Conducting polymer film-based immunosensors using carbon nanotube/antibodies doped polypyrrole

Carbon nanotube/polypyrrole/antibodies polymer films were synthesized successfully on microelectrodes by electrochemical deposition. Electropolymerization was performed at optimal range between −0.8 and +0.8 V at a scan rate of 50 mV s⁻¹ in an electrochemical mini-cell containing monomer pyrroles, carbon nanotubes, and goat IgGs. The conducting polymer films were characterized by Fourier transform infrared spectrometry, Raman spectra, and Field emission scanning electron microscopy. And then, it was prepared for immunosensor application to determine anti-goat IgGs. The results show that a linear range between 0.05 and 0.7 μg ml⁻¹ for anti-goat IgGs detection was observed for immunosensor, a detection limit as low as 0.05 μg ml⁻¹ and a response time of 1 min. The effect parameters of electropolymerization process on immunosensor response are also studied. It found that the immunosensor well active in 1.5 mg ml⁻¹ CNT concentration, 2.5 mM pyrrole, 10 μg ml⁻¹ goat IgGs.     

Influence of filler alignment in the mechanical and electrical properties of carbon nanotubes/epoxy nanocomposites

In this work, we report the mechanical and electrical properties of carbon nanotubes/epoxy composites prepared with aligned and randomly oriented nanotubes as filler. The samples are disks of 30 mm in diameter and 3 mm in thickness. To obtain the carbon nanotubes alignment, an external electric field (250 VAC; 50 Hz) was applied through the thickness of the sample during all the cure process. The AC electrical current was measured, during the cure, as a strategy to determine the optimum time in which the alignment reaches the maximum value. DC conductivity measured after the cure shows a percolation threshold in the filler content one order of magnitude smaller for composites with aligned nanotubes than for composites with randomly oriented filler (from 0.06 to 0.5 wt%). In the percolation threshold, the achieved conductivity was 1.4×10⁻⁵ Sm⁻¹. In both cases, aligned and randomly distributed carbon nanotube composites, the wear resistance increases with the addition of the filler while the Rockwell hardness decreases independently of the nanotubes alignment.     

Fabrication and structure: a study of aligned carbon nanotube/carbon nanocomposites

Aligned carbon nanotube/carbon (Acnt/C) nanocomposites have been fabricated by densifying an Acnt preform with chemical vapour infiltration technology. Microstructure observations show that pyrocarbon in Acnt/C was mainly rough lamella type while pyrocarbon in carbon fiber reinforced carbon matrix (C/C) composites was typically smooth lamella type in spite of the same process. The thermal conductivity of these Acnt/C nanocomposites is about 4 times that of C/C composites. Their electrical conductivity of Acnt/C nanocomposites was anisotropic, i.e. approximately 1.61×10⁴ Ω⁻¹ m⁻¹ and 5.68×10³ Ω⁻¹ m⁻¹ in the direction parallel and vertical to the aligned carbon nanotubes, respectively.     

Electrical transport characteristic of carbon nanotube after mass-separated ultra-low-energy oxygen ion beams irradiation

Mass-separated ultra-low-energy oxygen ion beams were irradiated to the single-walled carbon nanotubes (SWCNTs) under an ultra-high-vacuum pressure of 10⁻⁷ Pa for the purpose of achieving n-type conduction of nanotubes. The ion beam energy was 25 eV, which was close to the displacement energy of graphite. The incident angle of the ion beam was normal to the target nanotube. The ion dose ranged from 3.3 × 10¹¹ to 3.8 × 10¹² ions/cm². The structure of SWCNTs after the ion irradiation was investigated. The CNTs still have a clear single-walled structure after the ion irradiation. The graphite structure is distorted and some defects are induced in the nanotube by the oxygen irradiation. The oxygen ions with the ion energy of 25 eV are irradiated to the field effect transistor (FET) device with the nanotube channel. The n-type characteristic appears upon the oxygen ion irradiation, and the device exhibits ambipolar behavior. The defects induced by the ion irradiation may act as the n-type dopants.     

