Investigations on conductivity anomalies in Li2O·4MnO1+x·4B2O3 glasses

Glassy material Li₂O·4MnO_1+x·4B₂O₃ (0<x<0.5) has been prepared by quenching the melt in air, and its electrical conduction behavior has been studied. Two conductivity anomalies are observed around the glass transition temperature. One appears in the dependence of the isothermal conductivity vs. the annealing time. This anomaly is attributed to the oxidation of Mn²⁺ by oxygen ions penetrating into the glass matrix, leading to the increase of the charge carrier density. The other anomaly is observed in the dependence of the conductivity vs. the temperature for different times of annealing. The abnormal increase and decrease of the conductivity vs. annealing time might result from a complicated structural variation in the glass. Below 200°C, the conductivity obeys an Arrhenius relation. Above 350°C, the formation of crystalline MnBO₃ causes a conductivity decrease by one order of magnitude. The conductivity is enhanced by the redistribution of free volume between these two temperatures.     

Ionic and electronic conductivity in lead–zirconate–titanate (PZT)

Accurate impedance measurements on differently sized samples of lead–zirconate–titanate (PbZr_0.53Ti_0.47O₃, PZT) have been analyzed with a CNLS procedure, resulting in the separation of the ionic and electronic conductivities over a temperature range from 150 to 630 °C. At 603 °C the electronic conductivity shows approximately a (P_O2)^1/4 dependence, while the ionic conductivity remains constant. Below the Curie transition temperature the oxygen non-stoichiometry becomes frozen-in and the conductivities are strongly dependent on the sample history with respect to temperature sequence and ambient P_O2. A tentative interpretation assumes defect association, i.e. formation of neutral [V_Pb–V_O^··]^× complexes, and electron-hole transfer between lead sites and lead vacancies to control the oxygen ion conductivity in the tetragonal phase.

Annealing PZT-based devices at about 600 °C under low oxygen pressure (1 Pa oxygen) effectively decreases the low temperature electronic conductivity by a factor of 100 and the ionic conductivity by a factor of 10–15 with respect to normal air processing.     

Raman study of the phase separation in ZrO2-12 mol% CeO2 ceramic

We present Raman spectra of the ZrO₂-12 mol% CeO₂ ceramic heat- treated at 1000°C, 1200 °C and 1420 °C in the flowing mixture gas of H₂+Ar. Raman spectra reveal the tetragonal to monoclinic phase transition and three Raman bands are observed at 279 cm^-1, 410 cm^-1 and 456 cm^-1 at temperatures above 1200 °C; it turned out that these Raman bands are assigned to neither of the monoclinic phase nor the tetragonal phase. It is suggested that the starting ceramic undergoes phase separation in the heat-treatments in the mixture gas of H₂+Ar; the phase separation probably takes place as a result of the valence change of Ce during the heat-treatments, which leads to destabilization of the original tetragonal phase.     

Synthesis and characterization of the Aurivillius phases Bi2 − xPbxSr1 − xNdxNb2O9

The n = 2 Aurivillius phase Bi_{2 − x}Pb_xSr_{1 − x}Nd₂O₉ was successfully synthesized as a ceramic material over the whole range of simultaneous, charge compensated substitution x = 0–1.0. Structural investigations were performed by Rietveld refinement applying different space groups Fmmm and A2₁am, and additionally by X-ray absorption spectroscopy (EXAFS) on the Nd L_III-edge, confirming the accommodation of Nd on the atomic sites of Sr, which implies the substitution of Bi³⁺ by the isoelectronic Pb²⁺. The ferroelectric transition temperature T_c = 270 °C of the substituted powders with x = 0.4 and 1.0 is distinctly reduced compared to the unsubstituted sample with T_c = 450 °C. In temperature resolved powder X-ray diffraction patterns no structural phase transition could be detected.     

