紫外光固化巯基-乙烯基硅氮烷共聚物热解研究

采用TGA-MS,FTIR和TGA-DTA等分析手段,研究了多元巯基化合物-乙烯基硅氮烷预聚物组成的紫外光固化体系制备的聚合物陶瓷前驱体共聚物在氮气中的热解机理和动力学.结果表明,裂解主要发生在280~430℃,430~560℃和560℃以上3个阶段,明确了各阶段主要发生的化学反应,发现硫元素主要是以H2S和SO2逸出.采用Vachuska-Voboril和Friedman法对不同巯基官能度和不同巯基化合物用量的共聚物热解动力学参数计算表明,增加巯基化合物官能度,第一阶段的热解反应活化能和反应级数相应增大;改变巯基化合物用量使得初始的热解活化能降低,并导致最终陶瓷收率降低.巯基与乙烯基摩尔比分别为2∶1和1∶3的共聚物的热解表观活化能(0.05≤α≤0.65时)分别为175~195 kJ/mol和95~118 kJ/mol.     

一锅法合成含磺酸基超支化聚氨酯

N-三羟甲基甲基氨基乙磺酸(TES)的胺基与异佛尔酮二异氰酸酯(IPDI)环上活性较高的NCO在低温15℃下发生选择性反应,生成AB3型单体.随后提高反应温度(70～90℃),使AB3型单体原位聚合,一锅法合成出含磺酸基超支化聚氨酯.随着聚合温度的提高,超支化聚氨酯的支化度、分子量及分子量分布系数变大.90℃时,聚合产物的Mn为22410,支化度达到0.87.以此含磺酸基超支化聚氨酯为基础制得的聚合物电解质膜具有良好的耐热性、机械强度,其锂盐室温(约25℃)的离子电导率为3.1×10-5S/cm,100℃达到1.4×10-3 S/cm.     

新型手性聚酰胺酰亚胺的合成及其热稳定性

L-异亮氨酸与3,3’,4,4’-联苯四甲酸二酐在乙酸中回流反应制得具有联苯酰亚胺结构的手性N,N’-(4,4’-二邻苯二甲酰基)-二[(S)-(+)-异亮氨酸](3);以3和二苯基甲烷二异氰酸酯为单体,通过缩聚反应合成了新型手性聚酰胺酰亚胺(5),其结构经1H NMR和IR表征。DSC测试结果表明,5在氮气氛中5%失重温度超过370℃;600℃时残余质量为60%,显示出良好的热稳定性。     

L-丙交酯-β-苹果酸共聚物的体外降解及细胞亲和性研究

研究了具有功能侧基的新型生物降解高分子——— [聚 (L 丙交酯 co β 苹果酸 ) ](PLMA)在pH 7 4的磷酸缓冲溶液中的降解和鼠的 3T3成纤维细胞在共聚物膜表面的贴附及生长 .研究了不同组成的共聚物在降解过程中的失重、表面形貌、组成及分子量变化 ,发现PLMA为本体降解 ,共聚物中苹果酸含量的提高可以加速降解 ,降解过程中聚苹果酸 (PMA)链段附近的酯键先水解断裂 .鼠的 3T3成纤维细胞在聚L 丙交酯 (PLLA)均聚物和苹果酸含量为 4mol% ,8mol%和 13mol%的共聚物膜上培养 5h ,细胞贴附率分别为 4 3%、71%、80 %和 4 3% .3T3成纤维细胞在苹果酸含量为 4mol%和 8mol%的共聚物膜上的生长情况好于在PLLA均聚物和苹果酸含量为 13mol%含量的共聚物膜上的生长 .     

