Preparation of Polyethylene/Graphene Nanocomposites with Octadecylamine‐Modified Graphene Oxide‐MgCl‐Supported Ziegler–Natta Catalyst

In this work, an octadecylamine‐modified graphene oxide (ODA‐GO)‐MgCl‐supported Ziegler–Natta catalyst was synthesized by reacting ODA‐GO with a Grignard reagent, followed by anchoring TiCl₄ to the structure. The effect of the ODA‐GO on the catalyst morphology and ethylene polymerization behavior was examined. The resultant polyethylene (PE)/ODA‐GO nanocomposites directly mirrored the catalyst morphology by forming a layered morphology, and the ODA‐GO fillers were well dispersed in the PE matrix and showed strong interfacial adhesion with it. The resultant PE/ODA‐GO nanocomposites exhibited better thermal stability and mechanical properties than neat PE, even with a small amount of ODA‐GO added. Thus, this work provides a facile approach to the production of high‐performance PE. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 855–860     

Chitosan‐modified graphene oxide as a modifier for improving the structure and performance of forward osmosis membranes

Chitosan (CS) with good hydrophilicity and charged property was used to modify graphene oxide (GO), the obtained GO‐CS was used as a novel modifier to fabricate thin film composite forward osmosis (FO) membranes. The results revealed that the amino groups on CS reacted with carboxyl groups on GO, and the lamellar structure of the GO nanosheets was peeled off by CS, resulting in the reducing of their thicknesses. The GO‐CS improved the hydrophilicity of polyethersulfone (PES) substrate, and their contact angles decreased to 64° with the addition of GO‐CS in the substrate. GO‐CS also increased the porosity of the substrate and surface roughness of FO membrane, thereby optimizing the water flux and reverse salt flux of FO membrane. The average water flux of the FO membrane reached the optimal flux of 21.34 L/(m² h) when GO‐CS addition was 0.5 wt%, and further addition of GO‐CS to the substrate would decrease the water flux of FO membrane, and the reverse salt flux also decreased to the lowest value of 2.26 g/(m² h). However, the salt rejection of the membrane increased from 91.4% to 95.1% when GO‐CS addition increased from 0.5 to 1.0 wt% under FO mode using 1 mol/L sodium chloride (NaCl) solution as draw solution (DS). In addition, high osmotic pressure favored water permeation, and at the same concentration of DS, magnesium chloride (MgCl₂) exhibited better properties than NaCl. These results all suggested that GO‐CS was a good modifier to fabricate FO membrane, and MgCl₂ was a good DS candidate.     

Surface roughness and hydrophilicity enhancement of polyolefin‐based membranes by three kinds of plasma methods

The introduction of antibacterial property, conductivity, wettability and antithrombogenicity into polyolefin‐based membranes has evoked much attention, which can be achieved by coating hydrophilic polymers. Therefore, it is necessary to modify the roughness and hydrophilicity of polyolefin‐based membranes to enhance the coating ability. In this paper, three kinds of plasma methods, including inductively coupled (ICP) plasma, radio frequency low pressure (RFP) plasma and atmospheric dielectric barrier discharge (DBD) plasma, were used to modify the surface of the polyethylene (PE), polypropylene (PP) and polyester‐polypropylene (PET–PP) membranes. The surface roughness of the plasma‐modified PE, PP and PET–PP films was investigated by scanning electron microscopy (SEM) and atomic force microscope (AFM). The polar functional groups of films were observed by energy dispersive spectrometer (EDX) and X‐ray photoelectron spectroscopy (XPS). Besides, the hydrophilicity of the plasma‐modified PE, PP and PET–PP films was evaluated by water contact angle measurement. It was found that the surface roughness and hydrophilicity of plasma‐modified PE, PP and PET–PP films increased with the generation of oxygen‐containing functional groups (i.e. C―O, and C?O). The PET–PP membranes were treated by RFP plasma at different processing powers and times. These results indicated that plasma is an effective way to modify films, and the treatment time and power of plasma had a certain accumulation effect on the membranes' hydrophilicity. As for the roughness and hydrophilicity, the DBD plasma modifies the PE film, which is the optimum way to get the ideal roughness and hydrophilicity. Copyright © 2015 John Wiley & Sons, Ltd.     

