Laser fluence, repetition rate and pulse duration effects on paint ablation

The efficiency (mm³/(J pulse)) of laser ablation of paint was investigated with nanosecond pulsed Nd:YAG lasers (λ = 532 nm) as a function of the following laser beam parameters: pulse repetition rate (1-10,000 Hz), laser fluence (0.1-5 J/cm²) and pulse duration (5 ns and 100 ns). In our study, the best ablation efficiency (η ≅ 0.3 mm³/J) was obtained with the highest repetition rate (10 kHz) at the fluence F = 1.5 J/cm². This ablation efficiency can be associated with heat accumulation at high repetition rate, which leads to the ablation threshold decrease. Despite the low thermal diffusivity and the low optical absorption of the paint (thermal confinement regime), the ablation threshold fluence was found to depend on the pulse duration. At high laser fluence, the ablation efficiency was lower for 5 ns pulse duration than for the one of 100 ns. This difference in efficiency is probably due to a high absorption of the laser beam by the ejected matter or the plasma at high laser intensity. Accumulation of particles at high repetition rate laser ablation and surface shielding was studied by high speed imaging.     

Femtosecond laser ablation of silver foil with single and double pulses

The average ablation depth per pulse of silver foil by 130 fs laser pulses has been measured in vacuum over a range of three orders of magnitude of pulse fluence up to 900 J cm⁻². In addition, double pulses with separations up to 3.4 ns have been used to probe time scales of relevance for femtosecond ablation. The double pulse ablation depth, when each pulse fluence is 0.7 J cm⁻², falls to that of a single pulse as the pulse separation is increased from 0 ps to 700 ps. This time scale decreases to only 4 ps as the fluence is increased to 11 J cm⁻². It then jumps to 500 ps across a transition fluence where the slope of the ablation depth versus logarithmic fluence characteristic changes abruptly to a higher value. In addition, for pulse separations near 1000 ps, the second pulse can cause re-deposition of ejecta from the first pulse resulting in a double pulse ablation depth only 40% that of the first pulse alone. This has important implications for the interpretation of double pulse femto-LIBS intensities. Our results suggest that the optical properties of nano or mesoparticles play a significant role in double pulse ablation with large pulse separations.     

Studies of craters’ dimension for long-pulse laser ablation of metal targets at various experimental conditions

Long pulse laser shots of the PALS iodine laser in Prague have been used to obtain metal target ablation at various experimental conditions. Attention is paid mainly to the dependencies of the crater diameter on the position of minimum laser-focus spot with regard to the target surface, by using different laser wavelengths and laser energies. Not only a single one, but two minima, independently of the wavelength, of the target irradiation angle and of the target material, were recorded. Significant asymmetries, ascribed to the non-linear effects of intense laser beam with pre-formed plasma, were found, too. Estimations of ejected mass per laser pulse are reported and used to calculate the efficiency of laser-driven loading. Results on metal target ablation and crater formation at high intensities (from 2 × 10¹³ to 3 × 10¹⁶ W/cm²) are presented and compared. Crater depth, crater diameter and etching yield are reported versus the laser energy, in order to evaluate the ablation threshold fluence.     

Femtosecond laser micromilling of Si wafers

Femtosecond laser micromilling of silicon is investigated using a regeneratively amplified 775 nm Ti:Sapphire laser with a pulse duration of 150 fs operating at 1 kHz repetition rate. The morphological observation and topological analysis of craters fabricated by single-shot laser irradiation indicated that the material removal is thermal in nature and there are two distinct ablation regimes of low fluence and higher fluence with logarithmical relations between the ablation depth and the laser fluence. Crater patterns were categorized into four characteristic groups and their formation mechanisms were investigated. Femtosecond laser micromilling of pockets in silicon was performed. The effect of process parameters such as pulse energy, translation speed, and the number of passes on the material removal rate and the formation of cone-shaped microstructures were investigated. The results indicate that the microstructuring mechanism has a strong dependence on the polarization, the number of passes and laser fluence. The optimal laser fluence range for Si micromilling was found to be 2-8 J/cm² and the milling efficiency attains its maximum between 10 and 20 J/cm².     

