Shock wave diffraction in the presence of a supersonic co-flow jet

The interaction between a diffracting shock wave and a uniform jet is a case that so far has only been partially investigated. This interaction is extremely important for the control of noise generation and improvement of combustor performance. To fill this knowledge gap, three geometries of the diffracting corner, namely a straight ramp, a serrated ramp, and a rounded corner, have been tested experimentally to study the interaction of shock diffraction with a supersonic co-flow jet at incident Mach numbers of 1.31 and 1.59, with Reynolds numbers of \(1.08\times 10^{6}\) and \(1.68\times 10^{6}\), respectively. Schlieren photography was employed to analyse the evolution of the flow phenomena. The aim is to provide a qualitative understanding of the interaction between the diffracting shock wave and the uniform jet relevant to future high-speed transport. The results show that the flow field evolves more rapidly and develops stronger structures for a higher shock Mach number. The diffraction around a rounded splitter develops a periodical vortical structure which continues after the disturbance introduced by the passage of the shock wave is removed.     

Experimental study of the shock–bubble interaction with reshock

The interaction of a planar shock wave with a spherical density inhomogeneity is studied experimentally under reshock conditions. Reshock occurs when the incident shock wave, which has already accelerated the spherical bubble, reflects off the tube end wall and reaccelerates the inhomogeneity for a second time. These experiments are performed at the Wisconsin Shock Tube Laboratory, in a 9m-long vertical shock tube with a large square cross section (25.4×25.4 cm²). The bubble is prepared on a pneumatically retracted injector and released into a state of free fall. Planar diagnostic methods are used to study the bubble morphology after reshock. Data are presented for experiments involving two Atwood numbers (A = 0.17 and 0.68) and three Mach numbers (1.35 < M < 2.33). For the low Atwood number case, a secondary vortex ring appears immediately after reshock which is not observed for the larger Atwood number. The post-reshock vortex velocity is shown to be proportional to the incident Mach number, M, the initial Atwood number, A, and the incident shock wave speed, W _i.     

激波冲击SF6重气泡引发射流的数值模拟

为深入研究重气泡内激波聚焦和射流生成的机理,采用高精度计算格式和高网格分辨率对马赫数为1.23的平面入射激波与SF₆重气泡的作用过程进行数值模拟,计算结果与文献中实验吻合较好。结果显示:入射激波在重气泡内首先在流向上汇聚形成上、下对称的高压区,随后,这对高压区在SF₆重气泡中心对称轴处再次碰撞,完成激波聚焦过程,并在气泡下游界面附近形成远大于初始压力和密度的局部高压高密度区,体现出SF₆重气泡极强的聚能效应;激波聚焦还引起气泡下游界面附近的涡量变化,涡对的旋转能够加速射流形成与发展。因此,SF₆重气泡下游界面附近的高压区和涡量分布对形成射流结构均有促进作用。     

Nonlinear Strong Shock Interactions: A Shock-Fitted Approach

This paper addresses nonlinear effects which result from the interaction of shock waves with vortices. A series of experiments are carried out, which involve the interaction of a strong shock wave with a single plane vorticity wave and a randomly distributed wave system. These experiments are first conducted in the linear regime to obtain a mutual verification of theory and computation. They are subsequently extended into the nonlinear regime. A systematic study of the interaction of a plane shock wave and a single vortex is then conducted. Specifically, we investigate the conditions under which nonlinear effects become important, both as a function of shock Mach number, M ₁, and incident vortex strength (characterized by its circulation Γ). The shock Mach number is varied from 2 to 8, while the circulation of the vortex is varied from infinitesimally small values (linear theory) to unity. Budgets of vorticity, dilatation, and pressure are obtained. They indicate that nonlinear effects become more significant as both the shock Mach number and the circulation increase. For Mach numbers equal to 5 and above, the dilatation in the vortex core grows quadratically with circulation. An acoustic wave propagates radially outward from the vortex center. As circulation increases, its upstream-facing front steepens at low Mach numbers, and its downstream-facing front steepens at high Mach numbers. A high Mach number asymptotic expansion of the Rankine--Hugoniot conditions reveals that nonlinear effects dominate both the shock motion and the downstream flow for ΓM ₁ > 1. Received 28 June 1997 and accepted 25 November 1997     

