network solution, was determined using the following methods (1) study of the flow curve shapes, (2) Cross model parameters, (3) plot of the specific viscosity vs the overlap parameter, and (4) empirical structure–properties relationships. Furthermore, both creep and frequency-sweep measurements showed that the solutions behaved as viscoelastic materials above a second critical CMC concentration c** (transition to concentrated solution). The characterization of CMC solutions was completed with a time-dependent viscosity study that showed that the CMC solutions exhibited strong thixotropic behavior, especially at the highest CMC concentrations.     

Rheological characterization of the dilatant flow behavior of highly substituted hydroxypropylmethyl- cellulose solutions in the presence of sodium lauryl sulfate

 The flow behavior of aqueous solutions of three highly substituted, hydrophobic hydroxypropylmethylcelluloses (HPMC) in mixtures containing the anionic surfactant sodium lauryl sulfate (SLS) was investigated both rheo-mechanically and rheo-optically. For the first time it was possible to demonstrate dilatant flow in these systems, a phenomenon which is otherwise only known of some suspensions and associative thickening solutions. Without addition of SLS, the aqueous HPMC solutions showed the predicted flow behavior of polymer solutions, and the Cox–Merz rule was fulfilled. With the addition of SLS to these HPMC solutions, the least hydrophobic HPMC displayed no dilatancy. The solutions of a more hydrophobic HPMC with SLS exhibited on the one hand an increase in viscosity, and on the other hand shear thinning as well as shear thickening. The most hydrophobic HPMC displayed more clearly the effects of an SLS-dependent viscosity increase and the appearance of dilatant flow. At constant HPMC concentration (0.5% w/w), a maximum increase in viscosity (factor 15) was observed in the critical micelle concentration range for SLS. By rheo-optical measurements it was possible to detect an unusually pronounced alignment of the polymer segments as well as a sharp increase in the birefringence values, even before the macroscopic occurrence of dilatant flow. According to the existing network theories, this behavior of the aqueous solutions of highly substituted HPMCs in mixture with SLS has been interpreted as a shear-induced transition from intra-molecular to intermolecular interactions. Received: 4 February 1998 Accepted: 13 March 1998     

Semidilute solution structure of cellulose in an ionic liquid and its mixture with a polar organic co‐solvent studied by small‐angle X‐ray scattering

Structural and thermodynamic properties of cellulose solutions in the ionic liquid 1‐ethyl‐3‐methylimidazolium acetate (EMIMAc) and its binary mixtures with N,N‐dimethyl formamide (DMF) are studied by small‐angle X‐ray scattering (SAXS). These measurements indicate molecular dissolution of the cellulose chains without any significant aggregation. The power–law relationships of the evaluated correlation length and osmotic modulus to concentration exhibit exponents of ?0.76 and 2.06 for EMIMAc and ?0.80 and 2.14 for DMF/EMIMAc solvent mixture, respectively. Thus, these solvents can be considered to be good solvents for cellulose. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55 , 888–894     

Conductance of Dilute Hydrochloric Acid Solutions to 458 K and 1.4 MPa

Electrical conductance measurements were made on dilute solutions of hydrochloric acid to 458 K and 1.4 MPa with a flow instrument. These measurements agree well with those of previous authors. The conductance theory of Fuoss and Hsia as given by Fernandez-Prini (FHFP), was fit to these measurements. It was found that this theory adequately described the present results with a single parameter, the limiting conductance at infinite dilution Λ°(HCl). Within their estimated accuracy, reported literature results of Λ°(HCl) between 264.15 and 579 K and high pressures were found to be represented by a five-parameter equation that was a function of the solvent viscosity, temperature and pressure. This equation along with the FHFP theory permits accurate calculation of the conductance of dilute hydrochloric acid solutions at high temperatures and pressures. Electronic Supplementary Material  The online version of this article () contains supplementary material, which is available to authorized users.     

Influence of ZnO on the properties of dilute and semi-dilute cellulose-NaOH-water solutions

The influence of ZnO as cellulose-8%NaOH-water solution stabilizer against gelation is studied. Cellulose intrinsic viscosity in 8%NaOH-water as a function of solution temperature is investigated in the presence and absence of ZnO. The addition of ZnO did not bring any improvement in terms of solvent thermodynamic quality. Non-dissolved ZnO particles were observed above 0.8–0.9% ZnO in 8%NaOH-water. Gelation of cellulose-8%NaOH solutions with and without ZnO are studied for various cellulose and ZnO concentrations (4–6% and 0–1.5%, respectively) in a wide range of temperatures (−5 °C to 50 °C). Gelation times were exponentially increasing with increasing ZnO concentration and with decreasing cellulose concentration and solution temperature. Gelation times of cellulose-NaOH-water-ZnO systems were found to follow a semi-empirical model correlating these three parameters. We suggest that ZnO is acting as water molecular “binder” stabilizing cellulose-NaOH-water solutions.     

Viscoelasticity and Solution Stability of Cyanoethylcellulose with Different Molecular Weights in Aqueous Solution

Water-soluble cellulose ethers are widely used as stabilizers, thickeners, and viscosity modifiers in many industries. Understanding rheological behavior of the polymers is of great significance to the effective control of their applications. In this work, a series of cyanoethylcellulose (CEC) samples with different molecular weights were prepared with cellulose and acrylonitrile in NaOH/urea aqueous solution under the homogeneous reaction. The rheological properties of water-soluble CECs as a function of concentration and molecular weight were investigated using shear viscosity and dynamic rheological measurements. Viscoelastic behaviors have been successfully described by the Carreau model, the Ostwald-de-Waele equation, and the Cox–Merz rule. The entanglement concentrations were determined to be 0.6, 0.85, and 1.5 wt% for CEC-11, CEC-7, and CEC-3, respectively. All of the solutions exhibited viscous behavior rather than a clear sol-gel transition in all tested concentrations. The heterogeneous nature of CEC in an aqueous solution was determined from the Cox–Merz rule due to the coexistence of single chain complexes and aggregates. In addition, the CEC aqueous solutions showed good thermal and time stability, and the transition with temperature was reversible.     

