Fe3O4磁液的悬浮率测定及稳定性研究

The paper first reported the preparation of ultrafine Fe₃O₄ powder about 8～10nm by improved chemical pre-cipitation method， then turned it into magnetic fluid. The phase analysis， morphology， ultrafine powder size and magnetic property were measured by XRD， TEM and vibrating sample magnetometer(VSM)，respectively. In ad-dition， a new method ， by analyzed the suspending percentage of Fe₃O₄ powder， was introduced to study the effects of concentration， pH value， centrifugal rate and time on the stability of the magnetic fluid.     

草酸盐共沉淀法制备Y1.84La0.16O3纳米粉体

Nanopowder of Y_1.84La_0.16O₃ was prepared by oxalate co-precipitation method. The powder was characterized by TG-DTA, XRD and TEM. The results show that the precursor is Re₂(NO₃)₂(C₂O₄)₂·2H₂O (Re=Y, La), and the Y_1.84La_0.16O₃ nanopowders produced by calcining the precursor at 1 000 ℃ for 4 h are 20～40 nm spherical particles and well dispersed. The powders were with high sintering activity and could be fabricated to transparent ceramic without additive at 1 450～1 550 ℃ in H₂ atmosphere for 3 hours. The total transmission of the transparent ceramic could reach 80%.     

纳米MgNb2O6微波介质陶瓷粉体制备及表征

Nano-crystalline MgNb₂O₆ was prepared using Mg(NO₃)₂·6H₂O, Nb₂O₅, HF and citric acid as raw materials by auto-ignition route. The process involves the formation of a viscous gel by thermal dehydration of the citrate-nitrate solution at about 80 ℃. The auto-ignition (at about 200 ℃) of the gel resulted in a high reactivity powder containing intimate blending of MgNbF₇ and NbF₃. The crystalline phase of MgNb₂O₆ could be formed easily at 700 ℃, which is 400 ℃ lower than that of common solid-state reaction process. The nano-crystalline MgNb₂O₆ (～30 nm) powder with good dispersity could be obtained at 850 ℃.     

预氧化固气法合成LiNiO2的研究

LiNiO₂ was prepared by reaction of stoichiometric amounts of thoroughly-mixed LiOH·H₂O and preoxidation nanometer-scale Ni₃O₂(OH)₄ powders in O₂ at the temperature of 700℃ for 6h. The products were tested by XRD， XPS， SEM and electrochemistry methods. It was shown that product was LiNiO₂ single-phase， and the valence of nickel was +3; the average size of it was 40nm; its initial charge specific capacity is 168mAh·g^-1 and the coulomb efficiency is 90%; the second charge specific capacity is 160mAh·g^-1 and the coulomb efficiency is 96%.     

锂离子电池正极材料LiMn2O4的合成与晶体结构（英）

Spinel LiMn₂O₄ powders were prepared using two-step synthesis method consisting of solid-state reaction method and citrate modified sol-gel method. The effects of the calcination temperature and the Li/Mn ratio of raw materials were studied on the physicochemical and electrochemical properties of the spinel LiMn₂O₄ powders, such as crystallinity, lattice constant and density. The title compound was characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Polycrystalline LiMn₂O₄ powers calcined at 750 ℃ were found to be composed of very uniformly-sized microcrystal with an average particle size of 300 nm. The improvement in electrochemical properties was mainly attributed to the process of re-grinding by absolute alcohol.     

电镀烧结法制备Ti/SnO2-Sb2O4电极的研究

The Ti/SnO₂-Sb₂O₄ electrode has been prepared by the electroplate-sinter method. The effect of SbCl₃ adding amount and sintering temperature on its electrode lifetime and oxygen evolution potential were investigated by means of EDX, SEM and XRD analysis. The results indicated that the electrode appeared the best performance when the SbCl₃ adding amounts was 0.2g and the sintering temperature was 550℃. In optimized conditions Ti substrate was entirely covered by SnO₂-Sb₂O₄ and the combinations among them were tight. Due to the use of electroplate method, the electrical conductivity, the oxygen evolution potential and the electrode lifetime were increased, so the elec-tro-catalytic activity and the electrochemical stability of the prepared electrode were found to be superior.     

