Theoretical analysis and heat dissipation of mid-infrared chalcogenide fiber Raman laser

Based on the structure of mid-infrared chalcogenide fiber Raman laser, the nonlinear coupled equations and heat dissipation equations are constructed. The effects of laser parameters including pump power, fiber length, reflectance of output coupler and fiber loss coefficient on laser performance are numerically analyzed. The results show that the Raman laser pumped at 2 μm can operate at high slope efficiency using the optimized structure parameters. In addition, the output laser power decreases dramatically with the increasing of fiber loss coefficient. Moreover, the temperature distributions along the fiber radial and axial directions and the maximum temperature versus launched pump power are calculated according to the heat dissipation equations. The results show that the maximum temperature in the fiber increases dramatically with the increasing launched pump power, which is above 300 °C for launched pump power of 21 W. The above obtained results can be used for theoretical guiding and optimizing design of practical chalcogenide fiber Raman laser.     

利用光纤光栅的高功率掺镱光纤激光器

报道了利用一对光纤光栅作为双包层Yb^3 掺杂光纤激光器的谐振腔，激光二极管光纤模块(LD)进行了抽运，并采用锥形光纤实现了全光纤化结构，获得了高功率双包层光纤激光器。光纤光栅通常是用融接技术实现与双包层光纤的一体化连接的，采用的双包层光纤为内包层为梅花瓣形结构的掺Yb^3 离子的石英光纤，采用的抽运源为中心波长为970nm的半导体激光光纤输出模块，在抽运源电流达到2．4A时，获得了10．8W的光纤激光器单横模输出，输出波长1100．5nm，峰值半峰全宽(FWHM)为0．54nm，激光器斜效率为59％。     

高功率光子晶体光纤激光器实验研究

 从光纤热传导方程出发,研究了不同泵浦光吸收系数对光纤激光器沿光纤长度方向温度分布的影响。结果表明,低吸收系数光纤泵浦端温度相对较低,分布较为平缓,有效减缓光纤的热损伤。根据理论分析结果,实验中选择了吸收系数为1.45 dB/m的掺Yb³⁺双包层光子晶体光纤作为增益介质,在泵浦光功率为560 W时,获得了428.5 W的高功率单模连续输出,斜率效率为76.5%,光束质量因子M²<1.2。由于泵浦端光纤温度较高,实验中对光纤两端进行了主动冷却,并且在离光纤端面约25 cm处的光纤表面温度进行实时测量,结果发现随着泵浦光功率的增加,光纤表面温度均匀增长,最高温度为310 K,温度正常。     

Thermally tunable microfiber knot resonator based erbium-doped fiber laser

A compact and tunable erbium-doped fiber laser is demonstrated using a highly doped fiber and a microfiber knot resonator (MKR) structure which is laid on the surface of a small peltier. The MKR functions as both a reflector and a tunable filter where tunability is achieved by varying the temperature of the resonator by heating the peltier. A stable laser output is achieved at the 1533 nm region with an optical signal to noise ratio (OSNR) of 27 dB using a 65 mW of 980 nm pump power. The operating wavelength of the laser can be tuned from 1532.60 nm to 1533.49 nm as the temperature is increased from the room temperature of 24 to 90 °C. It is observed that the operating wavelength shifts to a longer wavelength as the temperature increases with an efficiency of 12.4 pm/°C. This is due to the thermally induced optical phase shift attributable to the changes in effective refractive index and optical path length of the MKR loop.     

169 MHz repetition frequency all-fiber passively mode-locked erbium doped fiber laser

Passively mode-locked stretched-pulse erbium fiber laser is presented. With all-fiber configuration 111 fs pulses were achieved with the fundamental repetition rate of 169 MHz and an average output power of more than 30 mW. Proposed setup shows excellent stability, reliability and ‘turn-key’ operation. The impact of the pump power on laser parameters is described.     

