Cation distribution in co-doped ZnAl2O4 nanoparticles studied by X-ray photoelectron spectroscopy and 27Al solid-state NMR spectroscopy

Co(x)Zn(1-x)Al(2)O(4) (x = 0.01-0.6) nanoparticles were synthesized by the citrate sol-gel method and were characterized by X-ray powder diffraction and transmission electron microscopy to identify the crystalline phase and determine the particle size. X-ray photoelectron spectroscopy and (27)Al solid-state NMR spectroscopy were used to study the distribution of the cations in the tetrahedral and octahedral sites in Co(x)Zn(1-x)Al(2)O(4) nanoparticles as a function of particle size and composition. The results show that all of the as-synthesized samples exhibit spinel-type single phase; the crystallite size of the samples is about 20-50 nm and increases with increasing annealing temperature and decreases with Co-enrichment. Zn(2+) ions are located in large proportions in the tetrahedral sites and in small proportions in the octahedral sites in Co(x)Zn(1-x)Al(2)O(4) nanoparticles. The fraction of octahedral Zn(2+) increases with increasing Co concentration and decreases with increasing particle size. Besides the tetrahedral and octahedral coordinations, the presence of the second octahedrally coordinated Al(3+) ions is observed in the nanoparticles. The change of the inversion parameter (2 times the fraction of Al(3+) ions in tetrahedral sites) with Co concentration and particle size is consistent with that of the Zn fraction in octahedral sites. Analysis of the absorption properties indicates that Co(2+) ions are located in the tetrahedral sites as well as in the octahedral sites in the nanoparticles. The inversion degree of Co(2+) decreases with increasing particle size.     

Ce0.5+xZr0.4-xLa0.1O2-Al2O3催化剂催化燃烧柴油车碳烟

采用共沉淀法制备了系列Ce_0.5+xZr_0.4-xLa_0.1O₂-Al₂O₃催化剂, 其中0≤x≤0.4且Ce_0.5+xZr_0.4-xLa_0.1O₂与Al₂O₃的质量比为1:1. 考察了该系列催化剂对柴油车排放碳烟的催化燃烧性能, 并用低温N2吸附-脱附、X射线衍射(XRD)、X射线光电子能谱(XPS)、氢气程序升温还原(H₂-TPR)和氧气程序升温脱附(O₂-TPD)等手段对催化剂进行了表征. 研究结果表明该系列催化剂均形成了具有立方萤石结构的固溶体. 当x=0.2时, Ce³⁺离子在催化剂表面有一定的富集, 此时催化剂具有最大的β氧脱附峰和最好的表面还原性能, 同时具有良好的催化碳烟氧化活性, 碳烟在该催化剂的起燃温度为360 °C, 具有较好的应用前景.     

Stability and structural evolution of Ce(IV)(1-x)Ln(III)(x)O(2-x/2) solid solutions: a coupled μ-Raman/XRD approach

Several CeO(2)-based mixed oxides with general composition Ce(1-x)Ln(x)O(2-x/2) (for 0 ≤ x ≤ 1 and Ln = La, Nd, Sm, Eu, Gd, Dy, Er, or Yb) were prepared using an initial oxalic precipitation leading to a homogeneous distribution of cations in the oxides. After characterization of the Ce/Nd oxalate precursors and then thermal conversion to oxides at T = 1000 °C, investigation of the crystalline structure of these oxides was carried out by XRD and μ-Raman spectroscopy. Typical fluorite Fm ?3m structure was obtained for relatively low Ln(III) contents, while a cubic Ia ?3? superstructure was evidenced above x ≈ 0.4. Moreover, since Nd(2)O(3) does not crystallize with the Ia ?3?-type structure, two-phase systems composed with additional hexagonal Nd(2)O(3) were obtained for x(Nd) ≥ 0.73 in the Ce(1-x)Nd(x)O(2-x/2) series. The effect of heat treatment temperature on these limits was explored through μ-Raman spectroscopy, which allowed determining the presence of small amounts of the different crystal structures observed. In addition, the variation of the Ce(1-x)Ln(x)O(2-x/2) unit cell parameter was found to follow a quadratic relation as a result of the combination between increasing cationic radius, modifications of cation coordination, and decreasing O-O repulsion caused by oxygen vacancies.     

