Electrochemical generation of manganese (III) at glassy carbon electrode in acetic acid

Conditions were established for the electrochemical generation of manganese(III) at glassy carbon in acetic acid. In the oxidation of manganese-(II) in potassium acetate supporting electrolyte high current efficiencies were achieved in a wide range of current densities at the working electrode, whereas in the presence of sodium perchlorate a successful generation of manganese(III) could be performed only at low current densities. With increasing content of water in the anolyte the amount of generated manganese (III) was abruptly decreased and its stability in the solution was diminished. Procedures are given for a successful coulometric titration of reducing substances with anodically generated manganese (III); biamperometric, potentiometric and bipotentiometric methods for the location of the end-point were employed. The error of the determinations did not exceed ± 2%.     

An electrode for the coulometric generation of hydrogen ion

The anodic generation of hydrogen ion on bright platinum in 1.0M sodium perchlorate is not quantitative owing to the formation of a chemical species With oxidizińg properties, presumably a peroxydiperchlorate, but 100% current efficiency can be obtained in the anodic generation of hydrogen in 0.25M sodium hydrazinium sulphate, Na(N(2)H(5))SO(4). Five hydrogen ions are formed for each four electrons passed. The efficiency of this "hydrazine-platinum anode" has been demonstrated by the high-precision coulometric titration of tris(hydroxymethyl)aminomethane.     

Extraction with long-chain amines--VI. Separation of manganese as Mn(CNS)4-(6) complex and its complexometric determination in calcareous material

Manganese is quantitatively extracted into a benzene solution of trioctylmethyl-ammonium chloride from a solution at least 0.25M in potassium thiocyanate and at pH 2.5-7. After stripping into dilute ammonia containing triethanolamine (TEA) and hydroxylamine hydrochloride, manganese is determined by EDTA titration. Calcium and magnesium are not extracted even in traces. Iron is co-extracted with manganese and is masked with TEA during the stripping. Aluminium also does not interfere. In the aqueous phase, after the extraction of manganese, calcium or magnesium can be determined by the usual EDTA titration. The method described permits highly selective individual determination of manganese and calcium and/or magnesium in all materials rich in manganese.     

金纳米颗粒@碳微球的制备及其电化学检测汞离子性能研究

本文研究了金纳米颗粒@碳微球(Au@CMSs)的制备及水环境中汞离子在该材料上的电化学行为. 实验结果表明,在0.1mol•L^-1 pH = 5.0的NaAc-HAc缓冲溶液中,采用方波伏安法测定汞离子,其浓度与氧化峰电流强度线性良好,相关系数为0.997,检出限为3.69 × 10^-8 mol•L^-1（3σ方法）.     

Anodic generation of cerium (IV) at glassy carbon in acetic acid and coulometric titrations with the generated reagent

Conditions for electrochemical generation of cerium(IV) at glassy carbon in acetic acid in the presence of alkali-metal acetates and sodium perchlorate, respectively, were investigated. A high current efficiency was achieved in anodic oxidation of cerium(III) in acetate supporting electrolytes. Coulometric titration methods for the determination of reducing substances with the generated oxidant were also developed. The end-points were determined by the biamperometric and bipotentiometric methods. The error of the determinations was less than + 2%.     

Coulometric generation of H(+) and D(+) ions in aqueous media by anodic oxidation of hydrogen and deuterium dissolved in palladium

Coulometric generation of H(+) and D(+) ions in aqueous media by the oxidation of hydrogen and deuterium dissolved in palladium, is described. Hydrogen and deuterium dissolved in palladium were found to be oxidized at more negative potentials than the oxidation potentials of water and other components present. The H(+) and D(+) ions generated were used for the titration of tris(hydroxymethyl) aminomethane, piperidine, triethylamine and sodium tetraborate, the end-point being determined potentiometrically with a glass electrode and an SCE. In titrations of 0.001-0.1M solutions of the bases, the current efficiency was 100%.     

Binding of Copper(II), Cobalt(II), and Nickel(II) Cations with Humic Acids and Their Sodium Salts in Aqueous Media

Binding of Cu(II), Co(II) and Ni(II) cations to humic acids and their sodium salts was studied in aqueous media at pH 3-6 by spectrophotometry and potentiometric titration technique.     