High-field electron emission of carbon nanotubes grown on carbon fibers

Carbon nanotubes with uniform density were synthesized on carbon fiber substrate by the floating catalyst method. The morphology and microstructure were characterized by scanning electron microscopy and Raman spectroscopy. The results of field emission showed that the emission current density of carbon nanotubes/carbon fibers was 10 μA/cm² and 1 mA/cm² at the field of 1.25 and 2.25 V/μm, respectively, and the emission current density could be 10 and 81.2 mA/cm² with the field of 4.5 and 7 V/μm, respectively. Using uniform and sparse density distribution of carbon nanotubes on carbon fiber substrate, the tip predominance of carbon nanotubes can be exerted, and simultaneously the effect of screening between adjacent carbon nanotubes on field emission performance can also be effectively decreased. Therefore, the carbon nanotubes/carbon fibers composite should be a good candidate for a cold cathode material.     

Selective growth of carbon nantoubes on SiO2/Si substrate

Three-step raising temperature process was employed to fabricate carbon nanotubes by pyrolysis of ferrocene/melamine mixtures on silica and single crystalline silicon wafers respectively. Then the morphologies, structures and compositions of obtained carbon nanotubes are investigated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive X-ray spectroscope (EDX) and electron energy-loss spectroscopy (EELS). TEM and SEM observation shows that on silica substrate, high-oriented carbon nanotube can grow compactly to form continuous film on both frontal and cross-section surfaces, but on silicon substrate, only can form on cross-section surface. These carbon nanotubes have much irregular cup-like structure, and with outer diameter varying from 25 nm to 35 nm. At the top end of carbon nanotube there is a catalyst particle. EDX analysis reveals that the particle are iron cluster, and EELS spectrum indicates that the nanotube is composed of pure carbon. Finally, the effect of substrate surface roughness on the growth behavior of carbon nanotubes has been discussed.     

NMR strategies to study the local magnetic properties of carbon nanotubes

The local magnetic properties of the one dimensional inner space of the nanotubes are investigated using ¹³C nuclear magnetic resonance spectroscopy of encapsulated fullerene molecules inside single walled carbon nanotubes. Isotope engineering and magnetically purified nanotubes have been advantageously used on our study to discriminate between the different diamagnetic and paramagnetic shifts of the resonances. Ring currents originating from the π electrons circulating on the nanotube, are found to actively screen the applied magnetic field by −36.9 ppm. Defects and holes in the nanotube walls cancel this screening locally. What is interesting, that at high magnetic fields, the modifications of the NMR resonances of the molecules from free to encapsulated can be exploited to determine some structural characteristics of the surrounding nanotubes, never observed experimentally.     

Synthesis, characterization and cytotoxicity of surface amino-functionalized water-dispersible multi-walled carbon nanotubes

Surface functionalization of multi-walled carbon nanotubes (MWCNTs), with amino groups via chemical modification of carboxyl groups introduced on the nanotube surface, using O-(7-azabenzotriazol-1-yl)-N,N,N′,N′-tetramethyluronium hexafluorophosphate (N-HATU) and N,N-diisopropylethylamine (DIEA) is reported. The N-HATU coupling agent provides faster reaction rate and the reaction occurs at lower temperature compared to amidation and acylation-amidation chemistry. The amines, 1,6-hexanediamine (HDA), diethylenetriamine (DETA), triethylenetetramine (TETA) and 1,4-phenylenediamine (PDA) were used. The resulting materials were characterized with different techniques such as FTIR, XRD, elemental analysis, TGA, TEM, UV-vis spectroscopy and cyclic voltammetry. MWCNTs functionalized with PDA posses the best dispersibility and electron transfer properties in comparison to the others amines. Functionalized MWCNTs, at the concentrations between 1 and 50 μg ml⁻¹, were not cytotoxic for the fibroblast L929 cell line. However, the concentrations of MWCNTs higher of 10 μg ml⁻¹ reduced cell growth and this effect correlated positively with the degree of their uptake by L929 cells.     

