Chemically selective membrane optode for Cr(VI) determination in aqueous samples

A methodology for simultaneous preconcentration and determination of Cr(VI) from aqueous samples was developed using a membrane optode formed by physical inclusion of a Cr(VI) selective chromophore 1,5-diphenylcarbazide (DPC) into a plasticized cellulose triacetate matrix. The inclusion of an anion exchanger (Aliquat-336) was found to be effective for immobilization of both DPC and Cr(VI)-DPC complex in the optode matrix itself. The proportionality in intensity of the magenta color on the optodes loaded with varying amounts of Cr(VI) suggests its potential applications for screening of Cr(VI) in aqueous samples by visual colorimetry. On loading high amounts of Cr(VI) in the membrane optode, its color changes from magenta to yellow, which indicates the possibility of using it as a threshold detector for Cr(VI). The membrane optode was optimized in terms of obtaining maximum preconcentration efficiency for Cr(VI) and subsequent stable optical response proportional to the amount of Cr(VI) in the membrane optode sample. The membrane optodes were tested for Cr(VI) determination in tap water and seawater samples. Using this optode, Cr(VI) even at levels of 13.6 ppb could be quantitatively detected. The optodes developed in the present work were found to be stable, cost effective, easy to prepare and efficient for direct preconcentration and determination of Cr(VI) in a variety of aqueous samples using spectrophotometry. However, this membrane optode is for one time use only as the reaction of Cr(VI) with DPC is irreversible.     

A sensitive optode membrane for berberine using conjugated polymer as sensing material.

A new optode membrane for the sensitive determination of berberine based on fluorescence quenching of a conjugated polymer, poly(2,5-dimethoxy-phenyldiacetylene) (PDPA), is proposed. Incorporated in a membrane composed of plasticized poly(vinyl chloride) (PVC), the conjugated polymer exhibits better stability than those small sensing molecules regarding its excellent optical properties and lipophilic characteristics. Moreover, upon the introduction of a negatively charged lipophilic additive (tetraphenylborate salt) into a PVC membrane, the optode displayed enhanced sensitivity. In addition, satisfactory analytical sensing characteristics for determining beberine were obtained in terms of the selectivity, reversibility and reproducibility with a detecting range of between 7.5 x 10(-7) mol l(-1) and 7.5 x 10(-4) mol l(-1). The optode membrane has been applied to determine berberine in commercial tablets. The results showed a good agreement with those obtained by the pharmacopoeial method.     

凯氏氮量测定的简易蒸馏装置

简易的凯氏氮蒸馏装置（如图1）,设计巧妙之处是冷凝管的使用,改善了凯氏定氮常量装置易产生倒流导致实验失败的弊端,完善了定氮技术.使定氮技术极易普及.为饲料、药品、食品等氮量的测定找到了一种简易、准确、经济的方法.并且将代替凯氏定氮方法校正其它定氮仪器,能自制,自校.     

Development of an optode membrane for high pH values

The development of an optical pH sensor for high pH values is described based on the immobilization of Aniline Blue on an optically transparent triacetylcellulose membrane. The membrane is useful for repetitive and reversible pH measurements in the pH range of 8.8-13. The relative standard deviation is about 1.6% and 2% for seven measurements of the maximum change at 579 nm from pH 9 to 10.8 and from pH 11.1 to 12.8, respectively. Other advantages of the sensor include rapid equilibration time, long term stability, reversibility, high sensitivity, freedom from interference of other cations and ease of fabrication.     

Flow-through bulk optode for the fluorimetric determination of perchlorate

A flow-through fluorescence bulk optode for the flow-injection determination of perchlorate is described. As the active constituents the optode incorporates the lipophilized pH indicator fluorescein octadecyl ester and methyl tridodecyl ammonium chloride, dissolved in a plasticized poly (vinyl) chloride membrane entrapped in a cellulose support. The optode is applied in conjunction with the flow injection technique for perchlorate determination at pH 4.5 (acetic-acetate). The sensor is readily regenerated with the pH 10.4 (TRIS) carrier solution. The analytical characteristics of this optode with respect to perchlorate response time, dynamic measurement range, reproducibility and selectivity are discussed. The proposed FI method is applied to the determination of perchlorate in waters from different sources.     

A simple device for determinations using Landolt reactions

Summary A device has been described which permits several Landolt reactions to be initiated simultaneously. All solutions remain at the same temperature, and mixing is rapid. This device improves the precision and the convenience of determinations using Landolt reactions.

---

Zusammenfassung Eine Anordnung zur gleichzeitigen Ingangsetzung mehrerer Landolt-Reaktionen wurde beschrieben. Alle Lösungen werden bei gleicher Temperatur gehalten und rasch gemischt. Dadurch wird die Genauigkeit von Analysen mit Hilfe von Landolt-Reaktionen verbessert.