Speciation of manganese in fresh water-I Use of EPR studies

The process of standardization of the use of electron paramagnetic resonance (EPR) spectrometry in the determination of Mn(II) species in aqueous solution by comparison with atomic absorption spectrometry (AAS) is discussed. It is shown that EPR signals obtained from standardized aqueous solutions of manganese(II) perchlorate and nitrate in the concentration range of 0.05-2 mg/l. do not vary significantly over the pH range 2.1-7.0. Study of the effect (on the manganese EPR signals) of the addition of inorganic ions commonly found in significant concentrations in natural waters, viz. chloride, sulphate and bicarbonate, has shown that such ions, at the levels reported to occur in surface fresh waters, will not complex manganese(II); however, evidence is obtained that humic acid/manganese complexes could be present in such waters. The EPR signals are not affected by ionic strengths of the levels found in fresh waters.     

Electrochemical generation of manganese(III) and behaviour of the generated oxidant in acetic acid in the presence of perchlorate ions

Summary Research was carried out to determine conditions for the anodic generation of manganese(III) with high current efficiency in solutions of sodium perchlorate in acetic acid, and to examine the behaviour of the oxidant thus generated. The effects of water and acetic anhydride on current efficiency in the generation of the oxidant was also examined. The formal redox potential of the Mn(III)/ Mn(II) system is decreased with increasing concentrations of sodium acetate in the solution. The effect of sodium perchlorate and perchloric acid concentrations is the reverse. Procedures for coulometric titrations of a number of substances with the generated oxidant were developed, end point being detected using biamperometric and potentiometric methods. Perchloric acid accelerates the oxidation of certain substances with manganese(III) in acetic acid and increases the sensitivity of end-point detection using the potentiometric method.

---

Elektrochemische Erzeugung von Mangan(III) und das Verhalten dieses Oxydationsmittels in Essigsäure bei Gegenwart von Perchlorat

Zusammenfassung Die Bedingungen der anodischen Erzeugung von Mangan(III) mit hoher Stromausbeute in Essigsäure, nach Zugabe von Natriumperchlorat wurden untersucht; das elektrochemische Verhalten des so dargestellten Oxydationsmittels wurde ebenfalls untersucht. Der Einfluß von Wasser und Essigsäureanhydrid auf die prozentuelle Stromausbeute des erwähnten Oxydationsmittels wurde verfolgt. Das Formalredoxpotential des Systems Mn(III)/ Mn(II) sinkt bei Erhöhung der Konzentration an Natriumacetat in der Lösung. Perchlorsäure wie auch Natriumperchlorat üben eine entgegengesetzte Wirkung aus und führen zur Steigerung des Formalredoxpotentials bei Erhöhung ihrer Konzentration. Verfahren zur coulometrischen Titration verschiedener Substanzen mittels biamperometrischer oder potentiometrischer Erfassung des Titrationsendpunktes wurden ausgearbeitet. In Gegenwart von Perchlorsäure wächst die Geschwindigkeit der Oxydation einiger Substanzen in Essigsäure in Gegenwart von Mn(III) und auch die Empfindlichkeit der Endpunktbestimmung verbessert sich.

---

---

Presented at the 9th International Symposium on Microchemical Techniques, Amsterdam, August 28–September 2, 1983.     

Application of potentiometric stripping analysis to compleximetric titrations

Samples that are 0.1–10 mM in lead(II) or 0.025–0.25 mM in bismuth(III) can be titrated with EDTA and the titrations monitored by means of computerized potentiometric stripping analysis. The coefficients of variation are 0.12–0.40%; systematic errors are estimated from computer-calculated titration curves using conditional constants obtained from the titration curves. The conditional stability constants for calcium(II), manganese(II) and lanthanum(II) in 0.5 M sodium chloride are determined from the exchange reaction with the lead—EDTA complex.     

