阴阳离子聚氨酯/羟基磷灰石复合微球的制备及其自组装

分别以2,2-双羟基丙酸(DMPA)和N-甲基二乙醇胺(MDEA)作扩链剂,采用自乳化法成功制备出带有正、负电荷的阳、阴离子聚氨酯/羟基磷灰石(PU/HA)微球,并考察HA的复合比例对微球形貌、理化性能的影响。在此基础上,通过微球间的静电作用力,将制备出的阴、阳离子复合微球自组装形成凝胶体系,并对其力学性能进行探究。SEM、ζ电位和激光粒度结果显示成功制备出具有一定形貌的带电微球,其中当扩链剂含量为15%(n/n)、HA含量为10%(w/w)时,微球形貌较佳且粒度分布均匀;X射线衍射、热分析结果表明,微球确为一定比例的HA与PU复合产物;自组装体系的流变学测试结果表明,微球组装后的产物呈类凝胶状态,具有较高的弹性模量,并有一定的可注射性。同时,骨髓间充质干细胞(BMSCs)可在组装材料表面粘附、铺展,生长良好。     

超声化学法制备SrF2纳米片自组装微球

通过简单的超声化学方法制备了SrF2纳米片自组装微球.合成的产物通过粉末X射线衍射仪、场发射扫描电子显微镜、透射电子显微镜进行了表征和分析.结果表明这些微球是由规则、有序的纳米片组成.而这些纳米片互相垂直连接组装成微球.研究还发现反应物的浓度.配位剂和pH值对产物的形貌和尺寸有着重要的作用.     

基于3D受限自组装构筑中空介孔氧化硅/碳复合微球

发展简单、高效、可控的方法来制备中空介孔微球是介孔材料领域的研究热点.本工作结合嵌段共聚物的三维受限自组装(3D-CSA)和自模板碳化策略,建立了一种构筑中空介孔微球的新方法 .首先,采用乳液-溶剂挥发法实现嵌段共聚物与全氟辛烷(PFO)在3D受限空间的分级组装,获得了核-壳结构微球,其中壳层由微相分离的嵌段共聚物构成.然后,在壳层的连续相选择性地复合氧化硅,既实现了无机框架的负载,又实现了对连续相聚合物链选择性交联.对复合微球进行煅烧处理后,实现了壳层连续相聚合物的选择性碳化,获得了中空介孔氧化硅/碳复合微球.本研究系统地阐述了核-壳型分级结构微球的形成机理和必备条件,研究了氧化硅前驱体添加量和嵌段共聚物分子量对中空介孔氧化硅/碳复合微球形貌的影响,为制备中空介孔微球材料提供了一种简便、可控的方法.     

交联聚膦腈中空微球的可控制备

以分散聚合法制备的聚苯乙烯微球为模板,以六氯环三膦腈、4,4’-二羟基二苯砜为共聚单体,三乙胺为缚酸剂,室温条件下制备出了聚苯乙烯／聚膦腈（核／壳）复合微球,然后用四氢呋喃处理该复合微球,得到聚膦腈中空微球。利用红外光谱、元素分析、扫描电镜及投射电镜对所制备中空微球的结构及形貌进行了表征。结果表明,所制备聚膦腈中空微球...     

常温制备形貌可控中空羟基磷灰石的研究

利用锂钙硼玻璃(LCB)微球在磷酸盐溶液中的原位转化反应,在常温下制备中空的羟基磷灰石(HA)微球,研究了玻璃微球的组分、磷酸盐浸泡液的浓度及热处理等工艺参数对微球的形貌影响。研究结果表明,常温下反应得到的产物微球为晶型较好具有中空结构的羟基磷灰石,随着玻璃微球组分中CaO含量的升高,中空微球的球壁逐渐变厚,当CaO含量达到30%时,微球变为实心结构。磷酸盐溶液浓度较低时,中空微球的球壁容易形成层状结构。     