基于光纤激光器的中红外差频多波长激光产生

针对由YDFL和EDFL作为基频光源的QPM-DFG激光系统,利用PPMgLN晶体的色散关系及其温度特性,有效拓宽了QPM波长接受带宽.模拟结果表明,当采用1550和1060 nm波段的EDFL和YDFL分别作为DFG的信号和抽运光源时,对于相同的中红外波段,满足QPM条件所允许的抽运光波长变化范围远大于信号光波长变化范围.当固定信号光波长为1560 nm时,对于给定的晶体温度,1060 nm波段抽运光的QPM接受带宽超过17 nm,对应于中红外差频光带宽可约180 nm.采用多波长YDFL作为抽运源,单 关键词： 差频产生 准相位匹配 多波长中红外 光纤激光器     

1150 nm High-Power Fiber Laser Oscillator Pumped by 976 nm Laser Diode

We present an all-fiber 1150 nm Yb-doped fiber laser oscillator pumped by a 976 nm laser diode. To suppress amplified spontaneous emission and avoid parasitic laser oscillation, we propose a long-length gain fiber and a high-reflectivity output fiber Bragg grating in the fiber laser oscillator. The 1150 nm band single-mode fiber laser with output power of 20.5 W is demonstrated at room temperature. The optical-to-optical conversion efficiency ranges up to 51.6% at the maximum output. The central wavelength of the fiber laser oscillator is 1150.35 nm, and its 3 dB spectral width is 0.72 nm. No evidence of amplified spontaneous emission, residual pump light, or parasitic laser oscillation were observed in the experiments. The high-power 1150 nm fiber laser oscillator can be used as a pump source in the development of a 3 μm Ho-doped fiber laser.     

基于光纤中SBS相位共轭的自调Q光纤激光器

分析了利用光纤中的受激布里渊散射(stimulated Brillouin scattering,SBS)相位共轭效应进行激光腔内调Q,产生ns量级脉冲激光的原理,并对利用该效应产生的激光脉冲波形和脉冲形成过程进行了数值模拟,得到的脉冲波形与SBS相位共轭反射率随时间变化曲线基本一致,表明利用光纤中的SBS相位共轭作用调Q具有可行性.据此,对采用单模光纤(single-mode fiber,SMF)作为SBS池的Er³⁺掺杂调Q光纤激光器进行实验研究.当单模光纤长度为1.5 m时,在45 mW的光抽运功率下得到脉宽约2.6ns,脉冲周期58.23ns,平均功率7.35mW的激光脉冲.进一步的研究表明:激光器中相位共轭镜的形成与SBS介质长度有关,SBS介质过长,斯托克斯线之间无固定的相位关系,不能形成相干叠加,SBS相位共轭腔不能形成;SBS介质过短,腔内正交偏振模光子寿命的改变使脉冲出现双峰现象.脉冲形成后其属性只与SBS动态属性有关.     

多光束纳秒紫外激光制作硅表面微结构

使用波长351 nm的半导体泵浦全固态脉冲激光器（DPSSL）作为光源,经过位相光栅分束,形成干涉光场,在硅表面直接刻蚀微结构,制作了周期为0.55 µm,槽深可达55 nm的一维微光栅和周期为1.25 µm,刻蚀深度45nm的正交微光栅结构。给出了微光栅形貌结构的扫描电子显微镜(SEM)和原子力显微镜(AFM)的测量结果。正交微光栅的一级衍射效率在1.8%到6.3%之间。该研究是改变硅表面微结构,优化硅材料特性的一种新方法,并扩展了大功率激光刻蚀在表面微加工领域的应用。     

The optimum length of linear cavity Yb-doped double-clad fiber laser

In order to improve the performance of the double-clad fiber laser, the optimum laser length needs to be estimated prior to the experiment. Previous expressions for the optimum length of fiber laser have been established under some assumptions, such as the output power without laser scattering loss and the pump power without reflection in the output-end. In this work, the issue of optimum laser length has been analyzed theoretically based on the strongly pumped fiber laser model. An extended expression for the optimum length of the linear cavity Yb³⁺-doped double-clad fiber laser is obtained. The respective effects of the laser scattering loss, the pump power, the Yb³⁺ dopant concentration, and the pump reflection on the optimum laser length are identified.     

