Preparation and properties of thermosensitive hydrogel microcapsules

Temperature-sensitive hydrophilic gel microcapsules have been newly prepared. That is, poly ( -lysineisopropylamide–terephthalic acid) microcapsules containing water have been obtained by an interfacial polymerization at a water/oil interface between -lysineisopropylamide and terephthaloyldichloride. The microcapsule changes its size between 33 and 35°C. Under 33°C, the microcapsules are fully spherical and can be redispersed in distilled water, while are aggregated above 35°C. The microcapsules, which are observed to show aggregation above 33°C, can be redispersed by decreasing temperature within a few second. The thermosensitive morphological changes of the microcapsules are thus reversible. Also, it has been shown that the permeability of sodium chloride through the microcapsule membrane changes remarkably between 33 and 35°C, while it is kept almost constant independent of temperature between 25 and 33°C or between 35 and 55°C. The permeability of solutes is higher under 33°C than that above 35°C. Such thermosensitive properties result from the fact that the polymer membrane has isopropylamide groups. That is, -lysineisopropylamide has a chemical structure similar to N-isopropylacrylamide, the polymer of which, poly (N-isopropylacrylamide), is a thermosensitive hydrogel having its phase transition temperature around 33°C.     

Synthesis and characterization of thermosensitive copolymers for oral controlled drug delivery

Poly(N-isopropylacrylamide) (PNIPAAm) copolymers were synthesized in order to obtain co-polymers with a phase transition temperature slightly higher than the physiological temperature, as required by a new drug delivery concept described in a previous paper. Six hydrophilic comonomers bringing about a rise of the phase transition temperature were evaluated. The synthesized copolymers were characterized and the influence of the type and of the amount of the used comonomer on the phase transition temperature was discussed. Among the comonomers, Acrylamide (AAm), N-methyl-N-vinylacetamide (MVA), N-vinylacetamide (NVA), and N-vinyl-2-pyrrolidinone (VPL) were found to be capable to raise the phase transition temperature to a value slightly higher than 37 °C and to have adequate phase transition behavior. The selected four copolymers were subjected to an additional purification step that should make them fit to use as a controlling agent in drug delivery systems.     

Poly(N-isopropylacrylamide)/poly[(N-acetylimino)ethylene] thermosensitive block and graft copolymers

Block and graft copolymers with poly(N-isopropylacrylamide) and poly[(N-acetylimino)ethylene] (PNAI) sequences were synthesized via PNAI derivatives (macroinitiators or macromers). The polymerization yields for block copolymers synthesized in ethanol, using the PNAI macroinitiator, were low (<10%), except where photochemical polymerization was applied. By contrast, for the copolymerizations of N-isopropylacrylamide with the PNAI macromers, performed in alcoholic solution, quite high polymerization yields, around 80-90%, were reached. ¹H-NMR and IR spectral and differential scanning calorimeter thermal data confirmed the copolymer formation. Thermosensitivity of the copolymers was investigated by means of turbidimetric technique as a function of their nature, average molecular weight and composition. It was found that the length of the chain of the PNAI macromer and the content in hydrophilic PNAI units of the resulted copolymer affected this behavior.     

Aqueous solution behavior of p(N-isopropyl acrylamide) in the presence of water-soluble macromolecular species

We report here the polymerization of N-isopropyl acrylamide (NIPAM) via the reversible addition fragmentation chain transfer (RAFT) process. Two trithiocarbonates (S,S′-bis(α,α′-dimethyl-α″-acetic acid)-trithiocarbonate and 2-dodecylsulfanylthiocarbonylsulfanyl-2-methyl propionic acid) were used as the chain transfer agents in conjunction with 4,4′-azobis(4-cyanovaleric acid) and 2,2′azobis(2-methylpropionamidine) dihydrochloride as the initiating species. Poly(NIPAM) is a thermo-responsive polymer that has a sharp lower critical solution temperature (LCST). Herein, we investigated the aqueous solution behaviour of well defined p(NIPAM) prepared by the RAFT process as a function of molecular weight (degree of polymerization: 50, 100 and 200) and temperature. Furthermore, we examine the influence of varying concentrations of macromolecular species (neutral polyethylene glycol (M_n - 3400 g/mol) and ionic bovine serum albumin (M_n - 63 000 g/mol)) on the LCST of p(NIPAM). The aqueous solution behaviour was assessed by spectrophotometry, dynamic light scattering and surface tensiometry. The macromolecular additives was found to have a significant effect on the coil to globular transition of the lower molecular weight p(NIPAM).     