硫化环氧天然橡胶的热分析

环氧化天然橡胶;热重分析;动力学;硫化环氧天然橡胶的热分析     

含芳基噻唑基团环氧树脂材料的制备及热性能

制备了一种含芳基噻唑基团热稳定环氧树脂材料(TDABZ),通过傅里叶变换红外光谱(FTIR)对其结构进行了表征,采用热重分析-微熵热重分析(TGA-DTG)计算了TDABZ的热分解动力学参数,利用热重分析(TGA)和动态热机械分析(DMTA)探讨了TDABZ的耐热性能。 结果表明,TDABZ通过TGDDM结构中的环氧基团与混合固化剂(DDS和2-ABZ)结构中的活泼氢反应,在较低的温度下就能完全交联固化。 通过Kissinger和Ozawa方法求得TDABZ的热分解活化能分别为205.5和221.9 kJ/mol。 TDABZ固化物具有优异的耐热性能,双悬臂梁法测得的玻璃化转变温度(T_g)达到242.3 ℃,在N₂气气氛下失重5%对应的温度(T_d5)为340.2 ℃,最大失重速率对应的温度(T_dmax)为395.5 ℃,600 ℃的质量保留率为24.1%,显著提高了环氧树脂的热稳定性能,拓宽了其应用领域。     

纳米碳酸钙/庚二酸复合成核剂对热致相分离法制备聚丙烯微孔膜的影响

以大豆油/邻苯二甲酸二丁酯(DBP)为混合稀释剂,采用热致相分离法(TIPS)制备聚丙烯(PP)微孔膜.研究了纳米碳酸钙成核剂、纳米碳酸钙/庚二酸复合成核剂对PP/大豆油/DBP(30/42/28,质量比)混合体系中PP结晶、熔融性能和PP微孔膜微观结构的影响.结果表明,单一纳米碳酸钙成核剂加入量为PP的0%~4%(质量百分率)时,PP/DBP/大豆油体系中PP熔融曲线上对应的峰值温度(Tpm)降到150.7~151.3℃,而纯PP的熔融峰值温度为165℃;DSC实验结果还显示加入1%~4%纳米碳酸钙和0.5%庚二酸后,导致PP的熔融曲线上出现了熔融双峰,说明纳米碳酸钙/庚二酸复合成核剂与单一成核剂相比有明显地促进β晶生成的作用,宽角X射线衍射(WAXD)实验进一步证实了β晶的存在.单一纳米碳酸钙成核剂对PP微孔膜的球晶结构和微观孔结构影响不大;加入纳米碳酸钙/庚二酸复合成核剂明显影响PP微孔膜的球晶结构和微观孔结构,其中0.5%庚二酸和1%纳米碳酸钙组成的复合成核剂制得的PP微孔膜的球晶结构明显,微孔膜孔径小且分布均匀;进一步增加纳米碳酸钙用量,PP微孔膜生成了许多细小的边界模糊的不规则结晶,微孔膜孔径不规则且尺寸较大,这与此时PP形成β晶结构有关.     

含4-苯基二氮杂萘酮结构共聚芳酯的合成及性能

以4-[4-(4羧基苯氧基)苯基]-2-(4-羧基苯基)二氮杂萘-1-酮(DHPZ-DA)、4,4'-二羧基二苯醚(DAPE)和2,2'-二(4-羟基苯基)丙烷(PBA)为原料,采用溶液缩聚法,合成了一系列聚芳酯,其数均分子量在1.2×104～1.7×104之间.通过FTIR和1H-NMR对聚芳酯结构进行了表征.该系列...     

9,9-二(4-羟基苯基)呫吨、1,4-二(4-氟苯甲酰基)苯和双酚A三元共聚物聚醚醚酮酮的合成与表征

通过亲核取代反应,将9,9-二(4-羟基苯基)呫吨(BHPX)、1,4-二(4-氟苯甲酰基)苯和双酚A(BPA)进行三元共缩聚反应,合成了几种主链含二甲基甲烷和呫吨结构的聚醚醚酮酮无规共聚物(PEEKK-X/PEEKK-A),并以FTIR、DSC、TG、WAXD等对其结构和性能进行了表征.结果表明,共聚物的玻璃化转变温度(Tg)为185～218℃,均为无定形结构,其数均分子量为39500～41600,多分散性指数为1.94～2.05.在氮气、空气气氛中,在430℃之前不分解,5%的热失重温度(Td5)分别为490～511℃、480～505℃,在氮气中700℃时的残炭率均在40%以上;在常温下易溶于非质子极性溶剂(如NMP和DMAc)以及极性较弱的溶剂(如THF和CHCl3)中.共聚物均可通过溶液浇铸成膜,所得到的薄膜韧性好,透明且耐折,其拉伸强度为58～75MPa,杨氏膜量为1.95～2.70GPa,断裂伸长率为8%～13%.当双酚单体BHPX和BPA摩尔比为60/40～50/50时,所得到的PEEKK-X/PEEKK-A共聚物更有潜在的应用前景.     

