通过掺杂V和F提高碳包覆的磷酸铁锂锂离子电池的电化学性能

在原位聚合合成方法的基础上,结合两步烧结过程制得LiFe_1-xV_x(PO₄)_(3-y)/₃F_y/C.V和F掺杂对碳包覆的磷酸铁锂材料的结构、形貌和电化学性能有影响.通过XRD、FTIR、SEM、充/放电测试和电化学阻抗谱对材料的结构、形貌和电化学性能进行了表征.结果表明,V和F的掺杂并没有破坏橄榄石结构中的LiFePO₄/C,但可以提高晶体结构的稳定,降低电荷的转移阻抗,提高锂离子扩散速度,改善了LiFePO₄/C材料的循环性能和高倍率性能.     

Pd修饰Cu电极的电化学CO2还原

利用微分电化学质谱和电化学原位衰减全反射红外光谱技术探究了Cu和CuPd催化剂上CO₂和CO的电化学还原行为. 红外光谱观察到了生成甲醇、甲烷与乙烯的CH_x中间物种. 在CuPd电极CO₂还原过程中,红外光谱的CO吸附峰起始电位比Cu正移大约300 mV,说明CuPd能够有效促进CO₂还原;CO饱和溶液中,Cu和CuPd电极CO起始吸附电位基本相同;两电极上CO谱带出现的电位与CO₃^2-的谱带降低的电位基本相同,说明CO的吸附需要CO₃^2-的脱附. 利用电化学在线质谱发现在CuPd电极上CO还原产生CH₄和CH₃OH的起始电位比Cu电极正移约200 mV. 推测催化活性的提升可能是由于Pd的引入改变了Cu的d能带,且Pd吸附更多的H,从而促进CO₂还原,使CO能够与H结合并被深度还原.     

Mn掺杂LiFePO4的第一性原理研究

采用基于密度泛函理论的第一性原理方法, 计算了不同Mn掺杂浓度LiFe_1-xMn_xPO₄ (x=0,0.25,0.50,0.75) 的电子结构. 同时采用流变相辅助高温固相碳热还原法制备了LiFe_1-xMn_xPO₄ (x= 0,0.25,0.50,0.75) 材料. 理论计算表明: LiFePO₄具有E_g = 0.725 eV的带隙宽度, 为半导体材料. 通过Fe位掺杂25%的Mn离子可最大程度地 减小材料带隙宽度、降低Fe---O键及Li---O键键能, 进而提高材料的电子电导率及锂离子扩散速率. 实验结果亦表明, 当Mn掺杂量x=0.25时, 材料具有最优的电化学性能, 其具有约为158 mAh· g^-1的放电比容量以及551 Wh· kg^-1的能量密度. 理论计算与实验结果非常符合.     

氧化还原可逆Nb2TiO7复合阴极电解池高温水蒸气电解研究

系统地研究Nb₂TiO₇与Nb_1.33Ti_0.67O₄材料相互转变的氧化还原循环可逆性能,同时研究Nb2TiO7和Nb_1.33Ti_0.67O₄样品随温度和氧分压变化的电导率,并与复合电极对称电池和电解池的电化学性能相关联. 在830 oC下,对Nb_1.33Ti_0.67O₄复合电极电解池进行水蒸气的电解研究测试. 电流电压曲线和电解池短期性能测试表明在低电压下主要为电极的还原和活化过程;而在高电压下主要为水蒸气的电解. 当3%H₂O/Ar/4%H_{2气体通入阴极时电解池水蒸气电解的法拉第效率为98.9%;而当通入气体转换为3%H2O/Ar时效率为89%.}     

Au(111)上过氧化氢在碱性介质中氧化反应的pH效应

本文经过系统地研究Au(111)上过氧化氢在pH值从10到13的不同碱性溶液体系中氧化反应(HPOOR),发现随着溶液pH的增大,HPOOR的活性增大,电流电势i-iE极化曲线的斜率减小. HO₂^-是碱性溶液中HPOOR的主要反应物种,在高pH溶液下有很快的动力学反应主要是由于电极表面的正电荷与体系中的阴离子HO₂^-和OH^-等有静电相互作用的原因. 因此在溶液反应物随pH增大的时候,热力学的驱动力也加快了HO₂^-的氧化过程.     

