Phase composition and structure of nanocrystalline powders based on ZrO<Subscript>2</Subscript>(Y) and Al<Subscript>2</Subscript>O<Subscript>3</Subscript> obtained by plasma spray pyrolysis

It is shown that a nonequilibrium solid solution ZrO₂(3Y, Al) with tetragonal structure is formed in systems based on ZrO₂(3Y) with Al₂O₃ as a second component. A delay in the γ → α Al₂O₃ transformation and a reduction in the size of the coherently scattering domain of modifications are observed in systems based on Al₂O₃ with ZrO₂(Y) as a second component.     

The transport and thermal properties of glassy LiPO<Subscript>3</Subscript>/crystalline Al<Subscript>2</Subscript>O<Subscript>3</Subscript> (ZrO<Subscript>2</Subscript>) composite electrolytes

Glassy LiPO₃/crystalline Al₂O₃ and glassy LiPO₃/crystalline ZrO₂ (0–12.5 vol.% of oxide fillers) composite solid electrolytes have been prepared by glass matrix softening. Their thermal and transport properties have been investigated by differential scanning calorimetry (DSC) and impedance spectroscopy methods. The addition of ZrO₂ leads to a decrease in the crystallization temperature of LiPO₃ glass. It was found that the conductivity behavior depends on the nature of the dispersed addition. In the case of the Al₂O₃ addition, the increase in the electrical conductivity is observed. The ionic conductivity of the LiPO₃/10% Al₂O₃ composite reaches 5.8 × 10^?8 S/cm at room temperature. In contrast, the conductivity in the LiPO₃/ZrO₂ composite system decreases.     

Electrical properties of Na<Subscript>2</Subscript>SO<Subscript>4</Subscript>-based composite systems

Composite electrolytes are well-known multiphase systems and exhibit maxima in the conductivity at certain second-phase concentration. An attempt has been made to investigate a number of sodium sulfate (Na₂SO₄)-based composite systems. The dispersoids that have been used are MgO, Al₂O₃, and SiO₂. The samples have been characterized using impedance spectroscopy, X-ray diffraction, and differential scanning calorimetry. The maximum conductivity has been observed for MgO dispersed system, and the percolation threshold has been observed at 30-mol% dispersoid, MgO concentration. Interestingly, two maxima have been observed in case of the Na₂SO₄–SiO₂ and Na₂SO₄–Al₂O₃ composite systems. In the Na₂SO₄–SiO₂ system, the first maximum occurs at lower concentration, i.e., in the range between 10 and 20 mol%, whereas the second occurs at the 40-mol% dispersoid concentration. For the Na₂SO₄–Al₂O₃ system, although slightly indistinguishable, two peaks in the conductivity vs composition plot have been observed around 12- and 30-mol% Al₂O₃ concentrations.     

Magnetic properties of LiNi<Subscript>0.5</Subscript>Mn<Subscript>0.47</Subscript>Al<Subscript>0.03</Subscript>O<Subscript>2</Subscript> as positive electrode for Li-ion batteries

The layered LiNi_0.5Mn_0.47Al_0.03O₂ was synthesized by wet chemical method and characterized by X-ray diffraction and analysis of magnetic measurements. The powders adopted the α-NaFeO₂ structure. This substitution of Al for Mn promotes the formation of Li(Ni_0.47²⁺Ni_0.03³⁺Mn_0.47⁴⁺Al_0.03³⁺)O₂ structures and induces an increase in the average oxidation state of Ni, thereby leading to the shrinkage of the lattice unit cell. The concentration of antisite defects in which Ni²⁺ occupies the (3a) Li lattice sites in the Wyckoff notation has been estimated from the ferromagnetic Ni²⁺(3a)–Mn⁴⁺(3b) pairing observed below 140 K. The substitution of 3% Al for Mn reduces the amount of antisite defects from 7% to 6.4–6.5%. The analysis of the magnetic properties in the paramagnetic phase in the framework of the Curie–Weiss law agrees well with the combination of Ni²⁺ (S = 1), Ni³⁺ (S = 1/2) and Mn⁴⁺ (S = 3/2) spin-only values. Delithiation has been made by the use of K₂S₂O₈. According to this process, known to be softer than the electrochemical one, the nickel ions in the (3b) sites are converted into Ni⁴⁺ in the high spin configuration, while Ni²⁺(3a)–Mn⁴⁺(3b) ferromagnetic pairs remain, as the Li⁺(3b) ions linked to the Ni²⁺(3a) ions in the antisite defects are not removed. The results show that the antisite defect is surrounded by Mn⁴⁺ ions, implying the nonuniform distribution of the cations in agreement with previous NMR and neutron experiments.     