Anchoring calcium carbonate on graphene oxide reinforced with anticorrosive properties of composite epoxy coatings

Calcium carbonate nanoparticles (nano‐CaCO₃) anchored graphene oxide (GO) sheet nanohybrids (GO‐CaCO₃) are fabricated, and their structure can be measured by scanning electron microscope, transmission electron microscopy, X‐ray photoelectron spectroscopy, X‐ray diffraction and Fourier‐transform infrared spectroscopy analysis. Afterwards, composite epoxy coatings, filled with GO and GO‐CaCO₃ nanohybrids, are prepared via a curing process. The dispersion and anticorrosive properties of composite epoxy coatings are investigated. The results reveal that GO‐CaCO₃ nanohybrids achieve a homogeneous dispersion as well as reinforce corrosion resistance of epoxy coatings. Furthermore, the anticorrosive mechanisms are tentatively proposed for the GO‐CaCO₃/epoxy coatings. Copyright © 2016 John Wiley & Sons, Ltd.     

Surface properties of biospecific coatings based on polyelectrolyte complexes of maleic acid copolymers

The surface properties of PE with bilayer and multilayer coatings based on polyelectrolyte complexes of the biospecific modified N-vinylpyrrolidone-maleic acid copolymer with chitosan, amphiphilic chitosan, or albumin have been investigated by atomic force microscopy, multiple attenuated total reflection spectroscopy, X-ray photoelectron spectroscopy, and goniometry. The copolymer of N-vinylpyrrolidone and maleic acid contains affine ligands to plasminogen—fragments of α-amino-bonded lysine—and imparts thromboresistant properties to the surface being modified. The surface morphology and the size of particles of deposited intermediate layers of chitosan or albumin differ from those of the bilayer (multilayer) coatings containing an additional external layer of the biospecific copolymer. The deposition of the multilayer polymeric coatings promotes a more thorough coverage of the protected surface. Characteristic absorption bands that demonstrate the presence of the modifying polymers on the PE surface have been revealed; this fact is also confirmed by the X-ray photoelectron spectroscopy data on the atomic composition of the analyzed surface. A significant increase in the hydrophilicity of the modified surface is established by the contact angle technique.     

Ionic liquid functionalized graphene oxide for enhancement of styrene‐butadiene rubber nanocomposites

Ionic liquid 1‐allyl‐3‐methyl‐imidazolium chloride (AMICl) is used to fine‐tune the surface properties of graphene oxide (GO) sheets for fabricating ionic liquid functionalized GO (GO‐IL)/styrene‐butadiene rubber (SBR) nanocomposites. The morphology and structure of GO‐IL are characterized using atomic force microscope, X‐ray diffraction, differential scanning calorimetry, X‐ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, UV‐vis spectra and Raman spectra. The interaction between GO and AMICl molecules as well as the effects of GO‐IL on the mechanical properties, thermal conductivity and solvent resistance of SBR are thoroughly studied. It is found that AMICl molecules can interact with GO via the combination of hydrogen bond and cation–π interaction. GO‐IL can be well‐dispersed in the SBR matrix, as confirmed by X‐ray diffraction and scanning electron microscope. Therefore, the SBR nanocomposites incorporating GO‐IL exhibit greatly enhanced performance. The tensile strength, tear strength, thermal conductivity and solvent resistance of GO‐IL/SBR nanocomposite with 5 parts per hundred rubber GO‐IL are increased by 505, 362, 34 and 31%, respectively, compared with neat SBR. This method provides a new insight into the fabrication of multifunctional GO‐based rubber composites. Copyright © 2016 John Wiley & Sons, Ltd.     

