环取代基对金属化聚苯胺衍生物膜修饰电极性能的影响

通过比较聚2，5－二甲氧基苯胺（PDMAn）、聚邻甲基苯胺（POT）和聚间氯苯胺（PmClAn）膜修饰电极的氧化还原电位、沉积在这3种聚合物上的铂微粒的表面形态与晶面取向以及异丙醇在分散Pt微粒的聚苯胺膜修饰电极上的氧化行为，从电子效应和立体效应探讨了聚合物电化学性质与环取代基的关系以及不同聚合基质对Pt沉积机理和有催化性能的影响,结果表明，在硫酸溶液中PDMAn膜修饰电极的氧化还原电位最负、POT次之、PmClAn最正，Pt在PDMAn和POT膜上的电沉积机理与在PmClAn膜上的不同，聚合物膜上沉积的Pt微粒呈现（200)晶面择优取向，其中POT膜上择优取向度最大，PDMAn次之，Pm-ClAn最小，异丙醇在金属化聚合物膜电极上的氧化电位取决于聚苯胺的本质，在POT膜修饰电极上异丙醇的电氧化主要发生在POT的活性电位区，而在PDMAn与PmClAn膜上的电氧化则主要发生在Pt上的氧化电位区，说明聚合物膜不仅作为Pt微粒的分散介质，而且本身有产生催化作用。     

含铈Cu-Fe-O催化剂的氧化还原性研究

用TPR等方法研究了Cu-Fe-Ce-O/γ-Al₂O₃(Ⅰ)催化剂的氧化还原性能。结果表明,在(Ⅰ)中铜的存在有利于Fe₂O₃的还原,铈作为助催化剂能增强Cu-Fe-O/γ-Al₂O₃(Ⅱ)的氧化还原性能,配合CO、NO和CO+NO气对试样进行预处理后发现,铜吸附CO的能力比铁强,铁吸附NO的能力比铜强,铈的存在可增强(Ⅱ)在NO+CO反应气氛中对CO的吸附能力,并对NO在催化剂表面吸附形成硝酸盐物种产生影响。     

不同取代基的噻碳菁和吲哚碳菁染料对其在溴化银微晶上吸附能力及形成J-聚集体尺寸分布的影响

本文研究了5-位不同取代基的噻碳菁和吲哚碳菁染料对其在立方型颗粒和T-颗粒溴化银微晶上吸附能力的影响,并采用ACFEM(Analytical Color Fluore scence Electron Microscopy)研究了上述结构染料对其吸附在溴化银微晶所形成的J-聚集体尺寸分布的影响。实验结果表明,对吲哚碳菁染料来说,立方体溴化银微晶表面的吸附能力较T-颗粒溴化银微晶表面的吸附能力强;但对噻碳菁染料来说则相反,它们在T-颗粒溴化银微晶表面的吸附能力较立方体溴化银微晶表面的吸附能力强。另外,对5-位不同取代基的噻碳菁染料而言,无论是在立方型颗粒或T-颗粒溴化银微晶上的吸附能力来说,含取代基(无论4-取代基是吸电子型还是推电子型)的噻碳菁染料较未取代的噻碳菁染料强;而5-位取代基是吸电子型的噻碳菁染料更有利于其吸附在T-颗粒溴化银微晶表面。此外,本文还进一步证明了溴化银微晶表面上染料J-聚集体的生长过程是符合奥斯瓦尔特成熟过程的。吲哚碳菁染料在T-颗粒溴化银微晶上形成的J-聚集体的平均尺寸明显大于在立方体溴化银微晶上形成的J-聚集体的平均尺寸。吸附在立方体溴化银微晶上的5-不同取代基的噻碳菁染料对其形成J-聚集体尺寸分布的影响的研究结果表明,含取代基(-CH₃,-Ph,-Cl)的噻碳菁染料形成的J-聚集体的尺寸分布几乎相同,但与未取代的噻碳菁染料形成的J-聚集体的尺寸分布明显不同;5-位含取代基的噻碳菁染料形成的J-聚集体平均尺寸大于未取代的噻碳菁染料的。     

Recent progress in experiments for sessile droplet wetting on structured surfaces

Wetting of a sessile droplet on structured or patterned surface can be found in a broad range of applications. The researchers have been promoted to keep working on the topic. The review is on the basis of the recent experimental advances on the sessile droplet wetting on the hydrophobic, hydrophilic, or combined hydrophobic and hydrophilic surfaces under isothermal conditions, and on heating or cooling substrates having nonisothermal conditions. More attention has been paid on the wetting configuration between the sessile droplet and the structured substrate; the research gap has been discussed on identifying the three-phase line shape. Further, the three-dimensional measurement for the sessile droplets on the patterned surfaces with focusing more on the contact line of sessile droplets might reveal new physical insights. This review targets at building a holistic overview on the sessile droplet wetting behaviors on the structured substrate in the past 2 years.     