锂离子正极材料正交相γ-LiV2O5的制备及性能

分别采用LiOH·H₂O, NH₄VO₃, HNO₃, C₂H₅OH作为原料在没有PVP和有PVP存在下合成了棒状和棒束状两种相貌的γ-LiV₂O₅. 棒状γ-LiV₂O₅材料中棒的直径为500～800 nm,而棒束状的γ-LiV₂O₅材料则是直径为100～600 nm的棒组成的,形貌比较均匀. 同时研究了此体系中γ-LiV₂O₅的合成机制. 将合成的材料进行电化学测试,棒束状的γ-LiV₂O₅ 的电化学性能更好,在电流密度为30 mA/g时的初始放电比容量为269.3 mAh/g,循环20次之后容量仍保持在228 mAh/g.     

Mn3O4包覆对LiNi0.5Mn1.5O4正极材料界面电化学性能的提高

本文采用化学湿磨法,首次将金属氧化物Mn₃O₄包覆于LiNi_0.5Mn_1.5O₄颗粒表面,使得电极材料的电子电导率从1.53×10^-7 S/cm 提高到3.15×10^-5 S/cm. 电化学测试结果表明Mn₃O₄包覆大大提高LiNi_0.5Mn_1.5O₄正极材料的倍率性能和高温循环稳定性. 最佳包覆样品为2.6wt% Mn₃O₄包覆的LiNi_0.5Mn_1.5O₄,在10 C倍率下具有108 mAh/g的高放电容并且在55 °C下100次循环后仍有78%的容量保持率,远大于未包覆样品67%的容量保持率.     

原位聚合法制备凝胶型离子液体/PMMA聚合物电解质

采用原位聚合法制备了含有N-甲基、丙基哌啶双三氟甲磺酰亚胺离子液体的凝胶型聚合物电解质．利用SEM和XPS测试了电解质膜与LiFePO₄电极的界面状态,充放电循环后,在电解质膜与LiFePO₄之间有一层薄膜,这层薄膜中含有N和S元素．结果表明,随着充放电的不断进行,凝胶型电解质中未聚合的甲基丙烯酸甲酯与电极表面的锂离子之间发生电子转移,形成SEI膜,至少要三个循环后才能形成稳定的SEI膜．随着SEI膜的增厚,放电容量增加,阻碍了电子转移,使系统更加的稳定．在不同     

碳热还原法制备V2O3-C双层包覆磷酸铁锂及其电化学性能

通过V₂O₅的碳热还原反应制备了具有优异倍率性能和循环稳定性的V₂O₃-C双层包覆的磷酸铁锂正极材料. 粉末X射线衍射、元素分析、高分辨投射电镜和拉曼光谱研究表明V2O3相与碳层共包覆于磷酸铁锂颗粒表面. 在V₂O₅的碳热还原反应后,碳含量明显降低,但石墨化程度未发生明显改变. 电化学测试结果表明少量V₂O₃显著改善了磷酸铁锂正极材料的倍率性能和高温循环性能,包含1%氧化钒的复合正极材料在0.2 C放电容量为167 mAh/g,5 C时放电容量为129 mAh/g,并且循环稳定性优异;在55 oC和1 C时放电容量为151 mAh/g,循环100次后无明显容量衰减.     

三维海胆状Co3O4的微纳结构制备及锂电池性能

水热法制备的合成海胆状Co₃O₄前驱物在空气中退火得到三维海胆状Co₃O₄的微纳结构. 采用FESEM、TEM、HRTEM以及XRD对产物进行形貌和结构的表征. 结果表明,合成的海胆状结构Co₃O₄由许多粒径约为15 nm的颗粒串接形成. 锂电池测试性能表明,制备的海胆状Co₃O₄首次放电容量达到1.369 Ah/g,经过20次循环     

Effect of carbon coating on the electrochemical performance of LiFePO<Subscript>4</Subscript>/C as cathode materials for aqueous electrolyte lithium-ion battery

