The delta phase of bismuth oxide (δ-Bi2O3) is an important metal oxide due to its highest conductivity of any oxide material. However, it is only stable over a narrow high temperature range, and thus, incorporation of small, high-valence cation is a prerequisite for stabilizing its cubic structure to room temperature. The δ-Bi2O3 is also known to have low photocatalytic activity because of its low conduction band edge. As a consequence, the conduction band electrons cannot be consumed by the dissolved oxygen to produce superoxide radicals. Herein, for the first time, the δ-Bi2O3 has been successfully synthesized through a facile hydrothermal route without addition of any dopant. The as-synthesized δ-Bi2O3 shows ultrahigh photocatalytic activity for cylindrospermopsin decomposition. Within only 20 min of UV irradiation, the degradation efficiency for cylindrospermopsin by 0.5 g/L of the δ-Bi2O3 with a cylindrospermopsin concentration of 5 mg/L reaches 98%. Restricted charge carrier recombination and effective consumption of the conduction band electrons are behind such an unprecedented high photocatalytic activity of the δ-Bi2O3.
Electrochemical reduction of carbon dioxide is one of the methods which have the capability to recycle CO2 into valuable products for energy and industrial applications. This research article describes about a new electrocatalyst “reduced graphene oxide supported gold nanoparticles” for selective electrochemical conversion of carbon dioxide to carbon monoxide. The main aim for conversion of CO2 to CO lies in the fact that the latter is an important component of syn gas (a mixture of hydrogen and carbon monoxide), which is then converted into liquid fuel via well-known industrial process called Fischer-Tropsch process. In this work, we have synthesized different composites of the gold nanoparticles supported on defective reduced graphene oxide to evaluate the catalytic activity of reduced graphene oxide (RGO)-supported gold nanoparticles and the role of defective RGO support towards the electrochemical reduction of CO2. Electrochemical and impedance measurements demonstrate that higher concentration of gold nanoparticles on the graphene support led to remarkable decrease in the onset potential of 240 mV and increase in the current density for CO2 reduction. Lower impedance and Tafel slope values also clearly support our findings for the better performance of RGOAu than bare Au for CO2 reduction.
5-Sulfosalicylic acid (SFSA) functionalized mesoporous silica nanocomposites (SBA/APTS/SFSA) were synthesized by post grafting technique for selective debenzylation of 1-benzyloxy-4-methoxy benzene. The uniform incorporation of SFSA inside the mesoporous SBA-15 framework was confirmed by standard characterization techniques (PXRD, adsorption studies, FT-IR, etc.). Total surface area, pore size and pore volume of the SBA/APTS/SFSA catalysts decreased with increase in the concentration of SFSA confirming the uniform insertion of SFSA into mesoporous SBA-15 matrix. Catalytic activity studies showed highest conversion and selectivity of the desired product on SBA/APTS/SFSA catalyst compared to homogeneous SFSA and other solid support (Al2O3 and SiO2). All the reaction parameters such as reaction time, reaction temperature and catalyst weight were optimized under environmental friendly conditions. Finally, the possible mechanism of the reaction was explained.
Rare-earth-based infinite coordination polymer (RE-ICP) spheres with diameters ranging from 50 nm to 2 μm have been prepared using meso-2,3-dimercaptosuccinic acid (DMSA) as ligand under hydrothermal conditions. RE2O2SO4 microspheres with similar morphology were obtained by calcining the corresponding RE-ICP spheres. However, as for Ce-ICP and Sc-ICP, CeO2 and Sc2O3 were obtained. The products were characterized using X-ray diffraction, scanning electron microscopy, thermogravimetric analysis, infrared spectroscopy, laser Raman spectrometry, and energy-dispersive X-ray spectrum. Elemental analysis and inductive coupled plasma atomic emission spectrometer were adopted to study the composition of the Eu-ICP. To explore their potential applications, several samples of the products were selected and their properties were investigated. The Eu-ICP and Eu2O2SO4 microspheres give strong red emissions when excited with a 394-nm ultraviolet light. Furthermore, the Eu-ICP displays a high selectivity for Fe(III). The obtained CeO2 has a strong absorption in the UV region and the Gd2O2SO4 microspheres show paramagnetic behavior.