Morphology, mechanical, cross-linking, thermal, and tribological properties of nitrile and hydrogenated nitrile rubber/multi-walled carbon nanotubes composites prepared by melt compounding: The effect of acrylonitrile content and hydrogenation

The purpose of this work was to prepare nanocomposites by mixing multi-walled carbon nanotubes (MWCNT) with nitrile and hydrogenated nitrile elastomers (NBR and HNBR). Utilization of transmission electronic microscopy (TEM), scanning electron microscopy (SEM), and small- and wide-angle X-ray scattering techniques (SAXS and WAXS) for advanced morphology observation of conducting filler-reinforced nitrile and hydrogenated nitrile rubber composites is reported. Principal results were increases in hardness (maximally 97 Shore, type A), elastic modulus (maximally 981 MPa), tensile strength (maximally 27.7 MPa), elongation at break (maximally 216%), cross-link density (maximally 7.94 × 10²⁸ m⁻³), density (maximally 1.16 g cm⁻³), and tear strength (11.2 kN m⁻¹), which were clearly visible at particular acrylonitrile contents both for unhydrogenated and hydrogenated polymers due to enhanced distribution of carbon nanotubes (CNT) and their aggregated particles in the applied rubber matrix. Conclusion was that multi-walled carbon nanotubes improved the performance of nitrile and hydrogenated nitrile rubber nanocomposites prepared by melt compounding.     

Electron field emission properties of conducting polymer coated multi walled carbon nanotubes

The present work describes the field emission characteristics of conducting polymer coated multi walled carbon nanotubes (MWNTs) field emitters fabricated over flexible graphitized carbon cloth. Nanocomposites involving the combination of MWNTs and conducting polymers polyaniline (PANI) and polypyrrole (PPy) have been prepared by in-situ polymerization method and have been characterized using scanning electron microscopy and transmission electron microscopy. Using spin coating method, field emitters based on PANI/MWNTs and PPy/MWNTs over flexible graphitized carbon cloth have been prepared. The field emission characteristics have been studied using an indigenously fabricated set up in a vacuum chamber with a base pressure of 2 × 10⁻⁵ Pa and the results are discussed. Our results display that the field emission performance of the emitters depends strongly on the work function of the emitting material. Low turn on emission field of 2.12 V/μm at 10 μA/cm² and high emission current density of 1 mA/cm² at 3.04 V/μm have been observed for PANI/MWNTs field emitter.     

Third-order nonlinear optical properties of multiwalled carbon nanotubes modified by CdS nanoparticles

CdS nanoparticles were coated on the side wall of multiwalled carbon nanotubes (MWCNTs) by a wet chemical synthesis approach via noncovalent functionalization of MWCNTs with poly(diallyldimethylammonium chloride) (PDDA). The as-prepared material was characterized by X-ray diffraction (XRD), UV–vis absorption, fluorescence and transmission electron microscopy (TEM). The results indicated that CdS nanoparticles were uniformly coated on the surface of MWCNTs. Third-order optical nonlinearity of the as-prepared material was studied with the Z-scan technique with picosecond laser pulses at 532 nm. The Z-scan curve revealed that CdS nanoparticle-modified MWCNTs exhibited negative nonlinear refraction index and positive absorption coefficient. The real part and imaginary part of the third-order nonlinear susceptibility χ⁽³⁾ were calculated to be −4.9 × 10⁻¹² and 6.8 × 10⁻¹³ esu, respectively.     

Production and characterization of polymer nanocomposite with aligned single wall carbon nanotubes

We reported a simple method to fabricate polymer nanocomposites with single-walled carbon nanotubes (SWNTs) having exceptional alignment and improved mechanical properties. The composite films were fabricated by casting a suspension of single walled carbon nanotubes in a solution of thermoplastic polyurethane and tetrahydrofuran. The orientation as well as dispersion of nanotubes was determined by scanning electron microscopy, transmission electron microscopy and polarized Raman spectroscopy. The macroscopic alignment probably results from solvent-polymer interaction induced orientation of soft segment chain during swelling and moisture curing. The tensile behavior of the aligned nanotube composite film was also studied. At a 0.5 wt.% nanotube loading, a 1.9-fold increase in Young's modulus was achieved.     