Indirect spectrophotometric determination of chloride by solvent extraction as tris(1,10-phenanthroline)iron(II) thiocyanate

An indirect spectrophotometric method for the determination of small amounts of chloride in fresh waters is described. Chloride ions react with mercury(II) thiocyanate to liberate thiocyanate ions, which can be selectively extracted into nitrobenzene with tris(1,10-phenanthroline)iron(II) chelate cations. The red color (516 nm) of the organic phase measured against a reagent blank is proportional to the initial concentration of chloride ions in the aqueous phase. At least an equimolar amount of tris(1,10-phenanthroline)iron(II) chelate and a 3-fold amount of mercury(II) thiocyanate are needed; the optimal pH range is 1.5–3.5. Beer's law is obeyed over the concentration range of 0.8–5.6 10^-5 M of chloride. The color stability and the apparent sensitivity are better than those of the mercury(II) thiocyanate-iron(III) method. Large amounts of sulphate, phosphate, fluoride, carbonate, acetate, potassium, sodium, and ammonium ions had negligible or no effect ; bromide, iodide, cyanide, sulphide, and thiocyanate interfere.     

A examination of the EDTA titration of manganese(II) taking into consideration formation of 1:1 and 1:2 complexes with Eriochrome Black T indicator

In the EDTA titration of manganese(II) with Eriochrome Black T as indicator, the effect of formation of 1:1 and 1:2 manganese(II)—indicator complexes must be taken into consideration. The titration error can be reduced to less than 0.1%. For comparison purpose the titration of zinc(II) has also been studied.     

Investigation of manganese(III) fluoride for coulometric titration

A study has been made of the use of electrogenerated manganese(III), in an electrolyte containing fluoride, for coulometric titration. The addition of fluoride prevented the deposition of manganese dioxide on the anode, and was responsible for increase of the current efficiency and for extension of the feasible range of current density, owing to complex formation between manganese(III) and fluoride. The bonding ratio, the apparent stability constant and the redox potential of the complex were also estimated from the Nernst equation and the current-potential curves.     

Square-wave adsorptive stripping voltammetry at glassy carbon electrode for selective determination of manganese. Application to some industrial samples

A new method to determine manganese by voltammetry after controlled adsorptive accumulation of the manganese–ammonium–acetate at the glassy carbon electrode is described. The manganese complex gives well-defined voltammetric peak at pH 4.0 and 9.0. Cathodic stripping voltammetry combined with the Osteryoung square-wave mode at the glassy carbon electrode gave rise to both sensitivity and selectivity of the determination of manganese in some industrial samples. The method offers enhanced sensitivity in comparison to analogous measurements presented in the literature. The detection limit with 5 min accumulation is 0.022 μg l⁻¹ . Simultaneous determination of manganese in presence of Cu(II), Pb(II) and Zn(II) could be easily done using anodic stripping voltammetry at pH 4.0. Calibration plots are constructed and the method was checked with the aid of standard industrial reference samples giving values of standard deviations between 1.2 and 1.8.     

电位滴定测定富锂锰基正极材料中锰

采用盐酸、硝酸溶解样品,加入焦磷酸钠溶液并调节溶液pH为6.0~7.0。用高锰酸钾标准溶液滴定至电位滴定仪上,根据消耗的高锰酸钾标准溶液的体积计算样品中的锰含量。探究了焦磷酸钠用量、溶液pH、共存元素等对测定锰含量的影响。在最优的实验条件下,方法的相对标准偏差在0.13%~0.22%之间,加标回收率在99.8%~100.5%之间。本方法是富锂锰基正极材料中质量分数10%~60%的锰测定的理想方法。     

The second and third order non-linear optical properties of liquid crystalline polymers

The second and third order non-linear optical susceptibilities of several donoracceptor substituted side chain polymers, some of which exhibit mesophases, will be reported. The susceptibilities were measured by harmonic generation from thin films, typically 0·5 μm thick, at a fundamental wavelength of 1064 nm and 1579 nm. For second harmonic generation, the spin coated films were contact poled on a glass substrate with an interdigited electrode pattern. Typical values obtained were χ⁽²⁾₃₁ = 1 × 10^-9 esu and χ⁽²⁾₃₃ = 3 × 10^-9 esu, the largest value was χ⁽²⁾₃₃ = 6·3 × 10^-9 esu. The difficulty in deriving reliable second order structure-property relations because of the large effect which the contact poling process has on the non-linear optical susceptibility of the films will be highlighted. The highest χ⁽³⁾ value of 5·8 × 10^-12 esu obtained from an amorphous film of a polymer with an asymmetrically substituted azo side group is comparable with the susceptibility of more typical third order non-linear materials such as the main chain polymers polyphenylacetylene and poly-p-phenylenebenzobisthiazole.     