苯乙烯/丙烯酸正丁酯/丙烯酸共聚微球的制备及其性能表征

通过乳液聚合法和无皂乳液聚合法制备了苯乙烯/丙烯酸正丁酯/丙烯酸共聚微球.讨论了乳化剂用量、引发剂用量、功能单体、软硬单体用量比等对微球粒径和形态的影响.利用扫描电子显微镜(SEM)、傅立叶变换红外光谱仪(FTIR)对微球的粒径、形貌和表面基团进行分析.红外光谱表明,实验室所制备的苯乙烯/丙烯酸正丁酯/丙烯酸共聚微球表面存在丰富的羧基.利用竖片生长法得到自组装的多层胶体微球薄膜.通过对薄膜的反射光谱测量,发现随着湿度的增加,峰位会产生3nm左右的红移.     

具有广谱紫外屏蔽性能的三元共聚物微球的制备

以醋酸乙烯酯(VA)、 马来酸酐(MA)和商品化的紫外吸收剂2-{2-羟基-5-[2-(甲基丙烯酰氧)乙基]苯基}-2H-苯并三唑(NB)为单体, 偶氮二异丁腈(AIBN)为引发剂, 通过自稳定沉淀聚合法(2SP)制备了具有广谱紫外屏蔽性能的单分散三元共聚物微球(PVMN); 研究了溶剂、 单体配比、 引发剂用量、 单体浓度、 反应温度和反应时间对共聚物微球形态和性能的影响. 研究结果表明, 体积比为7∶3的苯甲酸乙酯/正庚烷混合溶剂是2SP法合成单分散PVMN微球的理想溶剂. 随着单体配比中紫外吸收单体NB比例的增加, 引发剂用量、 单体浓度、 反应温度的提高和反应时间的延长, 微球的粒径随之增大, 进而改变了微球的紫外屏蔽性能. 本文制备的微球的粒径范围为(249±19)~(1434±213) nm, 优化得到的PVMN微球可屏蔽约90%的紫外光. 该策略还可扩展到其它可用作紫外吸收剂的乙烯基单体, 是一种制备稳定高分子紫外屏蔽剂的通用方法.     

原位聚合法制备具有温敏PNIPAM壳的核-壳结构聚合物纳米微球的研究

结合大分子自组装和原位自由基聚合方法,采用油溶性引发剂偶氮二异丁腈(AIBN),在聚(ε-已内酯)(PCL)纳米粒子表面引发聚合单体N-异丙基丙烯酰胺(NIPAM)和交联剂亚甲基双(丙烯酰胺)(MBA),制备得到了核-壳结构的PCL/PNIPAM聚合物纳米微球.系统研究了单体和交联剂用量、壳层目标交联度、初始PCL/DMF溶液的浓度及引发剂AIBN含量4个反应参数对核-壳结构PCL/PNIPAM纳米微球的PNIPAM壳层得率、微球尺寸、温敏性能及电镜形貌的影响.结果表明,在制备核-壳结构PCL/PNIPAM纳米微球的反应过程中,PCL粒子表面的聚合和水中的聚合二者之间相互竞争.适当增加引发剂AIBN的添加量,有利于制备得到核/壳比例可控的PCL/PNIPAM纳米微球;交联剂MBA较高的反应活性导致形成了非均匀交联的PNIPAM壳层.     

碳纳米管/壳聚糖复合微球的原位仿生矿化及表征

对碳纳米管(CNTs)进行酸化处理, 采用乳化交联法制备CNTs/壳聚糖(CS)复合微球, 在其表面诱导羟基磷灰石仿生合成, 研究了CNTs对复合微球仿生矿化的影响, 并与纯CS微球的仿生矿化进行了对比. 利用扫描电子显微镜(SEM)、 X射线衍射仪(XRD)、 溶胀率和含水率测试等考察了复合微球矿化前后的形貌特征、 物相结构及稳定性. 结果表明, 在相同时间下, CNTs/CS复合微球表面纳米羟基磷灰石的形成能力明显优于纯CS微球, 且形态稳定性更高. 细胞实验结果表明, 与MG63细胞共培养7 d时, 矿化复合微球细胞增殖明显.     

