Spin-engineering in the Co75Fe25/Cu(1 1 0) system

We present results on the growth and magnetic anisotropies of Co₇₅Fe₂₅ films grown on a Cu(1 1 0) single crystal. Angular dependent MOKE measurements show a thickness dependent, in-plane rotation of the easy axis of magnetisation of up to 60° from the [0 0 1] direction (towards [−1 1 0]). For a film thickness of 5 ML, just greater than that required for the onset of ferromagnetism, uniaxial anisotropy is observed with the easy axis along the [0 0 1] direction. As the film thickness increases this is seen to rotate in-plane towards the [−1 1 0] direction as the contribution from the cubic anisotropy constant grows. At a film thickness of 9 ML there is predominantly cubic anisotropy and at 10 ML the easy axis is rotated to 150° with respect to the [1 −1 0] axis, where it is stabilised.     

Atomic structure and tip-induced reconstruction of bromide covered Cu(1 1 0) electrodes

The behavior of specifically adsorbed bromide on Cu(1 1 0) in 10 mM HBr has been studied using cyclic voltammetry in combination with high resolution in situ electrochemical scanning tunneling microscopy (EC-STM).At cathodic potentials near the onset of the hydrogen evolution reaction the structure of the bare copper surface was observed by EC-STM. A variation of the electrode potential in positive direction causes a specific anion adsorption leading to the formation of a highly ordered superstructure with a quasi-hexagonal symmetry. The two-dimensional lattice of this adlayer can be described by a c(3 × 2) unit cell. The bromide anions are arranged parallel to the close packed copper rows and are located in three different types of adsorption sites. These inequivalently bound bromide species are imaged with different brightness in the STM-pictures. As a result the bromide adlayer exhibits a long-ranged wavy superstructure superimposed on the atomic corrugation.Tip induced copper corrosion is used to obtain highly ordered nanostructures due to a locally confined electrochemical annealing process proceeding along the [0 0 1]-direction of the substrate. This annealing process results in the formation of Cu(1 0 0)-facets.     

First-principles study of oxygenated diamond (0 0 1) surfaces with and without hydrogen

The structural characterization of oxygenated diamond (0 0 1) surface with and without H-presence has been investigated by the density-functional theory within the generalized gradient approximation and the plane-wave pseudopotential method. It is shown that, without the H, the O-bridge site has lower energy than the O-on-top site for both half and fully monolayer (ML) oxygen coverage. For hydrogenated diamond (0 0 1) surfaces, we found for half ML O coverage, a more stable (2 × 2):0.5H&0.5(OH) phase than the previously reported (2 × 1):0.5H&0.5(OH) phase [H. Tamura, H. Zhou, K. Sugisako, Y. Yokoi, S. Takami, M. Kubo, K. Teraishi, A. Miyamoto, A. Imamura, M.N. Gamo, T. Ando, Phys. Rev. B 61 (2000) 11025]. Furthermore, at one ML O coverage, a (2 × 2):(OH) phase is the most stable structure than the previously reported (2 × 1):(OH) phase. With the increase of the (OH) coverage, the importance of the hydrogen bonds increases in terms of stabilizing these structures.     

Structure and homoepitaxial growth of GaAs(6 3 1)

We have studied the surface atomic structure of GaAs(6 3 1), and the GaAs growth by molecular beam epitaxy (MBE) on this plane. After the oxide desorption process at 585 °C reflection high-energy electron diffraction (RHEED) showed along the [−1 2 0] direction a 2× surface reconstruction for GaAs(6 3 1)A, and a 1× pattern was observed for GaAs(6 3 1)B. By annealing the substrates for 60 min, we observed that on the A surface appeared small hilly-like features, while on GaAs(6 3 1)B surface pits were formed. For GaAs(6 3 1)A, 500 nm-thick GaAs layers were grown at 585 °C. The atomic force microscopy (AFM) images at the end of growth showed the self-formation of nanoscale structures with a pyramidal shape enlarged along the [5−9−3] direction. Transversal views of the bulk-truncated GaAs(6 3 1) surface model showed arrays of atomic grooves along this direction, which could influence the formation of the pyramidal structures.     