Numerical investigation of toroidal shock wave focusing in a cylindrical chamber

In this paper, focusing of a toroidal shock wave propagating from an annular shock tube into a cylindrical chamber was investigated numerically with the dispersion controlled dissipation (DCD) scheme. The first case for an incident Mach number of 1.5 was conducted and compared with experiments for validation. Then, several cases were calculated for higher incident Mach numbers varying from 2.0 to 5.0, and complicated flow structures were observed. The numerical study was mainly focused on two aspects: focusing process and flow structures. The process, including diffraction, focusing, and reflection, is displayed to reveal the focusing mechanism, and the flow structures at different incident. Mach numbers are used to demonstrate shock reflection styles and focusing characteristics. PACS 47.40.Ki; 47.40.Nm; 52.35.Tc     

The interaction of a shock wave with the boundary layer in a reflected shock tunnel

The influence of a nontotal reflection on the interaction of a reflected shock wave with the boundary layer in a reflected shock tunnel has been investigated. The calculating method of the velocity, the temperature and the Mach number profiles in the boundary layer in reflected shock fixed coordinates has been obtained. To account for equilibrium real gas effects of nitrogen, the numerical results show that the minimum Mach number in the boundary layer has been moved from the wall into the boundary layer with the increasing of the incident shock Mach number. The minimum Mach number, the shock angle in the bifurcated foot and the jet velocity along the wall to the end plate are reduced owing to the increasing of the area of nozzle throat. The numerical results are in good agreement with measurements.     

柱形汇聚激波冲击球形重气体界面的实验研究

采用高速纹影法实验研究了柱形汇聚激波与球形重气体界面相互作用的 Richtmyer-Meshkov不稳定性问题. 激波管实验段基于激波动力学理论设计, 将马赫数为1.2 的平面激波转化为柱形汇聚激波, 气体界面由肥皂膜分隔六氟化硫(内)和空气(外)得到. 采用高速摄影机在单次实验中拍摄激波运动的全过程, 对柱形激波的形成进行了实验验证, 并进一步观测了汇聚激波与球形气体界面相互作用过程中的波系发展和气体界面变形以及反射激波同已变形界面二次作用的流场演化. 结果表明: 当柱形汇聚激波穿过气泡界面以后, 气泡左侧界面极点沿激波传播方向保持匀速运动, 气泡右侧界面发展成为射流结构, 气泡主体发展成为涡环结构; 在反射激波的二次作用下, 流场中无序运动显著增强并很快进入湍流混合阶段.     

Shock wave deformation in shock-vortex interactions

An initially planar shock wave can undergo significant distortion to its shape along with changes in its strength during the period of its interaction with a compressible vortex. This phenomenon is studied by numerically simulating the shock wave-vortex interaction with a high resolution shock-capturing scheme. Incident shock waves of various Mach numbers are made to interact with a compressible vortex and the dependence of the shock wave distortion on the strength of the incident shock wave is studied in detail. It is known that the type of complex shock structure formed in the later stages of a compressible vortex-shock wave interaction is dependent on the Mach number of the incident shock wave. A simple physical model based on the principle of shock wave reflection is proposed to explain this complex shock structure formation and its dependence on the relative strengths of the interacting vortex and shock wave. Received July 28, 1997 / Accepted November 17, 1997     

Effect of air jet vortex generators on a shock wave boundary layer interaction

The effect of upstream injection by means of continuous air jet vortex generators (AJVGs) on a shock wave turbulent boundary layer interaction is experimentally investigated. The baseline interaction is of the impinging type, with a flow deflection angle of 9.5° and a Mach number M _e  = 2.3. Considered are the effects of the AJVGs on the upstream boundary layer flow topology and on the spatial and dynamical characteristics of the interaction. To this aim, Stereoscopic Particle Image Velocimetry has been employed, in addition to hot-wire anemometry (HWA) for the investigation of the unsteady characteristics of the reflected shock. The AJVGs cause a reduction of the separation bubble length and height. In addition, the energetic frequency range of the reflected shock is increased by approximately 50%, which is in qualitative agreement with the smaller separation bubble size.     

Effect of incident shock wave strength on the decay of Richtmyer–Meshkov instability-introduced perturbations in the refracted shock wave

The effect of incident shock wave strength on the decay of interface introduced perturbations in the refracted shock wave was studied by performing 20 different simulations with varying incident shock wave Mach numbers (M ~ 1.1? 3.5). The analysis showed that the amplitude decay can be represented as a power law model shown in Eq.7, where A is the average amplitude of perturbations (cm), B is the base constant (cm^?(E?1), S is the distance travelled by the refracted shockwave (cm), and E is the power constant. The proposed model fits the data well for low incident Mach numbers, while at higher mach numbers the presence of large and irregular late time oscillations of the perturbation amplitude makes it hard for the power law to fit as effectively. When the coefficients from the power law decay model are plotted versus Mach number, a distinct transition region can be seen. This region is likely to result from the transition of the post-shock heavy gas velocity from subsonic to supersonic range in the lab frame. This region separates the data into a high and low Mach number region. Correlations for the power law coefficients to the incident shock Mach number are reported for the high and low Mach number regions. It is shown that perturbations in the refracted shock wave persist even at late times for high incident Mach numbers.     