Phase evolution, phase transition, raman spectra, infrared spectra, and microwave dielectric properties of low temperature firing (K(0.5x)Bi(1-0.5x))(Mo(x)V(1-x))O4 ceramics with scheelite related structure

In the present work, the (K(0.5x)Bi(1-0.5x))(Mo(x)V(1-x))O(4) ceramics (0≤x ≤ 1.00) were prepared via the solid state reaction method and sintered at temperatures below 830 °C. At room temperature, the BiVO(4) scheelite monoclinic solid solution was formed in ceramic samples with x < 0.10. When x lies between 0.1-0.19, a BiVO(4) scheelite tetragonal phase was formed. The phase transition from scheelite monoclinic to scheelite tetragonal phase is a continuous, second order ferroelastic transition. High temperature X-ray diffraction results showed that this phase transition can also be induced at high temperatures about 62 °C for x = 0.09 sample, and has a monoclinic phase at room temperature. Two scheelite tetragonal phases, one being a BiVO(4) type and the other phase is a (K,Bi)(1/2)MoO(4) type, coexist in the compositional range 0.19 < x < 0.82. A pure (K,Bi)(1/2)MoO(4) tetragonal type solid solution can be obtained in the range 0.82 ≤ x ≤ 0.85. Between 0.88 ≤ x ≤ 1.0, a (K,Bi)(1/2)MoO(4) monoclinic solid solution region was observed. Excellent microwave dielectric performance with a relative dielectric permittivity around 78 and Qf value above 7800 GHz were achieved in ceramic samples near the ferroelastic phase boundary (at x = 0.09 and 0.10).     

Structural study of ternary iron-lead-germanate glass ceramics

Glass ceramics with the composition xFe(2)O(3)·(100-x)[7GeO(2)·3PbO(2)] where 0≤x≤60 mol% were obtained and studied using XRD, FTIR and UV-vis spectroscopy investigations. Heat treatment of glass samples at 400°C for 8 h led to the formation of α, γ-PbGe(4)O(9), Pb(3)Fe(2)Ge(4)O(14) and PbO(1.44) crystalline phases. The content of these crystalline phases depends of Fe(2)O(3) concentration. FTIR spectroscopy data suggest that the lead ions have a pronounced affinity towards [GeO(5)] structural units containing non-bridging oxygens and [FeO(4)] anions producing formation of the Pb(3)Fe(2)Ge(4)O(14) crystalline phase. The introduction of low concentrations of Fe(2)O(3) into the host matrix results in the formation of new absorption UV bands between 320 and 450 nm. These bands arise from to the d-d transitions of the Fe(+3) ions. The light absorption in the range from 250 to 600 nm increases with increasing iron oxide content in matrix network, accompanied with the changes on color from white to brown yellow and darker brown.     

Type-I clathrate Ba8Ni(x)Si(46-x): phase relations, crystal chemistry and thermoelectric properties

The phase relations, crystal structure and thermoelectric properties of the type-I solid solution Ba(8)Ni(x)Si(46-x) were investigated. Based on X-ray diffraction, differential thermal analysis and electron probe microanalysis data, a partial phase diagram was constructed for the Si-rich part of ternary system Ba-Ni-Si at 800 °C. The solubility range of Ni in the clathrate-I phase at 800 °C was determined (2.9 ≤x≤ 3.8) and thermoelectric properties, namely electrical resistivity, Seebeck-coefficient and thermal conductivity, were measured in the temperature range from 300 to 850 K. A shift of the thermoelectric properties from a predominantly metallic to a more semiconducting behavior was observed for an increasing Ni-content. Density functional calculations revealed a significant decrease of the gap width in the density of states induced by the incorporation of Ni. Electrical resistivity and Seebeck coefficients for Ba(8)Ni(x)Si(46-x) with 3.3 ≤x≤ 3.8 have been modeled within the rigid band approximation.     