阻光染料对氯化银乳剂光谱增感的影响

增感染料在卤化银微晶上吸附并形成J-聚集体是染料光谱增感和超增感的关键步骤.本文利用紫外-可见吸收光谱研究了增感染料和阻光染料在氯化银微晶上的吸附,并考察了阻光染料对增感染料J-聚集体的形成及乳剂感光性能的影响.结果表明:不同阻光染料在氯化银微晶表面的吸附程度不同,对增感染料J-聚集体形成的影响也有差异.其中,吸附较小的不影响增感染料J-聚集体的形成,而吸附较大的阻碍增感染料J-聚集形成,特别是阻光染料在增感染料之前加入乳剂中时.在氯化银微晶上吸附很小的阻光染料基本不影响增感染料对乳剂的光谱增感,而吸附较强的阻光染料不仅吸收入射光,还抑制或破坏增感染料的光谱增感.因此,在氯化银微晶表面没有吸附的阻光染料才是优良的阻光染料.     

Influence of Mg^2＋ on Initial Stages of CaCO3 Scale Formed on Metal Surface

Magnesium ions, which exist in formation water and injection water under downhole conditions in the oil and gas production industry, are a key determinant in the CaCO3 scale formation. Many studies have focused their attention on the effect of magnesium on the kinetics, the morphology and the content of Mg in the Ca-CO3 scale. Little attention has been paid to the effect of Mg^2 on the initial stages of CaCO3 formation on a metal surface. In this study, an electrochemical technique was used to study the influence of Mg^2 on the ini-tial stages of CaCO3 scale formed on a metal surface. With this electrochemical technique, the reduction of the dissolved oxygen in an analysis solution is considered on the surface of a rotating disk electrode (RDE) un-der potentiostatic control. The rate of oxygen reduction on the surface of the RDE enables the extent of sur-face coverage of scale to be assessed. With this electrochemical technique, a new insight into the effect of Mg^2 on CaCO3 scale formed on a metal surface is given.     

ToF‐SIMS and principal component analysis: Effect of film thickness on crystal surfaces of polymers

The effect of film thickness on the structural conformation of the surfaces of the amorphous state, edge‐on lamellae and flat‐on lamellae of a semiflexible polymer, poly(bisphenol‐A‐etheroctane), was investigated by time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) with the aid of principal component analysis (PCA). PCA results empirically indicate that a structurally regular polymer surface was obtained with the formation of the flat‐on lamellae from the amorphous state at a low degree of supercooling. A higher concentration of end group and cilium ion fragments, which are indicative of free chain ends, was observed on the edge‐on lamellar surfaces than on the amorphous and the flat‐on lamellar surfaces. This finding was attributed to the fact that the lateral surface of the edge‐on lamellae contains many growth fronts, leaving behind a large number of uncrystallized chain remnants on the surfaces. Structural disorder was facilitated on both edge‐on and flat‐on lamellar surfaces as the film thickness decreased. Hence, this PCA study offers new insights into the nonequilibrium nature of polymer crystals and the mechanism of polymer crystallization in thin and ultrathin films. Copyright © 2010 John Wiley & Sons, Ltd.     

核酸的有机化学研究在分子生物学发展中的作用

本文主要综述有机化学在建立核酸的顺序测定法和自动顺序仪,在破译遗传密码,在建立核酸片段的化学合成方法,固相合成法及DNA合成仪的设计,在合成许多有生物活力的核酸分子,在发展并完善遗传工程以及新近发现酶RNA(Ribozyme)等方面的卓越贡献。最后简要地展望有机化学将对生物学发展作出进一步贡献的几个方面。     

A Comparative Study of Electrochemical Reduction of 4‐Nitrophenyl Covalently Grafted on Gold and Carbon