Silicone-enriched surface of immersed polyurethane-POSS antifouling coating

Abstract

A series of waterborne polyurethane-polyhedral oligomeric silsesquioxane (WBPU-POSS) dispersions were synthesized. Different POSS contents were used to evaluate the effect of POSS content on silicone enrichment under both nonimmersed and immersed conditions. The impact of silicone enrichment under immersed conditions on antifouling properties was also evaluated. The structure of the WBPU-POSS coating was identified by FT-IR and ²⁹Si-NMR. X-ray photoelectron spectroscopy (XPS) analysis confirmed a silicone-enriched surface with a certain composition of the WBPU-POSS coating under both nonimmersed and immersed conditions. The mechanical properties, hydrophilicity and hydrolytic degradation of the coating all varied with POSS content. The long-term antifouling performance of immersed coatings depends on surface silicone enrichment, which was found to be above 0.0021?mole POSS content in WBPU-POSS coatings.     

Interfacial structure and tribological behaviours of epoxy resin coating reinforced with graphene and graphene oxide

Graphene (G) and graphene oxide (GO) were added into epoxy resin (EP) respectively via chemical modification and physical ultrasound technology to improve the tribological behaviour of EP coating. The topographies of G and GO were detected by scanning probe microscopy. The chemical structures of the fillers before and after modification were identified by Fourier transform infrared spectrometer. The across‐section topographies of the coatings were detected by scanning electron microscopy. The tribological behaviour of the coatings was evaluated by UMT‐3 tribology tester, surface profiler and scanning electron microscopy. The results revealed that the coefficient of friction of the coatings decreased, and the wear resistance of the coatings improved with the addition of the G and GO. GO could improve the tribological performance of EP further compared to G. When containing 0.5 wt% G and 0.75 wt% GO, the coatings had the lowest coefficient of friction and best wear resistance. When the contents of G reached 0.75 wt%, and GO reached 1 wt%, the tribological performance of the composite coatings decreased as a result of the agglomeration of the fillers. Finally, the anti‐friction and anti‐wear mechanisms of G‐EP and GO‐EP composite coatings were discussed in detail based on the results obtained in the preceding texts. Copyright © 2016 John Wiley & Sons, Ltd.     

Progress in preparation,characterization, surface functional modification of graphene oxide: A review

Graphene oxide (GO) has become the focus of scientific research due to unique mechanical, optical, electrical and chemical properties. We review the synthesis approaches and formation mechanism of GO, and propose that the crucial factor to the preparation of GO is to find efficient and environmentally friendly oxidant. Various characterization techniques are introduced, and characteristics are summarized. The GO model theories are synopsized, and determining the structure of GO has important influence on its surface modification and its application and development in composite materials. The interaction and reaction types between GO matrix and modified molecules, as well as the properties of modified products were described. In conclusion, the present challenges and future research directions are presented in terms of preparation and surface functional modification for GO.     

Superhydrophobic conducting coatings based on silicone matrix and carbon nanotubes

Preparation of superhydrophobic conducting coatings based on silicone matrix and two types of carbon nanotubes, native and modified with alkyl groups, is described. The amount of carbon nanotubes per unit surface area was kept constant in all the samples, whereas the content of the polymer matrix was varied. The electrical conductivity, contact angle, and sliding angle were measured. The structure of the coatings was studied with an optical profilometer and a scanning electron microscope. The largest contact angle was 158.4° for the sample with 50 wt % content of native carbon nanotubes. For the samples with more than 20 wt % content of carbon nanotubes of both types, the sliding angle was less than 1°. Changes in the micro- and nanostructure of the coatings, observed with variation of the content of the polymer matrix in the samples, were studied. The relationship between the structural changes, on the one hand, and hydrophobic and water sliding properties of the conducting coatings, on the other hand, was demonstrated.     

Preparation of antifog and antibacterial coatings by photopolymerization

This paper contains a kind of ultraviolet‐cured antifogging and antibacterial coating. A quaternary ammonium salt (14QAS), which was synthesized in this paper, has been implemented as a monomer. The chemical structure of 14QAS has been confirmed by Fourier transform infrared spectroscopy and nuclear magnetic resonance. The nitrogen atom on the surface of the coatings with 14QAS was observed by X‐ray photoelectron spectroscopy. The Surface wettability of the polymer film was studied by contact angle analysis, which confirmed the hydrophilicity of the coatings with low water contact angle (~25°). The antifog properties were evaluated under different conditions. The antibacterial activity of coatings with 14QAS reached 99.9% against S. aureus and E. coli. Copyright © 2014 John Wiley & Sons, Ltd.     