细乳液法制备聚硅氧烷-Ag纳米复合微球及其抗菌性

首先以苯乙烯(St)及3-甲基丙烯酰氧基三甲氧基硅烷(MPS)为反应单体,通过细乳液聚合制备表面功能化聚硅氧烷微球,然后利用该微球表面的硅羟基及硅氧烷基团对Ag+的吸附及还原作用原位制备聚硅氧烷-Ag纳米复合微球。采用透射电镜(TEM)、紫外(UV-Vis)、热重分析(TG)及X射线衍射(XRD)等对聚硅氧烷-Ag纳米复合微球的形貌和组成进行了表征。研究表明:改变MPS和硝酸银的用量可调控聚硅氧烷-Ag纳米复合微球的形貌及表面银含量;抗菌实验结果表明,聚硅氧烷-Ag纳米复合微球具有较好的抑菌性。     

聚氨酯与铁电陶瓷粉复合物的电致感应性能研究

利用双辊制备了一系列热塑性弹性体聚氨酯（PU）和铁电钛酸锆酸铅盐（PZT）的电感应PZT／PU复合物。X－衍射和SE镜结果显示,复合物中,在铁电相中PZT陶瓷粉呈现结晶态并且均匀分布在PU基体中,复合物的弹性模量和相对电容率随着复合物中PZT体积分数增加而升高,在高压电场下,低PZT含量的复合物呈现负的电致伸缩应力,当PZT体积分数增加到6％以上时,在某个临界电场下,复合物呈现出电致伸缩应力反转的特性,即电致伸缩应力从负转变为正,并且发生应力反转的临界电场随着复合物中PZT体积分数的增加而降低,PU的电致伸缩特性与PZT在高电场下极化反转效应结合,导致了PZT／PU复合物这种有趣的性能,因此PZT／PU复合物将在高电压场方面作为传感器开关材料得到广泛应用。     

聚醚聚氨酯/环氧树脂互穿网络高聚物的研究(Ⅰ)

互穿网络高聚物(IPN)是两种或多种交联聚合物的共混体。由于两种聚合物网络相互贯穿和缠结,链节间的永久锁结产生强迫互容,使不同聚合物达到最紧密混合,最大限度地控制多相体系的相分离,IPN材料显示不寻常的耐热,耐溶剂和高强度等特点,远远超过其聚合物本身的性能。在IPN中,两网络相互贯穿程度越高,相分离越低,这主要取决于构成聚合物本身的相容性和最终网络结合方式。本文通过改变组     

Preparation of P(MBA‐co‐MAA)/Zr(OH)4/P(EGDMA‐co‐MAA)/TiO2 Tetra‐layer Hybrid Microspheres and the Corresponding ZrO2/TiO2 Double‐shelled Hollow Microspheres

Double‐shelled zirconia/titania (ZrO₂/TiO₂) hollow microspheres were prepared by the selective removal of the polymer components via the calcination of the corresponding tetra‐layer poly(N,N′‐methylenebisacryl amide‐co‐methacrylic acid) (P(MBA‐co‐MAA))/Zr(OH)₄/poly(ethyleneglycol dimethacrylate‐co‐methacrylic acid) (P(EGDMA‐co‐MAA))/TiO₂ hybrid microspheres. These tetra‐layer microspheres were synthesized by the combination of the distillation copolymerization of N,N(‐methylenebisacryl amide‐co‐methacrylic acid (MBA) or ethyleneglycol dimethacrylate (EGDMA) crosslinker and methacrylic acid (MAA) for the preparation of polymer core and third‐layer as well as the controlled sol‐gel hydrolysis of inorganic precursors for the construction of zirconium hydroxide (Zr(OH)₄) and titania (TiO₂) layers. The thicknesses of zirconia and titania shell‐layers were conveniently controlled via varying the feed of zirconium n‐butoxide (Zr(OBu)₄) and titanium tetrabutoxide (TBOT) during the sol‐gel hydrolysis, while the sizes of polymer layers were tuned through a multi‐stage distillation precipitation copolymerization. The structure and morphology of the resultant microspheres were characterized by transmission electron microscopy (TEM), X‐ray diffractometer (XRD), X‐ray photoelectronic spectroscopy (XPS), and thermogrametric analysis (TGA).     