4‐Nitrophenyl layers were grafted on gold and glassy carbon surfaces by electrochemical reductive adsorption of the corresponding diazonium salt. Electrochemical conversion efficiencies of 4‐nitrophenyl moieties to 4‐aminophenyl moieties on gold versus on glassy carbon in a protic medium were investigated using X‐ray photoelectron spectroscopy (XPS). In total contrast to all previous comparative studies showing greater electrochemical reactivity of aryl diazonium salt‐derived layers on gold than on glassy carbon, a much lower rate of conversion to 4‐aminophenyl was observed on gold than on glassy carbon by both cyclic voltammetry (CV) and chronoamperometry (CA) methods. The lower electron transfer rate during conversion observed on gold versus glassy carbon was proposed to be due to a mechanism related to the molecular structure rearrangement of 4‐nitrophenyl during the process on glassy carbon. However, whilst complete conversion of 4‐nitrophenyl to 4‐aminophenyl on gold by chronoamperometry was achieved, on glassy carbon complete reduction could not be achieved under the same conditions.     

Underwater Oil Wettability on Nanostructured Superamphiphobic Surface Tuned by Trapped Air Layer Continuity

When the superamphiphobic meshes are immersed in water, the rough structures on steel wires are filled with air. The nanostructured superamphiphobic surfaces were prepared on the stainless-steel mesh. By adjusting the mesh size of the surface, the continuity of trapped air layer on the superamphiphobic surface underwater could be controlled. Then the underwater oil-wetting behavior on the prepared superamphiphobic mesh was investigated. The oil droplet spread out on the superamphiphobic surface without mesh and exhibited an oil contact angle of about 0° under water. But the oil contact angle formed on the superamphiphobic mesh surfaces and extended with increasing mesh size. We thought the discontinuity of trapped air layer on the surface and the entry of water into interval between the steel wires should be responsible for these behaviors.     

大孔吸附树脂对邻甲酚的吸附行为研究

研究了大孔吸附树脂NDA—909吸附水溶液中邻甲酚的热力学特征，并与Amberlite XAD—4树脂进行了比较．通过吸附动力学实验，初步探讨了初始温度对吸附过程的影响。结果表明，NDA—909对邻甲酚的吸附符合Freundlich经验公式，表现为放热的物理吸附过程．此外吸附速率受颗粒内扩散和其它类型扩散的共同控制。     

Growth and characterization of pyrene crystals on carbon nanofibers

Pyrene crystals were grown on carbon nanofibers (CNFs) by dispersing pyrene polycrystals and CNFs in water during ultrasonic irradiation, and they were characterized by scanning electron microscopy, X-ray diffractometry (XRD) and spectroscopy. The XRD measurements indicated that the orientation and size of the pyrene crystals on the CNF aggregates were different from that of the added pyrene polycrystals. Based on the spectroscopic properties of the pyrene crystals on the CNFs, the pyrene crystals on the CNF aggregates and on the individual CNFs were determined to be polycrystals and single crystals, respectively. These results indicate that pyrene crystals are produced on the CNFs by recrystallization of the added pyrene polycrystals and their crystal states depend on the aggregation state of the CNFs.     

Sorption of nonylphenol on Na-Montmorillonite

Sorption of nonylphenol on Na-montmorillonite was studied by batch experiment and compared with that on -SiO₂, -Al₂O₃ and gibbsite. It was found that sorption of nonylphenol on Na-montmorillonite reached the equilibrium state within 24 h, and that the interlayer width of Na-montmorillonite did not change before and after the sorption. These suggest that nonylphenol was sorbed on the outer surface of Na-montmorillonite. Sorption isotherms of nonylphenol on Na-montmorillonite, -SiO₂, -Al₂O₃ and gibbsite were studied. Sorption amount of nonylphenol on the surface of octahedral sheets of Na-montmorillonite was found to be identical to that of gibbsite. On the other hand, sorption amount on -Al₂O₃ was smaller, and that on -SiO₂ was fairly few. Dependence of sorption onto Na-montmorillonite on pH and ionic strength was also examined. Sorption amount was found to increase monotonously with pH. Sorption amount decreased with ionic strength in the low ionic strength region, reached to a minimum and then increased with ionic strength. These results might suggest that nonylphenol was sorbed on the broken-edges of octahedral alumina sheets of Na-montmorillonite.     