聚苯乙烯/层状双金属氢氧化物纳米复合材料的制备与表征

由离子交换法制备4,4′-偶氮二(4-氰基戊酸)根(ACP)单独插层和ACP/对苯乙烯磺酸根(VBS)复合插层的层状双金属氢氧化物(LDH),再通过原位悬浮聚合制得聚苯乙烯(PS)/LDH纳米复合材料,对插层改性LDH和复合材料进行了结构和性能表征.X-射线衍射和元素分析表明ACP可以单独或与VBS一起插入到LDH层间.透射电镜和X-射线衍射分析表明采用ACP/VBS复合插层LDH与苯乙烯原位聚合得到的复合材料中LDH剥离程度高,熔融加工后LDH基本以纳米层板形式分散在PS基体中.LDH的引入可明显提高PS的热稳定性,而熔体流动性下降.     

立规聚甲基丙烯酸热表征研究

本文对不同立构的聚甲基丙烯酸(PMAA)进行了热表征。实验结果表明,在30℃～200℃内未出现玻璃化转变。间同PMAA分别在-245℃和-280℃发生脱水反应和脱羧,而全同PMAA只在-185℃观察到脱水反应。这种热稳定性的明显差别与不同立构PMAA链上相邻羧酸距离有关。实验数据证实PMAA脱水反应为无规反应,服从一级动力学反应方程。脱水温度和间同立构含量成正比,脱水反应活化能间同PMAA比全同PMAA高～7Kcal/mol。     

Synthesis and characterization of imide modified poly(dimethylsiloxane) with maleopimaric acid as raw material

With the natural rosin derivative(maleopimaric acid,MPA) as the raw material,imide modified vinyl poly(dimethylsiloxane)(MP-VMS) was synthesized and characterized by ~1H NMR and ~(13)C NMR.The curing kinetic parameters of MP-VMS were determined by differential scanning calorimetry(DSC) at various heating rates(5,8,10,15 ℃/min) from the Kissingner.Ozawa and Crane methods.The activation energy(E_α),pre-exponential factor(A) and reaction order(n) were respectively 18.6 kJ/mol,71,108 and0.902.The low-temperature and high-temperature resistance of its curing product were respectively investigated by DSC and thermogravimetric analysis.The results showed that incorporation of MPA could significantly improve the thermal stability of silicone while had no effect on the low-temperature resistance,and the T_(max)(the temperature corresponding to the maximum weight loss rate) increased by 70.7 C.     

阻燃共聚酯的热降解动力学研究——Ⅰ.含磷共聚PET和PET的比较

1　前言ＰＥＴ(聚对苯二甲酸乙二醇酯 )由于具有优良的综合性能 ,被广泛地应用于合成纤维、薄膜和工程塑料等领域 ,但由于它的可燃性 ,在火灾事故中 ,由其着火所致占有较大比例 ,因此它的阻燃化更加引起了世界范围内学者的广泛关注[1 ] 。由于磷是对聚酯的最有效阻燃元素 ,采用共聚法制备含磷ＰＥＴ的报道较多 ,也有关于其热降解动力学研究的报道[2～ 1 0 ] 。但本文所采用的单体羟基苯氧膦丙酸 (ＣＥＰＰ)和ＰＥＴ共聚所得产物的热降解动力学研究 ,尚未见报道。研究该种含磷ＰＥＴ的热稳定性和热降解行为对研究该材料的使用范围和成型加工…     

Kinetics of the degradation of polystyrene in supercritical acetone

The kinetic analysis of the degradation of polystyrene (PS) in supercritical acetone has been studied using the nonisothermal weight loss technique with heating rates of 3, 5 and 7 °C/min. The weight loss data according to degradation temperature have been analyzed using the integral method based on Arrhenius form to obtain the kinetic parameters such as apparent activation energy and overall reaction order. The kinetic parameters obtained from this work were also compared with those of the thermal degradation of PS in nitrogen atmosphere. From this work, it was found that the activation energies of PS degradation in supercritical acetone were 73.3-200.7 kJ/mol and lower than those of the thermal degradation in nitrogen atmosphere.     

