聚L-白氨酸修饰电极伏安法测定痕量多巴胺的研究

用循环伏安法制备了聚L-白氨酸修饰玻碳电极,研究了多巴胺在聚L-白氨酸修饰玻碳电极上的电化学行为,建立了循环伏安法测定痕量多巴胺的新方法。实验结果表明,在pH 6.0的磷酸盐缓冲溶液中,多巴胺在聚L-白氨酸修饰玻碳电极上产生一对灵敏的氧化还原峰,峰电位分别为Epa=0.281V,Epc=0.170 V(相对Ag/AgCl电极)。峰电流与多巴胺的浓度在5.0×10-8~5.0×10-4mol/L的范围内有线性关系,检出限为5.0×10-9mol/L。对1.0×10-5mol/L多巴胺溶液平行测定9次,其相对标准偏差为4.0%。已用于针剂中多巴胺的测定。     

黄嘌呤和鸟嘌呤在石墨烯-聚唑类化合物修饰电极上电化学行为

采用滴涂法和循环伏安法制备石墨烯-聚唑类化合物复合膜修饰玻碳电极,分别用循环伏安法和差分脉冲伏安法研究黄嘌呤和鸟嘌呤混合物在修饰电极上的电化学行为。在0.2 mol/L的磷酸盐缓冲液(p H 5.5)中,黄嘌呤和鸟嘌呤混合物在修饰的玻碳电极上具有较好的电化学行为。鸟嘌呤和黄嘌呤分别在4.0×10~(-4)~4.0×10~(-6)mol/L和4.0×10~(-5)~4.0×10~(-8)mol/L范围内有较好的电化学响应,鸟嘌呤和黄嘌呤检出限分别为4.0×10~(-7)mol/L和4.0×10~(-9)mol/L。方法用于同时测定人体尿液中鸟嘌呤和黄嘌呤,回收率分别为102.1%~105.9%和96.9%~106.5%。     

螺旋碳纳米管修饰电极对硫利达嗪的测定

螺旋碳纳米管(HCNTs)作为一种新型碳纳米材料具有比表面积大、催化性能好等特点。本文采用循环伏安法,研究了盐酸硫利达嗪(TR)在HCNTs修饰玻碳电极(HCNTs/GCE)上的电化学行为。HCNTs/GCE与裸玻碳电极及碳纳米管修饰的玻碳电极相比,对TR具有更强的催化氧化性能,其差分脉冲伏安法的峰电流与浓度在18.67~122.7μmol/L范围内呈良好的线性关系,检出限为5.120μmol/L。     

8-羟基脱氧鸟苷在壳聚糖/石墨烯修饰电极上的电化学及DNA氧化损伤检测

采用循环伏安(CV)、线性扫描伏安(LSV)和示差脉冲伏安(DPV)等方法研究了8-羟基脱氧鸟苷(8-OHdG)在壳聚糖(Chi)/石墨烯(GR)修饰的玻碳电极(GCE)上的电化学行为,8-OHdG在该修饰电极上氧化峰电流与其浓度在3.5×10-7~1.4×10-4mol/L范围内呈良好的线性关系,检测限为6.4×10-8mol/L(S/N=3)。将Chi/GR/GCE用于检测DNA氧化损伤,8-OHdG在修饰电极上的氧化峰电流与损伤的DNA质量浓度在10~300 mg/L范围内呈良好的线性关系,损伤DNA检出限为0.026 mg/L(S/N=3)。     

聚多巴胺-还原氧化石墨烯修饰电极同时测定邻苯二酚和对苯二酚

制备了聚多巴胺-还原氧化石墨烯修饰玻碳电极(PDA-rGO/GCE),以此修饰电极作为工作电极,采用循环伏安法(CV)对邻苯二酚(CC)和对苯二酚(HQ)的电化学行为进行了研究。结果表明CC和HQ在该修饰电极上的峰电流与氧化石墨烯修饰电极相比有了明显增高,并且它们的氧化峰电位差和还原峰电位差均超过110 mV,证明该修饰电极用于两种酚的同时检测是可行的。在优化实验条件下,采用微分脉冲伏安法(DPV)对CC和HQ同时进行检测,CC和HQ的峰电流与其浓度均在1.0×10~(-6)～4.0×10~(-3) mol/L范围内呈良好的线性关系,检出限(S/N=3)分别为2.0×10~(-7) mol/L和3.6×10~(-7) mol/L。以所制备的修饰电极对自来水水样和湖水水样进行了加标回收检测,回收率在97.6%～100.6%范围内。     