准球形α-Fe2O3的形成过程研究

The formation process of pseudo-spherical α-Fe₂O₃ particles obtained through the hydrolysis of 0.01 mol·L^-1 FeCl₃ solution was studied by means of TEM and XRD. The results show that the growth of α-Fe₂O₃ nuclies is through the diffusion mechanism. Although the presence of CTAB in the FeCl₃ solution has no effect on the growth process of pseudo-spheric α-Fe₂O₃ particles, more uniform particles are obtained, and the particles are self-assembled to form two-dimensional ordered structure due to the effect of CTAB. The optical character of these α-Fe₂O₃ particles was investigated, and the band-gap of which is about 2.49 eV.     

MgFe2O4-Fe2O3纳米粉体的软化学合成及电磁学特性

Nano-MgFe₂O₄-Fe₂O₃ magnetic powders were synthesized by citrate gel under microwave irradiation. The structure，particle size distribution，electromagnetic characteristics of nano-MgFe₂O₄-Fe₂O₃ were characterized by using TG-DTA, X-ray, electronic microscope, nano-size measurement and electromagnetism measurement apparatus。The results show that the product is a mixture of MgFe₂O₄ and Fe₂O₃ with average size of 44 nm, tanδ for the product is 0.265 and 0.610 at frequency of 1.0 GHz and 1.8 GHz respectively.     

梯度材料LiNi0.8Co0.2O2的合成与表征

The gradient composite LiNi_0.8Co_0.2O₂ was synthesized using spherical Ni(OH)₂ particle coated by a sol-gel containing cobalt and lithium. The precursor was examined by DSC-TG. The gradient composite was characterized by SEM, EDS, XPS, XRD and ICP-AES. The XPS, EDS and ICP-AES results show that content of cobalt in the surface is higher than in the center of the spherical particle of the gradient composite. The first discharge specific capacity of the gradient composite sintered at 700 ℃ is 187.3 mAh·g^-1.     

Nd2O3添加量对BaTiO3陶瓷介电性能的影响

BaTiO₃ ceramics doped with Nd₂O₃(the additive content was respectively 0.001,0.002,0.003,0.005,0.01,0.03mol)were prepared by Sol-Gel method. Effects of Nd₂O₃ contents on the dielectric constant (ε), the dielectric loss (tanδ) ,the Curie-temperature (T_C) and the resistivity (ρ) of BaTiO₃ ceramic were studied. When Nd₂O₃ content was 0.001mol and 0.002mol, the dielectric constant was increased obviously, but the dielectric loss was also increased. When Nd₂O₃ content was 0.003mol, the dielectric constant was increased, and the dielectric loss was decreased, which was suitable for application in condenser. The resistivity was decreased obviously with the increasing of Nd₂O₃ contents, the resistivity was the smallest when Nd₂O₃ content was 0.001mol. The Curie-temperature was also decreased with the increasing of Nd₂O₃ contents.     

磁性可见光催化剂BiVO4/Fe3O4的制备及催化活性

采用超声法将磁基体Fe3O4和BiVO4复合,制备了易于固液分离的磁性可见光催化剂BiVO4/Fe3O4。采用X射线衍射(XRD)、傅立叶转换红外光谱(FTIR)、紫外-可见漫反射光谱(DRS)、透射电子显微镜(TEM)和磁学性质测量系统(MPMS)对产物进行了表征,并以亚甲基蓝为目标降解物,考察了BiVO4/Fe3O4的可见光催化活性。当BiVO4与Fe3O4质量比为5:1时,BiVO4/Fe3O4的催化活性最高,反应经过5 h,对亚甲基蓝的降解率达到92.0%,而单独使用BiVO4为催化剂,降解率仅为72.5%。这表明Fe3O4不仅起到磁基体的作用,还起到助催化剂的作用。BiVO4/Fe3O4在外加磁场的作用下很容易被分离,撤消外加磁场后,通过搅拌又可重新分散。BiVO4/Fe3O4 3次回收后的降解率仍高于80%。     