Analyses of surface coloration on TiO2 film irradiated with excimer laser

TiO₂ film of around 850 nm in thickness was deposited on a soda-lime glass by PVD sputtering and irradiated using one pulse of krypton-fluorine (KrF) excimer laser (wavelength of 248 nm and pulse duration of 25 ns) with varying fluence. The color of the irradiated area became darker with increasing laser fluence. Irradiated surfaces were characterized using optical microscopy, scanning electron microscopy, Raman spectroscopy and atomic force microscopy. Surface undergoes thermal annealing at low laser fluence of 400 and 590 mJ/cm². Microcracks at medium laser fluence of 1000 mJ/cm² are attributed to surface melting and solidification. Hydrodynamic ablation is proposed to explain the formation of micropores and networks at higher laser fluence of 1100 and 1200 mJ/cm². The darkening effect is explained in terms of trapping of light in the surface defects formed rather than anatase to rutile phase transformation as reported by others. Controlled darkening of TiO₂ film might be used for adjustable filters.     

Microstructuring of fused silica by laser-induced backside wet etching using picosecond laser pulses

The laser-induced backside wet etching (LIBWE) is an advanced laser processing method used for structuring transparent materials. LIBWE with nanosecond laser pulses has been successfully demonstrated for various materials, e.g. oxides (fused silica, sapphire) or fluorides (CaF₂, MgF₂), and applied for the fabrication of microstructures. In the present study, LIBWE of fused silica with mode-locked picosecond (t_p = 10 ps) lasers at UV wavelengths (λ₁ = 355 nm and λ₂ = 266 nm) using a (pyrene) toluene solution was demonstrated for the first time. The influence of the experimental parameters, such as laser fluence, pulse number, and absorbing liquid, on the etch rate and the resulting surface morphology were investigated. The etch rate grew linearly with the laser fluence in the low and in the high fluence range with different slopes. Incubation at low pulse numbers as well as a nearly constant etch rate after a specific pulse number for example were observed. Additionally, the etch rate depended on the absorbing liquid used; whereas the higher absorption of the admixture of pyrene in the used toluene enhances the etch rate and decreases the threshold fluence. With a λ₁ = 266 nm laser set-up, an exceptionally smooth surface in the etch pits was achieved. For both wavelengths (λ₁ = 266 nm and λ₂ = 355 nm), LIPSS (laser-induced periodic surface structures) formation was observed, especially at laser fluences near the thresholds of 170 and 120 mJ/cm², respectively.     

Small size TiO2 nanoparticles prepared by laser ablation in water

Titanium dioxide nanoparticles in distilled H₂O solvent were prepared by laser ablation. The experiments were performed irradiating a Ti target with a second harmonic (532 nm) output of a Nd:YAG laser varying the operative fluence between 1 and 10 J cm⁻² and for an ablation time ranging from 10 to 30 min. Electron microscopy measurements have evidenced the predominant presence of nanoparticles with diameter smaller than 10 nm together with agglomerations of 100-200 nm whose content increases with the laser fluence. At low laser fluence the particles’ size distribution shows that more than 85% of the nanoparticles have a size smaller than 5 nm while at mid and high fluences the presence of 5-7 nm nanoparticles is predominant. XPS analysis has revealed the presence of different titanium suboxide phases with the prevalence of Ti-O bonds from TiO₂ species. The optical bandgap values, determined by UV-vis absorption measurements, are compatible with the anatase phase.     