含苯侧基杂环聚芳酰胺酰亚胺的合成与性能

聚酰胺酰亚胺 (ＰＡＩ)是一类已商业化的耐热高分子材料 ,具有与聚酰亚胺类似的耐热性能 ,但是改善了聚酰亚胺的溶解性、可加工性能 ,因此进一步开发综合性能优异、加工性能好的聚芳酰胺酰亚胺近年来成为研究热点之一[1～ 3 ] .ＰＡＩ的经典制备方法为 :( 1 )偏苯三酸酰氯与芳香二胺的聚合反应 ;( 2 )含酰亚胺环的偏苯酸和异氰酸酯反应 .近年来聚酰胺酰亚胺又开发了以下途径制备 :( 1 )含亚胺环的二酸与芳香二胺一步缩聚反应 ;( 2 )含亚胺环的芳香二卤代物与二胺的催化羰基化反应等[4～ 6] .本研究组近期合成了一种新型芳香二胺 ,并合成了耐…     

Thermal Degradation Behavior and Kinetic Analysis of Ultra High Molecular Weight Polyethylene Based Multi-Walled Carbon Nanotube Nanocomposites Prepared Via in-situ Polymerization

Thermal degradation behavior of multi-wall carbon nanotubes (MWCNTs)/ultra high molecular weight polyethylene (UHMWPE) nanocomposites, with different nanotubes contents (0.5, 1.5 and 3.5 wt%) prepared via in-situ polymerization technique have been investigated using thermal gravimetric analysis (TGA). TGA spectra revealed that these nanocomposites had enhanced thermal stability and no significant mass loss (<0.4 wt%) occurred up to 350°C. Thermal degradation of these UHMWPE/MWCNT nanocomposites was investigated in terms of parameters such as the onset temperature of degradation (T₁₀), the decomposition temperature at 50% wt loss (T₅₀), the degradation temperature of maximum rate of the weight loss (T_m), and the residual yields (W_R) from TGA. The degradation activation energies (E) of virgin UHMWPE and its nanocomposites were estimated using the Friedman, the Ozawa, Flynn, and Wall (OFW), and the Kissinger's methods. Results indicated that the degradation activation energy for the virgin UHMWPE was 281.3 kJ/mol. The activation energy increased with increasing nanotube loading up to 1.5 wt% indicating that MWCNTs had a stabilizing effect on the degradation of the matrix. However, loadings of 3.5 wt% of nanotube or more could slightly decrease the activation energy. The decrease in the activation energy for degradation of nanocomposites with higher MWCNT concentrations might be attributed to the catalytic effects of nanotubes and polymerization catalyst residues. The “model fitting” method indicated a mechanism of n ^th-order auto-catalysis from the form of the conversion curves for UHMWPE/MWCNTs nanocomposites prepared via in-situ polymerization.     

THERMAL DEGRADATION KINETICS OF THERMOTROPIC COPOLY (P-OXYBENZOATE-ETHYLENE TEREPHTHALATE-VANILLATE) BY A HIGH-RESOLUTION THERMOGRAVIMETRY