In situ polymerization and characterization of graphene oxide‐co‐poly(phenylene benzobisoxazole) copolymer fibers derived from composite inner salts

A facile and efficient strategy for preparing well dispersed graphene oxide (GO)‐co‐Poly(phenylene benzobisoxazole) (PBO) copolymer fibers was carried out by direct in situ polycondensation of composite inner salts. The composite inner salts were achieved to improve the dispersivity, solubility, reactivity, and interfacial adhesion of GO in PBO polymer matrix. The structure and morphology of GO‐co‐PBO copolymer fibers have been characterized. It was demonstrated that GO were covalently incorporated with PBO molecular chains and dispersed considerably well in PBO fiber even the GO reach to 3 wt %. Meanwhile, the tensile modulus, tensile strength and thermal stability of GO‐co‐PBO copolymer fibers increased considerably with GO. The mechanism and theoretical calculation of GO enhanced PBO fiber were also discussed. The main reasons for the improvement on performance of PBO fiber should be attributed to good dispersion GO in PBO matrix and covalent bonding networks at the interface between GO and PBO molecular chains. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

A Molecular Pillar Approach To Grow Vertical Covalent Organic Framework Nanosheets on Graphene: Hybrid Materials for Energy Storage

Hybrid 2D–2D materials composed of perpendicularly oriented covalent organic frameworks (COFs) and graphene were prepared and tested for energy storage applications. Diboronic acid molecules covalently attached to graphene oxide (GO) were used as nucleation sites for directing vertical growth of COF‐1 nanosheets (v‐COF‐GO). The hybrid material has a forest of COF‐1 nanosheets with a thickness of 3 to 15 nm in edge‐on orientation relative to GO. The reaction performed without molecular pillars resulted in uncontrollable growth of thick COF‐1 platelets parallel to the surface of GO. The v‐COF‐GO was converted into a conductive carbon material preserving the nanostructure of precursor with ultrathin porous carbon nanosheets grafted to graphene in edge‐on orientation. It was demonstrated as a high‐performance electrode material for supercapacitors. The molecular pillar approach can be used for preparation of many other 2D‐2D materials with control of their relative orientation.     

Effects of curing agents and modified graphene oxide on the properties of XNBR composites

This paper investigates the effects of crosslinking methods on the incorporation of graphene oxide (GO) in carboxylated nitrile butadiene rubber (XNBR) in the process of producing nanocomposites for chemical-resistant protective clothing and gloves. The novel aspect of the study is a comprehensive approach involving both unmodified GO as well as GO that was carboxylated to increase its affinity to XNBR and to facilitate its application. The nanostructure of XNBR composites was characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM). Fourier transform infrared spectroscopy (FTIR) was used to elucidate the chemical structure of the composites. Thermal stability studies were performed using differential scanning calorimetry (DSC). The barrier properties of the composites were determined based on swelling, crosslinking density, and permeation by mineral oils. The mechanical tests included resistance to puncture and abrasion, stress at strain, and tensile strength. Contact angle was measured to determine the degree of hydrophobicity of the obtained composites.AFM and SEM images revealed the effects of different curing agents (sulfur, magnesium oxide, or a hybrid system) as well as GO type on the surface morphology of XNBR composites. The type of curing agent was found to affect the kind of crosslinks formed and their spatial network structure, as confirmed by FTIR. The DSC curves showed that the crosslinking methods of XNBR did not affect glass transition temperature, but led to large changes observed in the temperature range of 130–220 °C.The type of crosslinking method affected the degree of swelling. It was found that the incorporation of carbon nanofillers led to an improvement in the abrasion and puncture resistance as well as tensile strength of XNBR composites. The water contact angle of the composites indicated hydrophobicity. The properties of XNBR composites containing GO revealed their substantial application potential in protective clothing.     