Organic electrolyte is widely used for lithium-ion rechargeable batteries but might cause flammable fumes or fire due to improper use such as overcharge or short circuit. That weakness encourages the development of tools and materials which are cheap and environmental friendly for rechargeable lithium-ion batteries with aqueous electrolyte. Lithium iron phosphate (LiFePO₄) with olivine structure is a potential candidate to be used as the cathode in aqueous electrolyte lithium-ion battery. However, LiFePO₄ has a low electronic conductivity compared to other cathodes. Conductive coating of LiFePO₄ was applied to improve the conductivity using sucrose as carbon source by heating to 600 °C for 3 h on an Argon atmosphere. The carbon-coated LiFePO₄ (LiFePO₄/C) was successfully prepared with three variations of the weight percentage of carbon. From the cyclic voltammetry, the addition of carbon coatings could improve the stability of cell battery in aqueous electrolyte. The result of galvanostatic charge/discharge shows that 9 % carbon exhibits the best result with the first specific discharge capacity of 13.3 mAh g^?1 and capacity fading by 2.2 % after 100 cycles. Although carbon coating enhances the conductivity of LiFePO₄, excessive addition of carbon could degrade the capacity of LiFePO₄.     

离子液体凝胶聚合物电解质PP13TFSI-LiTFSI-P(VdF-HFP)的电化学性能 (cited: 1)

采用溶液浇铸法将N-甲基-N-丙基哌啶二(三氟甲基磺)亚胺(PP13TFSI)、二(三氟甲基磺)亚胺锂与偏氟乙烯-六氟丙烯共聚物(P(VdF-HFP))混合制备离子液体凝胶聚合物电解质(ILGPEs). 通过扫描电子显微镜观察发现,这种离子液体凝胶聚合物电解质由于液体相的均匀分布而具有疏松的结构. 采用电化学阻抗、计时电流法、线性扫描伏安法测试了电解质的离子电导率、锂离子迁移数和电化学窗口. 室温下离子液体凝胶聚合物电解质的离子电导率和锂离子迁移数分别是0.79 mS/cm和0.71,电化学窗口为0～5.1 Vvs. Li⁺/Li. 电池性能测试表明,这种离子液体凝胶聚合物电解质在Li/LiFePO₄电池中是稳定的,放电容量在30、75和150mA/g倍率下分别为135、117和100 mAh/g,电池经100个循环后容量保持在100%而几乎没有衰减.     

Propylene oxide-assisted fast sol–gel synthesis of mesoporous and nano-structured LiFePO4/C cathode materials

LiFePO₄/C nanocomposites are synthesized by a propylene oxide-assisted fast sol–gel method using FeCl₃, LiNO₃, NH₄H₂PO₄, and sucrose as the starting materials. It was found that after adding propylene oxide into the solution containing the starting materials, a monolithic jelly-like FePO₄ gel containing lithium and carbon source is generated in a few minutes without controlling the pH value of the solution and a time-consuming heating process. Propylene oxide plays a key role in the fast generation of the precursor gel. The final products of LiFePO₄/C are obtained by sintering the dry precursor gel. The structures, micro-morphologies, and electrochemical properties of the LiFePO₄/C composites are investigated using X-ray diffraction, scanning electron microscopy, transmission electron microscopy, nitrogen adsorption–desorption analysis, electrochemical impedance spectrum, and charge–discharge cycling tests. The results indicate that the LiFePO₄/C composite prepared by sintering the precursor gel at 680 °C for 5 h is about 30 nm in size with a meso-porous structure (the main pore size distribution is around 3.4 nm). It delivers 166.7 and 105.8 mAh g^?1 at 0.2 and 30 C, respectively. The discharge specific capacity is 97.8 mAh g^?1 even at 40 C. The cycling performance of the prepared LiFePO₄/C composite is stable. The excellent electrochemical performance of the LiFePO₄/C composite is attributed to the nano-sized and mesoporous structure of LiFePO₄/C and the in-situ surface coating of the carbon. It was also found that propylene oxide is crucial for the generation of mesoporous and nano-structured LiFePO₄/C.     

Synthesis of spherical LiFePO4/C via Ni doping

Spherical LiFePO₄/C powders were synthesized by the conventional solid-state reaction method via Ni doping. Low-cost asphalt was used as both the reduction agent and the carbon source. An Ni-doped spherical LiFePO₄/C composite exhibited better electrochemical performances compared to an un-doped one. It presented an initial discharge capacity of 161 mAhg⁻¹ at 0.1 C rate (the theoretical capacity of LiFePO₄ with 5 wt% carbon is about 161 mAhg⁻¹). After 50 cycles at 0.5 C rate, its capacity remained 137 mAhg⁻¹ (100% of the initial capacity) compared to 115 mAhg⁻¹ (92% of the initial capacity) for an un-doped one. The electrochemical impedance spectroscopy analysis and cyclic voltammograms results revealed that Ni doping could decrease the resistance of LiFePO₄/C composite electrode drastically and improve its reversibility.     