Electrocatalytic reduction of dioxygen at platinum particles deposited on Nafion- and clay-coated electrodes

Nafion- and clay-coated electrodes are prepared by casting a known amount of Nafion and clay solutions on the glassy carbon electrode (GC) surface. Subsequently platinum (Pt) particles are deposited on the GC electrodes and on the Nafion- and clay-coated GC electrodes. The formation of Pt particles on the modified electrode surface is analysed by scanning electron microscope, while cyclic voltammetry provides information on the anodisation of Pt particles deposited on the GC electrodes at >0.5 V(SCE) leading to the formation of platinum oxide (PtO). The involvement of PtO on the catalysed dioxygen reduction to hydrogen peroxide is reported. Macrocyclic cobalt(III) complex is also used as the electrocatalyst. The effect of pH on the reduction of PtO and dioxygen in deaerated and oxygenated solutions is studied to understand the dioxygen reduction processes. Received: 24 January 1997 / Accepted: 14 April 1997     

Pt/HL和Pt/KL沸石在异丙醇分解反应中的不同催化行为

Ｐｔ／ＫＬ沸石在异丙醇分解反应中具有很高的脱氢活性,而Ｐｔ／ＨＬ沸石具有明显的缺电子性,在此反应中难以显示出脱氢活性,通过加氢作用,可使沸石的酸位免受积炭覆盖,从而可增强Ｐｔ／ＨＬ沸石的酸性催化作用。     

Influence of molecular order on the local work function of nanographene architectures: a Kelvin-probe force microscopy study.

We report a Kelvin-probe force microscopy (KPFM) investigation on the structural and electronic properties of different submicron-scale supramolecular architectures of a synthetic nanographene, including extended layers, percolated networks and broken patterns grown from solutions at surfaces. This study made it possible to determine the local work function (WF) of the different pi-conjugated nanostructures adsorbed on mica with a resolution below 10 nm and 0.05 eV. It revealed that the WF strongly depends on the local molecular order at the surface, in particular on the delocalization of electrons in the pi-states, on the molecular orientation at surfaces, on the molecular packing density, on the presence of defects in the film and on the different conformations of the aliphatic peripheral chains that might cover the conjugated core. These results were confirmed by comparing the KPFM-estimated local WF of layers supported on mica, where the molecules are preferentially packed edge-on on the substrate, with the ultraviolet photoelectron spectroscopy microscopically measured WF of layers adsorbed on graphite, where the molecules should tend to assemble face-on at the surface. It appears that local WF studies are of paramount importance for understanding the electronic properties of active organic nanostructures, being therefore fundamental for the building of high-performance organic electronic devices, including field-effect transistors, light-emitting diodes and solar cells.     

多相聚合物体系相界面研究进展

综述了多相聚合物体系相界面的形成、界面层状态的表征、界面层性质及其对体系性能的影响。重点论述了不同类型增容剂对界面行为的影响，其中对嵌段型增容剂的分子量、浓度等因素对界面行为的影响建立了定量关系；而对接枝型和无规增容剂对界面行为的影响研究较少，有待发展。指出了在界面张力、界面层厚度与多相聚合物体系性能，尤其是力学性能之间建立量化关系是高分子物理领域一个可以期待的发展方向。     

Aminosäuren und die Entstehung des Lebens. Spuren aus dem Weltraum

In order to better understand the origin of life on Earth the most recent chemical experiments are presented that successfully simulated the prebiotic genesis of amino acids. Surprisingly, laboratory samples of interstellar ice do not only contain classic amino acids but also diamino acids. Diamino acids are discussed to have triggered the appearance of the first genetic material, the peptide nucleic acid, on Earth. The European Rosetta‐mission that will pose a lander on a cometary surface hopefully will verify the outlined hypotheses on modern theories on the origin of life on Earth by analyzing cometary ice samples in situ.     

Low-temperature heterogeneous oxidation of sulfide ions on a higher Co oxide system in aqueous medium

Low-temperature heterogenous oxidation of sulfide ions on a higher Co oxide system in aqueous medium has been studied. The effects of pH, temperature and catalyst amount on the kinetic parameters as well as on the selectivity of the oxidation process were investigated. An oxidation mechanism has been proposed based on the results of kinetic investigations and on the data obtained by IR and XPS spectroscopic studies of Co oxide before and after sulfide ion oxidation.     

稠环芳烃在烷基膦酸改性锆镁复合氧化物固定相上的反相液相色谱保留行为

以稠环芳烃为探针 ,考察了烷基膦酸改性锆镁复合氧化物材料的反相色谱性能。研究了稠环芳烃类化合物的结构与其保留值的关系 ,比较了烷基膦酸改性锆镁复合氧化物固定相和十八烷基键合硅胶 Zorbax ODS对稠环芳烃异构体的选择性 ,并对可能的保留机理进行了讨论。以甲醇 -水 (体积比为 75∶ 2 5)为流动相 ,在烷基膦酸改性锆镁复合氧化物固定相上分离了 8种稠环芳烃类化合物