In situ oxidation study of MgO(1 0 0) supported Pd nanoparticles

We have investigated the oxidation behavior of Pd nanoparticles grown epitaxially on MgO(1 0 0) single crystal substrates. We find that the interaction of oxygen with octahedral Pd nanoparticles at 500 K can be subdivided in three stages: above 10⁻⁶ mbar O₂ pressure, the particles start to flatten; above 10⁻³ mbar, the particles begin to shrink laterally and to be less truncated at the corners. The formation of epitaxial bulk PdO sets in at oxygen pressures above 0.1 mbar, which is accompanied by a continuous shrinkage of the Pd particles. Our results point to a novel nanoparticle oxidation mechanism: the Pd particles act as dissociation centers for O₂ and serve at the same time as source for Pd atoms resulting in epitaxial PdO growth on MgO(1 0 0).     

Study of vacancy on diamond (1 0 0) (2 × 1) surface from first-principles

Structure and energy related properties of neutral and charged vacancies on relaxed diamond (1 0 0) (2 × 1) surface were investigated by means of density functional theory. Calculations indicate that the diffusion of a single vacancy from the top surface layer to the second layer is not energetically favored. Analysis of energies in charged system shows that neutral state is most stable on diamond (1 0 0) (2 × 1) surface. The multiplicity of possible states can exist on diamond (1 0 0) surface in dependence on the surface Fermi level, which supports that surface diffusion of a vacancy is mediated by the change of vacancy charge states. Analysis of density of states shows surface vacancy can be effectively measured by photoelectricity technology.     

The magnetic map of NiMn alloy thin films on Co(0 0 1) and Co(1 1 1)

Following the experimental work of Groudeva-Zotova et al. [S. Groudeva-Zotova, D. Elefant, R. Kaltofen, D. Tietjen, J. Thomas, V. Hoffmann, C.M. Schneider, J. Magn. Magn. Mater. 263 (2003) 57] where the magnetic and structural characteristics of a bi-layer NiMn-Co exchange biasing systems was investigated, density functional calculations with generalized gradient corrections were performed on (Mn_0.5Ni_0.5)_n ordered alloy on Co(0 0 1) and one Mn_1−xNi_x monolayer on Co(1 1 1). For the Mn_0.5Ni_0.5 monolayer on Co(0 0 1), magnetic moments per surface atom of 0.65 μ_B and 3.76 μ_B were obtained for Ni and Mn, respectively. Those magnetic moments are aligned parallel to the total moment of Co(0 0 1). A complex behavior of the Mn moment in dependence of the thickness “n” is obtained for (Mn_0.5Ni_0.5)_n on Co(0 0 1). Investigations on Mn_1−xNi_x monolayer on Co(1 1 1) have shown that the crystallographic orientation does not modify significantly neither the magnetic moments of Mn and Ni atoms nor their ferromagnetic coupling with the Co(1 1 1) substrate, except for x = 0.66. For x = 0.66 the Mn sub-lattice presents an antiferromagnetic coupling leading to a quenching of the Ni magnetic moment.     

Dynamics of copper atoms on Si(1 1 1)-7 × 7 surfaces

This study investigated the dynamics of copper atoms adsorbed on Si(1 1 1)-7 × 7 surfaces between 300 K and 623 K using a variable-temperature scanning tunneling microscope (STM). The diffusion behavior of copper clusters containing up to ∼6 atoms into a particular half unit cell of the 7 × 7 reconstructed Si(1 1 1) surface was considered. The movements and the formation of copper clusters were tracked in detail. The activation energies and pre-exponential factors for various diffusion paths were estimated. Finally, the Cu-etching-Si process and the quasi-5 × 5 incommensurated phase of Cu/Si islands were discussed.     