Minimizing of the boundary friction coefficient is critical for engine efficiency improvement. It is known that the tribological behavior has a major role in controlling the performance of automotive engines in terms of the fuel consumption. The purpose of this research is an experimental study to minimize the boundary friction coefficient via nano-lubricant additives. The tribological characteristics of Al2O3 and TiO2 nano-lubricants were evaluated under reciprocating test conditions to simulate a piston ring/cylinder liner interface in automotive engines. The nanoparticles were suspended in a commercially available lubricant in a concentration of 0.25 wt.% to formulate the nano-lubricants. The Al2O3 and TiO2 nanoparticles had sizes of 8–12 and 10 nm, respectively. The experimental results have shown that the boundary friction coefficient reduced by 35–51% near the top and bottom dead center of the stroke (TDC and BDC) for the Al2O3 and TiO2 nano-lubricants, respectively. The anti-wear mechanism was generated via the formation of protective films on the worn surfaces of the ring and liner. These results will be a promising approach for improving fuel economy in automotive.
Nano-octahedra of cobalt ferrite CoxFe3???xO4 (1?≤?x?<?2), with a broad size distribution around 15–20 nm, were synthesized by a hydrothermal method using nitrates as precursors. For the first time, single-phased nano-octahedra of cobalt-rich ferrite CoxFe3???xO4 (x?=?1.5) were synthesized. The nano-octahedra are crystallized in a normal spinel structure, with tetrahedral sites occupied by Co2+. This specific octahedral shape was obtained with anionic, cationic, and nonionic surfactants. The nature of the surfactant influenced the chemical composition of the powder and the size of the nano-octahedra. The {100} truncation of the octahedra is more pronounced for the small particles. For the first time, single-phased nanoparticles with as much as x?=?1.8 cobalt were synthesized with ethylene glycol as solvent. These nanoparticles, around 8 nm in size, have no specific shape and possess a lacunar spinel structure similar to maghemite. The samples were characterized by X-ray diffraction, transmission electron microscopy, and energy-dispersive spectroscopy.
Abstract The anisotropic gold and spherical–quasi-spherical silver nanoparticles (NPs) were synthesized by reducing aqueous chloroauric
acid (HAuCl4) and silver nitrate (AgNO3) solution with the extract of phyllanthin at room temperature. The rate of reduction of HAuCl4 is greater than the AgNO3 at constant amount of phyllanthin extract. The size and shape of the NPs can be controlled by varying the concentration of
phyllanthin extract and thereby to tune their optical properties in the near-infrared region of the electromagnetic spectrum.
The case of low concentration of extract with HAuCl4 offers slow reduction rate along with the aid of electron-donating group containing extract leads to formation of hexagonal-
or triangular-shaped gold NPs. Transmission electron microscopy (TEM) analysis revealed that the shape changes on the gold
NPs from hexagonal to spherical particles with increasing initial concentration of phyllanthin extract. The Fourier transform
infrared spectroscopy and thermogravimetric analyses reveal that the interaction between NPs and phyllanthin extract. The
cyclic voltammograms of silver and gold NPs confirms the conversion of higher oxidation state to zero oxidation state.
Graphical abstract Anisotropic gold and silver nanoparticles were synthesized by a simple procedure using phyllanthin extract as reducing agent.
The rate of bioreduction of AgNO3 is lower than the HAuCl4 at constant concentration of phyllanthin extract. The required size of the nanoparticles can be prepared by varying the concentration
of phyllanthin with AgNO3 and HAuCl4.
相似文献
Ruthenium/reduced graphene oxide nanocomposites (Ru/rGO NCs) were synthesized via an electrostatic self-assembly approach. Polyvinylpyrrolidone (PVP) stabilized and positively charged metallic ruthenium nanoclusters about 1.2 nm were synthesized and uniformly loaded onto negatively charged graphene oxide (GO) sheets via strong electrostatic interactions. The as-prepared Ru/rGO NCs exhibited superior performance in catalytic hydrolysis of sodium borohydride (NaBH4) to generate H2. The hydrogen generation rate was up to 14.87 L H2 min?1 gcat?1 at 318 K with relatively low activation energy of 38.12 kJ mol?1. Kinetics study confirmed that the hydrolysis of NaBH4 was first order with respect to concentration of catalysts. Besides, the conversion of NaBH4 remained at 97% and catalytic activity retained more than 70% after 5 reaction cycles at room temperature. These results suggested that the Ru/rGO NCs have a promising prospect in the field of clean energy.