Hydrophobic modification of high molar mass polyglycidol to thermosensitive polymers

The results concerning a new class of thermosensitive polymers based on modified poly(2,3-epoxypropanol-1) - the polyglycidol are presented. Thermo-responsive water-soluble poly(glycidol-co-ethyl glycidyl carbamate)s were obtained by the hydrophobic modification of hydroxyl groups of the polyglycidol chain with ethyl isocyanate. The cloud points of the synthesized poly(glycidol-co-ethyl glycidyl carbamate)s were measured by UV-VIS and the hydrodynamic behaviour of the polymer chains near the transition temperature was characterized by dynamic light scattering. The influence of copolymer composition and polymer concentration on the cloud point was investigated. The cloud point was easy controlled in a range from 22 to 81 °C by change of the degree of modification. The effect of the surfactant sodium n-dodecylsulphate (SDS) and inorganic salt (NaCl) on the temperature response of synthesized copolymer was also examined.     

Synthesis and phase behavior of aqueous poly(N-isopropylacrylamide-co-acrylamide), poly(N-isopropylacrylamide-co-N,N-dimethylacrylamide) and poly(N-isopropylacrylamide-co-2-hydroxyethyl methacrylate)

Poly(N-isopropylacrylamide) (PNIPAM) and random copolymers of Poly(N-isopropylacrylamide-co-2-hydroxyethyl methacrylate) (PNIPAM-HEMA), poly(N-isopropylacrylamide-co-acrylamide) (PNIPAM-AAm), and poly(N-isopropylacrylamide-co-N,N-dimethylacrylamide) (PNIPAM-DMAA) with various volume fractions γ of NIPAM were synthesized by radical polymerization. The phase behavior of the polymers in water was investigated by means of optical transmittance and dynamic light scattering. With decreasing γ, the cloud point temperature T _cp for PNIPAM-HEMA decreased whereas the T _cp for both PNIPAM-AAm and PNIPAM-DMAA increased. Increase of hydrodynamic radius around T _cp, which resulted from the aggregation of the globules of each polymer, was observed from dynamic light scattering. The relationships between the reciprocal of T _cp of the polymer solutions and 1-γ were linear for the three copolymers in the experimental range of 0.65<γ<1. The results are discussed from the aspect of the interaction parameters of copolymer solutions.     

Lower critical solution temperature control and swelling behaviour of physically crosslinked thermosensitive copolymers based on N-isopropylacrylamide

In this contribution we have developed thermosensitive polymer matrices based on N-isopropylacrylamide (NIPAAm). Preparation of the hydrogels involved photopolymerisation of a combination of NIPAAm, 1-vinyl-2-pyrrolidinone (NVP) and distilled water, in appropriate amounts and contained a UV-light sensitive initiator called 1-hydroxycyclohexylphenylketone. As NIPAAm monomer could be readily dissolved in mixtures of liquid NVP and distilled water, the use of organic solvents was not required in the polymerisation process. Furthermore, chemical crosslinking agents are not needed in the synthesis. By alternating the feed ratio, hydrogels were synthesised to have lower critical solution temperatures (LCST) in the vicinity of 37 °C. This ability to shift the phase transition temperature of the gels provides excellent flexibility in tailoring transitions for specific uses. The transition temperature of the pseudo gels was established using cloud point measurement and modulated differential scanning calorimetry (MDSC). The chemical structure of the xerogels was characterised by means of Fourier transform infrared spectroscopy (Ftir), while swelling experiments in distilled water indicate that the swelling and dissolution behaviour of the gels is strongly temperature dependent.     

Fabrication of novel temperature and pH sensitive poly (N-isopropylmaleamic acid-co-acrylonitrile) hydrogels

To combine temperature and pH sensitive capabilities, N-isopropylmaleamic acid (NIPMMA), having isopropylamide group and weakly acidic group (–COOH), was synthesized and used as a precursor for fabrication of temperature and pH sensitive hydrogels. In this paper, a new class of intelligent hydrogel with pH and temperature sensitivity originated from only one precursor (NIPMMA) was designed and demonstrated. Resultant poly(NIPMMA-co-acrylonitrile) [P(NIPMMA-co-AN)] hydrogels were characterized by Fourier transform infrared spectroscopy for structural determination and scanning electron microscope for morphology observation. Their temperature and pH sensitive behaviors were also examined in detail. The data obtained exhibited that the magnitude of sensitive properties of P(NIPMMA-co-AN) hydrogels depended on the composition ratio of two precursors. By increasing the content of NIPMMA, the temperature and pH sensitive capabilities of P(NIPMMA-co-AN) hydrogels were improved correspondingly since AN has no sensitivity upon temperature or pH changes.     