Poly(ethylene oxide-co-epichlorohydrin)/NaI: a promising polymer electrolyte for photoelectrochemical cells

We have investigated the thermal and ionic conductivity properties of the elastomer poly(ethylene oxide-co-epichlorohydrin) filled with NaI and I₂. The reason for using this composition is its potential application as electrolyte in photoelectrochemical cells. This copolymer was characterized as a function of NaI concentration, temperature and relative humidity. According to the data obtained, the Na⁺ ion interacts with the ethylene oxide repeating units by means of Lewis type acid–base interactions. The empirical Vogel–Tamman–Fulcher equation was used to model the conductivity and temperature relationships, indicating that the conduction occurs in the amorphous phase of the copolymer. The sample with 9.0% (w/w) of NaI presents a conductivity of 1.5×10⁻⁵ S cm⁻¹ in a dry atmosphere (30°C, [H₂O]<1 ppm) and 2.0×10⁻⁴ S cm⁻¹ at 86% relative humidity (22°C).     

The study of hydronium NASICON conductivity with deuterium

The ionic conductivity of the bulk phase of bonded hydronium NASICON (Hyceram^TM) was measured at equilibrium with an H₂O/N₂ and then a D₂O/N₂ atmosphere, each at 100% relative humidity and 75% relative humidity over the temperature range 25°C to 50°C. At 100% relative humidity and 25°C, the protonic system had a bulk conductivity of 5.0×10⁻⁴ S/cm and an activation energy of 17.3kJ/mole; the same sample, when deuterated, had a bulk conductivity of 2.2×10⁻⁴ S/cm and an activation energy of 19.3kJ/mole. At 75% relative humidity and 25°C, the conductivity of the protonated system decreased to 1.4×10⁻⁴S/cm with an activation energy of 24.1 kJ/mole. The deuterated sample at 75% relative humidity had a bulk conductivity of 5.4×10⁻⁵ S/cm with an activation energy of 26.0 kJ/mole. The isotope effect suggested a proton hopping (Grotthus) mechanism as the means by which the protons pass through the lattice.     

Material design of new lithium ionic conductor, thio-LISICON, in the Li2S–P2S5 system

A new lithium ionic conductor of the thio-LISICON (LIthium SuperIonic CONductor) family was found in the binary Li₂S–P₂S₅ system; the new solid solution with the composition range 0.0≤x≤0.27 in Li_3+5xP_1−xS₄ was synthesized at 700 °C and characterized by X-ray diffraction measurements. Its electrical and electrochemical properties were studied by ac impedance and cyclic voltammetry measurements, respectively. The solid solution member at x=0.065 in Li_3+5xP_1−xS₄ showed the highest conductivity value of 1.5×10⁻⁴ S cm⁻¹ at 27 °C with negligible electronic conductivity and the activation energy of 22 kJ mol⁻¹ which is characteristic of high ionic conduction state. The extra lithium ions in Li₃PS₄ created by partial substitution of P⁵⁺ for Li⁺ led to the large increase in ionic conductivity. In the solid solution range examined, the minimum conductivity was obtained for the compositions, Li₃PS₄ (x=0.0 in Li_3+5xP_1−xS₄) and Li₄P_0.8S₄ (x=0.2 in Li_3+5xP_1−xS₄); this conductivity behavior is similar to other thio-LISICON family with the general formula, Li_xM_1−yM_y′S₄ (M=Si, Ge, and M′=P, Al, Zn, Ga, Sb). Conduction mechanism and the material design concepts are discussed based on the conduction behavior and the structure considerations.     

Structural-phase transition and electrical conductivity in tin-modified zirconium titanate

The structural phase transition in tin-modified zirconium titanate was investigated using high-temperature X-ray, DTA, DSC and electrical conductivity. In a dilute solid solution of Sn (x 0.2) in Zr_1−xSn_xTiO₄, we ascribed to the successive phase transition from normal to incommensurate the break of electrical conductivity, thermal anomalies, and specific heat anomalies occurring at temperatures of 1121 °C, 1124 °C and 1125 °C on the heating run, and at temperatures of 1121 °C, 1116 °C and 1117 °C on the cooling run, respectively. Furthermore, the super-lattice reflection intensity was inversely proportional to the Sn content, cooling rate and electrical activation energy. With a composition of Zr_0.8Sn_0.2TiO₄, the phase transition from normal to incommensurate was completely inhibited.     