Dual-order Raman fiber laser with suppressed low-frequency pump-to-stokes RIN transfer

By employing an output-power clamping technique, a dual-order Raman fiber laser (RFL) is theoretically presented with suppressed low-frequency relative-intensity-noise (RIN) transfer from pump sources to both first- and second-order Stokes output. Their powers can be easily tuned in a large dynamic range. Furthermore, the second-order output power can be individually controlled, which makes it flexible to adjust the ratio of the first- to second-order output power. In addition, the stabilization of low-power second-order output is also accomplished in the RFL setup. These properties fit the proposed RFL for use as dual-order pump sources in Raman fiber amplifiers.     

Optimization of erbium-doped fiber MOPA laser

An erbium-doped fiber laser (EDFL) constructed in a master oscillator and power amplifier (MOPA) configuration is analyzed. The pump powers for the fiber cavity laser and the booster amplifier stages are managed properly to achieve maximal pump conversion efficiency. Our design achieves a pump conversion efficiency of 91.4%, corresponding to a quantum efficiency of 96.6%, for a 1565.8 nm MOPA laser pumped by a total power of 300 mW at 1480 nm. The optimized MOPA laser shows a 25% enhancement in the pump conversion efficiency, compared to a non-MOPA fiber laser. A side lobe suppression ratio of 48 dB for the optimized MOPA laser is observed.     

基于光纤中超短脉冲非线性传输机理与特定光谱选择技术的多波长飞秒激光的产生

高集成、高可靠性宽调谐飞秒激光源在超快光谱学、量子光学及生物成像等研究与应用领域具有重要价值.如在生物多光子显微成像中,具有适中能量的宽调谐飞秒激光源不仅可满足多种生物组织荧光激发所需的峰值功率与激发波长,而且也可以显著提升非线性荧光产生效率、成像分辨率以及增大成像穿透深度.采用自主研发的高可靠性全保偏光纤飞秒激光器作为抽运源,基于低色散光纤中高峰值功率飞秒激光脉冲非线性传输引起的光谱加宽机制,本文开展了多波长全光纤飞秒激光产生技术研究.通过采用中心波长在980, 1000,1050, 1070与1100 nm的带通滤波片选择性地对单模光纤输出光谱中最左边与最右边光谱旁瓣进行滤波,在上述中心波长处分别可获得203, 195, 196, 187与194 fs的激光输出.本文提出的基于全光纤飞秒激光脉冲在单模光纤中非线性传输引起的光谱加宽机制与特定光谱选择技术的实验方案为高集成、高可靠性宽调谐飞秒激光源的实现提供了新的研究途径.     

Multi-wavelength generation using a bismuth-based EDF and Brillouin effect in a linear cavity configuration

The generation of a multiple wavelength source using a bismuth-based erbium-doped fiber (Bi-EDF) in a linear cavity configuration is demonstrated. The configuration uses a pair of optical circulators at the input and output ends of the cavity to form a resonator for multi-wavelength generation in conjunction with optical couplers to inject the Brillouin pump (BP) and to tap the output at the two ends. The Brillouin erbium fiber laser (BEFL) comb with a 2.15 m of Bi-EDF has a wavelength spacing of 0.09 nm and operates in long-wavelength (L-) band region. A stable output laser comb of 50 lines is obtained at a BP of 1568.2 nm and 5 dBm and two 1480 nm pumps at 120 mW. The injected BP wavelength and power as well as the 1480 nm pump powers have a great effect on the number of lines and output power of the BEFL. This configuration is compact due to the use of the significantly shorter Bi-EDF as the linear gain medium, and can be made more compact by replacing the single-mode fiber with highly non-linear fibers such as holey fibers.     

LD泵浦掺铥(Tm3+)光纤激光器的数值分析

首先从掺铥光纤激光器的速率方程和光传输方程出发,建立数学模型,通过Matlab软件进行数值计算,分析了泵浦光和激光沿光纤的分布以及各能级离子数的变化.在不同掺杂浓度下,研究了小信号增益与入纤泵浦功率的关系以及泵浦光和激光功率与增益介质长度的关系.在不同泵浦功率下,研究了输出功率与输出耦合镜反射率的关系.进一步对不同泵浦吸收系数,研究了斜率效率和泵浦阈值与光纤长度的关系.分析结果表明存在最佳光纤长度和最佳耦合输出透过率,使得激光输出功率达到最佳值.     

