Sr2Bi4Ti5O18的压致结构相变

 使用4∶1的甲醇-乙醇混合液作传压介质，利用金刚石对顶砧装置（DAC），研究了层状铁电体Sr₂Bi₄Ti₅O₁₈的在位高压拉曼光谱和压致结构相变（0～27 GPa）。发现在8.31 GPa，Sr₂Bi₄Ti₅O₁₈经历了一次结构相交。在23.13 GPa以上，Sr₂Bi₄Ti₅O₁₈似乎出现了压致非晶相交的先兆。并使用内模方法对Sr₂Bi₄Ti₅O₁₈的内模进行了指认。     

复合层状Bi7Ti4NbO21铁电陶瓷的结构与介电和压电性能研究

制备了Bi₇Ti₄NbO_{21，Bi4Ti3O12及Nb掺杂Bi4Ti3O12(Nb-Bi4Ti3O12)层状结构铁电陶瓷材料.结合Nb-Bi 4Ti3O12的介电温谱和 退极化实验结果，研究了Bi7Ti4NbO21的晶体结构 对其介电、压电性能的影响 .高分辨透射电镜结果表明，在Bi7Ti4NbO21中， 沿着c轴方向，(Bi2Ti3O10)^2-和(BiTiNbO7)^2-两个类钙钛矿层分别 与(Bi2O2)²⁺层叠加堆积而成.这种晶体结构决定了Bi7Ti4NbO21的 介电温谱在668℃和845℃出现介 电双峰.结合极化样品的退化实验分析，说明材料在这两个温度附近发生了铁电—铁电相变 、铁电—顺电相变，分别是(Bi2Ti3O10)^{2-< /sup>和(BiTiNbO7)2-层状 结构发生微观结构相变的结果.在退极化过程中，由于受热时钙钛矿层内空位引起的缺陷偶 极子的定向排列受到破坏，引起材料部分退极化，表现为300℃热处理后Bi7Ti 4NbO 21的压电活性降低了10%，显示了室温下材料的压电性能来源于自发极化的固有电 偶极子和缺陷偶极子的共同贡献.}}     

纤维状TiO2/Bi2O3光催化剂的制备及其光催化性能

以C₁₆H₃₆O₄Ti和Bi(NO₃)·5H₂O为原料,以棉花纤维为生物模板,合成了系列纤维状TiO₂/Bi₂O₃光催化剂．采用XRD、SEM、UV-Vis等测试技术对样品的相结构、形貌和吸光性能等进行了表征分析．结果表明,样品中的Bi₂O₃为单斜相和四方相共存的混晶,纤维长度达到毫米级,     

Nd掺杂对Bi4Ti3O12铁电薄膜的微结构和铁电性能的影响

利用溶胶-凝胶法在Pt/Ti/SiO₂/Si(100)衬底上制备了Nd掺杂Bi₄Ti₃O₁₂(Bi_4-xNd_xTi₃O₁₂, x=0.00,0.30,0.45,0.75,0.85,1.00,1.50)铁电薄膜样品.研究了Nd掺杂对Bi₄Ti₃O₁₂薄膜的微结构和铁电性能的影响.研究结果表明:Nd掺杂未改变Bi₄Ti₃O₁₂薄膜的基本晶体结构.在掺杂量x<0.45时,Nd³⁺只取代类钙钛矿层中的A位Bi³⁺.当x=0.45时,样品剩余极化强度达最大值,在270kV·cm^-1的电场下为32.7μC·cm^-2.掺杂量进一步增加时,结构无序度开始明显增大,Nd³⁺开始进入(Bi₂O₂)²⁺层,削弱其绝缘层和空间电荷库的作用,导致材料剩余极化逐渐下降.当掺杂量x达到1.50时,掺杂离子最终破坏(Bi₂O₂)²⁺层的结构,材料发生铁电-顺电相变.     