Electrical properties of calcia-doped ceria with oxygen ion conduction

The electrical conductivity of sintered specimens of (CeO₂)_1−x(CaO)_x was investigated by employing a standard four-probe dc technique as a function of temperature between 400°C and 900°C, composition from 0.10x0.80, and oxygen partial pressure from 10⁻¹⁸ to 1 atm. The temperature and composition dependence of the emf have been carried out with a concentration cell. X-ray diffraction studies indicated that a cubic fluorite crystal remained in all specimens studied, although the solubility limit of CaO in CeO₂ was assumed to lie close to 23 mol% from the change of the lattice constant. The magnitude of the conductivity decreased slightly with increase of the dopant concentrations up to x=0.50. The conductivity of these specimens was about 100 times larger than that of calcia-stabilized zirconia at 600°C with a smaller activation energies of 0.83–0.89 eV. With further increasing dopant concentrations, the magnitude of the conductivity was found to decrease remarkably. With an increase in the dopant concentration, the domain of primarily ionic conduction extended to a lower partial pressure. The conductivity of (CeO₂)_0.50(CaO)_0.50 was found to be primarily ionic down to 10⁻¹² atm even at 900°C. These results indicate that CaO-doped CeO₂ may be more an attractive candidate for fuel cells and other applications.     

High temperature transport processes in lithium niobate

The electrical conductivity of single crystal lithium niobate (LiNbO₃) was determined as a function of temperature for various oxygen partial pressures. The electrical conductivity is proportional to P_o2^−1/4 which can be explained by a defect equilibrium involving singly ionized oxygen vacancies and electrons.

Measurements of electrical transport numbers at 1000°K show the electrical conductivity of LiNbO₃ to be ionic at one atmosphere of oxygen and electronic at low oxygen partial pressures.

Thermoelectric measurements indicate that LiNbO₃ at low oxygen partial pressures is n-type and that the concentration of electrons at 1000°K and in an atmosphere of 50% C0/50% CO₂a is 4 × 10¹⁷cm³ with a mobility of 1.7 cm²V sec.

The diffusion of oxygen in LiNbO₃ was determined as a function of temperature at an oxygen partial pressure of 70 Torr. by measuring O¹⁸/O¹⁶ isotope exchange with the gas phase as a function of time. The diffusion data may be represented by D = 3.03 × 10⁻⁶ exp (−29.4 kcal mole⁻¹/RT)cm²sec. Consideration of the Nernst-Einstein relation for oxygen and the variation in conductivity with Li₂O activity indicate that the ionic conduction is caused by transport of lithium ions.     

Sr-doped LaInO3 and its possible application in a single layer SOFC

The effects of dopants on the electrical conductivity of the perovskite-type oxide LaInO₃ have been investigated. Replacement of La by Sr is the most effective way to enhance the conductivity of LaInO₃, whereas Ca substitution for In is rather difficult due to the large difference in the ion radii. The optimum composition is La_0.9Sr_0.1InO_3−δ whose maximum conductivity is 7.6×10⁻³ S cm⁻¹ at 900°C. The electrical conductivity of La_0.9Sr_0.1InO_3−δ has been measured over a wide range of oxygen partial pressure from pO₂=1 to 10⁻²⁵ atm. P-type and n-type behavior at high and low oxygen partial pressure have been observed, respectively, while at intermediate oxygen partial pressures, the electrical conductivity changes only slightly with the oxygen partial pressure. The concept of a single layer solid oxide fuel cell based on a La_0.9Sr_0.1InO_3−δ ceramic pellet has been tested. A maximum power density of 3 mW cm⁻² at 800°C was achieved when dilute H₂ and air were used as fuel and oxidizing agent, respectively.     