Epitaxial thin films of ATiO(3-x)H(x) (A = Ba, Sr, Ca) with metallic conductivity

Epitaxial thin films of titanium perovskite oxyhydride ATiO(3-x)H(x) (A = Ba, Sr, Ca) were prepared by CaH(2) reduction of epitaxial ATiO(3) thin films deposited on a (LaAlO(3))(0.3)(SrAl(0.5)Ta(0.5)O(3))(0.7) substrate. Secondary ion mass spectroscopy detected a substantial amount and uniform distribution of hydride within the film. SrTiO(3)/LSAT thin film hydridized at 530 °C for 1 day had hydride concentration of 4.0 × 10(21) atoms/cm(3) (i.e., SrTiO(2.75)H(0.25)). The electric resistivity of all the ATiO(3-x)H(x) films exhibited metallic (positive) temperature dependence, as opposed to negative as in BaTiO(3-x)H(x) powder, revealing that ATiO(3-x)H(x) are intrinsically metallic, with high conductivity of 10(2)-10(4) S/cm. Treatment with D(2) gas results in hydride/deuteride exchange of the films; these films should be valuable in further studies on hydride diffusion kinetics. Combined with the materials' inherent high electronic conductivity, new mixed electron/hydride ion conductors may also be possible.     

Pd2+/Pd0 redox cycling in hexagonal YMn(0.5)Fe(0.5)O3: implications for catalysis by PGM-substituted complex oxides

Complex oxides--containing at least two different cations on crystallographically distinct sites--have recently been shown to display redox cycling of platinum group metals (PGMs), such as Pd; for example, Pd-substituted complex oxides can reversibly extrude metallic Pd under reducing conditions and then reincorporate Pd(2+) ions into the lattice under oxidizing conditions. The title compounds, YMn(0.5)Fe(0.5-x)Pd(x)O(3-δ) (0 ≤ x ≤ 0.07) crystallizing in the noncentrosymmetric YMnO(3) structure, were prepared using a sol-gel process at 800 °C, and the structures were refined from high-resolution synchrotron X-ray powder diffraction data. Their redox cycling behavior was monitored using synchrotron X-ray diffraction and EXAFS studies. In contrast to the previously studied complex oxide host compounds, YMn(0.5)Fe(0.5-x)Pd(x)O(3-δ) is only modestly tolerant to cycling: repeated redox cycling leads to the formation of PdO, which, on the time-scale of the oxidation cycles, does not reincorporate in the complex oxide lattice. Both oxidized and reduced samples were tested for the oxidation of CO to CO(2) under CO-lean conditions. YMn(0.5)Fe(0.5-x)Pd(x)O(3-δ) performs essentially as well as previously studied YFe(1-x)Pd(x)O(3-δ). The CO oxidation light-off characteristics of the hexagonal hosts are very similar to finely dispersed PdO. Despite evidence that Pd is almost fully dispersed as divalent ions in the host lattice, which is presumably accompanied by the concurrent creation of oxygen vacancies (2 Pd(2+):1 V(O(2-))), the as-prepared hexagonal materials do not display any significant improvement in catalytic activity as a function of Pd substitution level. This suggests that the corner-connected trigonal bipyramids that characterize this structural family do not enable the transport of oxygen through the bulk of the lattice. The study casts light on factors in the solid-state chemistry of precious metal-substituted complex oxides that influence the efficacy of redox cycling of the precious metal, and catalytic performance.     