Active iron-containing nanosized components have been formed on the lignin surface. The metal was deposited on the lignin from an ethanol solution of Fe(acac)3 and from a colloid solution of iron metal particles obtained beforehand by metal vapor synthesis. These active components are able to absorb microwave radiation and are suitable for microwave-assisted high-rate dehydrogenation and dry reforming of lignin without addition of a carbon adsorbent, as a supplementary radiation absorbing material, to the feedstock. The dependence of the solid lignin heating dynamics on the concentration of supported iron particles was investigated. The threshold Fe concentration equal to 0.5 wt.%, providing the highest rate of sample heating up to the reforming and plasma generation temperature was identified. The microstructure and magnetic properties of iron-containing nanoparticles supported on lignin were studied before and after the reforming. The Fe3O4 nanoparticles and also core-shell Fe3O4@γ-Fe-С nanostructures are formed during the reforming of lignin samples. The catalytic performance of iron-based nanoparticles toward the lignin conversion is manifested as increasing selectivity to hydrogen and syngas, which reaches 94% at the Fe concentration of 2 wt.%. It was found that with microwave irradiation under argon, hydrogen predominates in the gas. In the СО2 atmosphere, dry reforming takes place to give syngas with the СО/Н2 ratio of ~?0.9. In both cases, the degree of hydrogen recovery from lignin reaches 90–94%.
Graphical abstract The microwave-supported deposition of iron on the lignin surface gives active well defined nanoparticles Fe3O4 and also core-shell Fe3O4@γ-Fe-С nanostructures. These nanocomponents provide for high-rate microwave-assisted dehydrogenation and dry reforming of lignin.
Small core-shell Fe3O4@Pd superparamagnetic nanoparticles (MNPs) were obtained with good control in size and shape distribution by metal-complex thermal decomposition in organic media. The role of the stabilizer in the synthesis of MNPs was studied, employing oleylamine (OA), triphenylphosphine (TPP) and triphenylamine (TPA). The results revealed that, among the stabilizer investigated, the presence of oleylamine in the reaction media is crucial in order to obtain an uniform shell of Pd(0) in Fe3O4@Pd MNPs of 7?±?1 nm. The synthesized core-shell MNPs were tested in Pd-catalyzed Heck-Mizoroki and Suzuki-Miyaura coupling reactions and p-chloronitrobenzene hydrogenation. High conversion, good reaction yields, and good TOF values were achieved in the three reaction systems with this nanocatalyst. The core-shell nanoparticle was easily recovered by a simple magnetic separation using a neodymium commercial magnet, which allowed performing up to four cycles of reuse.
A nitrogen-doped reduced graphene oxide (N-RGO) nanosheet was synthesized by a simple hydrothermal method and characterized by X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy, and scanning electrode microscopy. After being deposited as counter electrode film for dye-sensitized solar cells (DSSCs), it is found that the synthesized N-RGO nanosheet has smaller charge-transfer resistance and better electrocatalytic activity towards reduction of triiodide than the reduced graphene oxide (RGO) nanosheet. Consequently, the DSSCs based on the N-RGO counter electrode achieve an energy conversion efficiency of 4.26%, which is higher than that of the RGO counter electrode (2.85%) prepared under the same conditions, and comparable to the value (5.21%) obtained with the Pt counter electrode as a reference. This N-RGO counter electrode offers the advantages of not only saving the cost of Pt itself but also simplifying the process of counter electrode preparation. Therefore, an inexpensive N-RGO nanosheet is a promising counter electrode material to replace noble metal Pt.
Graphical abstract A nitrogen-doped reduced graphene oxide nanosheet was synthesized by a simple hydrothermal method, which is a promising counter electrode material to replace noble metal Pt.