Low temperature fabrication of vanadium oxide films for uncooled bolometric detectors

Vanadium oxide films with temperature coefficient of resistant of −2.6% K⁻¹ have been fabricated on Si₃N₄-film-coated Si substrates by ion beam sputtering in a controlled Ar/O₂ atmosphere, at a relatively low growth temperature of 200 °C. The as-deposited films show no semiconductor-to-metal phase transitions even heated up to 150 °C. X-ray diffractometry shows that the main compound of the VO_x film is a metastable phase of vanadium dioxide (VO₂(B)) and the VO₂(B) film can be transformed into VO₂ film by post-growth annealing at 450 °C in flowing Ar atmosphere.     

Germanium and iron co-substituted SrCoO2.5+δ as oxygen permeable membrane

Germanium and iron co-doped SrCoO_2.5+δ was investigated in terms of phase stability, oxygen permeability and electrical conductivity. The favorable high-temperature cubic structure of SrCoO_2.5+δ was stabilized to lower temperatures by co-doping Ge (10 mol%) and Fe (10 mol%) that substituted for Co, which however could not be achieved by doping Ge (20 mol%) alone. In contrast to SrCo_0.8Ge_0.2O_2.5+δ sample which showed a sharp decrease in oxygen permeability at temperature of 875 °C upon cooling, SrGe_0.1Co_0.8Fe_0.1O_3−δ sample remained well-permeable to oxygen at lower temperatures down to at least 820 °C; an abrupt change in electrical conductivity in SrCo_0.8Ge_0.2O_2.5+δ also occurred accompanying the phase transition. The oxygen permeation flux for SrGe_0.1Co_0.8Fe_0.1O_3−δ increased significantly with the decrease of the membrane thickness, indicating the transport of oxygen ions in the bulk of the membrane as the rate-limiting step.     

Polymer electrolytes based on ethylene oxide–epichlorohydrin copolymers

In this work we studied the ionic conductivity for three copolymers of the title co-monomers as a function of LiClO₄ content, temperature and ambient relative humidity. We also investigated the interactions between the salt and the co-monomer blocks in the copolymers and its effect on the morphology and thermal properties of the copolymer/salt complexes. Our data indicate that the Li⁺ ion predominantly interacts with the ethylene oxide repeating units of the copolymers. The copolymer with the highest ionic conductivity was obtained with an ethylene oxide/epichlorohydrin ratio of 84/16 containing 5.5% (w/w) of LiClO₄. It showed a conductivity of 4.1×10⁻⁵ S cm⁻¹ (30°C, humidity< 1 ppm) and 2.6×10⁻⁴ S cm⁻¹ at 84% relative humidity (24°C). The potential stability window of the copolymer/salt complex is 4.0 V, as measured by cyclic voltammetry. For comparison, we also prepared a blend of the corresponding homopolymers containing LiClO₄; it showed higher crystallinity and lower ionic conductivity.     

Effect of branching in base polymer on ionic conductivity in hyperbranched polymer electrolytes

Novel hyperbranched polymer, poly[bis(diethylene glycol)benzoate] capped with a 3,5-bis[(3′,6′,9′-trioxodecyl)oxy]benzoyl group (poly-Bz1a), was prepared, and its polymer electrolyte with LiN(CF₃SO₂)₂, poly-Bz1a/LiN(CF₃SO₂)₂ electrolyte, was all evaluated in thermal properties, ionic conductivity, and electrochemical stability window. The poly-Bz1a/LiN(CF₃SO₂)₂ electrolyte exhibited higher ionic conductivity compared with a polymer electrolyte based on poly[bis(diethylene glycol)benzoate] capped with an acetyl group (poly-Ac1a), and the ionic conductivity of poly-Bz1a/LiN(CF₃SO₂)₂ electrolyte was to be 7×10⁻⁴ S cm⁻¹ at 80 °C and 1×10⁻⁶ S cm⁻¹ at 30 °C, respectively. The existence of a 3,5-bis[(3′,6′,9′-trioxodecyl)oxy]benzoyl group as a branching unit present at ends in the base polymer improved significantly ionic conductivity of the hyperbranched polymer electrolytes. The polymer electrolyte exhibited the electrochemical stability window of 4.2 V at 70 °C and was stable until 300 °C.     