High resolution analysis of the rotational levels of the (0 0 0), (0 1 0), (1 0 0), (0 0 1), (0 2 0), (1 1 0) and (0 1 1) vibrational states of SO2

A high resolution (0.0018 cm⁻¹) Fourier transform instrument has been used to record the spectrum of an enriched ³⁴S (95.3%) sample of sulfur dioxide. A thorough analysis of the ν₂, 2ν₂ − ν₂, ν₁, ν₁ + ν₂ − ν₂, ν₃, ν₂ + ν₃ − ν₂, ν₁ + ν₂ and ν₂ + ν₃ bands has been carried out leading to a large set of assigned lines. From these lines ground state combination differences were obtained and fit together with the existing microwave, millimeter, and terahertz rotational lines. An improved set of ground state rotational constants were obtained. Next, the upper state rotational levels were fit. For the (0 1 0), (1 1 0) and (0 1 1) states, a simple Watson-type Hamiltonian sufficed. However, it was necessary to include explicitly interacting terms in the Hamiltonian matrix in order to fit the rotational levels of the (0 2 0), (1 0 0) and (1 0 1) states to within their experimental accuracy. More explicitly, it was necessary to use a ΔK = 2 term to model the Fermi interaction between the (0 2 0) and (1 0 0) levels and a ΔK = 3 term to model the Coriolis interaction between the (1 0 0) and (0 0 1) levels. Precise Hamiltonian constants were derived for the (0 0 0), (0 1 0), (1 0 0), (0 0 1), (0 2 0), (1 1 0) and (0 1 1) vibrational states.     

Olefin bonding mechanism and growth to (1 0 0)(2 × 1):H diamond

The bonding and growth mechanism of photochemically attached olefin molecules to (1 0 0)(2 × 1):H diamond is characterized using atomic force (AFM) and scanning tunneling microscopy (STM) experiments in combination with molecular orbital calculations. To identify growth schemas, diamond surfaces after 10, 40 and 90 min of photo-chemically stimulated growth have been characterized. These data show clearly island formation which is discussed taking into account a growth model from silicon. The island growth shows no directional properties which are attributed to arrangement and geometrical properties of hydrogen terminated carbon bonds at the surface of (1 0 0) oriented (2 × 1) reconstructed diamond.     

Fourfold in-plane magnetic anisotropy in epitaxial Fe(1 1 0)/Cu(0 0 1) and Fe(1 1 0)/Ni(0 0 1) bilayers

Epitaxial Fe(1 1 0) films with thicknesses of 100-800 nm on Cu(0 0 1) and Ni(0 0 1) buffer layers grown on MgO(0 0 1) substrates have been fabricated. These films contain Fe(1 1 0) crystallites which are in the Pitsch orientation relationship. Magnetization and the fourfold in-plane magnetic anisotropy constants of these films have been determined by torque measurements. All the samples under study are characterized by a fourfold magnetic anisotropy with easy axes parallel to the [1 0 0] and [0 1 0] directions of Cu(0 0 1) and Ni(0 0 1) layers. The measured values of the constant for Fe(1 1 0)/Cu(0 0 1) are found to depend on deposition temperature; a maximum value of (2.5±0.1)×10⁵ erg/cm³ is reached after annealing at 600 °С. The in-plane torque measurements on Fe(1 1 0)/Ni(0 0 1) bilayers obtained at 300 °С, on the other hand, exhibit a constant value of (2.7±0.1)×10⁵ erg/cm³. Assuming an exchange interaction between the Fe(1 1 0) crystallites, which are in the Pitsch orientation relationship, the fourfold in-plane magnetic anisotropy has been calculated as 2.8×10⁵ erg/cm³. The deviations of the experimental values from the predicted one may be explained by the formation of a polycrystalline phase within the Fe(1 1 0) layer and a partial disorientation of the epitaxial crystallites.     