Carbon-coated ZnFe2O4 spheres with sizes of ~110–180 nm anchored on graphene nanosheets (ZF@C/G) are successfully prepared and applied as anode materials for lithium ion batteries (LIBs). The obtained ZF@C/G presents an initial discharge capacity of 1235 mAh g?1 and maintains a reversible capacity of 775 mAh g?1 after 150 cycles at a current density of 500 mA g?1. After being tested at 2 A g?1 for 700 cycles, the capacity still retains 617 mAh g?1. The enhanced electrochemical performances can be attributed to the synergetic role of graphene and uniform carbon coating (~3–6 nm), which can inhibit the volume expansion, prevent the pulverization/aggregation upon prolonged cycling, and facilitate the electron transfer between carbon-coated ZnFe2O4 spheres. The electrochemical results suggest that the synthesized ZF@C/G nanostructures are promising electrode materials for high-performance lithium ion batteries.
In this study Pt, Re, and SnO2 nanoparticles (NPs) were combined in a controlled manner into binary and ternary combinations for a possible application for ethanol oxidation. For this purpose, zeta potentials as a function of the pH of the individual NPs solutions were measured. In order to successfully combine the NPs into Pt/SnO2 and Re/SnO2 NPs, the solutions were mixed together at a pH guaranteeing opposite zeta potentials of the metal and oxide NPs. The individually synthesized NPs and their binary/ternary combinations were characterized by Fourier transform infrared spectroscopy (FTIR) and scanning transmission electron microscopy (STEM) combined with energy dispersive X-ray spectroscopy (EDS) analysis. FTIR and XPS spectroscopy showed that the individually synthesized Pt and Re NPs are metallic and the Sn component was oxidized to SnO2. STEM showed that all NPs are well crystallized and the sizes of the Pt, Re, and SnO2 NPs were 2.2, 1.0, and 3.4 nm, respectively. Moreover, EDS analysis confirmed the successful formation of binary Pt/SnO2 and Re/SnO2 NP, as well as ternary Pt/Re/SnO2 NP combinations. This study shows that by controlling the zeta potential of individual metal and oxide NPs, it is possible to assemble them into binary and ternary combinations.
A novel nano-size MnxOy/clinoptilolite catalyst of high activity for propane-SCR reaction of NOx at low temperatures has been synthesized by a hydrothermal method in a temperature range of 80–180 °C. The optimum synthesis temperature resulting in maximum NOx conversion was 150 °C. An optimum manganese oxide loading of 0.2 wt.% results in the best catalytic behavior (71% NOx conversion). All catalysts exhibited an optimal propane-SCR reaction temperature of 200 °C. The optimum catalyst produces no detectable CO (GHSV 27,000 h) at 200 °C. Manganese in the optimum catalyst exists as Mn2+ (37.8%), Mn3+ (14.2%), and Mn4+ (48%).
Graphical abstract Flake-like manganese oxide nanostructures (indicated by an arrow in the TEM picture) next to the clinoptilolite zeolite sheet-like crystals result in a promising low-temperature propane-selective catalytic reduction of NOx.
Nitrilimine cycloadditions to ethylenes, acetylenes, and activated nitriles have been exploited in the presence of catalytic amounts of oleic-acid-coated iron oxide nanoparticles (diameter?=?11.9?±?1.0 nm). The reactions were fully regioselective with monosubstituted ethylenes and ethyl cyanoformiate, while mixtures of cycloadducts were obtained in the presence of methyl propiolate. The intervention of iron oxide nanoparticles allowed carrying out the cycloadditions at milder conditions compared to the metal-free thermal processes. A labile intermediate has been proposed to explain this behavior.
Graphical abstract Nitrilimine cycloadditions to ethylenes, acetylenes, and activated nitriles have been exploited in the presence of catalytic amounts of oleic-acid-coated iron oxide nanoparticles.
In this paper, the green synthesis of fluorescent carbon dots (CDs) via one-step hydrothermal treatment of cornstalk was investigated. This approach is facile, economical, and effective. The obtained CDs with an average diameter of 5.2 nm possess many excellent properties such as emitting blue fluorescence under UV light (365 nm), high monodispersity, good stability, excellent water dispersibility, and absolute quantum yield of 7.6%. Then, these CDs were used as sensing probes for the detection of Fe2+ and H2O2 with detection limits as low as 0.18 and 0.21 μM, respectively. This sensing platform shows advantages such as high selectivity, good precision, rapid operation, and avoiding the precipitation of iron oxyhydroxides.