Silver ionic conductivity enhancement by network former mixed in oxide-based glasses

Glasses in the binary system xAg₂P₂O₆ − (1 − x)Ag₂Te₂O₅ have been prepared for 0 x 1. For each composition only one glass transition temperature is observed in the temperature range of 180–220 °C. All glasses appear homogeneous considering their optical and electrical properties. Nevertheless, in SEM observations, some glass compositions appear to be heterogeneous after decoration following short nitric acid etching. For each composition, conductivity data obtained in the temperature range of 25–200 °C using impedance techniques obey an Arrhenius relationship with a composition independent pre-exponential term. Variation of the conductivity activation energy with x induces correlative variations of isothermal conductivity curves leading to an increase of the ionic conductivity of about one order of magnitude compared with linearity at 25 °C. This behaviour is discussed with respect to the thermodynamic properties of the glassy solutions.     

In situ surface analytical investigation of the thermal oxidation of Ti–Al intermetallics up to 1000 °C

The low pressure high temperature oxidation behavior of Ti–Al intermetallics are of interest to power technology aiming to synthesize this material by sintering of powders. This paper presents in situ surface analytical studies of the composition of a two-phase TiAl/Ti₃Al bulk microcrystalline system after oxidizing the same (sputtered) reference surface for 30 min at various oxygen partial pressures and temperatures varying between room temperature (RT) and 1000 °C. The results show that oxidation already begins at very low (<5×10⁻¹⁰ mbar) oxygen pressure, producing Al₂O₃ and the lower oxidation states of Ti. As the oxygen pressure and oxidation temperature increases, TiO₂ becomes dominant up to 900 °C. No phase transition of Al₂O₃ has been observed in this range. No sign of a blocking behavior of the oxide layer is seen. At 1000 °C a new oxide phase, Al₂TiO₅ appears, changing the composition and behavior of the surface drastically. The observed results can be explained by qualitative thermodynamic arguments. The thickness and composition of the oxide overlayer is, however, primarily determined by the oxygen supply.     

Origin of cathodic degradation and new phase formation at the La0.9Sr0.1MnO3/YSZ interface

New phase formation at the La_0.9Sr_0.1MnO₃/YSZ interface and its effects on the cathodic performances were studied at 900 °C in air. The resistance caused by the interfacial product layer kept increasing with time to reach up to 40% of the total resistance after 500 h. The interfacial product was identified as La₂Zr₂O₇ by XRD measurement. The electrical conductivity of La₂Zr₂O₇ (2.4 × 10⁻⁵ S cm⁻¹ at 1000 °C), measured by AC impedance and current interruption methods, was 4 to 7 orders of magnitude smaller than those of La_0.9Sr_0.1MnO₃ electrode or YSZ electrolyte. Either the electronic conductivity or the electrochemical O₂ reduction activity of La₂Zr₂O₇ was negligible. Combining these results, a conclusion was made that the cathodic degradation comes mainly from the growth of interfacial product layer and its contribution to the cell resistance increment is ohmic in nature.     

Surface morphology and electrical properties of Bi---Sr---Ca---Cu---O thin films deposited by reactive sputtering from multiple targets

Smooth, superconducting films of Bi₂Sr₂CaCu₂O_8+° have been prepared by reactive sputtering from elemental targets in the presence of ozone. The influence of substrate temperature, deposition rate, and ozone pressure on the resulting films are discussed. Films deposited on SrTiO₃ substrates are c-axis oriented and featureless for substrate temperatures below 710°C. Above this temperature, small inclusions of CuO appear. Films on MgO exhibit mixed a-axis and c-axis orientation below about 710°C, and inclusions of CuO above this temperature. The temperature at which this transition occurs increases with increasing deposition rate. T_c increases and then decreases sharply with decreasing oxygen content. The oxygen partial pressure corresponding to the maximum T_c of 77 K is well above the thermodynamic stability limit for Bi₂Sr₂CaCu₂O_8+°, suggesting that an optimum carrier concentration has been achieved for these films.