Bi2Fe4O9纳米粉体:水热法制备及表征

Bi₂Fe₄O₉ nanoparticles were prepared at low temperature via a facile, one-step hydrothermal synthesis process using iron(Ⅲ) nitrate nonahydrate(Fe(NO₃)₃·9H₂O) and bismuth nitrate pentahydrate (Bi(NO₃)₃·5H₂O) as starting materials and sodium hydroxide (NaOH) as the precipitant and mineralizer. XRD results indicate that the as-prepared nanoparticles are pure Bi₂Fe₄O₉. SEM images reveal that the as-prepared Bi₂Fe₄O₉ nanoparticles have a sheet-like morphology. The Bi₂Fe₄O₉ nanoparticles thus obtained are paramagnetic at room temperature as shown by magnetic measurements.     

磁载光催化剂TiO2/SiO2/Ni0.5Fe2.5O4的制备及其催化氧化性能

采用固相反应法制备磁载体(SiO₂/Ni_0.5Fe_2.5O₄),溶胶-凝胶法得到易于磁分离回收的磁载光催化剂TiO₂/SiO₂/Ni_0.5Fe_2.5O₄。用XRD、SEM、IR和UV-Vis等进行表征。研究了太阳光下催化剂对亚甲基蓝溶液的脱色性能。结果表明,在太阳光下,磁载光催化剂TiO₂/SiO₂/Ni_0.5Fe_2.5O₄可使亚甲基蓝溶液迅速脱色；3次循环使用后脱色率仍为95%以上,回收率为98.8%。     

低温固相反应合成Li3V2(PO4)3正极材料及其性能

利用V₂O₅·nH₂O湿凝胶，LiOH·H₂O，NH₄H₂PO₄和C等作原料，通过低温固相还原反应在550 ℃焙烧12 h制备出Li₃V₂(PO₄)₃正极材料。采用XRD，SEM和电化学测试对Li₃V₂(PO₄)₃样品性能进行研究。XRD研究表明本法所合成的Li₃V₂(PO₄)₃同传统的高温固相反应法所合成的Li₃V₂(PO₄)₃一样同属于单斜晶系结构。SEM测试表明所合成的样品平均粒径大小约为0.5 μm且粒径分布较窄。电化学测试表明以0.2 C的倍率放电时，样品的首次放电容量为130 mAh·g^-1，室温下循环30次后其比容量为124 mAh·g^-1。     

Cu-Sn-P-LiMn2O4纳米复合材料镀层的XPS和AES研究

采用化学复合镀技术，在Q₂₃₅碳钢片表面制备了Cu-Sn-P-LiMn₂O₄纳米复合材料镀层。用扫描电子显微镜(SEM)观察外貌；称重法测定厚度；通过5% NaCl溶液、1% H₂S气体加速腐蚀试验、抗粘性试验及室温氧化试验等多种手段测定其性能。用X-射线光电子能谱(XPS)及俄歇电子能谱(AES)测定其价态及组成。结果表明:Cu-Sn-P-LiMn₂O₄纳米复合材料镀层的性     

纳米钙钛矿LaxSr1-xFe1-yCoyO3复合氧化物的制备和表征

用甘氨酸-硝酸盐燃烧合成法，制备La_xSr_1-xFe_1-yCo_yO₃复合氧化物的陶瓷粉末，对该钙钛矿型氧化物进行了XRD、IR、紫外漫反射光谱及循环伏安曲线分析。结果表明：该复合氧化物粉体平均晶粒为15.3～29.8 nm,为立方和正交晶系。该氧电极具有双功能催化特性，但不完全可逆。对水溶液染料进行光解实验，利用紫外-可见、人工神经网络光度法研究La_xSr_1-xFe_1-yCo_yO₃的催化性能。结果表明：CO²⁺的加入可使La_xSr_1-xFeO₃的光催化活性有所提高，B位离子(Fe³⁺，CO²⁺)改变与加入，使La_xSr_1-xFe_1-yCo_yO₃(x=0.7，0.3；y=0.3，0.9，1)光催化活性高于La_xSr_1-xFeO₃。同时，对5种染料进行紫外光解，在0.75 h，脱色率大于91%，并为动力学一级反应。     

