超声相控阵距离幅度曲线计算方法

超声相控阵偏转聚焦声场能量分布不均匀,造成不同位置的缺陷回波幅度差异,针对该缺陷量化问题,提出超声相控阵系统距离幅度曲线理论计算方法.在非近轴近似声场模型的基础上,结合缺陷散射模型来建立相控阵系统测量模型,再利用该方法来预测不同位置横通孔缺陷的回波信号,进而获得信号幅度随位置的变化曲线.分析对比了不同偏转聚焦声束理论计...     

多层介质中超声相控阵声场仿真*

由于良好的声束偏转与聚焦特性,超声相控阵已经广泛应用于多层固体介质的缺陷检测。当超声束经过多层介质时,由于反射、透射以及模式转换的存在,多种声束存在于这种结构中,使得声场分析变得复杂。为了提高多层介质检测的准确性,有必要对超声声场的分布规律进行深入地了解。该文结合高斯声束等效点源模型以及射线追踪法,给出了相控阵声源在多层固体介质中激发声场的仿真方法,并且模拟计算了一维线型相控阵在楔块-铝-黄铜-钢四层固体介质中的辐射声场。通过对不同延时法则的计算,实现了声波在这种复杂介质中的偏转与聚焦,进而研究了不同焦点处聚焦声场的分布。结果表明:相控阵方法能使聚焦点处的声场幅值增大,能量集中,提高了检测分辨率;不同聚焦点处声场聚焦效果不同,实际检测时应根据检测区域结构及位置特点,合理放置相控阵换能器。与瑞利积分法的比较表明,该文的仿真方法适用于多层介质相控阵声场的计算。     

Nonparaxial multi-Gaussian beam models and measurement models for phased array transducers

A nonparaxial multi-Gaussian beam model is proposed in order to overcome the limitation that paraxial Gaussian beam models lose accuracy in simulating the beam steering behavior of phased array transducers. Using this nonparaxial multi-Gaussian beam model, the focusing and steering sound fields generated by an ultrasonic linear phased array transducer are calculated and compared with the corresponding results obtained by paraxial multi-Gaussian beam model and more exact Rayleigh-Sommerfeld integral model. In addition, with help of this novel nonparaxial method, an ultrasonic measurement model is provided to investigate the sensitivity of linear phased array transducers versus steering angles. Also the comparisons of model predictions with experimental results are presented to certify the accuracy of this provided measurement model.     

圆柱类构件超声相控阵聚焦模型

在利用平面相控阵超声换能器对圆柱类构件检测时,受曲界面结构引起的入射波和回波时延的影响,扫描声束的波阵面产生弯曲,在利用传统迭代遍历算法计算延迟时间时效率低,无法发挥相控阵换能器检测优势。针对上述问题,建立了一种基于圆柱类构件特征和耦合介质特性的超声相控阵扫描成像的聚焦模型。该模型基于换能器、耦合介质、圆柱类构件材料特性和几何关系以及声线模型和折射定律,建立了耦合介质及被检构件的声速、曲面曲率半径、阵列与曲面间的距离等关联的延迟时间聚焦控制模型。利用该模型计算出的延时时间,对各阵元发射时间进行控制,从而实现扫描声束的聚焦。该文以液体和有机玻璃制介质楔块为例,对圆柱钢曲面的相控阵声束聚焦进行了仿真实验,结果表明该文方法计算效率显著提升,同时声束可以在预设位置实现聚焦,验证了该模型在计算效率上的优势与有效性。     

多层奥氏体钢中超声相控阵辐射声场分析

针对一维线性超声相控阵透过楔块,在多层不同晶轴取向的奥氏体钢中的声场辐射问题,结合高斯声束等效点源模型以及基于时间最小原理的射线追踪法,给出了各层介质中透射声场的计算方法。将奥氏体钢近似为横向各向同性介质,计算了相控阵透过楔块,在晶轴取向为0°的奥氏体钢中的无延时纵波声场,计算结果与COMSOL仿真结果相吻合,从而验证了所用方法的正确性。通过加入不同的延迟法则,仿真计算了三层含有不同晶轴取向(0°,30°,100°)的奥氏体钢中的纵波声场,实现了相控阵声场的偏转与聚焦,分析了偏转声场与聚焦声场的传播特性。仿真结果表明,不同的晶轴取向将导致不同的声束偏转以及聚焦效果。通过延迟激励各阵元,虽然可以控制声束偏转或聚焦到预定位置,但是晶轴取向仍会对声束宽度以及幅值产生一定的影响。      