Synergistic effect of functional carbon nanotubes and graphene oxide on the anti‐corrosion performance of epoxy coating

In this work, we reported the synergistic effect of functional carbon nanotubes (CNTs) and graphene oxide (GO) on the anticorrosion performance of epoxy coating. For this purpose, the GO and CNTs were firstly modified by the 3‐aminophenoxyphthalonitrile to realize the nitrile functionalized graphene oxides (GO‐CN) and carbon nanotubes (CNTs‐CN). As modified GO‐CN and CNTs‐CN were characterized and confirmed by Fourier transform infrared spectroscopy, X‐ray photoelectron spectroscopy, and gravimetric analyzer. It was found that about 19 and 24 wt% of 3‐aminophenoxyphthalonitrile were grafted onto the surface of the GO and CNTs, respectively. The electrochemical impedance spectroscopy results showed that the GO‐CN&CNTs‐CN hybrid materials exhibit a remarkable superiority in enhancing the anticorrosion performance of epoxy coatings. Significant synergistic effect of the lamellar structural GO‐CN and CNTs‐CN on the anticorrosion performance of epoxy composite coatings was designed. Besides, the epoxy coating with 1 wt% of the GO‐CN&CNTs‐CN hybrid exhibited the best anticorrosion performance, in which the impedance showed the largest one (immersion in 3.5 wt% of NaCl solution for 168 hr). Copyright © 2016 John Wiley & Sons, Ltd.     

Concentration‐dependent conformation transition of regenerated silk fibroin induced by graphene oxide nanosheets incorporation

Regenerated silk fibroin (RSF)/graphene oxide (GO) nanocomposite has been substantially investigated due to its significant multifunctional potential. Here, in combination of micromorphology, crystalline conformation, dynamic mechanical property characterization, and Fourier self‐deconvolution (FSD) quantitative analysis, we investigated the RSF molecular chains conformation transition induced by GO nanosheet incorporation, and its influence on the structural and mechanical properties of solution casted RSF/GO composite films. The GO nanosheet promoted the silk fibroin molecular chains conformation transition from random coil to β‐sheet structure, and a correlation between β‐sheet structure fraction and GO concentration was revealed. The β‐sheet structure fraction increases further improved the dynamic mechanical property of composite films. Moreover, based on nucleation‐dependent aggregation of silk fibroin molecular chains, a mechanism considering the competition effect between GO concentration and its total surface area was proposed to explain the observed concentration‐dependent conformation transition phenomenon. The study improves our understanding on silk fibroin conformation transition process in RSF/GO composite and would provide a valuable reference for the rational design of bioinspired multifunctional materials with enhanced mechanical properties. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1506–1515     

Tribological properties of poly(phthalazione ether sulfone ketone) composites reinforced with glass fabric modified by graphene oxide depositing

In this paper, by electrophoretic deposition of graphene oxide (GO) on the surface of high‐strength glass fabric, a new fabric/poly(phthalazione ether sulfone ketone) (PPESK) composites material was successfully fabricated. The effects of GO on the interfacial adhesion, interlaminar shear strength, and tribological properties of the composites were investigated. Because of the addition of GO, the interlaminar shear strength of the composites was enhanced by 36.04%. Besides, the scanning electron microscope observation revealed that the interfacial adhesion between PPESK matrix and glass fabric was greatly improved. Attributing to the good interfacial adhesion, the wear‐resistance of the fabric/PPESK composite was greatly enhanced. Moreover, it can be found that the failure location transferred from the interface to the matrix after GO deposition.     

Dual-functional ROMP-based betaines: effect of hydrophilicity and backbone structure on nonfouling properties