配体交换法制备水中高分散稳定性的多羧基修饰Fe3O4纳米颗粒

采用油相高温分解法制备了粒径可控且单分散的油溶性Fe3O4磁性纳米粒子(MNPs-OA), 并通过配体交换对其表面进行了亲水性修饰, 制备了柠檬酸(CA)、 N-(三甲氧基硅丙基)乙二胺三乙酸钠(SiCOOH)、 丁烷四羧酸(BTCA)和乙二胺四乙酸 (EDTA)四钠4种多羧基配体修饰的水溶性Fe3O4磁性纳米粒子(MNPs-CA, MNPs-SiCOOH, MNPs-BTCA 和MNPs-EDTA), 其中首次选用四羧基配体BTCA和EDTA四钠来修饰Fe3O4磁性纳米粒子(MNPs). 对油溶性MNPs和4种水溶性MNPs的形貌、 结构、 化学组成和磁性能进行了表征, 并对4种多羧基配体修饰的水溶性MNPs在水相中的稳定性和分散性进行了表征. 结果表明, 所得MNPs的平均粒径为15 nm, 具有超顺磁性, 配体交换后的水溶性MNPs具有良好的亲水性, 并在弱酸～碱性很宽的pH范围内具备良好的分散稳定性. 此类多羧基修饰的水溶性MNPs可与适当的阳离子聚电解质进行组装, 从而得到在磁靶向载体和磁共振造影(MRI)显影中具有良好应用前景的磁性自组装微囊.     

Preparation and mechanism of Fe3O4/Au core/shell super-paramagnetic microspheres

In the presence of Fe₃O₄ nano-particles, a new type of super-paramagnetic Fe₃O₄/Au microspheres with core/shell structures was prepared by reduction of Au³⁺ with hydroxylamine. The formation mechanism of the core/shell microspheres was studied in some detail. It was shown that the formation of the complex microspheres can be divided into two periods, that is, surface reaction-controlled process and diffusion-controlled process. The relative time lasted by either process depends upon the amount of Fe₃O₄ added and the initial concentration of Au³⁺. XPS analysis revealed that along with increasing in coating amount, the strength of the characteristic peaks of Au increased, and the Auger peaks of Fe weakened and even disappeared. Size distribution analysis showed that the core/shell microspheres are of an average diameter of 180 nm, a little bit larger than those before coating.     

Ce3+,Tb3+,Eu3+共掺杂Sr2MgSi2O7体系的白色发光和能量传递机理

通过正交试验,采用高温固相法制备了Sr2-x-y-zMgSi2O7∶xCe3+,yTb3+,zEu3+系列样品.使用X射线衍射仪和荧光光谱仪表征了样品的物相和发光性质,并讨论了Ce3+-Tb3+-Eu3+共掺杂Sr2MgSi2O7体系中的能量传递过程.实验结果表明,在327 nm波长激发下,所合成荧光粉的发射峰主要位于387 nm(蓝紫)、542nm(绿)和611 nm(红)处;分别以387,542和611 nm为监控波长,所得激发光谱显示荧光粉在327 nm处有最好的激发.在327 nm光激发下,系列样品发光进入白光区.最优化的荧光粉为Sr1.91MgSi2O7∶0.01Ce3+,0.05Tb3+,0.03Eu3+,其色坐标为(0.337,0.313),是一种潜在的发光二极管(LED)用白色荧光粉.     

α-Fe2O3掺杂对In2O3电导和气敏性能的影响

用化学共沉淀法制备了α Fe2O3掺杂的In2O3纳米晶微粉,研究了α Fe2O3掺杂对In2O3电导和气敏性能的影响. 结果表明, α Fe2O3和In2O3间可形成有限固溶体In2－xFexO3(0≤x≤0.40); Fe3＋对In2O3晶格中In3＋格位的部分取代,大大增强了阴阳离子间的结合力,导致材料中氧空位VO×数骤降、 自由电子的浓度变稀和电导下降. n(Fe3＋):n(In3＋)=5 :5的共沉淀粉于800 ℃下灼烧4 h所得的α Fe2O3掺杂In2O3传感器元件,对45 μmol•L－1 C2H5OH的灵敏度达54.0,为相同浓度干扰气体汽油的8倍多.