Numerical investigation of axisymmetric shock wave focusing over paraboloidal reflectors

The problem of a plane shock wave incident to a paraboloidal reflector is numerically investigated. The numerical solver used is developed by an improved, implicit, upwind total variation diminishing scheme in a finite-volume approach. The real-gas effect is taken into account if high temperature occurs. The solver is validated on four test problems. The complicated flow fields of axisymmetric shock wave focusing for different-depth reflectors at various incident shock Mach numbers are studied. An interesting result of a maximum pressure happening at the reflector center is found. This is due to the occurrence of an implosion phenomenon. A maximum temperature might occur at the reflector center or at other locations, depending on the incident shock Mach number and the reflector depth. Moreover, vortical flows induced by shock wave focusing and their formation mechanism are explored. It was found that the vortices near the reflector are caused by a ring-shaped shock/slipline interaction. Owing to the slipline on the symmetry axis, a jet flow is induced, resulting in the formation of vortices near the symmetry axis. Received 13 January 1998 / Accepted 10 November 1998     

可压缩流向涡与激波轴对称干扰的数值模拟

用ＮＳ方程数值模拟了可压缩流向涡和激波轴对称相互作用现象．数值模拟包括定常和非定常两种情况,计算结果分别与相应的实验进行了比较．结果表明数值模拟成功地捕捉到了激波和旋涡相互作用过程中发生的激波波面变形,激波振荡,涡核变大以及激波波后出现驻点、回流区等流场特征．提出了判断流向涡与运动激波相互作用中旋涡破碎的准则     

Guderley reflection for higher Mach numbers in a standard shock tube

An experimental study shows that the Guderley reflection (GR) of shock waves can be produced in a standard shock tube. A new technique was utilised which comprises triple point of a developed weak Mach reflection undergoing a number of reflections off the ceiling and floor of the shock tube before arriving at the test section. Both simple perturbation sources and diverging ramps were used to generate a transverse wave in the tube which then becomes the weak reflected wave of the reflection pattern. Tests were conducted for three ramp angles (10°, 15°, and 20°) and two perturbation sources for a range of Mach numbers (1.10–1.40) and two shock tube expansion chamber lengths (2.0 and 4.0 m). It was found that the length of the Mach stem of the reflection pattern is the overall vertical distance traveled by the triple point. Images with equivalent Mach stem lengths in the order of 2.0 m were produced. All tests showed evidence of the fourth wave of the GR, namely the expansion wave behind the reflected shock wave. A shocklet terminating the expansion wave was also identified in a few cases mainly for incident wave Mach numbers of approximately 1.20.     

Shock wave diffraction on multi-facetted and curved walls

The two-dimensional diffraction of a shock wave over a wall made up of a series of plane and/or curved sections is considered. The analysis is based on the theory presented by, for the interaction of an originally plane shock wave with a corner. A method is presented by which the shock profile may be determined for a wall of any shape and for any incident Mach number, in regions where the characteristics form a simple wave. Comparisons are made between experimental measurements and theoretical predictions for convex walls consisting of a number of facets, and for circular arcs, for a range of incident shock wave Mach numbers. It is shown that the theory gives a satisfactory prediction of the wave shape, which improves as the Mach number increases. Modifications in the flow field behind the shock, compared to that for a simple corner made up of two plane walls is discussed, particularly relating to flow separation. For circular arc concave walls a inverse Mach reflection results experimentally, leading to regular reflection, for which the theory is of no use. PACS 47.40.Nm     

EXPERIMENTALLY STUDY OF THE RICHTMYER-MESHKOV INSTABILITY AT N2/SF6 FLAT INTERFACES BY DIFFRACTED INCIDENT SHOCK WAVES AND RESHOCK

利用高速纹影测试实验研究低马赫数入射激波绕圆柱体后冲击N₂/SF₆平面界面,以及来自固壁的反射激波再冲击过程的（Richmyer-Meshkov,R-M）不稳定性特征.与平面激波作用不同的是,绕射后的激波会在界面处生成局部扰动.实验结果显示,入射激波作用下界面宽度增长缓慢,而反射激波再冲击后,局部扰动会产生大的“尖钉”和“气泡”结构;以及反射激波与边界层相互作用产生壁面涡,它们会加剧湍流混合区的增长;实验中反射激波过后混合区增长率不十分依赖于波前状态,增长规律同Mikaelian模型较吻合;来自尾部固壁的反射稀疏波会再次加剧湍流混合区的增长.     

