Raman scattering characterization of vertical aligned 1D IrO2 nanocrystals grown on single crystal oxide substrates

Raman scattering (RS) has been used as a technique for characterization of IrO₂ one dimensional (1D) nanocrystals (NCs) deposited on sapphire(100) and LiNbO₃(100) substrates under various conditions. The IrO₂ NCs were grown via metalorganic chemical vapor deposition method using (MeCp)(COD)Ir as the precursor and reactive magnetron sputtering using Ir metal target. The red-shifts and asymmetric broadening of the Raman lineshape for the NCs were analyzed by a modified spatial correlation (MSC) model, which includes the factor of stress induced shift. The proposed MSC model showed that the effects of stress and nanometric size can be separated in analyzing the observed Raman features. The usefulness of the experimental RS together with the MSC model analysis as a residual stress and structural characterization technique for 1D NCs has been demonstrated.     

Effects of rapid thermal annealing on the structural properties of TiO2 nanotubes

The structural properties of TiO₂ nanotubes with rapid thermal annealing (RTA) and traditional thermal annealing in O₂ were studied by X-ray diffraction (XRD) and Raman scattering measurements. From analyzing the line width of XRD and the correlation length of the Raman peak, we demonstrate that RTA can be an effective tool for amorphous-anatase transformation in TiO₂ nanotubes. The Raman peak redshifts and reduces its line width after thermal annealing and RTA, which may involves the reduction of oxygen-related defects.     

A comparative study of microstructure of RuO2 nanorods via Raman scattering and field emission scanning electron microscopy

Raman scattering (RS) and field emission scanning electron microscopy (FESEM) have been used to extract microstructural information of RuO₂ nanorods (NRs) and a two-phase system comprising NRs embedded in polycrystalline matrix deposited on different substrates by the metal-organic chemical vapor deposition method. The red shifts and asymmetric broadening of the Raman line shape for the NRs are analyzed by the spatial correlation model. The deduced spatial correlation length l is found to be much smaller than that of the average size L₀ estimated from the FESEM images. The Raman features for the two-phase system can be resolved into two parts: a Lorentzian line shape feature corresponding to the polycrystallite at higher frequency side and an asymmetrically broadened NRs' signature located at lower frequency end. The volume fraction of NRs in the two-phase system can be determined from the analysis. These results demonstrate the significance of RS as a structural characterization method when used in conjunction with FESEM.     

Structural phase transitions and sodium ordering in Na0.5CoO2: a combined electron diffraction and Raman spectroscopy study

The nonstoichiometric Na_xCoO₂ system exhibits extraordinary physical properties that correlate with temperature and Na concentration in its layered lattice without evident long-range structure modification when conventional crystallographic techniques are applied. For instance, Na_0.7CoO₂, a thermodynamically stable phase, shows large thermoelectric power; water-intercalated Na_0.33CoO₂·1.3H₂O is a newly discovered superconductor with T_c∼4 K, and Na_0.5CoO₂ exhibits an unexpected charge ordering transition at around T_co∼55 K. Recent studies suggest that the transport and magnetic properties in the Na_xCoO₂ system strongly depend on the charge carrier density and local structural properties. Here we report a combined variable temperature transmission electron microscopy and Raman scattering investigation on structural transformations in Na_0.5CoO₂ single crystals. A series of structural phase transitions in the temperature range from 80 to 1000 K are directly identified and the observed superstructures and modulated phases can be interpreted by Na-ordering. The Raman scattering measurements reveal phase separation and a systematic evolution of active modes along with phase transitions. Our work demonstrates that the high mobility and ordering of sodium cations among the CoO₂ layers are a key factor for the presence of complex structural properties in Na_xCoO₂ materials, and also demonstrate that the combination of electron diffraction and Raman spectroscopy measurements is an efficient way for studying the cation ordering and phase transitions in related systems.     

Synthesis of ZnS nanorods by annealing precursor ZnS nanoparticles in NaCl flux

ZnS nanorods were fabricated by annealing precursor ZnS nanoparticles, which were prepared by one-step, solid-state reaction of ZnCl₂ and Na₂S through grinding by hand at ambient temperature, in NaCl flux. The as-prepared ZnS nanorods have diameters of 40-80 nm, and lengths up to several micrometers. The structural features and chemical composition of the nanorods were investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM), selected area electron diffraction (SAED), high-resolution transmission electron microscopy (HRTEM), and Raman spectra.     