焙烧温度对SiO2负载的Co3O4纳米粒子表面氧缺陷浓度和CO氧化催化性能的影响

以传统的浸渍法,在不同焙烧温度下制备了用于CO氧化反应的Co₃O₄/SiO₂催化剂．通过激光拉曼光谱(Raman)、X射线光电子能谱(XPS)、X射线衍射(XRD)、程序升温还原(TPR)和X射线吸收精细结构谱(XAFS)表征了该系列催化剂的结构．在所有的催化剂中,XRD和Raman光谱都只检测到了Co₃O₄晶相的存在．与Co₃O₄体相相比,XPS结果表明在200 oC焙烧的(Co₃O₄(200)/SiO₂)催化剂中Co₃O₄表面上存在着过量的Co²⁺．与XPS的结果一致,TPR结果表明Co₃O₄(200)/SiO₂催化剂中Co₃O₄表面上存在氧缺陷, 并且XAFS结果也表明Co₃O₄(200)/SiO₂催化剂中Co₃O₄具有更多的Co²⁺．提高焙烧温度使得过量的Co²⁺进一步氧化为Co³⁺,同时降低了表面氧缺陷浓度,从而得到计量比的Co₃O₄4/SiO₂催化剂．在所有的负载催化剂中Co₃O₄(200)/SiO₂催化剂表现出了最好的CO氧化催化性能,表明过量Co²⁺和表面氧缺陷的存在能够促进Co₃O₄催化CO氧化反应的活性.     

CO和O2分子与TiO2(110)表面负载Pt单原子的相互作用

Pt单原子在低温CO氧化反应中具有很高的催化活性. 利用扫描隧道显微术与密度泛函理论,研究了Pt单原子在还原性TiO₂(110)表面的吸附行为及其与CO和O₂分子的相互作用. 研究发现在80 K低温下,TiO₂表面的氧空位缺陷是Pt单原子的最优吸附位. 将CO和O₂分子分别通入Pt单原子吸附后的TiO₂表面,研究相应的吸附构型. 实验表明在低覆盖度下,单个Pt原子会俘获一个CO分子,CO分子同时与表面次近邻的五配位Ti原子(Ti_5c)成键,进而形成非对称的Pt-CO 复合物构型. 将样品从80 K升温到100 K后,TiO₂表面的CO分子会迁移到Pt-CO处形成Pt-(CO)₂的复合结构. 对于O₂分子,单个Pt原子同样会吸附一个O₂分子,O₂分子也会与最近邻或次近邻的Ti_5c原子成键形成两种Pt-O₂构型. 这些结果在单分子尺度上揭示了CO和O₂与Pt单原子的相互作用,呈现了CO与O₂反应中的初始状态.     

锂离子正极材料正交相γ-LiV2O5的制备及性能

分别采用LiOH·H₂O, NH₄VO₃, HNO₃, C₂H₅OH作为原料在没有PVP和有PVP存在下合成了棒状和棒束状两种相貌的γ-LiV₂O₅. 棒状γ-LiV₂O₅材料中棒的直径为500～800 nm,而棒束状的γ-LiV₂O₅材料则是直径为100～600 nm的棒组成的,形貌比较均匀. 同时研究了此体系中γ-LiV₂O₅的合成机制. 将合成的材料进行电化学测试,棒束状的γ-LiV₂O₅ 的电化学性能更好,在电流密度为30 mA/g时的初始放电比容量为269.3 mAh/g,循环20次之后容量仍保持在228 mAh/g.     

氧含量对CaCu3Ti4O12巨介电常数和介电过程的影响

本文研究了在真空、空气和氧气中烧结制备的三种 CaCu₃Ti₄O₁₂陶瓷材料的介电特性. 交流阻抗测量结果表明在10—300 K温度范围, 三种样品的介电温谱中均出现三个平台, 其电阻实部和电容虚部在相应温度出现损耗峰, 真空条件烧结的样品具有较高的介电平台和较明显的电阻实部与电容虚部峰值, 表明氧含量和氧空位对CaCu₃Ti₄O₁₂的介电性质具有重要影响, 介电温谱出现的三个平台分别源于晶粒、晶界及氧空位陷阱.温谱分析表明晶粒的激活能与烧结气氛有较大关系,氧空位引起的电子短程跳跃及跳跃产生的极化子是晶粒电导和电容的主要起源.氧空位陷阱的激活能基本与烧结气氛无关,约为0.46 eV. 氧空位对载流子的陷阱作用是CaCu₃Ti₄O₁₂ 低频高介电常数的重要起源.     