Foundational materials for nonfouling coatings were designed and synthesized from a series of novel dual-functional zwitterionic polymers, Poly[NRZI], which were easily obtained via ring-opening metathesis polymerization (ROMP) followed by a single step transformation of the cationic precursor, Poly[NR(+)], to the zwitterion, Poly[NRZI]. The resulting unique dual-functional structure contained the anion and the cation within the same repeat unit but on separate side chains, enabling the hydrophilicity of the system to be tuned at the repeat unit level. These dual-functional zwitterionic polymers were specifically designed to investigate the impact of structural changes, including the backbone, hydrophilicity, and charge, on the overall nonfouling properties. To evaluate the importance of backbone structure, and as a direct comparison to previously studied methacrylate-based betaines, norbornene-based carbo- and sulfobetaines (Poly[NCarboZI] and Poly[NSulfoZI]) as well as a methacrylate-based sulfobetaine (Poly[MASulfoZI]) were synthesized. These structures contain the anion-cation pairs on the same side chain. Nonfouling coatings were prepared from copolymers, composed of the zwitterionic/cationic precursor monomer and an ethoxysilane-containing monomer. The coatings were evaluated by using protein adsorption studies, which clearly indicated that the overall hydrophilicity has a major influence on the nonfouling character of the materials. The most hydrophilic coating, from the oligoethylene glycol (OEG)-containing dual-functional betaine, Poly[NOEGZI-co-NSi], showed the best resistance to nonspecific protein adsorption (Γ(FIB) = 0.039 ng/mm(2)). Both norbornene-based polymers systems, Poly[NSulfoZI] and Poly[NCarboZI], were more hydrophilic and thus more resistant to protein adsorption than the methacrylate-based Poly[MASulfoZI]. Comparing the protein resistance of the dual-functional zwitterionic coatings, Poly[NRZI-co-NSi], to that of their cationic counterparts, Poly[NR(+)-co-NSi], revealed the importance of screening electrostatic interactions. The adsorption of negatively charged proteins on zwitterionic coatings was significantly less, despite the fact that both coatings had similar wetting properties. These results demonstrate that the unique, tunable dual-functional zwitterionic polymers reported here can be used to make coatings that are highly efficient at resisting protein adsorption.     

The Structural Influence of Graphene Oxide on Its Fragmentation during Laser Desorption/Ionization Mass Spectrometry for Efficient Small‐Molecule Analysis

The structural influence of graphene oxide (GO) on laser desorption/ionization mass spectrometry (LDI‐MS) analysis of small molecules was systematically investigated by using size‐fractionated GO. For fractionation of GO, pH‐assisted centrifugation, sequential vacuum filtration, and sonochemical cutting processes were employed and the size‐fractionated GO was thoroughly characterized to understand their size‐dependent optochemical properties. Then, the fractionated GO was applied to the analysis of various small molecules by LDI‐MS to investigate the relationship between their optochemical properties and LDI‐MS performance. We found that large GO sheets (>0.5 μm) were more prone to fragmentation under laser irradiation during LDI‐MS analysis than small GO sheets (<0.5 μm). In this regard, the LDI‐MS analysis efficiency of various small molecules was significantly improved by using nanosized GO (NGO) as a matrix without background interference. In particular, NGO was successfully applied to the sensitive detection of hydrophobic pollutant molecules without requiring any surface‐functionalization, enrichment, and separation process. Therefore, the present study could provide important basic information and be a practical tool for the development of simple and efficient LDI‐MS platforms by using GO derivatives.     

An inorganic route to decorate graphene oxide with nanosilica and investigate its effect on anti‐corrosion property of waterborne epoxy

This paper reported an inorganic route that uses potassium silicate, which is one type of alkali silicate as an inorganic modifier, taking advantage of its instability and water condensation to decorate graphene oxide (GO) with nano‐SiO₂. The ingredients of prepared nanocomposites were characterized by Fourier‐transform infrared spectroscopy (FT‐IR) and X‐ray photoelectron spectroscopy (XPS), and the thermodynamic property was tested by thermal gravimetric analysis (TGA). Scanning electron microscopy (SEM) was used to observe the morphology of SiO₂‐GO nanocomposites. All the analyses above revealed the nano‐SiO₂ (<100 nm) was deposited on the surface of GO by chemical bonds. In the meantime, the dispersion test illustrated that nano‐SiO₂ played an important role in improving the dispersity of GO. The effect of SiO₂‐GO nanocomposites on barrier and corrosion protection performance of SiO₂‐GO nanocomposites was tested by immersion experiment and electrochemical impedance spectroscopy (EIS). The results indicated that GO was helped to block the corrosion of aggressive medium; moreover, SiO₂‐GO nanocomposites had the best anticorrosion performance and the slowest rate of corrosion because of its good dispersity with waterborne epoxy coatings.