Fabrication and characterization of suspended single-walled carbon nanotubes

Suspended single-walled carbon nanotubes (SWCNTs) between SiO₂ pillars via a direct lithographic route using a simple mixture of catalyst precursor [Co(III) acetylacetonate, Co(acac)₃] and conventional electron beam resist (ma-N2403) were fabricated. The catalytic electron beam resist (Cat-ER) layer plays dual roles as a catalyst and a resist layer for the growth and alignment of CNTs, respectively. The structure of the grown nanotube was characterized by Raman spectroscopy (633 nm laser excitation). Nanotubes grown from Cat-ER with Co(acac)₃ show the typical Raman spectra of SWCNTs which are characterized by the strong tangential bands near to 1590 cm⁻¹ and radial breathing modes (RBMs) in the low frequency region (<300 cm⁻¹). The calculated diameter of the probed nanotubes individually corresponds to the range 0.86-1.77 nm.     

Transmission electron microscopy observations of CNT morphology before and after heating in vacuum

Heating of multi-walled carbon nanotubes is often required to obtain clean patterns in the field electron emission microscope (FEEM). A transmission electron micrograph study of morphological changes in the cap structure of multi-walled carbon nanotubes due to heating in vacuum is presented. The lack of significant structural change in the cap structure when specimens were heated to 1925 K for 2.5 h determines an upper bound for the diffusivity of multi-walled carbon nanotube surface atoms, of the order of 10⁻¹⁶ cm²/s at 1925 K.     

Complex and new modification techniques of thiocholine detection electrodes with carbon nanotubes

A new and complex modification technique of glassy carbon electrode (GCE) with multi-walled carbon nanotubes (MWNTs) was developed. Firstly, MWNTs were electro-deposited on GCE at 1.70 V for 2 h. Secondly, by layer-by-layer (LBL) self-assembly technique, a functional membrane of {PDDA/MWNTs}_n were fabricated by alternative immersion in 1% PDDA solution and 1 mg L⁻¹ MWNTs dispersion either. As a result, the modified membrane with five {PDDA/MWNTs} bilayers have good sensitivity, stability, anti-fouling ability and catalytic activity for thiocholine (TCh) detection, the oxidation potential on the modified GCE was decreased almost by 50% while the peak current was increased almost by 100% compared with that on bare GCE. Meanwhile, it showed a low detection limit of less than 7.500 × 10⁻⁷ mol L⁻¹ TCh.     

Improving the surface properties of multi-walled carbon nanotubes after irradiation with gamma rays

The effects of gamma-irradiation on the modification of the surface and structure of multi-walled carbon nanotubes were studied. Gamma-irradiation affected the graphitization properties of functional groups, and decreased the diameter of multi-walled carbon nanotubes. The irradiated multi-walled carbon nanotubes with the absorbed dose of 100 kGy exhibited a larger specific surface area and microporous volume as compared with the other samples. The Raman spectroscopy and X-ray photoelectron spectroscopy showed that the interaction between the gamma-irradiation and the multi-walled carbon nanotubes with the absorbed dose of 150 kGy destroyed the nanostructure of carbons, leading to the formation of diamond-like structures and carbon oxides. In addition, gamma-irradiation with the absorbed dose of 100 kGy improved multi-walled carbon nanotubes graphitization and surface properties while at higher absorbed dose (150 kGy), it induced damaged structures (sp³ bonds and oxygen compositions).     

Catalytic activity of Fe, Co and Fe-Co-MCM-41 for the growth of carbon nanotubes by chemical vapour deposition method