CdSe–Au nanorod networks welded by gold domains: a promising structure for nano-optoelectronic components

LiFePO_4?x F _x /C nanorods were prepared by room-temperature solid-state reaction and microwave heating. The structure and morphology of the as-prepared materials were analyzed by X-ray diffractometry and transmission electron microscopy. The results shows that the LiFePO_4?x F _x /C were well crystallized and consisted of nanoparticles with an average diameter of ten to several tens of nanometers, many round grains constituted solid rod-like structure. The length of the rods can be up to several hundreds of nanometers, and their diameters are around 100?nm. The results of electrochemical testing show that the initial discharge capacity of LiFePO_3.85F_0.15/C is 124.7?mAh?g^?1, with a negligible fading after 50 cycles at a constant current density of 1 C at room temperature. The capacity retention rate is 99.5?%, which is higher than that of LiFePO₄/C prepared by the same method. The doping of F helps improve electrical conductivity and Li⁺ diffusion of LiFePO₄/C. This study may provide new insights and understanding on the effect of F-doping on the electrochemical performance of LiFePO₄/C.     

Enhanced electrochemical performance of LiFePO4/C prepared by sol–gel synthesis with dry ball-milling

LiFePO₄/C was prepared by a modified aqueous sol–gel route developed by incorporating an additional ball-milling step where the dry gel was milled with the additives of synthetic graphite and carbon black. The materials were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET), transmission electron microscopy (TEM), high resolution TEM (HRTEM) and elemental analysis. Results showed that the LiFePO₄/C synthesized by suitable ball-milling process had pure, fine and homogenous LiFePO₄ particles. Results of cyclic voltammetry and charge/discharge plateaus demonstrated that the LiFePO₄/C composite synthesized by milling for 2 h had much better electrochemical kinetics. High performances were achieved with its discharge capacities of 157 mA h g^?1 at 0.1?C and 133 mA h g^?1 at 1?C between 2.5 and 4.2 V (1?C?=?170 mA g^?1). And no obvious capacity fading was observed upon cycling. The simple and convenient synthesis route is promising for large-scale production of LiFePO₄/C.     

Electrochemical characterization of ionic liquid based gel polymer electrolyte for lithium battery application

High molecular weight polymer poly(vinylidenefluoride-co-hexafluoropropylene) (PVdF-HFP), ionic liquid 1-ethyl-3-methylimidazolium bis(fluorosulfonyl)imide (EMIMFSI), and salt lithium bis(trifluoromethanesulfonyl)imide (LiTFSI)-based free-standing and conducting ionic liquid-based gel polymer electrolytes (ILGPE) have been prepared by solution cast method. Thermal, electrical, and electrochemical properties of 80 wt% IL containing gel polymer electrolyte (GPE) are investigated by thermogravimetric (TGA), impedance spectroscopy, linear sweep voltammetry (LSV), and cyclic voltammetry (CV). The 80 wt% IL containing GPE shows good thermal stability (~?200 °C), ionic conductivity (6.42?×?10^?4 S cm^?1), lithium ion conductivity (1.40?×?10^?4 S cm^?1 at 30 °C), and wide electrochemical stability window (~?4.10 V versus Li/Li⁺ at 30 °C). Furthermore, the surface of LiFePO₄ cathode material was modified by graphene oxide, with smooth and uniform coating layer, as confirmed by scanning electron microscopy (SEM), and with element content, as confirmed by energy dispersive X-ray (EDX) spectrum. The graphene oxide-coated LiFePO₄ cathode shows improved electrochemical performance with a good charge-discharge capacity and cyclic stability up to 50 cycles at 1C rate, as compared with the without coated LiFePO₄. At 30 °C, the discharge capacity reaches a maximum value of 104.50 and 95.0 mAh g^?1 for graphene oxide-coated LiFePO₄ and without coated LiFePO₄ at 1C rate respectively. These results indicated improved electrochemical performance of pristine LiFePO₄ cathode after coating with graphene oxide.     