Ba0.98Ce0.8Tm0.2O3-α的离子导电性及其燃料电池性能

用高温固相反应法制备了Ba_0.98Ce_0.8Tm_0.2O_3-α钙钛矿型氧化物固溶体,粉末X射线衍射表明该固溶体为单相. 用交流阻抗谱技术和气体浓差电池方法研究了样品在500～900 oC、不同气体气氛中的导电性,以及该样品为固体电解质的氢-空气燃料电池性能. 该电池能稳定地工作,在900 oC时,电池的最大功率密度为110.2 mW/cm²,高于以Ba_xCe_0.8RE_0.2O₃^- (x≤1, RE=Y, Eu, Ho)为固体电解质的氢-空气燃料电池的功率密度     

生物油及生物质炭电催化制氢

报道了以生物质热裂解产物-生物油和生物质炭为原料,利用双固定床反应器和电催化水蒸气重整方法高效制氢过程研究．获得的最大绝对氢产率达到110.9 g H₂/1 kg干生物质,气相产物包括72%H₂、26%CO₂、1.9%CO和痕量的CH₄．研究了添加生物质炭对生物油制氢效果的影响,以及重整反应温度、通入催化床的电流等反应条件对生物油和生物质炭制氢效果的影响．结果表明,生物质炭的添加使绝对氢产率增加了大约20%～45%,提     

Thermomechanical and conductivity studies of doped niobium titanates as possible current collector material in the SOFC anode

In the reducing atmosphere of the SOFC anode at operating temperatures of 800 °C and above Nb₂TiO₇ is reduced to Nb_1.33Ti_0.67O₄. This material displays very high electronic conductivity of >100 Scm⁻¹, suitable for use in such applications as a current collector. It has a low thermal expansion coefficient of 3 × 10⁻⁶ K⁻¹, however, which may cause problems due to mismatch with other SOFC components, e.g. YSZ. Doping with Fe₂O₃ successfully increased the thermal expansion to a maximum of 6 × 10⁻⁶ K⁻¹. A conductivity of 140 Scm⁻¹ at 900 °C in dry 5% H₂/Ar, with an activation energy of 0.18 eV, was achieved for the Nb_1.344Ti_0.642Fe_0.014O₄, making it suitable for the use as a current collector. Conductivity runs in wet 5%H₂/Ar showed lower conductivities of 15–18 Scm⁻¹ and lower activation energies of 0.08 − 0.09 eV. Single cell tests of Nb_1.33Ti_0.67O₄ showed power outputs of 5.5 − 7.2 mW·cm⁻² at 850 °C, lower than for Ni with 150 − 200 mW·cm⁻² at 850 °C, however, this material displayed much better stability at high temperatures than Ni. Paper presented at the 9th EuroConference on Ionics, Ixia, Rhodes, Greece, Sept. 15 – 21, 2002.     

Electronic structure and optical properties of Nb-doped Sr2TiO4 by density function theory calculation

This paper investigates the effect of Nb doping on the electronic structure and optical properties of Sr2TiO4 by the first-principles calculation of plane wave ultra-soft pseudo-potential based on density functional theory(DFT).The calculated results reveal that due to the electron doping,the Fermi level shifts into conduction bands(CBs) for Sr2 Nb x Ti1 x O4 with x=0.125 and the system shows n-type degenerate semiconductor features.Sr2TiO4 exhibits optical anisotropy in its main crystal axes,and the c-axis shows the most suitable crystal growth direction for obtaining a wide transparent region.The optical transmittance is higher than 90% in the visible range for Sr2 Nb 0.125Ti0.875O4.     