Shock wave configurations and flow structures in non-axisymmetric underexpanded sonic jets

An experimental and numerical study of underexpanded free sonic jet flows issuing from rectangular, elliptical and slot nozzles has been undertaken. Aspect ratios (AR) of 1, 2, and 4 are described at pressure ratios (exit plane pressure to ambient pressure), of 2 and 3. There is good qualitative agreement between the experimental observations and the numerical predictions. In the case of rectangular jets, a complex system of shock waves forming the incident shock system is identified. This shock wave system originates at the corners of the nozzle exits, and proceeds downstream. Mach reflections are found to occur on the incident shock wave surface as well as the presence of a Mach disk terminating the first jet cell. This Mach disk has the shape of a square, a hexagon, or an octagon depending on the nozzle shape. For slot and elliptical jets, the formation of the incident shock wave was not observed along the minor axis plane of the nozzle for AR > 2. The incident shock wave was observed to originate downstream of the nozzle exit in the major axis plane. This wave system undergoes a transition to Mach reflection as it propagates downstream of the nozzle exit. In all cases tested, the shape of the jet boundary is significantly distorted. In rectangular jets, the narrowing of the jet boundary along the diagonal axis of the nozzle exit is observed, and in the case of the elliptical and slot jets axis switching is noted.     

Self-intensification in shock wave and vortex interaction

Computer simulation has been performed for the interaction between a shock wave and a vortex ring moving toward the wave. The computed density contours are compared with the pattern of shadowgraphs. A remarkable property found in the simulation is that, during the passage of the shock wave over the vortex ring, the part of the wave propagating through the inside of the ring-vortex is intensified spontaneously at a localized region. Maximum pressure occurs inside the vortex and attains a high value, about several times that of the impinging shock for incident Mach numbers of around 1.2 with the vortex translation Mach number 0.60. This is due to a double-step mechanism of intensification within the flow field by the shock-vortex interaction.     

A multiphase shock tube for shock wave interactions with dense particle fields

Currently there is a substantial lack of data for interactions of shock waves with particle fields having volume fractions residing between the dilute and granular regimes. To close this gap, a novel multiphase shock tube has been constructed to drive a planar shock wave into a dense gas–solid field of particles. A nearly spatially isotropic field of particles is generated in the test section by a gravity-fed method that results in a spanwise curtain of spherical 100-micron particles having a volume fraction of about 20%. Interactions with incident shock Mach numbers of 1.66, 1.92, and 2.02 are reported. High-speed schlieren imaging simultaneous with high-frequency wall pressure measurements are used to reveal the complex wave structure associated with the interaction. Following incident shock impingement, transmitted and reflected shocks are observed, which lead to differences in particle drag across the streamwise dimension of the curtain. Shortly thereafter, the particle field begins to propagate downstream and spread. For all three Mach numbers tested, the energy and momentum fluxes in the induced flow far downstream are reduced about 30–40% by the presence of the particle field.     

Correlation study in shock wave�Cturbulent boundary layer interaction

Shock wave–turbulent boundary layer interaction is a critical problem in aircraft design. Therefore, a thorough understanding of the processes occurring in such flows is necessary. The most important task is to study the unsteady phenomena, in particular, the low-frequency ones, for this interaction. An experimental study of separated flow has been performed in the zone of interaction of the incident oblique shock wave with a turbulent boundary layer at Mach 2. Two-point correlation data in the separation zone and the upstream flow were obtained and showed that low-frequency oscillations of the reflected shock waves are related to pulsations in the inflow turbulent boundary layer.     

A numerical study of oblique shock wave reflections over wedges in an ideal quantum gas

The various oblique shock wave reflection patterns generated by a moving incident shock on a planar wedge using an ideal quantum gas model are numerically studied using a novel high resolution quantum kinetic flux splitting scheme. With different incident shock Mach numbers and wedge angles as flow parameters, four different types of reflection patterns, namely, the regular reflection, simple Mach reflection, complex Mach reflection and the double Mach reflection as in the classical gas can be classified and observed. Both Bose–Einstein and Fermi–Dirac gases are considered.