Charge storage performance of lithiated iron phosphate/activated carbon composite as symmetrical electrode for electrochemical capacitor

In this study, a symmetric electrochemical capacitor was fabricated by adopting a lithium iron phosphate (LiFePO₄)-activated carbon (AC) composite as the core electrode material in 1.0 M Na₂SO₃ and 1.0 M Li₂SO₄ aqueous electrolyte solutions. The composite electrodes were prepared via a facile mechanical mixing process. The structural properties of the nanocomposite electrodes were characterised by scanning electron microscopy (SEM) and Brunauer–Emmett–Teller (BET) analysis. The electrochemical performances of the prepared composite electrode were studied using cyclic voltammetry (CV), galvanostatic charge–discharge (CD) and electrochemical impedance spectroscopy (EIS). The experimental results reveal that a maximum specific capacitance of 112.41 F/g was obtained a 40 wt% LiFePO₄ loading on an AC electrode compared with that of a pure AC electrode (76.24 F/g) in 1 M Na₂SO₃. The improvement in the capacitive performance of the 40 wt% LiFePO₄–AC composite electrode is believed to be attributed to the contribution of the synergistic effect of the electric double layer capacitance (EDLC) of the AC electrode and pseudocapacitance via the intercalation/extraction of H⁺, OH⁻, Na⁺ and SO₃²⁻ and Li⁺ ions in LiFePO₄ lattices. In contrast, it appears that the incorporation of LiFePO₄ into AC electrodes does not increase the charge storage capability when Li₂SO₄ is used as the electrolyte. This behaviour can be explained by the fact that the electrolyte system containing SO₄²⁻ only exhibits EDLC in the Fe-based electrodes. Additionally, Li⁺ ions that have lower conductivity and mobility may lead to poorer charge storage capability compared to Na⁺ ions. Overall, the results reveal that the AC composite electrodes with 40 wt% LiFePO₄ loading on a Na₂SO₃ neutral electrolyte exhibit high cycling stability and reversibility and thus display great potential for electrochemical capacitor applications.     

A piperidinium-based ionic liquid electrolyte to enhance the electrochemical properties of LiFePO<Subscript>4</Subscript> battery

A piperidinium-based ionic liquid, N-methylpiperidinium-N-acetate bis(trifluoromethylsulfonyl)imide ([MMEPip][TFSI]), was synthesized and used as an additive to the electrolyte of LiFePO₄ battery. The electrochemical performance of the electrolytes based on different contents of [MMEPip][TFSI] has been investigated. It was found that the [MMEPip][TFSI] significantly improved the high-rate performance and cyclability of the LiFePO₄ cells. In the optimized electrolyte with 3 wt% [MMEPip][TFSI], 70 % capacity can be retained with an increase in rate to 3.5 C, which was 8 % higher than that of electrolyte without [MMEPip][TFSI]. For the Li/LiFePO₄ half-cells, after 100 cycles at 0.1 C, the discharge capacity retention was 78 % in the electrolyte without ionic liquid. However, in the electrolyte with 3 wt% [MMEPip][TFSI], it displayed a high capacity retention of 91 %. The good electrochemical performances indicated that the [MMEPip][TFSI] additive would positively enhance the electrochemical performance of LiFePO₄ battery.     

Stability of LiFePO4 in water and consequence on the Li battery behaviour

The stability of LiFePO₄ in water was investigated. Changes upon exposure to water can have several important implications for storage conditions of LiFePO₄, aqueous processing of LiFePO₄-based composite electrodes, and eventually for utilisation in aqueous lithium batteries. A Li₃PO₄ layer of a few nanometers thick was characterised at the LiFePO₄ grains surface after immersion in water, accompanied by an increase of Fe^III percentage in the grains. For first charge–discharge cycles in a lithium battery, no effect was observed on electrochemical performances for a sample of LiFePO₄ immersed for 24 h at a concentration of 50 g L⁻¹ without any pH modification. To limit the aging of LiFePO₄ during aqueous electrode processing, it is advised to reduce the immersion duration, to concentrate the LiFePO₄ suspensions, and not to modify the pH. In addition, since immersion in water mimics an accelerated exposure to air humidity, LiFePO₄ should be stored in a dry atmosphere. Paper presented at the 11th EuroConference on the Science and Technology of Ionics, Batz-sur-Mer, Sept. 9–15, 2007.