Structure and physical properties of Li4Ti5O12 synthesized at deoxidization atmosphere

Powders of spinel Li₄Ti₅O₁₂ (LTO) were successfully synthesized at reducing conditions by solid-state method. The structure and physical properties of Li₄Ti₅O₁₂ were examined by X-ray diffraction (XRD), Raman spectroscopy, scanning electronic microscopy (SEM), and differential capacitance, respectively. XRD shows that both samples are single-phase spinel compounds. LTO synthesized in Ar/H₂(8% mol) has a larger lattice parameter than that in Ar. SEM indicates that all of the prepared powders have the uniform, nearly cubic structure morphology with narrow size distribution in the range of 200–300 nm. Raman spectra indicate that the Raman bands corresponding to the Ti–O vibration has a blue shift from 674 to 680 cm⁻¹ due to the few H₂ in the synthesized condition, indicating that there is very few oxygen vacancies in the Li₄Ti₅O₁₂ synthesized under Ar/H₂ (8% mol). The dQ/dV vs. voltage plots reveals the redox potentials for the synthesized Li₄Ti₅O₁₂-negative electrode materials.     

Ferroelectric-relaxor behavior of (Na0.5K0.5)NbO3-based ceramics

We report that ferroelectric-relaxor behavior is induced by doping of SrO and TiO₂, or BaO and TiO₂ into classic ferroelectric (Na_0.5K_0.5)NbO₃. It is found that [(Na_0.5K_0.5)_0.9Sr_0.1](Nb_0.9Ti_0.1)O₃ ceramics exhibit a pronounced ferroelectric-relaxor behavior, comparable to that of [(Na_0.5K_0.5)_0.9Ba_0.1](Nb_0.9Ti_0.1)O₃ ceramics. Our results indicate that the relaxor behavior is closely related to the appearance of micropolar regions in these systems. The relaxor behavior should arise from the dynamic response of micropolar clusters. Raman spectra of [(Na_0.5K_0.5)_1−xSr_x](Nb_1−xTi_x)O₃ ceramics measured in the wavenumber range from 100 to 1200 cm⁻¹ confirm that the first order scattering is dominant in phonon bands should result from both short-range ordered region (micropolar regions) and disordered matrix. The frequency dependence of dielectric permittivity measurements show that the relaxor behavior of SrO and TiO₂, or BaO and TiO₂ doped (Na_0.5K_0.5)NbO₃ ceramics is not a Debye type in the radio frequency range.     

NbTi0.5Ni0.5O4 as anode compound material for SOFCs

NbTi_0.5Ni_0.5O₄ (NTNO) has been prepared using solid state synthesis and investigated as a potential anode material. The oxide form of NTNO has single phase rutile-type structure with tetragonal (P42/mnm) space group. The reduced form is a composite of nano-scaled particles of metallic Ni and Nb_1.33Ti_0.67O₄ phase. Reduced NTNO showed high electronic conductivity up to 280 S.cm^− 1 at 900 °C in reducing atmosphere, but suffers from low CTE equal to 3.78 10^− 6 K^− 1. Studies of NTNO as anode material were carried out in a three electrode - electrochemical half cell configuration under pure humidified H₂ at 900 °C using a 2 mm thick zirconia electrolyte and without any additional current collector material. The results show a reasonable series resistance (R_s) equal to 2.7 Ωcm² (about 50% higher than for metallic gold layers) indicating a good current collection performance for a 10 μm layer of material. The polarization resistance (R_p) was equal to 33 Ωcm² and is attributed to a poor density of three phase boundaries (TPB) and shortage of oxide ion conduction in the anode layer. The results show the potential of NTNO as an anode material, especially after optimization of the microstructure towards the increase of TPB length.     

Demonstration of medium temperature,one atmosphere reversible H2/O2 fuel and steam electrolysis cell operation using polycrystalline H3O+β/β″ -Al2O3

The development of a reversible fuel and steam electrolysis cell based on an H₃O⁺β/β″ -Al₂O₃ solid electrolyte is described. The unit has been operated between 100 and 300°C at one atmosphere steam pressure. The major limitations are discussed with reference to the solid electrolyte and the method of electrode preparation.     