Preparation, characterization and ESR studies of bulk and nano sized pyrochlore La2-xGdxZr2O7 (x=0.025, 0.05, 0.075 and 0.1)

Bulk and nano sized pyrochlore of composition La(2-x)Gd(x)Zr(2)O(7) (x=0.025, 0.05, 0.075 and 0.1) have been prepared by sol-gel method. They are characterized by powder X-ray diffraction and infrared spectroscopy. The sintering temperature influences the particle size of the sample. The room temperature powder ESR of La(1.95)Gd(0.05)Zr(2)O(7) gave characteristic "U" spectrum. The influence of particle size on the ESR of Gd(3+) is investigated. Possible reason for the disappearance of "U" spectrum with increase in the particle size is given.     

Thermochemistry of Sr2Ce(1-x)Pr(x)O4 (x = 0, 0.2, 0.5, 0.8, and 1): variable-temperature and -atmosphere in-situ and ex-situ powder X-ray diffraction studies and their physical properties

A novel family of metal oxides with a chemical formula of Sr(2)Ce(1-x)Pr(x)O(4) (x = 0, 0.2, 0.5, 0.8, and 1) was developed as mixed oxide ion and electronic conductors for solid oxide fuel cells (SOFCs). All of the investigated samples were synthesized by the ceramic method at 1000 °C in air and characterized by powder X-ray diffraction (PXRD), selected area electron diffraction (SAED), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), and electrochemical impedance spectroscopy (EIS). Ex-situ PXRD reveals that the Sr(2)PbO(4)-type Sr(2)CeO(4) decomposes readily into a mixture of perovskite-type SrCeO(3) and rock-salt-type SrO at 1400 °C in air. Surprisingly, the decomposed products are converted back to the original Sr(2)PbO(4)-type Sr(2)CeO(4) phase at 800 °C in air, as confirmed by in-situ PXRD. Thermal decomposition is highly suppressed in Sr(2)Ce(1-x)Pr(x)O(4) compounds for Pr > 0, suggesting that Pr improves the thermal stability of the compounds. Rietveld analysis of PXRD and SAED supported that both Pr and Ce ions are located on the 2a site in Pbam (space group no. 55). The electrical transport mechanism could be correlated to the reduction of Pr and/or Ce ions and subsequent loss of oxide ions at elevated temperatures, as shown by TGA and in-situ PXRD. Conductivity increases with Pr content in Sr(2)Ce(1-x)Pr(x)O(4). The highest total conductivity of 1.24 × 10(-1) S cm(-1) was observed for Sr(2)Ce(0.2)Pr(0.8)O(4) at 663 °C in air.     

Substitutional mechanism of Ni into the wide-band-gap semiconductor InTaO4 and its implications for water splitting activity in the wolframite structure type

The mechanism of Ni substitution into the oxide semiconductor InTaO(4) has been studied through a combination of structural and spectroscopic techniques, providing insights into its previously reported photoactivity. Magnetic susceptibility and X-ray absorption near-edge spectroscopy (XANES) measurements demonstrate that nickel is divalent within the host lattice. The combined refinement of synchrotron X-ray and neutron powder diffraction data indicates that the product of Ni doping has the stoichiometry of (In(1-x)Ni(2x/3)Ta(x/3))TaO(4) with a solubility limit of x ≈ 0.18, corresponding to 12% Ni on the In site. Single-phase samples were only obtained at synthesis temperatures of 1150 °C or higher due to the sluggish reaction mechanism that is hypothesized to result from small free energy differences between (In(1-x)Ni(2x/3)Ta(x/3))TaO(4) compounds with different x values. Undoped InTaO(4) is shown to have an indirect band gap of 3.96 eV, with direct optical transitions becoming allowed at photon energies in excess of 5.1 eV. Very small band-gap reductions (less than 0.2 eV) result from Ni doping, and the origin of the yellow color of (In(1-x)Ni(2x/3)Ta(x/3))TaO(4) compounds instead results from a weak (3)A(2g) → (3)T(1g) internal d → d transition not associated with the conduction or valence band that is common to oxide compounds with Ni(2+) in an octahedral environment.     