Synthesis and swelling behavior of thermosensitive hydrogels based on N-substituted acrylamides and sodium acrylate

A series of hydrogels based on N-isopropylacrylamide, sodium acrylate, and N-tert-butylacrylamide were synthesized by free radical polymerization in a mixture of dioxane and water with tetra(ethylene glycol) diacrylate as the crosslinker and benzoyl peroxide as the initiator. The swelling behavior including the swelling rate of the crosslinked gels in water was studied with gravimetric method. The swelling ratio of the gel (0.1 mol% crosslinking) can reach 420 g/g at 20 °C and such a gel can release 96% of the water absorbed at 40 °C. The lower critical swelling temperature (LCST) of the copolymers can be adjusted by changing the chemical composition of the polymers. Such crosslinked gels can be potentially used as thermosensitive superabsorbent because of their high water uptake and thermal sensitivity.     

Monodisperse thermosensitive particles prepared by emulsifier-free emulsion polymerization with microwave irradiation

The emulsifier-free emulsion polymerization of styrene (St) and N-isopropylacrylamide (NIPAAm) was successfully carried out with microwave irradiation, and the monodisperse thermoresponsive poly(styrene-co-N-isopropylacrylamide) (poly(St-co-NIPAAm)) particles with diameters in the range 100–130 nm were prepared. The morphology, size and size distribution of the poly(St-co-NIPAAm) particles were characterized by transmission electron microscopy, scanning electron microscopy (SEM) and photon correlation spectroscopy (PCS), respectively. The results showed that poly(St-co-NIPAAm) particles had spherical morphology, and the poly(St-co-NIPAAm) particles prepared by emulsifier-free emulsion polymerization with microwave irradiation were smaller, more uniform than those obtained with conventional heating. The hydrodynamic diameters of poly(St-co-NIPAAm) particles were decreased as the temperature increased from 25 °C to 40 °C, and poly(St-co-NIPAAm) particles collapsed remarkably at 32 °C, which is the lower critical solution temperature of the poly(N-isopropylacrylamide). The morphology of the assembled poly(St-co–NIPAAm) particles was observed by SEM, it was found that monodisperse poly(St-co-NIPAAm) particles could assemble to form the two-dimensional order structures.     

Radiation grafting of pH and thermosensitive N-isopropylacrylamide and acrylic acid onto PTFE films by two-steps process

Polytetrafluoroethylene (PTFE) was grafted (g) with acrylic acid (AAc) by γ-ray pre-irradiation method to get PTFE-g-AAc films, then N-isopropylacrylamide (NIPAAm) was grafted onto PTFE-g-AAc films with γ-ray to get (PTFE-g-AAc)-g-NIPAAm. PTFE films were irradiated in air at a dose rate of 3.0 kGy h^–1 and different radiation dose. The irradiated films were placed in glass ampoules, which contained aqueous solutions with different monomer concentration (AAc), and then they were heated at different temperatures and reaction time. NIPAAm onto PTFE-g-AAc was carried out with the same procedure with monomer concentration of 1 mol L⁻¹. The thermosensitivity of the samples was defined and calculated as the ratio of the grafted samples swelling at 28 and 35 °C, and pH sensitivity defined as the ratio of the grafted samples swelling at pH 2 and 8.     

Drying dissipative structures of the thermosensitive gels of poly(N-isopropyl acrylamide) on a cover glass

Drying dissipative structural patterns of the thermosensitive gels of poly(N-isopropyl acrylamide) were studied on a cover glass. As the temperature of suspension and room rose from 25 to 50 °C, the small size of drying pattern area extended to the beautiful flickering spoke-like ones transitionally at the critical temperature ca. 35 °C. The principal patterns at 25 °C were the single or multiple broad rings of the hill accumulated with the gels. At 50 °C, on the other hand, the flickering spoke-like patterns were observed at the inner area of the broad ring especially at the gel concentrations higher than 1 × 10⁻³ g/ml. These observations support that the extended gels at low temperatures apt to associate weakly to each other, whereas the gels at high temperatures shrink and move rather freely with the convectional flow of water, though the very weak intergel attractions still remain. In the presence of sodium chloride at high temperatures, the cooperative patterns formed between the gel spheres and the salt. The gravitational and Marangoni convectional flow of the gels and the very weak interactions between the gels and substrate (cover glass) are important for the flickering spoke-like pattern formation.     