     

A two-component polymeric optode membrane based on a multifunctional ionic liquid

This work details the use of a 2-component optode membrane which is capable of generating three distinct colours in the presence of Cu(2+) and Co(2+) ions. It has been found that the ionic liquid (IL) trihexyltetradecylphosphonium dicyanamide [P(6,6,6,14)][DCA] can act as plasticizer, ligand and transducer dye when used in poly(vinyl chloride) (PVC) membranes, which significantly simplifies the optode membrane cocktail. Upon exposure to an aqueous Cu(2+) solution, a yellow colour is generated within the membrane, while exposure to an aqueous Co(2+) solution generates a blue colour. Exposure to a solution containing both ions produces a green colour. Vibrational spectroscopy has been used to investigate the molecular basis of the IL-metal ion the binding mechanism. Analytical characteristics of the membranes including the effect of interfering ions, binding constants and the limit of detection for both ions have been estimated. Finally the case of simultaneous dual-analyte recognition is presented based on two distinct absorption maxima.     

A simple apparatus for the determination of mercury by amalgamation with gold

The method of Eschka for the determination of mercury by amalgamating with gold has been modified by using a simple apparatus which eliminates errors caused by loss of mercury vapour. The method does not require a skilled operator and it is suitable for routine analysis. For a sample containing 3% mercury, the estimated standard deviation is 0.06.     

Development of a new flow-through bulk optode for the determination of manganese(III)

A flow-through bulk optode based on the use of 1-(2-pyridylazo)-2-naphthol (PAN) immobilized in a plasticized poly(vinyl chloride) membrane entrapped in a cellulose support, in conjuntion with the flow injection analysis technique, is proposed for the determination of manganese(II). The calibration graph obtained at 570 nm was linear in the range 0.27-27.5 mg L(-1) (5 x 10(-6)-5 x 10(-4) M) Mn(II) with a detection limit of 0.18 mg L(-1). The coefficients of variation of the sensor response for 5.5 mg L(-1) of Mn(II) were +/-0.22% for consecutive measurements (n = 10), +/-0.48% between days (n = 5) and +/-0.38% between different membranes (n = 6). The sensor was readily regenerated with the carrier acetic acid/acetate buffer of pH 4.5. The method was applied to the determination of manganese in steels, waters and lemon tree leaves.     

Particle sorting using a porous membrane in a microfluidic device

Porous membranes have been fabricated based on the development of the perforated membrane mold [Y. Luo and R. N. Zare, Lab Chip, 2008, 8, 1688-1694] to create a single filter that contains multiple pore sizes ranging from 6.4 to 16.6 μm inside a monolithic three-dimensional poly(dimethylsiloxane) microfluidic structure. By overlapping two filters we are able to achieve smaller pore size openings (2.5 to 3.3 μm). This filter operates without any detectable irreversible clogging, which is achieved using a cross-flow placed in front of each filtration section. The utility of a particle-sorting device that contains this filter is demonstrated by separating polystyrene beads of different diameters with an efficiency greater than 99.9%. Additionally, we demonstrate the effectiveness of this particle-sorting device by separating whole blood samples into white blood cells and red blood cells with platelets.     

Development of a new flow-through bulk optode for the determination of manganese(II)

A flow-through bulk optode based on the use of 1-(2-pyridylazo)-2-naphthol (PAN) immobilized in a plasticized poly(vinyl chloride) membrane entrapped in a cellulose support, in conjuntion with the flow injection analysis technique, is proposed for the determination of manganese(II). The calibration graph obtained at 570 nm was linear in the range 0.27–27.5 mg L^–1 (5 × 10^–6– 5 × 10^–4 M) Mn(II) with a detection limit of 0.18 mg L^–1. The coefficients of variation of the sensor response for 5.5 mg L^–1 of Mn(II) were ±0.22% for consecutive measurements (n = 10), ±0.48% between days (n = 5) and ±0.38% between different membranes (n = 6). The sensor was readily regenerated with the carrier acetic acid/acetate buffer of pH 4.5. The method was applied to the determination of manganese in steels, waters and lemon tree leaves. Received: 13 December 2000 / Revised: 25 January 2001 / Accepted: 26 January 2001     

A PVC-membrane bulk optode for gallium(III) ion determination

An optical probe responsive to gallium(III) ion has been developed. The gallium sensing system was prepared by incorporating 4-(p-nitrophenyl azo)-pyrocatechol (NAP) as ionophore in a plasticized PVC membrane containing tributylphosphate (TBP) as plasticizer. The sensing membrane in contact with gallium ion at pH 3.5, changes color from yellow-brown to pink-brown. Under optimum conditions, the proposed membrane displayed a linear range of 5-83 μM with a limit of detection of 4 μM. The response time of the membrane was within 10-15 min depending on the concentration of Ga³⁺ ions. The selectivity of the probe towards gallium determination was found to be very good. Experimental results showed that the probe could be used as an effective tool in analyzing the gallium content of water samples.     