Effect of pulse width and fluence of femtosecond laser on the size of nanobump array

Conical nanobump arrays were generated on gold thin film processed by interfering femtosecond laser. The transition of the height and diameter as functions of fluence and pulse width was investigated. When the fluence was 87 mJ/cm², the height and diameter were not so different at 350 fs or shorter pulse width. They decreased at longer pulse width, and no bump could be generated over 1.6 ps. The results suggest the decrease of size is due to the diffusion of electron to not-excited region, and due to heat conduction to not heated region or substrate, or change of absorbance of laser. At long pulse width of 2.4 ps and relatively higher fluence of 190 mJ/cm², nanobump had liquid-like structure as a stop motion of a water drop.     

Single-pulse drilling study on Au,Al and Ti alloy by using a picosecond laser

Picosecond laser single pulse ablation of Au, Al and Ti alloy (Ti6Al4V) was experimentally investigated with a laser pulse width of 10 ps at a wavelength of 1064 nm for potential industrial micromachining applications. The diameters, depths and morphologies of the drilled craters were studied. Two novel phenomena were found: as hole diameters decreased with fluence, a change of slope of the trend line indicated a change in ablation mechanism for Al and Ti alloy, metallic materials with short electron-phonon coupling times (<10 ps), while Au showed no such transition: an isolated island structure was also observed on Au due to significant melt expulsion. A one-dimensional two-temperature model has been used to discriminate different ablation phenomena. It is shown that metallic materials with different electron–phonon coupling constant have different ablation characteristics in the ps regime. This study could be very helpful for metallic material micromachining with high repetition rate ps lasers pulses which indicates that high throughput may be achieved as well as good machining quality.     

Influence of surface effects on the performance of lead-niobium-germanate optical waveguides

Lead-niobium-germanate planar waveguides have been produced by pulsed laser deposition. The composition of the waveguides is found to be relatively weakly dependent on the laser fluence, while their surface morphology is affected dramatically. Smooth surfaces are obtained for a narrow fluence range centered at 2.0 J/cm², while particulates having typical diameters of <0.5 μm or droplets with typical diameters of <10 μm are observed at lower and higher fluences, respectively. The refractive index of the waveguides increases with fluence up to 2.1 at 2.0 J/cm², which is close to the value of the bulk glass, and remains constant at higher fluences. Propagation losses show instead a minimum (≈6.5 dB/cm) at 2.0 J/cm². The characteristics of the ablation process that leads to the ejection of solid particulates or molten droplets as well as the increase of the waveguides density on increasing the fluence are discussed to be responsible for the observed optical behavior.     

Patterning of indium-tin oxide on glass with picosecond lasers

The results of patterning of the indium-tin oxide (ITO) film on the glass substrate with high repetition rate picosecond lasers at various wavelengths are presented. Laser radiation initiated the ablation of the material, forming grooves in ITO. Profile of the grooves was analyzed with a phase contrast optical microscope, a stylus type profiler, scanning electron microscope (SEM) and atomic force microscope (AFM). Clean removal of the ITO film was achieved with the 266 nm radiation when laser fluence was above the threshold at 0.20 J/cm², while for the 355 nm radiation, the threshold was higher, above 0.46 J/cm². The glass substrate was damaged in the area where the fluence was higher than 1.55 J/cm². The 532 nm radiation allowed getting well defined grooves, but a lot of residues in the form of dust were generated on the surface. UV radiation with the 266 nm wavelength provided the widest working window for ITO ablation without damage of the substrate. Use of UV laser radiation with fluences close to the ablation threshold made it possible to minimize surface contamination and the recast ridge formation during the process.     

Characterization of Ag and Au nanoparticles created by nanosecond pulsed laser ablation in double distilled water

Pulsed laser ablation of Ag and Au targets, immersed in double-distilled water is used to synthesize metallic nanoparticles (NPs). The targets are irradiated for 20 min by laser pulses at different wavelengths—the fundamental and the second harmonic (SHG) (λ = 1064 and 532 nm, respectively) of a Nd:YAG laser system. The ablation process is performed at a repetition rate of 10 Hz and with pulse duration of 15 ns. Two boundary values of the laser fluence for each wavelength under the experimental conditions chosen were used—it varied from several J/cm² to tens of J/cm². Only as-prepared samples were measured not later than two hours after fabrication. The NPs shape and size distribution were evaluated from transmission electron microscopy (TEM) images. The suspensions obtained were investigated by optical transmission spectroscopy in the near UV and in the visible region in order to get information about these parameters. Spherical shape of the NPs at the low laser fluence and appearance of aggregation and building of nanowires at the SHG and high laser fluence was seen. Dependence of the mean particle size at the SHG on the laser fluence was established. Comments on the results obtained have been also presented.     