An investigation into ultra-thin pseudobinary oxide (TiO<Subscript>2</Subscript>)<Subscript>x</Subscript>(Al<Subscript>2</Subscript>O<Subscript>3</Subscript>)<Subscript>1-x</Subscript> films as high-<Emphasis Type="Italic">k</Emphasis> gate dielectrics

As potential gate dielectric materials, pseudobinary oxide (TiO₂)_x(Al₂O₃)_1-x (0.1≤x≤0.6) films (TAO) were deposited on Si (100) substrates by pulsed-laser deposition method and studied systematically via various measurements. By a special deposition process, including two separate steps, the TAO films were deposited in the form of two layers. The first layer was deposited at room temperature and the second layer was completed at the substrate temperature of 400 °C. Detailed data show that the properties of the TAO films are closely related to the ratio between TiO₂ and Al₂O₃. The existence of the first layer deposited at room temperature can effectively restrain the formation of the interfacial layer. And according to the results of X-ray photoelectron spectroscopy and high-resolution transmission electron microscopy performed on the films, no other information belonging to the silicon oxide could be observed. For the (TiO₂)_0.4(Al₂O₃)_0.6 film, the best result has been achieved among all samples and its dielectric constant is evaluated to be about 38. It is valuable for the amorphous TAO film as one of the promising dielectric materials for high-k gate dielectric applications. PACS 77.55.+f; 73.40.Qv; 81.15.Fg     

Metallic liquid hydrogen and likely Al<Subscript>2</Subscript>O<Subscript>3</Subscript> metallic glass

Dynamic compression has been used to synthesize liquid metallic hydrogen at 140 GPa (1.4 million bar) and experimental data and theory predict Al₂O₃ might be a metallic glass at ∼ 300 GPa. The mechanism of metallization in both cases is probably a Mott-like transition. The strength of sapphire causes shock dissipation to be split differently in the strong solid and soft fluid. Once the 4.5-eV H-H and Al-O bonds are broken at sufficiently high pressures in liquid H₂ and in sapphire (single-crystal Al₂O₃), electrons are delocalized, which leads to formation of energy bands in fluid H and probably in amorphous Al₂O₃. The high strength of sapphire causes shock dissipation to be absorbed primarily in entropy up to ∼400 GPa, which also causes the 300-K isotherm and Hugoniot to be virtually coincident in this pressure range. Above ∼400 GPa shock dissipation must go primarily into temperature, which is observed experimentally as a rapid increase in shock pressure above ∼400 GPa. The metallization of glassy Al₂O₃, if verified, is expected to be general in strong oxide insulators. Implications for Super Earths are discussed.     

Evolution of MgAl<Subscript>2</Subscript>O<Subscript>4</Subscript> crystals in Al-Mg-SiO<Subscript>2</Subscript> composites

The present study analyzes the morphological transformations of reaction products i.e., MgO, MgAl₂O₄ occurring during the reaction between SiO₂ and Al-Mg alloy in Al-Mg-SiO₂ composite processed by the liquid metallurgy technique. Different phases of platelet and hexagonal morphologies are detected and their composition analysis by EDS has confirmed them as being transition phases existing between MgO, MgAl₂O₄ and Al₂O₃. This study has also revealed the gradual transformation of (i) MgO needles to octahedral MgAl₂O₄ through Mg-Al-Si-O and Mg-Al-O transition phases having platelet morphologies and (ii) MgAl₂O₄ to Al₂O₃ through hexagonal transition phases on holding of Al-5Mg-SiO₂ and Al-1Mg-SiO₂ composites respectively at 1023K. Fully developed α-Al₂O₃ crystals are not observed under the present experimental conditions, wherein the Mg content is well above the equilibrium Mg content required for the formation of stable Al₂O₃ (<0.05 wt. %). PACS 05.70.Np     

Methane sensor based on SnO<Subscript>2</Subscript>/In<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> nanostructure

Two sets of samples of SnO₂/In₂O₃/TiO₂ system have been fabricated with different concentrations of component materials. In the first set TiO₂ with rutile structure was used, while in the second set it has the structure of anatase. Thin films (up to 50 nm) of obtained mixtures were deposited. Their sensitivity and selectivity with respect to methane (CH4) were studied. Nanostructure on the basis of 70%SnO₂ — 10%In₂O₃ — 20%TiO₂(anatase) exhibits sufficient sensitivity to methane.     