Nano-star formation in Al-doped ZnO thin film deposited by dip-dry method and its characterization using atomic force microscopy, electron probe microscopy, photoluminescence and laser Raman spectroscopy

Zinc oxide doped with Al (AZO) thin films were prepared on borosilicate glass substrates by dip and dry technique using sodium zincate bath. Effects of doping on the structural and optical properties of ZnO film were investigated by XRD, EPMA, AFM, optical transmittance, PL and Raman spectroscopy. The band gap for ZnO:Al (5.0 at. wt.%) film was found to be 3.29 eV compared with 3.25 eV band gap for pure ZnO film. Doping with Al introduces aggregation of crystallites to form micro-size clusters affecting the smoothness of the film surface. Al³⁺ ion was found to promote chemisorption of oxygen into the film, which in turn affects the roughness of the sample. Six photoluminescence bands were observed at 390, 419, 449, 480, 525 and 574 nm in the emission spectra. Excitation spectra of ZnO film showed bands at 200, 217, 232 and 328 nm, whereas bands at 200, 235, 257 and 267 nm were observed for ZnO:Al film. On the basis of transitions from conduction band or deep donors (CB, Zn_i or V_OZn_i) to valence band and/or deep acceptor states (VB, V_Zn or O_i or O_Zn), a tentative model has been proposed to explain the PL spectra. Doping with Al³⁺ ions reduced the polar character of the film. This has been confirmed from laser Raman studies.     

Phonon confinement effect on nanocrystalline LiCoO2 studied with Raman spectroscopy

A systematic investigation on nanocrystalline LiCoO₂ has been carried out using Raman spectroscopy. We synthesized nanocrystalline LiCoO₂ (ca. 20-50 nm) through a combination of rapid thermal annealing at various annealing temperatures and a sol-gel method assisted with a triblock copolymer surfactant. Powder X-ray diffraction measurements revealed the formation of LiCoO₂. The crystallite size of LiCoO₂ from the Scherrer equation strongly depended on the annealing temperature. The crystallite size was confirmed by SEM and TEM measurements. Raman shifts of the A_1g and E_g modes for nanocrystalline LiCoO₂ exhibited a broadening and a frequency shift according to the crystallite size. While the frequency shift could be ascribed to a structural strain at the surface, the broadening was due to the phonon confinement effect produced by narrow crystal boundaries.     

Confined acoustic modes and spectral determination of network connectivity: Raman signatures of nanometric structure in g-GexSe1−x

Low-temperature Raman scattering results are presented on three glass compositions of Ge_xSe_1−x (15, 20, and 27 At. Ge%), and conciled with their reported structural data. The acoustic range is marked by the absence of Boson peak, and features discrete modes corresponding to nanometric dynamic aggregates. First sharp diffraction peak (FSDP) in structure factor S(k), due to Ge-Ge correlations brought about by shared Ge[Se_1/2]₄ tetrahedra medium-range structures, signifies 3D networking of Se-chains. A measure of volume-fraction of these entities determined from the FSDP area, and their number density ρ_MRS∝(k³Area)_FSDP is found to relate directly to the network connectivity, defined from optical Raman spectra in terms of the degree of cross-linking of Se-chains.     

Influence of ordering change on the optical and thermal properties of inflation polyethylene films

Changes of thermal diffusivity inside femtosecond laser-structured volumes as small as few percent were reliably determined (with standard deviation less than 1%) with miniaturized sensors. An increase of thermal diffusivity of a crystalline high-density polyethylene (HDPE) inflation films by 10-20% from the measured (1.16 ± 0.01) × 10⁻⁷ m² s⁻¹ value in regions not structured by femtosecond laser pulses is considerably larger than that of non-crystalline polymers, 0-3%. The origin of the change of thermal diffusivity are interplay between the laser induced disordering, voids’ formation, compaction, and changes in molecular orientation. It is shown that laser structuring can be used to modify thermal and optical properties. The birefringence and infrared spectroscopy with thermal imaging of CH₂ vibrations are confirming inter-relation between structural, optical, and thermal properties of the laser-structured crystalline HDPE inflation films. Birefringence modulation as high as Δn ∼ ± 1 × 10⁻³ is achieved with grating structures.     