The dissolution of microcrystalline cellulose in sodium hydroxide-urea aqueous solutions

It has been reported that cellulose is better dissolved in NaOH-water when a certain amount of urea is added. In order to understand the mechanisms of this dissolution and the interactions between the components, the binary phase diagram of urea/water, the ternary urea/NaOH/water phase diagram and the influence of the addition of microcrystalline cellulose in urea/NaOH/water solutions were studied by DSC. Urea/water solutions have a simple eutectic behaviour with a eutectic compound formed by pure urea and ice (one urea per eight water moles), melting at −12.5 °C. In the urea/NaOH/water solutions, urea and NaOH do not interact, each forming their own eutectic mixtures, (NaOH + 5H₂O, 4H₂O) and (urea, 8H₂O), as found in their binary mixtures. When the amount of water is too low to form the two eutectic mixtures, NaOH is attracting water at the expense of urea. In the presence of microcrystalline cellulose, the interactions between cellulose and NaOH/water are exactly the same as without urea, and urea is not interacting with cellulose. A tentative explanation of the role of urea is to bind water, making cellulose-NaOH links more stable. Member of the European Polysaccharide Network of Excellence (EPNOE),     

Thermal analyses of organic powders made from precipitation polymerization of triallyl monomers

Organic solids have been prepared from radical-initiated activation of solutions composed of tetradecane and triallyl trimesate (TAM) monomer or triallyl phosphate (TAP) monomer using a recently developed variation of precipitation polymerization methods. The powders, which comprise fused aggregates, are shown to be rich in monomer (83–88 wt% TAM or 86–92 wt% TAP), and are believed to be formed by a combination of hydrocarbon addition and allyl group oligomerization. TAM-g-tetradecane primary particles are on the order of 500 nm in diameter, while TAP-g-tetradecane particles are on the order of 100–200 nm diameter. These products are thermochemically assessed using a combination of differential scanning calorimetry, thermogravimetry and pyrolysis combustion flow calorimetry. The phosphorus-containing TAP-g-tetradecane shows exothermic activity around 230 °C, likely due to thermal decomposition of the trialkyl phosphate moiety, and may find use in advanced materials applications.     

Rheologic Properties of a Water-Soluble Terpolymer with Vinyl Biphenyl

A water-soluble acrylamide-modified terpolymer (PAAP) with sodium 2-acrylamido-2-methylpropane sulfonate and vinyl biphenyl as the hydrophobic monomer was synthesized to obtain a polymeric thickening agent applied in middle- and low-permeability oil reservoirs. The polymer is expected to possess a low molecular weight and high solution viscosity. The steady-state consecutive shear cycles of PAAP in aqueous and brine solutions were measured, and the viscoelastic properties of PAAP solutions were investigated as a function of polymer, NaCl and sodium dodecylbenzene sulfonate (SDBS) concentrations. The aqueous PAAP solutions exhibits pseudoplastic and thixotropic behavior over the range of shear rate and shear thickening behavior at very low shear rate. The steady-state shear results show that some disrupted associating aggregates at high shear rate can be reformed during the shear reversion process and the suitable shear rate is favorable to the formation of hydrophobically associative structures in the brine solutions. Above 0.05 g⋅dL⁻¹ PAAP, aqueous PAAP solutions have predominantly elastic character over the range of angular frequency that is strengthened with increasing polymer concentration. The PAAP brine solutions exhibit predominantly elastic behavior only above 3 rad⋅s⁻¹ and a salt-thickening effect. By addition of an optimum amount of SDBS (0.5–0.8 mmol⋅L⁻¹), the complex viscosities become much higher than the dynamic viscosities, although the loss tangent values increase owing to the formation of loose associative structures.     

Aqueous polysaccharide blends based on hydroxypropyl guar gum and carboxymethyl cellulose: synergistic viscosity and thixotropic properties

Aqueous polysaccharide blends, formed from 2.5% (w/v) solution of hydroxypropyl guar gum (HPG) and 2.5% (w/v) solution of carboxymethyl cellulose (CMC) according to different blending ratios, were investigated at 20 °C in terms of their shear-dependent viscosity and thixotropic properties. The Cross viscosity equation was found to fit the shear-dependent viscosity data with reasonable accuracy. When the HPG solution with the mass fraction (f _HPG) of 0.87 was mixed, the zero shear viscosity (η _o) of the corresponding blend was found to be 168.5753 Pa s, while the η _o values of component HPG and CMC solutions were found to be 3.3859 and 98.6525 Pa s, respectively. For the aqueous HPG/CMC blends investigated, the resulting zero shear viscosity was observed to be much greater than the combined zero shear viscosity of the component polysaccharide solutions, showing a synergistic viscosity property. The quantitative determination of the hysteresis loop area, developed during viscometer tests on shear rate–shear stress reverse paths, was used to describe the thixotropic behavior. When compared with aqueous solutions of the component polysaccharides, these polysaccharide blends could afford enhanced thixotropic property. Maximum thixotropy synergism was observed for the HPG/CMC blend with the f _HPG of 0.67.