Thermosensitive polymeric vesicles self-assembled by PNIPAAm-b-PPG-b-PNIPAAm triblock copolymers

PNIPAAm-b-PPG-b-PNIPAAm triblock copolymers were prepared by redox polymerization. The self-assembly behavior and thermosensitive property of the copolymers in water were studied using ¹H-NMR, TEM and a UV spectrophotometer. The results showed that the LCST of the copolymers was 32 °C, which was consistent with that of pure PNIPAAm. The copolymers could form a vesicular structure in an aqueous solution by self-assembly. The hollow structure of the PNIPAAm-b-PPG-b-PNIPAAm vesicles combined with the temperature-sensitive property may enable many potential applications of the vesicles.     

A new strategy to prepare temperature-sensitive poly(<Emphasis Type="Italic">N</Emphasis>-isopropylacrylamide) microgels

In this study, a new method was developed to prepare temperature-sensitive poly(N-isopropylacrylamide) microgels by free radical precipitation polymerization using siloxane coupling agent as the new crosslinker. Ammonium persulfate acted as the initiator for the radical copolymerization as well as the catalyst for the hydrolysis/condensation of the siloxane groups. The particle diameter and polydispersity of the microgels were measured by photon correlation spectroscopy and the results display that the microgels are monodisperse. The microgels exhibit temperature sensitivity and the phase transition temperature is approximately 31 °C. Furthermore, the diameter of the microgels changes upon heating and cooling processes. These were observed to be reversible. The novel crosslinking method described herein is the condensation of siloxane groups, which is totally different from the traditional double-vinyl crosslinkers. This innovative approach offers an alternative path to prepare functional core–shell particles and inorganic/organic hybrid materials.     

Effect of filler networking on the response of thermosensitive composite hydrogels

Several composite hydrogels of poly(N-isopropylacrylamide) (pNIPAAm) with sodium montmorillonite (NaMM) have been synthesized using a fixed polymer/NaMM ratio (4:1 wt./wt.), but various monomer concentrations, in order to obtain hydrogels with different degrees of swelling, and thus different clay contents in the swollen state. For comparison, unfilled pNIPAAm gels have been also prepared at the same concentrations. The equilibrium swelling behaviour of the gels has been studied both in the swollen and in the shrunk state. In the swollen state, the polymer volume fraction increases with the initial monomer concentration C₀. In the shrunk state, the polymer fraction in pNIPAAm hydrogels is dependent on the specimen size and on C₀, whereas in the composite gels a constant polymer content is observed. When subjected to stepwise heating from 25 to 45 °C, unfilled gels undergo only poor deswelling. By contrast, complete deswelling takes place in composite gels. The latter show half-shrinking times varying over two orders of magnitude, depending on the monomer concentration and on the procedure followed to disperse NaMM, which determine the overall dispersion state of the filler, as evidenced by transmission electron microscopy (TEM). In particular, TEM observations show clay networking above a percolation threshold near 2.5 wt.% of NaMM. The effect of the incorporation of clay on the response to thermal stimuli is discussed in terms of the ability of NaMM to hinder the hydrophobic association of pNIPAAm segments and in terms of its dispersion state. It is suggested that, above the percolation threshold, NaMM forms a hydrophilic, physical network, through which water can flow also above the volume transition temperature, where pNIPAAm acquires a hydrophobic character.     