Structural study of CoxGe100−x alloys produced by mechanical alloying

Two alloys of the Co-Ge system were produced by mechanical alloying starting from the elemental powders in the compositions Co₂₀Ge₈₀ and Co₄₀Ge₆₀. The crystalline structures of the Co_xGe_100−x (x=20, 40) alloys obtained were investigated using the X-ray diffraction (XRD) technique. The measured XRD patterns showed the presence of the peaks corresponding to the crystalline m-CoGe phase and also to the high pressure and temperature phase c-CoGe in the as-milled sample for Co₂₀Ge₈₀, although it was milled at room temperature and pressure. For Co₄₀Ge₆₀, the crystalline Co₃Ge₂ phase was obtained, and structural data for all phases were determined by means of a Rietveld refinement procedure. The thermal stability of the phases was investigated performing a heat treatment of the alloys at 450 °C for 6 h and, after that, new XRD measurements were collected and were also studied using a Rietveld refinement procedure. The m-CoGe and Co₃Ge₂ phases seem to be very stable, but the relative amount of c-CoGe decreases a little, indicating a less stable phase, which can be explained by the fact that it is produced usually under extreme conditions.     

Raman scattering and optical absorption studies of an orbital ordered Ca2RuO4

We have reported the Raman scattering and infrared absorption results on a t_2g orbital ordered Ca₂RuO₄. At 10 K, a strong and clear peak was observed in Raman scattering near 1360 cm⁻¹ with x′x′ geometry. In contrast to optic phonon modes, the peak does not show any frequency shift but rapidly decreases with increasing temperature. In addition, the peak is not observed in infrared absorption measurement. By comparing the previous Raman scattering results for several transition metal oxides, we have discussed the possible origins and ambiguities of the intriguing peak in Ca₂RuO₄.     

Pulsed laser induced synthesis of scheelite-type colloidal nanoparticles in liquid and the size distribution by nanoparticle tracking analysis

Pulsed laser ablation (PLA) of ceramic target in liquid phase was successfully employed to prepare calcium tungstate (CaWO₄) and calcium molybdate (CaMoO₄) colloidal nanoparticles. The crystalline phase, particle morphology and optical property of the colloidal nanoparticles were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and Raman spectroscopy. The produced stable colloidal suspensions consisted of the well-dispersed nanoparticles showing a spherical shape. The mechanism for the laser ablation and nanoparticle forming was discussed under consideration of photo-ablation process. Nanoparticle tracking analysis using optical microscope combined with image analysis was proposed to determine the size distribution function of the prepared colloidal nanoparticles. The mean size of the CaWO₄ and CaMoO₄ colloidal nanoparticles were 16 and 29 nm, with a standard deviations of 2.1 and 5.2 nm, respectively.     

Raman study of phase transformation of TiO2 rutile single crystal irradiated by infrared femtosecond laser

Titanium dioxide (TiO₂) rutile single crystal was irradiated by infrared femtosecond (fs) laser pulses with repetition rate of 250 kHz and phase transformation of rutile TiO₂ was observed. Micro-Raman spectra show that the intensity of E_g Raman vibrating mode of rutile phase increases and that of A_1g Raman vibrating mode decreases apparently within the ablation crater after fs laser irradiation. With increasing of irradiation time, the Raman vibrating modes of anatase phase emerged. Rutile phase of TiO₂ single crystal is partly transformed into anatase phase. The anatase phase content transformed from rutile phase increased to a constant with increasing of fs pulse laser irradiation time. The study indicates the more stable rutile phase is transformed into anatase phase by the high pressure produced by fs pulse laser irradiation.     

Structural, thermal and optical studies of mechanical alloyed Ga40Se60 mixture

A mixture of elemental Ga and Se with the nominal composition Ga₄₀Se₆₀ was submitted to the Mechanical alloying technique and their structural, thermal and optical properties were followed by X-ray diffraction, differential thermal analysis, photoacoustic spectroscopy, UV-VIS‐NIR absorbance spectroscopy and Raman spectroscopy techniques. After 10 h of milling the X-ray pattern showed monoclinic Ga₂Se₃ phase nucleation, which is in the nanometric form, and also a minority amorphous phase. The DSC results showed exothermic reactions between 430 and 720 K attributed to amorphous-crystalline phase transition and structural relaxation of Ga₂Se₃ phase. Based on this a small amount of the as-milled sample was annealed at 723 K. Its XRD pattern showed evidences of grain growth, reduction of the interfacial component, as well as, disappearance of the amorphous phase. The annealing process induced thermal diffusivity increasing, while the optical band gap energy and Raman profile remained practically unchanged.     