Local structural distortion of BaZr(x)Ti(1-x)O3 nanocrystals synthesized at room temperature

Single crystalline, sub-15 nm BaZr(x)Ti(1-x)O(3) (0 ≤x≤ 1) nanocrystals were synthesized at room temperature via the vapor diffusion sol-gel method. As-prepared nanocrystals exhibit noncentrosymmetric regions whose volume fraction increases significantly upon substitution of small amounts of Zr(4+) for Ti(4+) and reaches a maximum for substitution levels ranging from 10 to 20 mol%.     

Investigation of the first-order phase transition in the Co(1-x)Mg(x)MoO4 solid solution and discussion of the associated thermochromic behavior

A series of compounds of Co(1-x)Mg(x)MoO(4) compositions has been prepared by a conventional ceramic route. The members of the whole solid solution exhibit a reversible first-order phase transition which was probed by using thermal expansion and low-temperature reflectivity techniques. Whereas the α → β transition temperature evolves linearly on warming from 435 to 200 °C with x going from 0 to 0.9, the β → α transition temperature variation falls down on cooling from -40 °C to -140 °C going from CoMoO(4) to Co(0.1)Mg(0.9)MoO(4) with an asymptotic evolution. The phase transition temperatures have been explained on the basis of a crystal polarization effect under substitution of Mg for Co. Thus, from an applicative point of view, new thermochromic pigments with tunable transition temperatures are here proposed.     

O2结构Liy[Mn1—xMx]O2（M＝Cr，Mg）的合成及结构研究

由高温焙烧法制备层状前驱体Na_(2/3)[Mn_(1-x)M_x]O_2（M＝Cr, Mg），再 经离子交换反应得到层状O2结构产物Li_y-[Mn_(1-x)M_x]。XRD表明Li_y[Mn_(1-x) M_x]O_2属六方晶系，P3ml空间群。Cr的添加量对前驱体的晶体结构有很大影响： 随着x值的增大，前驱体逐渐由层状P2结构Na_(2/3)[Mn_(1-x)Cr_x]O_2向正交结构 Na_4Mn_90_(18)转变。由SEM可以看到样品Li_y[Mn_(1-x)Cr_x]-O_2(x≤0.05)具有 六方层状结构。XPS分析结果表明样品Li_y[Mn_(0.95)Cr_(0.05)]O_2表面上的Mn和 Cr分别以Mn~(4+)存在，并且表面中Cr相对含量高于体相，而样品Li_y[Mn_(0.90) Mg_(0.10)]O_2的表面Mn和Mg分别以Mn~(4+)和Mg~(2+)存在，Mg/Mn比在表面与体相 基要一致。     

Cd(1-x)Zn(x)O [0.05 ≤x≤ 0.26] synthesized by vapor-diffusion induced hydrolysis and co-nucleation from aqueous metal salt solutions

Nanoparticulate Cd(1-x)Zn(x)O (x = 0, 0.05-0.26, 1) is synthesized in a simple two-step synthesis approach. Vapor-diffusion induced catalytic hydrolysis of two molecular precursors at low temperature induces co-nucleation and polycondensation to produce bimetallic layered hydroxide salts (M = Cd, Zn) as precursor materials which are subsequently converted to Cd(1-x)Zn(x)O at 400 °C. Unlike ternary materials prepared by standard co-precipitation procedures, all products presented here containing < 30 mol% Zn(2+) ions are homogeneous in elemental composition on the micrometre scale. This measured compositional homogeneity within the samples, as determined by energy dispersive spectroscopy and inductively coupled plasma spectroscopy, is a testimony to the kinetic control achieved by employing slow hydrolysis conditions. In agreement with this observation, the optical properties of the materials obey Vegard's Law for a homogeneous solid solution of Cd(1-x)Zn(x)O, where x corresponds to the values determined by inductively coupled plasma analysis, even though powder X-ray diffraction shows phase separation into a cubic mixed metal oxide phase and a hexagonal ZnO phase at all doping levels.     