双层界面下非近轴近似多元高斯模型的相控阵声场模拟

非近轴近似多元高斯模型克服了近轴近似条件的限制,能保证较大偏转角度下模拟声场的精确度和效率。根据双层介质的瑞利积分模型和单层介质的非近轴近似多元高斯模型,推导出双层介质中基于非近轴近似多元高斯模型的单阵元辐射声场计算模型。并在得到各阵元声束偏转聚焦的延迟时间基础上,累加得到基于非近轴近似高斯模型的超声相控阵横波检测辐射声场计算模型。模拟计算带丙烯酸树脂楔块的超声相控阵探头在钢中横波检测的声束偏转与偏转聚焦辐射声场,并与近轴近似多元高斯模型的横波检测声束的偏转聚焦辐射声场进行比较分析。对比分析结果表明非近轴近似多元高斯模型计算速度更快,用时约为近轴近似多元高斯模型的1/13。此外,非近轴近似高斯模型方法横波检测的聚焦声束覆盖区域更大,能量更集中,更适于远场区域检测。      

瞬态波位移场计算方法在相控阵声场模拟中的实验验证

通过实验研究了声束偏转不同角度和声场半径变化时线性相控阵的声场特性,并与基于瞬态波位移解析解的相控阵声场计算方法得到的理论结果进行了对比。首先研究了基于半圆圆弧离面瞬态位移的声场计算方法,并进行了数值计算可靠性的优化。然后建立了一套相控阵瞬态波位移场的测量系统,以半圆形钢板为试件,纵波传感器为接收传感器,测量了偏转角度为-10°,-30°,-50°,-70°,及声场半径为50 mm,75 mm,100 mm和125 mm时线性超声相控阵的声束指向性;同时以基于瞬态波位移解析解的相控阵声场计算方法,计算了相同条件下该相控阵的声束指向性。最后将实验结果与理论结果进行了对比,取得了较好的一致。说明基于瞬态波位移的相控阵声场计算方法可以较好地计算线阵的声场,对于声束偏转较大角度和声场半径变化时也同样有效。      

相控阵超声接收动态聚焦算法及其物理实现

本文提出一种新的相控阵接收动态聚焦的实现方案,在传统的单接收聚焦点接收的基础上,把各换能器单元接收信号的补偿位置计算出来,在各通道数据叠加前将数据动态补偿,实现各个采样点都接收动态聚焦。在工程上,实际检测深度有一定范围限制,补偿点数其实并不是太大,所以方法具有可实现的条件。并且在计算补偿点时,可以使用楔块折射后的声波传播路径,使在折射的条件下也可成功动态聚焦。本文提供了计算补偿点的方法,最后给出了计算机仿真对比和物理实现方案,仿真结果可以看出成像效果与传统单点聚焦相控阵对比有了显著提高。提出的动态聚焦的方法很大地改善了成像质量,方法具有实用价值。     

相控阵天线主控系统中实时数据交互

波束控制系统是高功率相控阵天线的神经中枢,负责天线阵面中所有单元相位的精确控制和状态监测任务。为实现天线阵面的快速、精确波束转换,采用分布式拓扑结构和嵌入式实时操作系统,设计了两级分布式波束控制方案,开发了基于VxWorks的相控阵天线主控系统。通过UDP协议实现主控系统与其他系统的多节点网络通讯;针对高速、实时通讯需求,利用VxWorks多任务编程接口,设计了一种基于双缓冲队列的Socket通讯方法;为使通讯被各方正确解析,制定了自定义的应用层协议。基于VxWorks的相控阵天线主控系统的开发应用,验证了方案的可行性以及控制软件的可靠性和稳定性。     

大气湍流对多抖动法相干合成技术中相位调制信号的影响

分析了大气湍流对采用多抖动法实现的相干合成阵列光束中相位调制信号的影响. 文章首先根据广义惠更斯-菲涅耳原理,采用折射率结构函数对大气湍流进行描述,推导了多抖动法相干合成中阵列光束通过大气湍流后相位调制信号的一般表达式. 在此基础上进行数值模拟,分析了传输距离、湍流强度、光束阵列占空比和光斑尺寸等因素对相位调制信号的影响. 研究发现随着传输距离的增大,相位调制信号强度会先增大后减小,存在一个极大值点;随着湍流强度的增强,相位调制信号强度极大值点的出现距离不断缩短;当光束阵列占空比一定时,随着光斑尺寸的增大 关键词： 大气湍流 相干合成 多抖动法 相位调制     