Photocatalytic activity of Nb2O5/SrNb2O6 heterojunction on the degradation of methyl orange

The pure SrNb₂O₆ powders were prepared at 1400 °C by a conventional solid-state method and characterized by X-ray powder diffraction and UV-vis diffuse reflection spectrum. The powders of Nb₂O₅ and SrNb₂O₆ were ball-milled together and annealed to form the Nb₂O₅/SrNb₂O₆ composite. Photocatalytic activities of the composites were investigated on the degradation of methyl orange. The results show that the proportion of Nb₂O₅ to SrNb₂O₆ and the annealing temperature greatly influence the photocatalytic activities of the composites. The best photocatalytic activity occurs when the weight proportion of Nb₂O₅ to SrNb₂O₆ is 30% and the annealing temperature is 600 °C. The tremendously enhanced photocatalytic activity of the Nb₂O₅/SrNb₂O₆ composite compared to Nb₂O₅ or SrNb₂O₆ is ascribed to the heterojunction effect taking place at the interface between particles of Nb₂O₅ and SrNb₂O₆. The powders also show a higher photocatalytic activity than commercial anatase TiO₂.     

第二相Ba6Ti17O40形成动力学的研究

本文对添加过量TiO₂的BaTiO₃中所形成的第二相Ba₆Ti₁₇O₄₀的动力学进行了高温X射线衍射的实验研究,得到在不同温度下的富钛相Ba₆Ti₁₇O₄₀形成时的反应曲线,计算了反应速率常数K和反应激活能Q,并对第二相形成机制和过量钛的影响进行了讨论。 关键词：     

Single-calcination synthesis of pyrochlore-free Pb(Ni1/3Nb2/3)O3-PbTiO3 using a coating method

Pyrochlore-free 0.64Pb(Ni_1/3Nb_2/3)O₃-0.36PbTiO₃ (0.64PNN-0.36PT) powder has been successfully synthesized by only one calcination step using a coating method. The formation of pyrochlore phase is prevented by coating NiCO₃·2Ni(OH)₂·2H₂O on Nb₂O₅ particles. NiCO₃·2Ni(OH)₂·2H₂O-coated Nb₂O₅ powder is prepared by heterogeneous precipitation method. The coating structure is confirmed by transmission electron microscope (TEM) with energy dispersive spectroscope (EDS). Single calcination treatment of the coating powder mixed with appropriate amounts of Pb₃O₄ and TiO₂ powders at 900 °C for 2 h produces the pure-perovskite 0.64PNN-0.36PT powder. The elimination of the pyrochlore phase can be explained in terms of the separating of Pb₃O₄ and Nb₂O₅ by the NiCO₃·2Ni(OH)₂·2H₂O coating layer.     

Preparation, structure and ferromagnetic properties of the nanocrystalline Ti1-xMnxO2 thin films grown by radio frequency magnetron co-sputtering

This paper reported that the Mn-doped TiO2 films were prepared by radio frequency （RF） magnetron cosputtering. X-ray diffraction measurements indicate that the samples are easy to form the futile structure, and the sizes of the crystal grains grow big and big as the Mn concentration increases. X-ray photoemlssion spectroscopy measurements and high resolution transmission electron microscope photographs confirm that the manganese ions have been effectively doped into the TiO2 crystal when the Mn concentration is lower than 21%. The magnetic property measurements show that the Ti1-xMnxO2 （x = 0.21） films are ferromagnetic at room temperature, and the saturation magnetization, coercivity, and saturation field are 16.0 emu/cm^3, 167.5 × 80 A/m and 3740 × 80 A/m at room temperature, respectively. The room-temperature ferromagnetism of the films can be attributed to the new futile Ti1-xMnxO2 structure formed by the substitution of Mn^4＋ for Ti^4＋ into the TiO2 crystal .lattice, and could be explained by O vacancy （Vo）-enhanced ferromagnetism model.