Preparation of a thermosensitive cobalt phthalocyanine/N-isopropylacrylamide copolymer and its catalytic activity on thiol

A thermosensitive copolymer of cobalt tetra(N-acryliccarbonyl)aminophthalocyanine (Co-TACAPc) and N-isopropylacrylamide (NIPA) was prepared through redox polymerization in aqueous solution, and its catalytic activity for oxidation of 2-mercaptoethanol was investigated. The products of Co-TACAPc and its copolymer were characterized by elemental analysis, IR, UV/vis, and TGA. The copolymer can be dissolved into most solvents, particularly into water over a wide range of pH. The copolymer also revealed a lower critical solution temperature (LCST) phenomenon at 32.6 degrees C in water; i.e., it was soluble in cold water (below 32.6 degrees C) but insoluble in hot water (above 32.6 degrees C). As a result, in contrast to Co-TACAPc, the copolymer is able to serve as a homogeneous catalyst on oxidation of 2-mercaptoethanol below 31.0 degrees C and be recovered with increasing temperature due to its lower solubility above 31.0 degrees C.     

Thermosensitive aggregates self-assembled by an asymmetric block copolymer of dendritic polyether and poly(N-isopropylacrylamide)

An asymmetric linear-dendritic block copolymer of polyether dendrimer and poly(N-isopropylacrylamide) was prepared by an atom transfer radical polymerization method. The self-assembly behavior and thermosensitive property of this copolymer in water were studied by dynamic light scattering (DLS), transmission electron microscopy (TEM) and fluorescence probe spectroscopy. It was found that the thermosensitive phase transition takes place at the temperature of 37.5 °C; simultaneously the spherical aggregates grow into larger entangled nanotubules. The unique temperature-sensitive supramolecular aggregates may make them especially useful as intelligent capsules for drug delivery systems and as chemical sensors.     

pH sensitivities of egg phosphatidylcholine liposomes and dioleoylphosphatidylethanolamine liposomes triggered by poly(<Emphasis Type="Italic">N</Emphasis>-isopropylacrylamide-co-methacrylic acid-co-octadecylacrylate)

Egg phosphatidylcholine (PC) liposomes bearing pH-sensitive polymers and dioleoylphosphatidylethanolamine (DOPE) liposomes including the same polymers were prepared by a sonication method. As pH-sensitive polymers, copolymers of N-isopropylacrylamide, methacrylic acid, and octadecylacrylate were used. The liposomes were stable in neutral pH ranges in terms of release. But the release became marked at pH 5.5, and it was accelerated as pH further decreased. For example, the degree of release from egg PC liposomes (polymer/lipid ratio is 3:10, w/w) for 120 s increased from 2% to 63% as pH decreased from 7.5 to 4.5. Under the same condition, the degree of release from DOPE liposomes increased from 4% to 80%. These results indicate that DOPE liposome is more pH-sensitive than egg PC liposome.     

Poly(<Emphasis Type="Italic">N</Emphasis>-vinylcaprolactam) microgels. Polymeric stabilization with poly(vinyl alcohol)

Poly(vinyl alcohol), PVA, with different molecular weights, M_w, and degrees of hydrolysis has been used to study the steric stabilization of microgels based on poly(N-vinylcaprolactam). The stabilizer influences the particle size and stability, but has no influence on the thermal properties. The thermal behavior of microgels depends on the heating rate: slow heating leads to the formation of aggregates and fast heating to an intramolecular collapse. The aggregates showed an unusual angular dependence of the diffusion coefficient, which can be explained by the presence of probably an additional rotational diffusion.     

Synthesis and characterization of thermo-sensitive poly (N-isopropylacrylamide) hydrogel with fast response rate

Thermo-sensitive poly (N-isopropylacrylamide) (PNIPA) hydrogel with fast response rate was prepared by polymerizing N-isopropylacrylamide (NIPA) in an aqueous hydroxyl-propyl-methyl cellulose solution. The volume phase transition temperature of PNIPA hydrogels was characterized by differential scanning calorimetry (DSC), and the surface morphology was observed by scanning electron microscopy (SEM). The swelling ratios of the hydrogels at different temperatures were measured. Furthermore, the deswelling kinetics of the hydrogels was also studied by measuring their water retention capacity. In comparison with a conventional PNIPA hydrogel prepared in water, the hydrogel synthesized in aqueous hydroxyl-propyl-methyl cellulose solution has higher swelling ratios at temperatures below the lower critical solution temperature and exhibits a much faster response rate to temperature changes. For example, the hydrogel made in aqueous hydroxyl-propyl-methyl cellulose solution lost 89% water within 1 min and about 93% water in 4 min, whereas the conventional hydrogel lost only about 66% water in 15 min from the deswelling measurement in similar conditions. Translated from Chinese Journal of Applied Chemistry, 2006, 23(6): 581–585 (in Chinese)