Calculation of radiation acoustical fields from phased arrays with nonparaxial multi-Gaussian beam model

A nonparaxial multi-Gaussian beam model based on the rectangular aperture is proposed in order to overcome the limitation of paraxial Gaussian beam model which losing accuracy in off-axis beam fields. With the method, acoustical field generated by an ultrasonic linear phased array transducer is calculated and compared with the corresponding field obtained by Rayleigh-Sommerfeld integral, paraxial multi-Gaussian beam model, and Fraunhoffer approximation method. Simulation examples show that nonparaxial multi-Gaussian beam model is not limited by the paraxial approximation condition and can predict efficiently and accurately the acoustical field radiated by a linear phased array transducer over a wide range of steering angles.     

基于幅度调制的非线性超声相控阵成像方法*

超声相控阵是超声检测领域常用的材料缺陷定位和成像技术,可便捷快速地对裂纹、孔洞等缺陷进行成像。但是,传统超声相控阵方法对较小缺陷如闭合裂纹不太敏感。非线性超声信号因对材料性能退化以及微小缺陷敏感而广受关注。本文针对疲劳闭合裂纹检测,提出一种基于幅度调制的非线性超声相控阵成像方法,通过测量物理聚焦和虚拟聚焦两种聚焦模式下超声扩散场中的声能差,并将其作为非线性参量,实现疲劳裂纹闭合部分的定位成像和定量表征。将该法应用于7075铝合金试样疲劳裂纹的实验测量,并研究了扩散场信号延迟时间对非线性超声相控阵成像结果的影响。结果表明：相较于传统超声相控阵全聚焦法,基于幅度调制的非线性超声相控阵成像方法能够更准确地定位和成像疲劳裂纹闭合部分;延迟时间的选择对疲劳裂纹长度的表征精度影响较大,本文研究了该延迟时间的选择方法并实现了检测结果的优化。     

固体中线性相控阵列的瞬态聚焦特性

针对线性相控阵列在固体介质中的声场聚焦特性及参数优化问题,该文给出了一个线性阵列的纵波瞬态聚焦声场模型.数值结果表明,当阵元被短时脉冲信号激励时,瞬态聚焦声场中不会形成栅瓣,突破了传统稳态理论模型中对阵元间距的限制;同时由于横纵波在聚焦区域内可完全分离,声束旁瓣的幅值也得到了抑制.其次,增大阵元间距能够显著提高聚焦性能...     

基于超声相控阵的环焊缝缺陷检测方法研究

针对传统超声探头焦距固定,检测位置的改变就要更换相应焦距的探头而影响检测效率的问题,提出一种基于超声相控阵换能器的环焊缝缺陷检测方法。而超声相控阵具有电子偏转和电子聚焦特性,能在不移动的情况下发射偏转聚焦超声束,有效地解决了上述问题。首先基于超声相控线阵换能器的声场特点,采用数值分析方法,研究了影响声束偏转聚焦性能的几个主要参数。然后给出了与超声相控阵换能器相连接的多通道数据采集系统结构。介绍了单通道声信号的硬件结构及相应的信号处理方法,实现了对换能器中单个阵元的精确延时的控制。实验结果表明,优化设计的超声相控线阵换能器具有较高的检测精度和检测效率。     

Oblique incidence effect on steering efficiency of liquid crystal polarization gratings used for optical phased array beam steering amplification

A liquid crystal polarization grating (LCPG) is proposed that amplifies the steering angle of a liquid crystal optical phased array for non-mechanical beam steering, taking advantage of its high steering efficiency under normal incidence. However, oblique incidence may play an important role in the overall steering efficiency. The effect of oblique incidence on steering efficiency of a LCPG was analyzed by numerically solving the extended Jones matrix and considering propagation crosstalk. The results indicate that the outgoing laser beam is amplitude-modulated under the effect of oblique incidence and behaves as a sinusoidal-modulated amplitude grating, which diffracts certain energies to non-blazed orders. Over-oblique incidence may even eliminate the steering effect of the incident beam. The modulation depth of the induced amplitude grating was found to be proportional to the product of sinusoidal value of oblique incidence angle and the LC layer thickness, and inversely proportional to the periodic pitch length of the LCPG. Both in-plane incidence and out-of-plane incidence behave similarly to influence the steering efficiency. Finally, the overall steering efficiency for cascaded LCPGs was analyzed and a difference of up to 11 % steering efficiency can be induced between different LCPG configurations, even without considering the over-oblique incidence effect. Both the modulation depth and final steering efficiency can be optimized by varying the LC birefringence and layer thickness.     