Initial stages of the autocatalytic oxidation of the InAs(0 0 1)-(4 × 2)/c(8 × 2) surface by molecular oxygen

The initial stages of oxidation of the In-rich InAs(0 0 1)-(4 × 2)/c(8 × 2) surface by molecular oxygen (O₂) were studied using scanning tunneling microscopy (STM) and density functional theory (DFT). It was shown that the O₂ dissociatively chemisorbs along the rows in the [1 1 0] direction on the InAs surface either by displacing the row-edge As atoms or by inserting between In atoms on the rows. The dissociative chemisorption is consistent with being autocatalytic: there is a high tendency to form oxygen chemisorption sites which grow in length along the rows in the [1 1 0] direction at preexisting oxygen chemisorption sites. The most common site size is about 21-24 Å in length at ∼25% ML coverage, representing 2-3 unit cell lengths in the [1 1 0] direction (the length of ∼5-6 In atoms on the row). The autocatalysis was confirmed by modeling the site distribution as non-Poisson. The autocatalysis and the low sticking probability (∼10⁻⁴) of O₂ on the InAs(0 0 1)-(4 × 2)/c(8 × 2) are consistent with activated dissociative chemisorption. The results show that is it critical to protect the InAs surface from oxygen during subsequent atomic layer deposition (ALD) or molecular beam epitaxy (MBE) oxide growth since oxygen will displace As atoms.     

Surface resonance transition of roughened Cu(1 1 0)

The temperature dependence of the reflection anisotropy spectroscopy (RAS) of a Cu(1 1 0) surface has been studied over the temperature range 700-1000 K. Because of the roughening transition at 900 K, the bimodal feature at 4.2 eV for a clean surface shifted to 4.3 eV on annealing. A significant decrease in intensity of the same energy level was also observed with increasing annealing temperature. In the annealing temperature range 700-1000 K, anharmonic behavior is expected to be the predominant process of atomic disordering at the surface. Changes in the RAS of Cu(1 1 0) as a result of thermal processing can be understood in terms of the associated changes in surface states. The RAS signal for a surface resonance transition at 4.2 eV is associated with monoatomic [0 0 1] steps.     

Characteristic energy band values and electron attenuation length of a chemical-vapor-deposition diamond (0 0 1)2 × 1 surface

The characteristic energy band values such as the Fermi-level position with respect to valence band top for a boron-doped p-type hydrogen-terminated chemical-vapor-deposition (CVD) diamond (0 0 1)2 × 1 surface and for a clean CVD diamond (0 0 1)2 × 1 surface have been determined by a new method with an accuracy of ±0.02 eV. The electron attenuation length for the clean diamond (0 0 1)2 × 1 surface for the electron kinetic energy of C 1s X-ray photoemission peak by Mg Kα excitation is experimentally determined to be 2.1-2.2 nm. These values are compared and discussed with the previously reported experimental and simulation values.     

Ge(5 × 5) as a wetting layer on Si(1 1 1)

Ab initio total energy methods are used to investigate the effects on a Ge(1 1 1)-5 × 5 surface of the lateral compressive stress that would be due to a Si substrate, and the effects of intermixing at the interface with the substrate. The effects of stress due to the lattice mismatch between Si and Ge are studied on a Ge slab by changing the lattice constant in the surface plane from that of experimental bulk diamond Ge to that of Si. When this is done the height difference of the Ge adatoms in the faulted half-cell from those in the unfaulted half is accentuated. Effects on the Ge surface due to the presence of the Si-Ge interface were studied using a thin Ge layer on a Si substrate. The presence of the substrate leads to corrugations with significant height differences appearing among the faulted adatoms. The energetics of intermixing were investigated for Si-Ge single atom interchanges. Additional corrugations resulted from the shortened bondlengths due to the Si impurity in the wetting layer.     

Study of ammonia molecule adsorbing on diamond (1 0 0) surface

The diamond (1 0 0) surface with amino terminations is investigated based on density function theory within the generalized gradient approximation. Our calculated negative electron affinity of diamond (1 0 0) surface with hydrogen termination provides a necessary condition for initiating radical reaction. The results display that the ammonia molecule can form stable C-N covalent bonds on the diamond surface. In addition, due to the lower adsorption energy of one amino group binding on diamond surface, single amino group (SAG) model is easy to be realized in experiment with the comparison of double amino group (DAG) model. The adsorbed ammonia molecule will induce acceptor-like gap states with little change of the valence and conduction band of diamond in SAG model. The adsorption mechanism in the formation of ammonia monolayer on H-terminated diamond (1 0 0) surface, and two possible adsorption structures (SAG and DAG) were especially studied.     