XPS studies of short pulse laser interaction with copper

The effect of laser ablation on copper foil irradiated by a short 30 ns laser pulse was investigated by X-ray photoelectron spectroscopy. The laser fluence was varied from 8 to 16.5 J/cm² and the velocity of the laser beam from 10 to 100 mm/s. This range of laser fluence is characterized by a different intensity of laser ablation. The experiments were done in two kinds of ambient atmosphere: air and argon jet gas.The chemical state and composition of the irradiated copper surface were determined using the modified Auger parameter (α′) and O/Cu intensity ratio. The ablation atmosphere was found to influence the size and chemical state of the copper particles deposited from the vapor plume. During irradiation in air atmosphere the copper nanoparticles react with oxygen and water vapor from the air and are deposited in the form of a CuO and Cu(OH)₂ thin film. In argon atmosphere the processed copper surface is oxidized after exposure to air.     

Laser heating and ablation at high repetition rate in thermal confinement regime

Laser heating and ablation of materials with low absorption and thermal conductivity (paint and cement) were under experimental and theoretical investigations. The experiments were made with a high repetition rate Q-switched Nd:YAG laser (10 kHz, 90 ns pulse duration and λ = 532 nm). High repetition rate laser heating resulted in pulse per pulse heat accumulation. A theoretical model of laser heating was developed and demonstrated a good agreement between the experimental temperatures measured with the infrared pyrometer and the calculated ones. With the fixed wavelength and laser pulse duration, the ablation threshold fluence of paint was found to depend on the repetition rate and the number of applied pulses. With a high repetition rate, the threshold fluence decreased significantly when the number of applied pulses was increasing. The experimentally obtained thresholds were well described by the developed theoretical model. Some specific features of paint heating and ablation with high repetition rate lasers are discussed.     

Effects of laser operating parameters on metals micromachining with ultrafast lasers

180 femtoseconds (1 kHz) and 10 picoseconds (1-50 kHz) ultrafast laser micro-structuring of the metals Ti alloy, Al and Cu have been studied for the purpose of industrial application. The effects of some key laser operating parameters were investigated. The evolution of surface morphology revealed that laser pulses overlap in a range around the spatial FWHM can help to achieve optimal residual surface roughness. While observed ablation rate (unit: μm³ per pulse) changed dramatically with repetition rate due to the combined effects of plasma absorption, residual thermal energy and phase transition, higher throughput can be achieved with higher repetition rate. This study also indicated that residual surface roughness is almost independent of repetition rate at 10 ps temporal pulse length. The ablation depth is approximately proportional to the number of overscan; however, machining accuracy deteriorates, especially for femtosecond laser processing and metals with low thermal conductivity and short electron-phonon coupling time.     

Steady-state mechanism for polymer ablation by a free-running Er:YAG laser

A free-running Er:YAG laser is used to ablate polyethylene glycol and the ablation yield is studied as a function of molecular weight (1000-10,000 g/mol) and laser fluence (8-25 J/cm²). A steady-state ablation mechanism is proposed which includes recoil-induced expulsion as the primary contributor to the ablation yield. It is also proposed that the formation of a molten layer is a necessary part of the ablation mechanism because the calculated tensile strengths for the solid polymer are too large to permit fracture of the target due to the laser-induced stress transient. The ablation yield is found to depend in a sigmoidal fashion upon laser fluence, thus implying a variable ablation enthalpy. Finally, the current results are compared with that obtained previously with a free electron laser.     