光纤光栅F-P标准具选模单频环形腔光纤激光器

 讨论了光纤光栅法布里-珀罗(F-P)标准具选模光纤激光器的单频运转原理，并研制了全光纤结构单频掺Er³⁺光纤环形激光器。实验中采用两个976 nm激光二极管双向泵浦作为泵浦源，高掺杂浓度掺Er³⁺光纤作为增益介质，以行波腔消除空间烧孔效应，利用光纤光栅F-P标准具窄带选模特性，当泵浦光功率为36 mW时，得到了稳定的单频激光输出。实验中使用了长5和3 m的掺杂光纤，在泵浦光功率为145 mW时输出功率分别为19和42 mW，光-光转换效率分别为13%和29%，斜率效率分别达到了16%和33%。输出谱线3 dB带宽0.01 nm，无跳模现象。     

高功率梯度掺杂增益光纤温度特性理论研究

在高功率光纤激光器中, 增益光纤的热效应是限制激光功率进一步提高的重要因素之一. 为了降低增益光纤的最高温度, 提出了一种通过改变增益光纤的掺杂浓度分布, 分散光纤激光的热效应, 从而提高激光输出功率的方法. 基于速率方程模型和热传导模型, 在光纤激光放大器输出功率大致相当的情况下, 对几种不同掺杂方式下增益光纤中的热分布和放大器的输出功率进行了数值模拟. 研究结果表明: 增益光纤的梯度掺杂可以优化光纤中的温度分布并提高光纤熔接点的稳定性; 同时兼具提高输出光束的光束质量、抑制光纤中非线性效应和模式不稳定的效果, 是提高光纤激光放大器输出功率切实可行的办法. 研究结果可以为高功率光纤激光器中增益光纤的设计提供一定的参考.     

C-band continuously tunable lasers using tunable fiber Bragg gratings

We report the development of a ring tunable fiber laser based on tunable fiber Bragg gratings (TFBG) integrated with an optical circulator. The TFBG is embedded inside a 3-piont bending device for wavelength tuning. The tunable laser operating in the C-band has power variation, tuning resolution, tuning range and laser line width of ±0.5 dB, 0.5 nm, 25.0 nm and less than 0.05 nm, respectively. As 40 mW of pump power is used, the ring tunable laser has a side mode suppression ratio of 60 dB and a power conversion efficiency of 25%. These specifications ensure the high-quality operation of a tunable laser.     

体布拉格光栅外腔半导体激光器光谱特性研究

用体布拉格光栅(VBG)作为反馈元件与瓦级半导体激光器(LD)以及快轴准直柱透镜构成一个可以将半导体激光器的工作波长稳定在体布拉格光栅布拉格波长处的外腔激光器。测量了体布拉格光栅外腔激光器的波长稳定性与其工作电流、热汇温度、激光束准直装置等因素的关系。分析了波长稳定效果与半导体激光器增益谱特性、外腔结构参量等因素的关系。研究表明,在相同的工作电流、热汇温度下,当准直柱透镜直径为0.4 mm时的波长稳定效果较好;在此情况下,当热汇温度控制在30℃,工作电流从0.5 A增加到1.5 A的测量范围内,以及当工作电流固定在1.5 A,热汇温度从20℃增加到35℃时,测得的光谱特性表明,半导体激光器的工作波长可以很好地稳定在体布拉格光栅的布拉格波长处。与该激光器在同样条件下自由运转的光谱比较,可以看到,自由运转激射波长与体布拉格光栅的布拉格波长差值小于2.6 nm情况下,可以获得很好的波长稳定效果。实验也表明,当该值大于4.8 nm时波长稳定效果变差。     

非线性吸收诱导掺镱光纤激光器中的光学双稳

研究了在掺镱光纤激光器中观察到的光学双稳态现象.激光信号光和驻留泵浦光的双稳特性来源于激光器在小信号和增益饱和两种情况下,掺镱光纤对信号的非线性吸收导致的激光器内腔非线性损耗.同时分析了把泵浦光中的光学双稳行为通过分叉的腔结构扩展到切换式双波长光纤激光器的可行性.