LaCo(1-x)Ni(x)O(3) with Improved Electrical Conductivity

To determine the applicability of LaCo(1-x)Ni(x)O(3) in a conductive material for electrical wiring, the dependence of the electronic transport property on the Ni content is investigated via Hall effect measurements, Rietveld analyses, and band-structure calculations. Ni doping (50 mol %) into the Co sites realizes a high electrical conductivity of 1.9 × 10(3) S/cm, which is an unexpectedly high value for a LaCo(1-x)Ni(x)O(3) system, at room temperature due to the high carrier concentration of 2.2 × 10(22) cm(-3) and the small effective mass of 0.1 m(e). In addition, the high electrical conductivity is maintained from room temperature to 900 °C; that is, the temperature coefficient of the conductivity is smaller than that of standard metals. Thus, the results indicate that LaCo(0.5)Ni(0.5)O(3) is suitable as a conductive material for electrical wiring at high temperatures in air.     

Structural evolution and properties of solid solutions of hexagonal InMnO3 and InGaO3

Solid solutions InMn(1-x)Ga(x)O(3) (0 ≤ x ≤ 1) have been investigated using magnetic, dielectric, specific heat, differential scanning calorimetry (DSC), and high-temperature powder synchrotron X-ray diffraction (HT-SXRD) measurements. It was found that samples with 0.5 ≤ x ≤ 1 crystallize in space group P6(3)/mmc with a ~ 3.32 ? and c ~ 11.9 ?, and samples with 0.0 ≤ x ≤ 0.4 crystallize in space group P6(3)cm with a ~ 5.8 ? and c ~ 11.6 ? at room temperature. HT-SXRD data revealed the existence of a P6(3)cm-to-P6(3)/mmc phase transition at about 480 K in InMn(0.6)Ga(0.4)O(3) and at 950 K in InMn(0.7)Ga(0.3)O(3). However, no dielectric, phonon, second-harmonic-generation, or DSC anomalies were found to be associated with these phase transitions. The phase transition should be improper ferroelectric from the symmetry point of view, but the above-mentioned experimental facts, together with the absence of ferroelectric hysteresis loops, revealed no evidence for ferroelectricity in the low-temperature P6(3)cm structure. We suggest that InMn(1-x)Ga(x)O(3) corresponds to a nonferroelectric phase of hexagonal RMnO(3) with P6(3)cm symmetry. The antiferromagnetic phase-transition temperature decreases from 118 K for x = 0 to 105 K for x = 0.1 and 73 K for x = 0.2, and no long-range magnetic ordering could be found for x ≥ 0.3. Specific heat anomalies associated with short-range magnetic ordering were observed for 0.0 ≤ x ≤ 0.5. InMn(1-x)Ga(x)O(3) with small Mn contents (0.8 ≤ x ≤ 0.98) has a bright-blue color.     

Mullite-derivative Bi2Mn(x)Al(7-x)O14 (x~1): structure determination by powder X-ray diffraction from a multi-phase sample

As a supplementary method to single crystal X-ray diffraction (XRD), nowadays crystal structure determination by powder XRD has become popular, especially for those areas with difficulties getting high quality single crystals. Here we observed an intermediate phase Bi(2)Mn(x)Al(7-x)O(14) (x~1) during the decomposition of mullite-Bi(2)Mn(x)Al(4-x)O(9+δ) (solid solution of Bi(2)Mn(4)O(10)-Bi(2)Al(4)O(9)). As a metastable phase, it started to decompose while forming, thus no single-phase sample can be obtained. We successfully determined its structure by powder XRD from a multi-phase sample. A modified Le Bail fitting using the atomic structure information of known impurities showed a more reliable intensity extraction from a multi-phase powder XRD than that without using atomic structures for the known impurities. The charge-flipping algorithm and Monte-Carlo based simulated annealing technique were then applied to obtain the full structural model. In principle, this strategy is applicable to more complex problems, and not limited to the oxide materials. Bi(2)Mn(x)Al(7-x)O(14) possesses a mullite-related structure. There are one tetrahedral and two octahedral sites for Mn and Al, where disordering with substantial site preferences is observed. Specifically, M1O(6) and M3O(6) octahedra share edges along the c-direction with the periodicity of 1 : 2. These octahedral chains are further connected into a 3D structure through M2O(4) dimmers and Bi.     