Iron, cobalt and a mixture of iron and cobalt incorporated mesoporous MCM-41 molecular sieves were synthesised by hydrothermal method and used to investigate the rules governing their nanotube producing activity. The catalysts were characterised by XRD and N₂ sorption studies. The effect of the catalysts has been investigated for the production of carbon nanotubes at an optimised temperature 750 °C with flow rate of N₂ and C₂H₂ is 140 and 60 ml/min, respectively for a reaction time 10 min. Fe-Co-MCM-41 catalyst was selective for carbon nanotubes with low amount of amorphous carbon with increase in single-walled carbon nanotubes (SWNTs) yield at 750 °C. Formation of nanotubes was studied using scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Raman spectroscopy. Transmission electron microscope and Raman spectrum was used to follow the quality and nature of carbon nanotubes formed and the graphitic layers and disordered band, which shows the clear evidence for the formation of SWNTs, respectively. The result propose that the diameter of the nanotubes in the range of 0.78-1.35 nm. Using our optimised conditions for this system, Fe-Co-MCM-41 showed the best results for selective SWNTs with high yield when compared with Fe-MCM-41 and Co-MCM-41.     

Hydrogen peroxide biosensor based on gold nanoparticles/thionine/gold nanoparticles/multi-walled carbon nanotubes-chitosans composite film-modified electrode

In this paper, an amperometric electrochemical biosensor for the detection of hydrogen peroxide (H₂O₂), based on gold nanoparticles (GNPs)/thionine (Thi)/GNPs/multi-walled carbon nanotubes (MWCNTs)-chitosans (Chits) composite film was developed. MWCNTs-Chits homogeneous composite was first dispersed in acetic acid solution and then the GNPs were in situ synthesized at the composite. The mixture was dripped on the glassy carbon electrode (GCE) and then the Thi was deposited by electropolymerization by Au-S or Au-N covalent bond effect and electrostatic adsorption effect as an electron transfer mediator. Finally, the mixture of GNPs and horseradish peroxidase (HRP) was assembled onto the modified electrode by covalent bond. The electrochemical behavior of the modified electrode was investigated by scanning electron microscope, cyclic voltammetry and chronoamperometry. This study introduces the in situ-synthesized GNPs on the other surface of the modified materials in H₂O₂ detection. The linear response range of the biosensor to H₂O₂ concentration was from 5 × 10⁻⁷ mol L⁻¹ to 1.5 × 10⁻³ mol L⁻¹ with a detection limit of 3.75 × 10⁻⁸ mol L⁻¹ (based on S/N = 3).     

Selective growth, characterization, and field emission performance of single-walled and few-walled carbon nanotubes by plasma enhanced chemical vapor deposition

Single-walled carbon nanotubes (SWCNTs) and few-walled carbon nanotubes (FWCNTs) have been selectively synthesized by plasma enhanced chemical vapor deposition at a relative low temperature (550 °C) by tuning the thickness of iron catalyst. The parametric study and the optimization of the nanotube growth were undertaken by varying inductive power, temperature, catalyst thickness, and plasma to substrate distance. When an iron film of 3-5 nm represented the catalyst thickness for growing FWCNT arrays, SWCNTs were synthesized by decreasing the catalyst thickness to 1 nm. The nanotubes were characterized by field emission scanning electron microscopy, transmission electron microscopy, and Raman spectroscopy. Electron field emission properties of the nanotubes indicate that the SWCNTs exhibit lower turn-on field compared to the FWCNTs, implying better field emission performance.     

Comparative study of electrochemical capacitance of multi-walled carbon nanotubes before and after chopping

In the work, short multi-walled carbon nanotubes (S-CNTs) were synthesized by chopping conventional μm-long multi-walled carbon nanotubes (L-CNTs) under ultrasonication in H₂SO₄/HNO₃ mixed acids. A comparative electrochemical investigation performed in 6 M KOH solution demonstrated that a specific capacitance (SC) of ca. 14.6 μF cm⁻² was delivered by the S-CNTs with the specific surface area (SSA) of 207 m² g⁻¹, much larger than that of ca. 10.1 μF cm⁻² for the L-CNTs with the SSA of 223 m² g⁻¹, the reason for which was that S-CNTs with two open ends, due to good ion penetrability, provided more entrances for electrolyte ions to access the inner surface easily through their shorter inner pathway so as to enhance their SSA utilization and geometric SC. The surface structure disruption of S-CNTs, owing to ultrasonication and oxidation during chopping process, deteriorated their electronic conductivity and resulted in an inferior power property in contrast to L-CNTs.