STRESS-INDUCED CRYSTALLIZATION OF POLYURETHANE/MONTMORILLONITE NANOCOMPOSITE

Exfoliated polyurethane/montmorillonite nanocomposites with both high elongation at break and high tensilestrength were studied by dynamic-infrared spectroscopy (dynamic-IR). The results show that crystallization induced byadditional stress is impeded by the nano-layered organo montmorillonite.     

Study of a new novel process for preparing and co-stretching PTFE membrane and its properties

A new idea regarding improvement of the elastic recovery property of a PTFE/PU compound membrane through a co-stretching process was put forward. The experimental results show that the PTFE/PU membrane has great elastic recovery owing to PU. When the longitudinally stretching ratio of PTFE is 200%, the traverse stretching ratio is 850%, and the thickness of PU is 0.03 mm. When the longitudinally and traverse elastic recovery of PTFE/PU is 82.1% and 88.6%, respectively, the porosity is 78.0%, mean pore size is 0.382 μm, and the water vapour permeability is 9330 g/24 h m². It has been used for the SARS protective clothing in China.     

Physico-mechanical and WAXS studies of PU/PS semi interpenetrating polymer networks

The polyethylene glycol (PEG) based polyurethane (PU) and its semi interpenetrating polymer networks (SIPNs) with polystyrene (PS) were prepared. The FTIR, physico-mechanical properties like density, tensile strength, percentage elongation at break and surface hardness of the IPNs were measured. Wide angle X-ray studies (WAXS) were made to know the microcrystalline parameters such as crystal size (〈N〉), lattice disorder (g), surface (D_s) and volume (D_v) weighted crystal size of SIPNs. The different asymmetric column length distribution functions were employed using Exponential, Lognormal and Reinhold methods and the results are compared.     

COMPATIBILITY OF PVC WITH POLYURETHANES OF DIFFERENT SOFT SEGMENTS

Blends of PVC and polyurethanes with four different soft segments of molecular weight 1000 were prepared and studied by dynamic mechanical and DSC techniques. It was found that the compatibility of PVC with segmented polyurethanes was related to the mixing of PVC molecules and the soft segments of the polyurethanes. Polyester based polyurethanes are more compatible with PVC than polyether based polyurethanes. Solution cast blends of PVC with PCL-polyurethane (1/2/1) exhibit single and narrow glass transition, while the blends with PPO-polyurethane (1/2/1) are completely incompatible. The compatibility was found to decrease with increasing hard segment content for all the polyurethanes used. The methods of blend preparation may change the compatibility of PVC/PU blends through their influence on the mixing or demixing of the hard and soft segments.     

Synthesis and Characterization of Polyurethane/Poly (Urethane Modified Bismaleimide-Bismaleimide) IPNs

Themethodofblendingbyinterpenetratingpolymernetworks(IPNs)isoftenusedtoobtainelastomerswithpropertiesinexcessofthoseexhibitedbytraditionalblendingways'.Inthispaper,aseriesofnovelpolyurethane/poly(urethanemodifiedbismaleimide-bismaleimide)(PU/P(UBMI-BMI))IPNsweresynthesizedandcharacterizedby'HNMR,FTIR,TEM,andTGAanaIysis.BMIwassynthesizedasfollowsfUBMlwasintroducedtomodifythecompatibilityofthetwonetworks,whichwassynthesizedasfollows:Where(l)ishydroxyl-terminatedpoly(diethyleneadipa…     

电纺丝法制备聚乳酸/多壁碳纳米管/羟基磷灰石杂化纳米纤维的研究

电纺丝是一种利用聚合物溶液或熔体在强电场中进行喷射纺丝的加工技术,所制得的纤维、直径一般在数十纳米至几微米之间,比传统方法制得的纤维直径小几个数量级,是获得纳米尺寸长纤维的有效方法之一．