Phase transition in an occupationally disordered sulfate system

We have investigated the behavior of the Li_1.43Cs_0.57SO₄ single-crystal Raman spectra and dielectric permittivity as a function of temperature. It was observed that the crystal, which is an occupationally disordered system, with orthorhombic C_2v² structure at room temperature, undergoes a phase transition at 230 K. In the new phase the SO₄ tetrahedra remain in two non-equivalent sites and there is no evidence of the doubling of the unit cell.     

Fabrication of well-aligned CdS nanotubes by CVD-template method

Well-aligned CdS nanotubes have been synthesized within the nanochannels of the porous anodic alumina (PAA) membranes by pyrolyzing cadmium bis(diethyldithiocarbamate) [Cd(S₂CNEt₂)₂] at 400 °C. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) show that the CdS nanotubes are highly ordered with uniform diameter in range of 80-150 nm and the length up to tens of microns. X-ray diffraction (XRD), Raman spectrum, energy-dispersive spectroscopy (EDS) and selected-area electron diffraction (SAED) demonstrate that the nanotubes are composed of pure hexagonal phase polycrystalline CdS. The synthetic route can, in principle, be extended to fabricate other nanotubes of a wide range of semiconductors.     

Preparation of nanocone ZnO thin film and its aging effect of photoluminescence

In this work, a nanocone ZnO thin film was prepared by electron beam evaporation on a Si (1 0 0) substrate. The structural properties of the film were investigated by X-ray diffraction (XRD), atomic force microscopy and laser Raman scattering, respectively. The aging effect of the nanocone ZnO thin film was studied by photoluminescence spectra. The structural analyses show that the prepared ZnO thin film has a hexagonal wurtzite structure and is preferentially oriented along the c-axis perpendicular to the substrate surface. The photoluminescence spectra show that with the increase of aging time, the green emission of the nanocone ZnO thin film gradually decreases while the ultraviolet emission somewhat increases. The reason for this phenomenon is likely that the green-emission-related oxygen vacancies in the film are gradually filled up. The Raman scattering analyses also suggest that the intensity of the Raman peak related to oxygen vacancies in the nanocone ZnO thin film declines after the film is aged in air for a year. Therefore, the authors think the green emission is mainly connected with oxygen vacancy defects.     

Cr-doping induced ferromagnetic behavior in antiferromagnetic EuTiO3 nanoparticles

We have synthesized a series of high quality EuTi_1−xCr_xO₃ (x = 0.0, 0.02, and 0.04) nanoparticles by simple sol-gel technique. The averaged grain size of these obtained nanoparticles displays no obvious change with Cr-doping and is about 100 nm. The structural and magnetic properties of EuTi_1−xCr_xO₃ (x = 0.0, 0.02, and 0.04) samples were detailedly investigated. It is found that the G-antiferromagnetic (G-AFM) ordering of pure EuTiO₃ can be significantly modified with slight Cr-doping, and finally the ferromagnetic behavior is enhanced for EuTi_1−xCr_xO₃ system with Cr-doping.     

Titanium-induced germanium nanocones synthesized by vacuum electron-beam evaporation: growth mechanism and morphology evolution

High-vacuum electron-beam evaporation method is used for large area, metal-nucleated germanium (Ge) nanodots and nanocones on Si₃N₄/Si preparation. Nanodot and nanocone arrays with uniform size in bulk-quantity are synthesized using titanium (Ti) nanocrystals as nucleating center at 750 °C with different Ge deposition amount, respectively. The morphology evolution from nanodot to nanocone is studied by atomic force microscopy (AFM). The structure of the prepared sample is characterized by X-ray diffraction (XRD) and Raman scattering. Ge nanocones formed by this convenient fabrication process could have potential applications on nanoelectronics and vacuum electron field emission.     

Modifications in structural and optical properties of Mn-ion implanted CdS thin films

In this paper, we report on modifications in structural and optical properties of CdS thin films due to 190 keV Mn-ion implantation at 573 K. Mn-ion implantation induces disorder in the lattice, but does not lead to the formation of any secondary phase, either in the form of metallic clusters or impurity complexes. The optical band gap was found to decrease with increasing ion fluence. This is explained on the basis of band tailing due to the creation of localized energy states generated by structural disorder. Enhancement in the Raman scattering intensity has been attributed to the enhancement in the surface roughness due to increasing ion fluence. Mn-doped samples exhibit a new band in their photoluminescence spectra at 2.22 eV, which originates from the d-d (⁴T₁ → ⁶A₁) transition of tetrahedrally coordinated Mn²⁺ ions.