Addition reaction between C60 and ethylenediamine occurred at room temperature in an ambient condition. C60-ethylenediamine adduct particles were prepared by mixing toluene solutions of C60 and ethyelenediamine. Average diameter of the C60-ethylenediamine adduct particles was changed non-linearly according to the reaction time, which were observed using transmission electron microscopy. Early stage of the reaction, the diameter of the adduct particles was changed from about 250 to about 430 nm. Then, the size of the adduct particles was converged to about 300 nm. During this addition reaction, the crystalline sizes of adduct particles were constant about 2–3 nm, regardless of the sizes of the adduct particles, which were determined by X-ray diffraction measurement.
The aim of this work was to investigate the possibility of covalent cross-linker-free, polyelectrolyte complex formation at the nanoscale between alginic acid (as sodium alginate, ALG) and protamine (PROT). Optimisation of the self-assembly conditions was performed by varying the type of polymer used, pH of component solutions, mass mixing ratio of the components and the speed and order of component addition on the properties of complexes. Homogenous particles with nanometric sizes resulted when an aqueous dispersion of ALG was rapidly mixed with a solution of PROT. The polyelectrolyte complex between ALG and PROT was confirmed by infrared spectroscopy. To facilitate incorporation of drugs soluble at low pH, pH of ALG dispersion was decreased to 2; however, no nanoparticles (NPs) were formed upon complexation with PROT. Adjusting pH of PROT solution to 3 resulted in the formation of cationic or anionic NPs with a size range 70–300 nm. Colloidal stability of selected alginic acid low/PROT formulations was determined upon storage at room temperature and in liquid media at various pH. Physical stability of NPs correlated with the initial surface charge of particles and was time- and pH-dependent. Generally, better stability was observed for anionic NPs stored as native dispersions and in liquids covering a range of pH.
CeO2 and Fe2O3 co-modified titanate nanosheet (Fe2O3/CeO2@TNS) was prepared by one-pot hydrothermal method; the photocatalyst exhibited large surface area with CeO2 and Fe2O3 particles well dispersed on the surface. The results of XRD, BET, and Raman proved that the CeO2 and Fe2O3 introduced in the TNS influenced its structure evolution from 3D to 2D. The modification resulted in a shift of the absorption edge toward a longer wavelength and the band gap reduced to 2.87 eV. The three-component systems performed excellent photocatalytic activity and cycle stability on phenol and methyl blue (MB) solution under sunlight; nearly total phenol and MB were degraded in dozens of minutes. And the reaction rate constant (K) of Fe2O3/CeO2@TNS on phenol degradation was 1.77, 3.25, 4.88, and 13-fold of Fe2O3@TNS, CeO2@TNS, bare TNS, and P25, respectively. The enhanced photocatalytic activity could be ascribed to the efficient separation of photogenerated pairs through the formation of tandem n-n-n heterojunction among the three-component systems. This work will be useful for the design of other tandem n-n-n heterojunction photocatalytic systems for application in energy conversion and environmental remediation.
This work reported a novel kind of CdTe quantum dot (QD) decorated mesoporous SiO2 (m-SiO2/QD) hybrid hollow nanoparticles for carrying photodynamic therapy (PDT) reagent. Both rod-like and spherical nanoparticles were prepared by using different shaped templates. Due to the porous shell and hollow interior, the hybrid m-SiO2/QD hollow nanorod with 360 nm long and 120 nm in diameter was selected for carrying zinc(II) phthalocyanine (ZnPc) photosensitizing molecules (61 mg/g) since the generated reactive 1O2 could be easily delivered out of the hollow particles through the porous shell (BET area 251 cm2/g). It was found that the m-SiO2/QD-ZnPc hollow nanorods exhibited a good PDT activity and showed effective photocytotoxicity for the cancer cells. Because of the porous nature, fluorescence characteristic, and excellent storage ability, the m-SiO2/QD hybrid hollow particles possessed broad potential in the fluorescent labeled PDT.
Graphic abstract m-SiO2/QD hybrid hollow particles with different morphologies could be successfully synthesized by using the templating method and they could be used as carriers for photodynamic therapy reagents.