Indirect photometric detection of anions in nonaqueous capillary electrophoresis employing Orange G as probe and a light-emitting diode-based detector

A method based on indirect photometric detection (IPD) in CE employing a blue LED (473 nm) as a light source and the highly absorbing (478 nm) anionic dye, Orange G, as the probe ion was developed for the sensitive analysis of inorganic and organic anions. The use of nonaqueous solvents was examined as a simple way to reduce the adsorption of the dye onto the capillary wall and to thereby improve the baseline stability. The benefits of this approach were confirmed by experiments using BGEs in methanol (MeOH) and DMSO in which superior baselines were obtained relative to those achieved using aqueous electrolyte systems. A range of commercial LEDs was tested to improve the detection performance, with a difference of 25% in sensitivity being observed between the best and worst performing LED. The final system (4 mM Orange G, 0.05% w/v hydroxypropylcellulose (HPC), 20 mM triethanolamine (TEA) in pure MeOH) exhibited stable baselines and very low LODs (0.10-0.18 microM) for a test mixture comprising nine inorganic and organic anions. These values represent a two- to six-fold improvement over previous studies and the proposed method provides the most sensitive IPD method for the determination of anions using CE published to date. RSDs for ten replicates were in the ranges of 0.42-0.62% for migration time, 1.41-3.46% for peak area and 3.20-5.78% for peak height.     

A simple method for a determination

The a term is a primary parameter that is used to indicate the deviation of the epithermal neutron distribution in the k ₀-standardization method of neutron activation analysis, k ₀-NAA. The calculation of a using a mathematical procedure is a challenge for some researchers. The calculation of a by the "bare-triple monitor" method is possible using the dedicated commercial software KAYZERO^®/SOLCOI^®. However, when this software is not available in the laboratory it is possible to carry out the calculation of a applying a simple iterative linear regression using any spreadsheets. This approach is described in this paper. The experimental data used in the example were obtained by the irradiation of a set of suitable monitors in the NAA #1 irradiation channel of the HANARO research reactor (KAERI, Korea). The results obtained by this iterative linear regression method agree well with the results calculated by the validated mathematical method.     

Neutron activation determination of gold in rocks using dibutyl sulfide extraction for gold separation

A rapid method for the determination of gold in rocks by neutron activation was developed. The method is based on the quantitative and specific separation of gold with dialkyl sulfide extraction.     

Aptamer-based fluorometric determination of norovirus using a paper-based microfluidic device

Microchimica Acta - The authors describe a rapid and highly sensitive point-of-care device for rapid determination of noroviruses, a leading cause of acute gastroenteritis. The assay is based on...     

Development of an ethanol-selective optode membrane based on a reversible chemical recognition process

Lipophilic trifluoroacetophenone derivatives incorporated in plasticized PVC membranes are able to selectively extract water and alcohols from the sample solution into the organic membrane phase, reversibly forming hydrates and hemi-acetals, respectively. Since this is accompanied by a change in the absorption spectrum of the acetophenone isologue, the chemical recognition process can directly be translated into an optical signal. With N-acetyl-N-dodecyl-4-trifluoroacetylaniline (ETH 6022) as the electrically neutral, lipophilized carrier ethanol can be determined from 0.5 to 35% (v/v) in aqueous solutions. The calibration curve for different ethanol-water mixtures shows a good correlation with the mathematically derived formalism and thus confirms the theoretically expected behavior. Besides high reproducibility of the optical signals, very short response times of less than 30 s were realized. The optode membrane presented exhibits a preference for ethanol compared to water by a factor greater than 11. The selectivities for several primary alcohols, such as methanol, ethanol, 1-propanol and 1-n-butanol, are comparable, but isopropanol and tert.-butanol are rejected by a factor of about 10. The alcohol concentration in different beverages was determined to evaluate the reliability of the system. The values obtained for wine, beer and different spirits show an excellent correlation with those obtained by a conventional approach involving distillation and density measurements. A residual standard deviation of ± 0.27% (v/v) over the 0.7–40% (v/v) range was found.     

PDMS microfludic device for optical detection of protein immunoassay using gold nanoparticles

A simple but highly specific immunoassay system for goat anti-human IgG has been developed using gold nanoparticles and microfluidic techniques. The assay is based on the deposition of gold nanoparticles that are coated with protein antigens in the presence of their corresponding antibodies to microfluidic channel surface. The effects of time accumulation, the flow velocity, and the concentration of antibodies to the red light absorption percentage (RAP) of deposition were investigated with an ordinary optical microscope. By controlling the reaction time and flow velocity, a dynamic range of 3 orders of magnitude and a detection sensitivity of 10 ng ml(-1) of goat anti-human IgG were achieved. Because of its simplicity and flexibility, this new technique should be useful for fast, highthroughput screening of antibodies in clinical diagnostic applications.