Lattice-resolution imaging of the sapphire (0 0 0 1) surface in air by AFM

Lattice-resolution images of single-crystal α-alumina (sapphire) (0 0 0 1) surfaces have been obtained using contact-mode AFM under ambient conditions. It was found that the hexagonal surface lattice has a periodicity of 0.47 ± 0.11 nm, which is identical to that reported previously when the same surface was imaged in water. Large lattice corrugations (as high as 1 nm) were observed, but were concluded to be imaging artifacts because of the strong friction which causes additional deflection of the cantilever. The additional deflection of the cantilever is registered by the detector of the optical beam-deflection AFM resulting in an overestimation of the height at each lattice point. Abrupt changes were also resolved in the topography including honeycomb patterns and a transition from 2D lattices to 1D parallel stripes, with scanning direction. These phenomena can be explained by the commensurate sliding between the tip and sapphire surface due to the strong contact force.     

Long range one-dimensional ordering of lead phthalocyanine monolayer on InSb(1 0 0) (4 × 2)/c(8 × 2)

Sub-monolayer and monolayer of lead phthalocyanine deposited on InSb(1 0 0) (4 × 2)/c(8 × 2) surface have been investigated by scanning tunneling microscopy and low energy electron diffraction. Molecules first adsorb on the indium rows of the (4 × 2)/c(8 × 2) structure in the [1 1 0] direction and diffuse at the surface in order to form two-dimensional islands. The molecule-substrate interaction stabilizes the PbPc molecules on the In rows. It weakens the interaction between molecules located in adjacent rows resulting in numerous gliding planes between the molecular chains, in the direction parallel to the rows. At monolayer completion, a long-range one-dimensional order is adopted by the molecules in the [1 1 0] direction.     

Self-regulated Ni cluster formation on the TiO2(1 1 0) terrace studied using scanning tunneling microscopy

We have studied the growth mode and morphology of Ni clusters on a TiO₂(1 1 0) surface with a wide terrace using scanning tunneling microscopy (STM) at a low coverage (less than 3 atoms nm⁻²). The Ni clusters are formed on the terrace at the low coverage of 0.2 atoms nm⁻². Their average dimensions are constant in three directions up to 1 atoms nm⁻². The Ni clusters have an oval shape with average sizes of 1.8 nm (along [0 0 1]) × 1.4 nm (along (in the [1 1 0] directions). Above the coverage of 1.0 atoms nm⁻², an increase in the cluster height occurs, retaining an almost constant lateral size. It is proposed that the interaction of the Ni cluster and the support surface regulates the Ni cluster size.     

The stability of fcc (1 1 1) metal surfaces

The results of a theoretical study on the stability of fcc (1 1 1) metal surfaces to certain commensurate-incommensurate reconstructive phase transformations is presented. Specifically, we have performed computer simulation studies of the 22×√3 surface reconstruction of Au(1 1 1). This reconstruction involves a uniaxial contraction of the top monolayer corresponding to a surface strain of about 4.3% and has been observed to be the stable structure for the clean surface at low temperatures. The driving force for the reconstruction has been associated with the quantity (f−γ), where f is the surface stress and γ is the surface free energy, while the opposing force is due to the disregistry with the underlying lattice. A continuum model yields a stability criterion that depends on the knowledge of a small number of physical quantities: f, γ, the equilibrium nearest-neighbor spacing r₁ and the shear modulus G. We have performed molecular dynamics simulations as a general stability analysis of these types of reconstructions. The results are in excellent agreement with the continuum model. The simulations using embedded-atom method potentials also accurately reproduce many observed features of the reconstruction on Au(1 1 1).