Thermotropic liquid crystalline terpolymers consisting of three units of p-oxybenzoate (B), ethylene terephthalate (E), and vanillate (V), were studied through a high-resolution thermogravimetry to ascertain their thermostability and kinetics parameters of thermal decomposition in nitrogen and air. Overall activation energy data of the major decomposition have been calculated through four calculating techniques. The thermal degradation occurs in three steps in nitrogen, but in four steps in air due to an additional thermo-oxidative step. The thermal degradation temperatures are higher than 436°C in nitrogen and 424°C in air and increase with increasing B-unit content at a fixed V-unit content of 5 mol%. The temperatures at the first maximum weight-loss rate are higher than 444°C in nitrogen and 431°C in air and increase slightly with an increase in B-unit content. The first, second, and third maximum weight-loss rates almost maintain at 10–11, 10–11, and 3.6–5.3%/min regardless of copolymer composition and testing atmosphere. The char yields at 500°C in both nitrogen and air are larger than 40 wt% and increases with increasing B-unit content. But the char yields at 800°C in nitrogen and air are quite different, i.e., 18–25 wt% in nitrogen and 0 wt% in air. The activation energy and Ln (pre-exponential factor) for the major decomposition are higher in nitrogen than in air and decrease slightly with an increase in B-unit content at a given V-unit content 5 mol%. There is no regular variation in the decomposition order with the variation of copolymer composition and testing atmosphere. It is found that the most V-unit-containing terpolymer exhibited the lowest degradation temperature, lowest activation energy, and lowest Ln (pre-exponential factor). The activation energy, decomposition order, and Ln (pre-exponential factor) of the thermal degradation for the terpolymers, are situated in the ranges of 121–248 kJ/mol, 1.5–2.8, 19–38 min^?1, respectively. These results indicate that the terpolymers exhibit high thermostability. The isothermal decomposition kinetics of the terpolymer at 450°C have also been discussed and compared with the results obtained based non-isothermal high-resolution thermogravimetry.     

Ru/Mn-Ce/TiO2催化剂催化湿式氧化丁二酸的反应活性和动力学研究

在二氧化钛载体中通过掺杂Ru，Mn，Ce制备了一系列用于催化湿式氧化的催化剂，利用XRD，TEM，BET等手段对催化剂进行了表征．在反应温度T=210～270℃，氧分压Po2=2．1MPa条件下，在间歇式高压反应釜中对丁二酸进行了降解实验．催化剂在反应中有很高的催化活性．催化剂在30min内对丁二酸降解的COD去除率为54．4～98．3％．Ru及Mn，Ce的氧化物对催化活性都有促进作用．建立了丁二酸催化湿式氧化的一级分段动力学模型．基于COD的一段及二段反应的活化能分别为43．74kJ／mol和54．28kJ／mol．     

TG-FTIR研究落叶松和废轮胎共热解失重及产物释放特性

利用热重红外法(TG-FTIR)考察了不同质量混合比例(1∶2、1∶1、2∶1)落叶松和废轮胎共热解失重、动力学规律及气相产物释放特性。共热解失重特性研究发现,温度低于366℃共热解主要表现为以落叶松为主的热降解行为,温度高于366℃主要表现为以废轮胎为主的热降解行为,热解效率随着落叶松加入比例的增大而提高。采用Coats-Redfern动力学模型对共热解动力学分析发现,主要失重阶段低温区(250~370℃)和高温区(370~480℃)热解行为均符合一级动力学规律,高温区活化能均明显低于低温区,随着落叶松加入比例的增大,活化能明显降低,使得热降解更容易发生。红外分析表明,共热解过程中主要生成含氧官能团的有机物及含氧小分子气体,6种小分子气体吸收峰析出强度由大到小依次为CO2CH4H2OCOSO2H2S,其中,废轮胎中的硫在落叶松降解过程中产生的氧自由基作用下主要转化为SO2。     

煤酸异构化制对苯二甲酸

进行了煤氧化产物煤酸（水溶酸WSA）钾在催化剂碳酸镉的存在下，异构化制对苯二甲酸(TPA)的研究。主要考察了催化剂用量、二氧化碳初压、反应温度和反应时间对TPA产率的影响。结果表明，在催化剂存在下煤酸可以转化成TPA。单独煤酸钾异构化时，较佳反应条件：温度430 ℃～450 ℃，压力4.0 MPa，催化剂CdCO3用量4%，反应时间2 h。煤酸钾与苯甲酸（BA）钾混合异构化时，较佳反应条件与单独煤酸钾时基本相同。单独煤酸钾在较佳条件下异构化时，粗TPA产率达34%左右，相当于根据其中有效成分苯多羧酸（BPCA）计算的理论产率的75%左右，选择性较好。煤酸钾加苯甲酸钾在较佳条件下异构化时,粗TPA产率可达68%，扣除假定BA自身岐化生成TPA理论产量之后，则煤酸的TPA产率高达70%，比煤酸单独异构化TPA产率(34%)高1倍。粗TPA经精制可得纯度99%以上的精TPA。