Generation of nanospikes via laser ablation of metals in liquid environment and their activity in surface-enhanced Raman scattering of organic molecules

The formation of dense arrays of nanospikes occurs under laser ablation of bulk targets (Ag, Au, Ta, Ti) immersed in liquids such as water or ethanol. The average height of spikes is 50 nm and their density on the target amounts to 10¹⁰ cm⁻². The effect is observed with sufficiently short laser pulses. In particular, either a 350 ps or a 90 ps Nd:YAG lasers are used in their fundamental harmonics. The nanospikes are characterized by UV-Visible reflection spectrometry and atomic force microscopy. The oscillations of electrons within nanospikes result in a permanent coloration of the surface and a modification of the optical reflection spectra of the metal. Scanning the laser beam along the metal surface allows its nanostructuring over extended areas (∼1 cm²). The nanostructured Ag surface shows enhanced Raman scattering of acridine molecules at a concentration of 10⁻⁵ M/l, whereas the initial Ag targets do not show any signal within the accuracy of measurements.     

KrF laser ablation of a polyethersulfone film: Effect of pulse duration on structure formation

Polyethersulfone (PES) films were processed with KrF laser irradiation of different pulse durations (τ). Scanning electron microscopy (SEM) and Raman spectroscopy were employed for the examination of the morphology and chemical composition of the irradiated surfaces, respectively. During ablation with 500 fs and 5 ps pulses, localized deformations (beads), micro-ripple and conical structures were observed on the surface depending on the irradiation fluence (F) and the number of pulses (N). In addition, the number density of the structures is affected by the irradiation parameters (τ, F, N). Furthermore, at longer pulse durations (τ = 30 ns), conical structures appear at lower laser fluence values, which are converted into columnar structures upon irradiation at higher fluences. The Raman spectra collected from the top of the structures following irradiation at different pulse durations revealed graphitization of the ns laser treated areas, in contrast to those processed with ultra-short laser pulses.     

Synthesis of nanosized particles during laser ablation of gold in water

In this paper we report the formation of gold nanoparticles during laser ablation of gold target in water in the absence of any additives. The experiments were carried out by using the radiation of the pulsed Nd:YAG laser, operating at the second (532 nm, 10 ns, 10 Hz), or the fourth harmonic (266 nm) wavelengths. The properties of the nanoparticles were found to be susceptible to the additional 532 and 266 nm laser irradiation. It has been established that both the mean size of the nanoparticles and their stability could be varied by proper selection of the parameters of laser ablation and postirradiation such as laser fluence and wavelength combinations.     

Picosecond pulsed laser ablation and micromachining of 4H-SiC wafers

Ultra-short pulsed laser ablation and micromachining of n-type, 4H-SiC wafer was performed using a 1552 nm wavelength, 2 ps pulse, 5 μJ pulse energy erbium-doped fiber laser with an objective of rapid etching of diaphragms for pressure sensors. Ablation rate, studied as a function of energy fluence, reached a maximum of 20 nm per pulse at 10 mJ/cm², which is much higher than that achievable by the femtosecond laser for the equivalent energy fluence. Ablation threshold was determined as 2 mJ/cm². Scanning electron microscope images supported the Coulomb explosion (CE) mechanism by revealing very fine particulates, smooth surfaces and absence of thermal effects including melt layer formation. It is hypothesized that defect-activated absorption and multiphoton absorption mechanisms gave rise to a charge density in the surface layers required for CE and enabled material expulsion in the form of nanoparticles. Trenches and holes micromachined by the picosecond laser exhibited clean and smooth edges and non-thermal ablation mode for pulse repetition rates less than 250 kHz. However carbonaceous material and recast layer were noted in the machined region when the pulse repetition rate was increased 500 kHz that could be attributed to the interaction between air plasma and micro/nanoparticles. A comparison with femtosecond pulsed lasers shows the promise that picosecond lasers are more efficient and cost effective tools for creating sensor diaphragms and via holes in 4H-SiC.