Laser performance of holmium-doped Lu<Subscript>3</Subscript>Al<Subscript>5</Subscript>O<Subscript>12</Subscript> and (Lu,Y)<Subscript>3</Subscript>Al<Subscript>5</Subscript>O<Subscript>12</Subscript> crystals pumped by Tm:fiber laser

Optical properties of Ho³⁺-doped Lu₃Al₅O₁₂ and (Lu,Y)₃Al₅O₁₂ crystals were investigated and compared. Substitution of Y for Lu in the host garnet Lu₃Al₅O₁₂ results in broad absorption and emission spectra, and improvements in the laser behavior of Ho³⁺. Pumped by Tm:fiber laser, a maximum output power of 5.02 and 5.73 W of Ho-doped Lu₃Al₅O₁₂ and (Lu,Y)₃Al₅O₁₂ have been obtained, respectively. The center lasing wavelength are 2124.5 and 2123.0 nm for Lu₃Al₅O₁₂ and (Lu,Y)₃Al₅O₁₂, respectively.     

Investigation on structural characteristics of PVDF–AgCF<Subscript>3</Subscript>SO<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanocomposite solid polymer electrolyte system

There has been an increasing interest towards the incorporation of nanosize ceramic fillers in polymer electrolytes. Solid polymer electrolytes based on polyvinylidene fluoride (PVDF), silver triflate (AgCF₃SO₃), and x wt% of aluminum oxide (Al₂O₃) nanopowders (where x = 1, 3, 5, and 10, respectively) have been prepared using solution casting technique. The structural characteristics of these thin film specimens were studied using Fourier transform infrared (FTIR) and X-ray diffraction (XRD) patterns at room temperature. The appearance of new absorption bands and gradual shifts observed in some characteristic peaks confirmed the complex formation between polyvinylidene fluoride and silver triflate. Furthermore, the addition of nanosized filler Al₂O₃ has also indicated the interaction of the filler with the polymer salt complex. The XRD patterns obtained for all these samples in the 2θ range 10° to 70° showed the amorphous nature of these samples. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, December 7–9, 2006.     

UV-protection properties of electrospun polyacrylonitrile nanofibrous mats embedded with MgO and Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles

This article describes the ultraviolet (UV) protection of MgO and Al₂O₃ nanoparticles embedded electrospun polyacrylonitrile (PAN) nanofibrous mats. UV radiation is a harmful part of sunlight and prolonged exposure to it can cause serious skin damages. In this research, nanofibrous mats consisting of nanofibers with different diameters containing different amounts of MgO, Al₂O₃, MgO Plus, and Al₂O₃ Plus nanoparticles were produced, and their UV-protection was measured. The specific surface area of MgO, MgO Plus, Al₂O₃, and Al₂O₃ Plus nanoparticles was 230, 600, 275, and 550 m²/g, respectively. The mean diameter of electrospun PAN nanofibers embedded with metal oxide nanoparticles was in the range of 665–337 nm. The results showed that the UV-protection (shielding) capability of the mats strongly depends on fiber diameter; in fact a thin mat of nanofibers has a much stronger UV-protection in comparison to a thicker mat composed of regular fibers. UV transmission is reduced as a result of embedding MgO and Al₂O₃ nanoparticles in the electrospun PAN nanofibrous mats. MgO Plus and Al₂O₃ Plus show higher UV-protection than MgO and Al₂O₃.     

Effect of sintering conditions on the properties of sol-gel-derived Li<Subscript>1.3</Subscript>Al<Subscript>0.3</Subscript>Ti<Subscript>1.7</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>

Solid electrolyte Li_1.3Al_0.3Ti_1.7(PO₄)₃ was prepared by sol-gel method under different sintering conditions. The structural identification, surface morphology, electrochemical window, ionic conductivity, and activation energy of the Li_1.3Al_0.3Ti_1.7(PO₄)₃ sintered pellets were investigated by X-ray diffraction, scanning electron microscopy, cyclic voltammetry, and electrochemical impedance spectroscopy. It is found that the sintering temperature and time have considerable effect on the properties of the Li_1.3Al_0.3Ti_1.7(PO₄)₃ sintered pellets. The Li_1.3Al_0.3Ti_1.7(PO₄)₃ pellet sintered at 900 °C for 2 h is denser than the pellets sintered at other conditions. Different sintering conditions result in the sintered pellet with different porosity. However, the sintering conditions have little effect on the electrochemical window of Li_1.3Al_0.3Ti_1.7(PO₄)₃. Among the Li_1.3Al_0.3Ti_1.7(PO₄)₃ pellets sintered at various conditions, the pellet sintered at 900 °C for 2 h shows the highest ionic conductivity of 3.46 × 10⁻⁴ S cm⁻¹ and the lowest activation energy of 0.2821 eV.     