CsTe2O(6-x): novel mixed-valence tellurium oxides with framework-deficient pyrochlore-related structure

Structures of CsTe?O(6-x) phases were investigated by single-crystal X-ray diffraction and neutron powder diffraction. Stoichiometric CsTe?O? is a mixed-valence Cs?Te??Te???O?? compound with a rhombohedral pyrochlore-type structure where there is complete order of Te?? and Te??. On heating, this compound develops significant electrical conductivity. As CsTe?O? becomes oxygen deficient above 600 °C, the rhombohedral pyrochlore-type structure is replaced by a cubic pyrochlore-type structure with disordered Te??/Te?? and oxygen vacancies. However, for CsTe?O(6-x) phases prepared at 500 °C, the observed pyrochlore-type structure has symmetry. The Te?? and O vacancies are all on chains running along the b axis, and the maximum value of x observed is about 0.3. At still higher values of x a new compound was discovered with a structure related to that reported for Rb?Te???Te???O??.     

Design of energy band alignment at the Zn(1-x)Mg(x)O/Cu(In,Ga)Se2 interface for Cd-free Cu(In,Ga)Se2 solar cells

The electronic band structure at the Zn(1-x)Mg(x)O/Cu(In(0.7)Ga(0.3))Se(2) interface was investigated for its potential application in Cd-free Cu(In,Ga)Se(2) thin film solar cells. Zn(1-x)Mg(x)O thin films with various Mg contents were grown by atomic layer deposition on Cu(In(0.7)Ga(0.3))Se(2) absorbers, which were deposited by the co-evaporation of Cu, In, Ga, and Se elemental sources. The electron emissions from the valence band and core levels were measured by a depth profile technique using X-ray and ultraviolet photoelectron spectroscopy. The valence band maximum positions are around 3.17 eV for both Zn(0.9)Mg(0.1)O and Zn(0.8)Mg(0.2)O films, while the valence band maximum value for CIGS is 0.48 eV. As a result, the valence band offset value between the bulk Zn(1-x)Mg(x)O (x = 0.1 and x = 0.2) region and the bulk CIGS region was 2.69 eV. The valence band offset value at the Zn(1-x)Mg(x)O/CIGS interface was found to be 2.55 eV after considering a small band bending in the interface region. The bandgap energy of Zn(1-x)Mg(x)O films increased from 3.25 to 3.76 eV as the Mg content increased from 0% to 25%. The combination of the valence band offset values and the bandgap energy of Zn(1-x)Mg(x)O films results in the flat (0 eV) and cliff (-0.23 eV) conduction band alignments at the Zn(0.8)Mg(0.2)O/Cu(In(0.7)Ga(0.3))Se(2) and Zn(0.9)Mg(0.1)O/Cu(In(0.7)Ga(0.3))Se(2) interfaces, respectively. The experimental results suggest that the bandgap energy of Zn(1-x)Mg(x)O films is the main factor that determines the conduction band offset at the Zn(1-x)Mg(x)O/Cu(In(0.7)Ga(0.3))Se(2) interface. Based on these results, we conclude that a Zn(1-x)Mg(x)O film with a relatively high bandgap energy is necessary to create a suitable conduction band offset at the Zn(1-x)Mg(x)O/CIGS interface to obtain a robust heterojunction. Also, ALD Zn(1-x)Mg(x)O films can be considered as a promising alternative buffer material to replace the toxic CdS for environmental safety.