盐酸二甲双胍在β-CD/MWNTs修饰玻碳电极上的电化学行为研究

实验通过β-环糊精/多壁碳纳米管修饰玻碳电极测定盐酸二甲双胍,建立了一种电化学测定盐酸二甲双胍的新方法。裸玻碳电极聚合β-环糊精后用多壁碳纳米管修饰,然后研究盐酸二甲双胍在电极上的电化学行为,并测定盐酸二甲双胍。结果发现在p H7.2的磷酸盐缓冲溶液中,循环伏安曲线的峰电流与盐酸二甲双胍浓度在0.01~8 mg/m L范围内具有良好的线性关系(R2=0.9873),检出限为1.6×10-6mg/m L。该方法可用于盐酸二甲双胍缓释片含量的测定。     

阿昔洛韦在硼掺杂金刚石电极上的电化学行为及其与DNA相互作用的研究

利用硼掺杂金刚石(BDD)电极通过循环伏安法和微分脉冲伏安法研究了阿昔洛韦在0.10 mol/L磷酸盐缓冲溶液(pH 7.4)中的电化学行为及其与DNA的相互作用.与玻碳电极相比,阿昔洛韦在BDD电极上的循环伏安曲线在1.17 V处的氧化峰电流更大,背景电流较低.根据峰电位随溶液pH值和扫描速率的变化趋势考察了阿昔洛韦...     

电化学还原的氧化石墨烯修饰电极检测L-色氨酸

制备了氧化石墨烯修饰玻碳电极,并运用循环伏安法对氧化石墨烯进行了直接的电化学还原,研究了L-色氨酸在该电化学还原的氧化石墨烯修饰玻碳电极上的电化学行为。结果表明,L-色氨酸在该修饰电极上其氧化峰电流与裸玻碳电极相比增大了7.1倍,且峰电位负移80mV。利用差分脉冲伏安法,在pH=6.5的磷酸盐缓冲溶液中测定L-色氨酸,氧化峰电流与其浓度在0.4～65.0μmol/L范围内呈良好的线性关系,相关系数为0.998,方法检出限为0.2μmol/L。     

聚L-精氨酸修饰电极存在下同时测定多巴胺和肾上腺素

用循环伏安法制备了聚L-精氨酸修饰玻碳电极,研究了多巴胺和肾上腺素在修饰电极上的电化学行为,建立了同时测定多巴胺和肾上腺素的新方法。在pH7.5的磷酸盐缓冲溶液中,多巴胺在修饰电极上产生一对氧化还原峰,峰电位分别为0.276V和0.059V;肾上腺素在修饰电极上产生3个氧化峰和一个还原峰,峰电位分别为0.262V、0.121V、-0.126V和-0.316V(对Ag/AgCl电极)。多巴胺和肾上腺素同时存在时ΔEpc=375mV,用还原峰对多巴胺和肾上腺素同时测定的线性范围分别为8.0×10-7~5.0×10-4mol/L和5.0×10-7~5.0×10-5mol/L;检出限分别为3.0×10-7mol/L和1.0×10-7mol/L。大量的抗坏血酸和尿酸不干扰测定,用于人尿液中多巴胺和肾上腺素样品的同时测定,结果满意。     

聚L-赖氨酸修饰电极循环伏安法测定药剂中的多巴胺

用循环伏安法制备了聚L-赖氨酸修饰玻碳电极,研究多巴胺在聚L-赖氨酸修饰电极上的电化学行为,建立了循环伏安法测定多巴胺的新方法。实验结果表明,在pH7.0的磷酸盐缓冲溶液中,扫描速率为150mV/s,循环扫描电位在-0.3~0.6V时,多巴胺在聚L-赖氨酸修饰玻碳电极上出现一对灵敏的氧化还原峰,峰电位分别为Epa=0.175V,Epc=0.146V(相对饱和甘汞电极);测定多巴胺的线性范围为1.0×10-3~1.0×10-5mol/L和1.0×10-5~8.0×10-9mol/L,方法检出限1.0×10-9mol/L。用于药剂中多巴胺的测定。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Thermodynamics of the formation of oxosulfides of rare-earth elements

The enthalpies of solution of several oxosulfides of rare-earth elements and the high-temperature enthalpies of oxosulfides and oxosulfates of lanthanum and yttrium were measured using solution calorimetry and high-temperature microcalorimetry techniques. Standard enthalpies of formation and some thermodynamic properties of oxosulfides and oxosulfates were calculated. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2 pp. 294–297, February, 1997.     

探究“铁的锈蚀条件”实验创新设计

设计了铁的锈蚀实验,说明了铁钉的处理方法,增加了温度、酸、碱的影响条件,实现了铁跟蒸馏水及空气中氧气快速反应而生锈,使实验在5 min左右就能够得到准确的结果。