Transport characteristics of phonons and the specific heat of Y<Subscript>2</Subscript>O<Subscript>3</Subscript>:ZrO<Subscript>2</Subscript> solid solution single crystals

The temperature dependences of the specific heat and transport characteristics of phonons in single crystals of yttrium-stabilized zirconium dioxide Y₂O₃:ZrO₂ solid solutions have been studied. It has been shown that the temperature dependences of the specific heat at T > 5 K are almost identical at the degree of stabilization of a solid solution with an Y₂O₃ content of 5–20 mol %. Differences in the temperature dependences of the specific heat of samples from different sources at T < 5 K are due to the presence of low-energy two-level systems. The features of the transport characteristics of thermal phonons at liquid helium temperatures reflect not only the presence of two-level systems but also the scattering of phonons on low-dimensional domains of another phase coherently conjugate to the main phase of the Y₂O₃:ZrO₂ solid solution.     

Cells studies on PEO/PEG/NaClO<Subscript>3</Subscript> thin-film electrolyte system based on composite V<Subscript>2</Subscript>O<Subscript>5</Subscript> electrode

The thin-film solid polymer electrolyte based on polyethylene oxide (PEO) with sodium chlorite (NaClO₃) has been prepared by a solution-cast technique. The electrolyte was characterized by X-ray diffraction (XRD), infrared (IR), cyclic voltammetry, alternating current conductivity, and Wagner’s polarization studies. The complexation of NaClO₃ with PEO was confirmed through the XRD and IR studies. The transference number measurement has shown that the ion transport is predominant over electrons in the polymer electrolytes (t _ions ≈ 0.94). The conductivity enhancement was observed in the case of the PEO/NaClO₃ system with the addition of plasticizers (low-molecular-weight polyethylene glycol, organic solvents propylene carbonate and dimethyl formamide. Cyclic voltammetry analysis showed the stability and redox character of the electrolyte and electrode. Finally, polymer electrolyte systems were examined by electrochemical cell studies using V₂O₅ and composite V₂O₅ cathode at temperature of 35 °C. Overall, the plasticized electrolyte shows a better electrochemical performance, and a higher discharge capacity was observed in composite V₂O₅-based cells over V₂O₅-based cells.     

RETRACTED ARTICLE: Refractive-index tailoring and morphological evolutions in Gd<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript> and ZrO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> composite thin films

Refractive-index tailoring and morphological evolutions in two different thin film composite systems of gadolinia–silica (Gd₂O₃:SiO₂) and zirconia–silica (ZrO₂:SiO₂) deposited through reactive electron-beam codeposition processes are discussed in this research paper. For Gd₂O₃:SiO₂ the refractive-index tuning has been achieved from 1.45 to 2.18, whereas in the case of ZrO₂:SiO₂ the achieved tunable range is from 1.45 to 2.45 in the ultraviolet region. Under certain compositional mixings with lower silica fractions both the systems demonstrated relative microstructural and morphological densifications. Such evolutions were very successfully derived through phase-modulated ellipsometry and atomic force microscopy. The composition-dependent refractive-index tailoring and microstructural densifications have been investigated by adopting Tauc–Lorentz and single-effective-oscillator models. The morphological correlation functions have also very aptly supported such evolutions in these composite films. These experimental results indicate their favourable properties and applicability down to the extreme ultraviolet wavelength region of the electromagnetic spectrum. PACS 42.79.Wc; 78.66.-w; 78.20.Ci; 61.16.Ch; 42.70.-a;68.55.-a; 68.35.Bs; 81.15.Ef     

Effect of porosity and pore morphology on the low-frequency dielectric response in sintered ZrO<Subscript>2</Subscript>—8 mol% Y<Subscript>2</Subscript>O<Subscript>3</Subscript> ceramic compact

Effect of porosity and pore size distribution on the low-frequency dielectric response, in the range 0.01–100 kHz, in sintered ZrO₂—8 mol% Y₂O₃ ceramic compacts have been investigated. Small-angle neutron scattering (SANS) technique has been employed to obtain the pore characteristics like pore size distribution, specific surface area etc. It has been observed that the real and the imaginary parts of the complex dielectric permittivity, for the specimens, depend not only on the porosity but also on the pore size distribution and pore morphology significantly. Unlike normal Debye relaxation process, where the loss tangent vis-à-vis the imaginary part of the dielectric constant shows a pronounced peak, in the present case the same increases at lower frequency region and an anomalous non-Debye type relaxation process manifests.     