Synthesis, characterization, and solution properties of a novel cross-bridged cyclam manganese(IV) complex having two terminal hydroxo ligands

A novel monomeric tetravalent manganese complex with the cross-bridged cyclam ligand 4,11-dimethyl-1,4,8,11-tetraazabicyclo[6.6.2]hexadecane (Me2EBC), [Mn(IV)(Me2EBC)(OH)2](PF6)2, was synthesized by oxidation of Mn(II)(Me2EBC)Cl2 with H2O2 in the presence of NH4PF6)in aqueous solution. The X-ray crystal structure determination of this manganese(IV) compound revealed that it contains two rare terminal hydroxo ligands. EPR studies in dry acetonitrile at 77 K show two broad resonances at g = 1.96 and 3.41, indicating that the manganese(IV) exists as a high-spin d3 species. Resonance Raman (rR) spectra of this manganese(IV) species reveal that the dihydroxy moiety, Mn(IV)(OH)2, is also the dominant species in aqueous solution (pH < 7). pH titration provides two pK(a) values, 6.86(4) and 10.0(1), associated with stepwise removal of the last two oxygen-bound protons from [Mn(IV)(Me2EBC)(OH)2](2+). The cyclic voltammetry of this manganese(IV) complex in dry acetonitrile at 298 K demonstrates two reversible redox processes at +0.756 and -0.696 V (versus SHE) for the Mn4+/Mn3+ and Mn3+/Mn2+ couples, respectively. This manganese(IV) complex is relatively stable in weak acidic aqueous solution but easily degrades in basic solution to manganese(III) derivatives with an 88 +/- 1% yield.     

The effect of platinum(IV) on the coulometric generation of tin(II)

The current efficiency of tin(II) generation has been measured for various electrolytes and electrodes. The best results (>99.9%) were obtained with the paraffin-impregnated graphite electrode in 2M CaCl(2) + 0.2M HCl + 0.2M SnCl(4). In titrations of platinum(IV) with electrogenerated tin(II) in an electrolyte containing chloride or bromide it was found that the presence of platinum(II) or (IV) interferes in the cathodic generation of tin(II). The platinum is reduced to the elemental state at the electrode and causes simultaneous generation of hydrogen which decreases the current efficiency. This effect is more pronounced in chloride media.     

Electroreduction and determination of Pipril (Piperacillin) in both aqueous and biological samples

The electrochemical behavior of the relatively new antibacterial antibiotic Pipril (Piperacillin) at the dropping mercury electrode is investigated using both direct current polarography (DCP) and differential pulse polarography (DPP). At the hanging mercury electrode (HMDE), the reduction mechanism has been elucidated using cyclic voltammetric technique in the pH range from 2 to 10. The effect of some metal ions, e.g. Cu(II) and Pb(II) has been also tested. Determination of the drug using adsorptive stripping analysis was assessed in both aqueous and urine samples. The effect of the different experimental parameters affecting the drug determination, e.g. pH, supporting electrolyte nature, accumulation potential, accumulation time and other operational parameters are also mentioned. Detection limits of 5 × 10⁻⁹ and 1 × 10⁻⁸M Pipril in aqueous and urine samples, respectively, are achieved.     

Hydrolytic cleavage of DNA by quercetin manganese(II) complexes

Quercetin manganese(II) complexes were investigated focusing on its DNA hydrolytic activity. The complexes successfully promote the cleavage of plasmid DNA, producing single and double DNA strand breaks. The amount of conversion of supercoiled form (SC) of plasmid DNA to the nicked circular form (NC) depends on the concentration of the complex as well as the duration of incubation of the complexes with DNA. The maximum rate of conversion of the supercoiled form to the nicked circular form at pH 7.2 in the presence of 100 μM of the complexes is found to be 1.32 × 10⁻⁴ s⁻¹. The hydrolytic cleavage of DNA by the complexes was supported by the evidence from free radical quenching, thiobarbituric acid-reactive substances (TBARS) assay and T4 ligase ligation.