各向异性焊缝中超声相控阵瞬态声场仿真及缺陷定位方法

针对多层各向异性奥氏体不锈钢焊缝中超声相控阵瞬态声场的仿真问题,提出应用高斯声束等效点源模型计算宽带离散化的多个单频稳态声场,通过傅里叶变换将其拓展为瞬态声场,并分析了声场转换过程的主要影响参数.该方法可快速计算焊缝内部超声相控阵聚焦声场的瞬态能量分布和任意一点的时域波形信号.在此基础上针对多层奥氏体不锈钢焊缝内部缺陷...     

Modeling of Focused Acoustic Field of a Concave Multi-annular Phased Array Using Spheroidal Beam Equation

A theoretical model of focused acoustic field for a multi-annular phased array on concave spherical surface is proposed.In this model,the source boundary conditions of the spheroidal beam equation(SBE) for multi-annular phased elements are studied.Acoustic field calculated by the dynamic focusing model of SBE is compared with numerical results of the O'Neil and Khokhlov-Zabolotskaya-Kuznetsov(KZK) model,respectively.Axial dynamic focusing and the harmonic effects are presented.The results demonstrate that the dynamic focusing model of SBE is good valid for a concave multi-annular phased array with a large aperture angle in the linear or nonlinear field.     

Development of phased array techniques to improve characterization of defect located in a component of complex geometry

Ultrasonic inspection of complex geometry components has to cope with different problems: limited access of the area assumed to be insonified, beam misorientation and distortions, loss of sensitivity. Those harmful effects can lead to inspection performance degradations, especially in terms of defect detection and characterization. Phased array techniques may be used to overcome such difficulties, as they can provide an optimal mastering of the ultrasonic beam radiated through the inspected component. This paper presents some applications of phased array inspections carried out by the French Atomic Energy Commission (CEA) and the French Company of Electricity (EDF) in the framework of R&D studies. Inspections of components with varying profile (of planar and cylindrical parts, misalignment and local depression), and containing artificial reflectors have been carried out with pulse echo immersion techniques, using standard and phased arrays transducers. Optimal delay laws have been applied to preserve the beam characteristics in spite of the varying profile geometry encountered as the phased array transducer was moved over the component. Those delay laws allow to efficiently compensate the beam distortions generated by the profile geometry. They were computed using a specific model and compared to experimental delays obtained using through transmission tests. Experimental and simulation results showed that the defect detection and characterization performances were greatly enhanced using phased array techniques. In the presented examples, with standard transducers, defects located below the irregular parts of the specimen were partially detected, in accurately located or even missed, whereas phased array inspections enabled to detect and locate all of these defects.     

Ultrasonic beam focusing characteristics of shear-vertical waves for contact-type linear phased array in solid

We investigate the beam focusing technology of shear-vertical(SV) waves for a contact-type linear phased array to overcome the shortcomings of conventional wedge transducer arrays. The numerical simulation reveals the transient excitation and propagation characteristics of SV waves. It is found that the element size plays an important role in determining the transient radiation directivity of SV waves. The transient beam focusing characteristics of SV waves for various array parameters are deeply studied. It is particularly interesting to see that smaller element width will provide the focused beam of SV waves with higher quality, while larger element width may result in erratic fluctuation of focusing energy around the focal point. There exists a specific range of inter-element spacing for optimum focusing performance. Moreover, good beam focusing performance of SV waves can be achieved only at high steering angles.     

Feasibility of a phased acoustic array for monitoring acoustic signatures from meshing gear teeth

This paper investigates the feasibility of sensing damage emanating from rotating drivetrain elements such as bearings, gear teeth, and drive shafts via airborne paths. A planar phased acoustic array is evaluated as a potential fault detection scheme for detecting spatially filtered acoustic signatures radiating from gearbox components. Specifically, the use of beam focusing and steering to monitor individual tooth mesh dynamics is analyzed taking into consideration the constraints of the array/gearbox geometry and the spectral content of typical gear noise. Experimental results for a linear array are presented to illustrate the concepts of adaptive beam steering and spatial acoustic filtering. This feasibility study indicates that the planar array can be used to track the acoustic signatures at higher harmonics of the gear mesh frequency.