Investigation of ion transport in Li<Subscript>8</Subscript>ZrO<Subscript>6</Subscript> and Li<Subscript>6</Subscript>Zr<Subscript>2</Subscript>O<Subscript>7</Subscript> solid electrolytes

Lithium ionic conductivity and spin-lattice relaxation rates were measured in Li₈ZrO₆ and Li₆Zr₂O₇ solid electrolytes. It was found that the Li₈ZrO₆ solid electrolyte undergoes a transition to the superionic state in the temperature range 673–703 K. It was shown that Li⁺ ions are mobile in particular lattice positions of the Li₆Zr₂O₇ phase, and that ionic conductivity is monotonic at an activation energy of 79.4 kJ/mol.     

Up-conversion emissions of Er<Superscript>3+</Superscript>-Yb<Superscript>3+</Superscript> codoped Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles by the arc discharge synthesis method

The Er³⁺-Yb³⁺ codoped Al₂O₃ nanoparticles with an average particle size of about 50 nm have been synthesized by an arc discharge synthesis method. The green and red up-conversion emissions centered at about 526, 547 and 677 nm, corresponding respectively to the ²H_11/2→⁴I_15/2, ⁴S_3/2→⁴I_15/2 and ⁴F_9/2→⁴I_15/2 transitions of Er³⁺, were detected by a 978-nm semiconductor laser diode excitation. The Annealing has evident effect on the up-conversion emissions of the samples: The red up-conversion emission is noticeable before annealing; however, the green up-conversion emission becomes predominant after annealing. The mixture of (Er,Yb)₃Al₅O₁₂ and α-(Al,Er,Yb)₂O₃ phases is more favorable for green up-conversion emissions due to an enhancement of the ESA (I) of ⁴I_11/2+a photon→⁴F_7/2 and ET (III) of ²F_5/2(Yb³⁺)+⁴I_11/2(Er³⁺)→²F_7/2(Yb³⁺)+⁴F_7/2(Er³⁺) processes. The two-photon absorption up-conversion process is involved in the green and red up-conversion emissions. The results have proved that arc discharge synthesis is a new promising preparation technology for optical materials. Supported by National Natural Science Foundation of China (Grant No. 10804015), the Scientific Research Foundation for Doctor of Liaoning Province (Grant No. 20071095), and the Educational Committee Foundation of Liaoning Province (Grant No. 2008123)     

Ion conduction and space-charge polarization processes in Li<Subscript>2</Subscript>Ge<Subscript>7</Subscript>O<Subscript>15</Subscript> crystals

The electrical properties of a lithium heptagermanate (Li₂Ge₇O₁₅) crystal have been studied in DC and AC measuring fields at temperatures from 500 to 700 K. In a DC field, a substantial decrease of electrical conductivity σ with time has been detected. On the basis of kinetic dependences σ(t), estimates of the charge carrier diffusion coefficient D have been obtained. In the frequency range 10¹–10⁵ Hz, the spectra of complex impedance ρ*(f) have been measured. The analysis of diagrams in the complex plane (ρ″–ρ′) has been performed within the equivalent circuit approach. It has been shown that, in the considered temperature and frequency intervals, the electrical properties of Li₂Ge₇O₁₅ crystals have been determined by the hopping conduction of interstitial lithium ions A _Li and accumulation of charge carriers near the blocking Pt electrodes.     

Synthesis and magnetic properties of FeNi<Subscript>3</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> core-shell nanocomposites

In this study, FeNi₃/Al₂O₃ core-shell nanocomposites, where individual FeNi₃ nanoparticles were coated with a thin layer of alumina, were fabricated by a modified sol-gel method. Several physical characterizations were performed on the samples of FeNi₃/Al₂O₃ nanocomposites with different thickness of Al₂O₃ shell. The encapsulation of FeNi₃ nanoparticles with alumina stops FeNi₃ agglomeration during heat treatment, and prevents interaction among the closely spaced magnetic FeNi₃ nanoparticles. The Al₂O₃ insulating shell improves the soft magnetic properties of FeNi₃. The study of the complex permeability of the samples shows that the real part μ’ of the permeability of the sample with Al molar content of 20% (Al/(Fe+Ni)) is as high as 12, and independent of frequency up to at least 1 GHz. The tunneling magnetoresistance arising from the presence of the Al₂O₃ shell have also been studied.