In this study, poly(lactic acid) (PLA)/starch blends were prepared through reactive melt blending by using PLA and starch as raw materials and vegetable oil polyols, polyethylene glycol (PEG), and citric acid (CA) as additives. The effects of CA and PEG on the toughness of PLA/starch blends were analyzed using a mechanical performance test, scanning electron microscope analysis, differential scanning calorimetry, Fourier-transform infrared spectroscopy, X-ray diffraction, rheological analysis, and hydrophilicity test. Results showed that the elongation at break and impact strength of the PLA/premixed starch (PSt)/PEG/CA blend were 140.51% and 3.56 kJ·m−2, which were 13.4 and 1.8 times higher than those of pure PLA, respectively. The essence of the improvement in the toughness of the PLA/PSt/PEG/CA blend was the esterification reaction among CA, PEG, and starch. During the melt-blending process, the CA with abundant carboxyl groups reacted in the amorphous region of the starch. The shape and crystal form of the starch did not change, but the surface activity of the starch improved and consequently increased the adhesion between starch and PLA. As a plasticizer for PLA and starch, PEG effectively enhanced the mobility of the molecular chains. After PEG was dispersed, it participated in the esterification reaction of CA and starch at the interface and formed a branched/crosslinked copolymer that was embedded in the interface of PLA and starch. This copolymer further improved the compatibility of the PLA/starch blends. PEGs with small molecules and CA were used as compatibilizers to reduce the effect on PLA biodegradability. The esterification reaction on the starch surface improved the compatibilization and toughness of the PLA/starch blend materials and broadens their application prospects in the fields of medicine and high-fill packaging. 相似文献
Crosslinked polyvinyl alcohol (PVA) and chitosan polymer blends have been prepared by using gamma irradiation. Chitosan was used in the blends to prevent microbiological growth, such as bacteria and fungi on the polymer. The physical properties of the blend, such as gelation, water absorption, and mechanical properties were examined to evaluate the possibility of its application for wound dressing. A mixture of PVA/chitosan, with different ratios, were exposed to gamma irradiation doses of 20, 30, 50 KGy, to evaluate the effect of irradiation dose on the physical properties of the blend. It was found that the gel fraction increases with increasing irradiation dose and PVA concentration in the blend. Swelling percent increased as the composition of chitosan increased in the blend. The PVA/chitosan blend has a water content in the range between 40% and 60% and water absorption between 60% and 100%. The water vapor transmission rate value (WVRT) of the PVA/chitosan blend varies between 50% and 70%. The examination of the microbe penetration shows that the prepared blend can be considered as a good barrier against microbes. Thus, the PVA/chitosan blend showed satisfactory properties for use as a wound dressing. 相似文献
Ricinoleic acid (RA) has potential to promote wound healing because of its analgesic and anti‐inflammatory properties. This study investigates the synthesis and characterization of RA liposomes infused in a hydrogel for topical application. Lecithin liposomes containing RA were prepared and incorporated into a chitosan solution and were subsequently cross‐linked with di‐aldehyde β‐cyclodextrin (Di‐β‐CD). Chitosan/Di‐β‐CD concentrations and reaction temperatures were varied to alter gelation time, water content, and mechanical properties of the hydrogel in an effort to obtain a wide range of RA release profiles. Hydrogel cross‐linking was confirmed by spectroscopy, and liposome and carrier hydrogel morphology via microscopy. Chitosan, Di‐β‐CD, and liposome concentrations within the formulation affected the extent of matrix swelling, mechanical strength, and pore and overall morphology. Higher cross‐linking density of the hydrogel led to lower water uptake and slower release rate of RA. Optimized formulations resulted in a burst release of RA followed by a steady release pattern accounting for 80% of the encapsulated RA over a period of 48 hours. However, RA concentrations above 0.1 mg/mL were found to be cytotoxic to fibroblast cultures in vitro because of the oily nature of RA. These formulations promoted wound healing when used to treat full thickness skin wounds (2 cm2) in Wister male rats. The wound contraction rates were significantly higher compared to a commercially available topical cream after a time period of 21 days. Histopathological analysis of the RA‐liposomal chitosan hydrogel group showed that the epidermis, dermis, and subcutaneous skin layers displayed an accelerated yet normal healing compared to control group. 相似文献
Summary: In this study, maleic anhydride (MA), and citric acid (CA) used as the processing additive and plasma treatment to improve the processing ability and mechanical strength of biodegradable starch/poly (vinyl alcohol) (PVA) blends were studied. The melt flow index (MFI) of starch/ glycerol/PVA (300g/60g/80g) blend was increased from 2.3g/10min to 32.7g/10min by adding 3g of MA and to 130 g/10min by adding MA and plasma treatment. The tensile strength of starch/glycerol/PVA blend increased from 3.48 to 6.21 MPa by adding 1.5g of MA and 1.5g of CA, while it increased to 6.26 MPa by plasma treatment. Esterification reaction which was evidenced by FTIR has been showed to improve the compatibility between starch and PVA when MA was dissolved into glycerol and glycerol grafted onto plasma pretreatment PVA. Thermogravimetric analysis (TGA) and scanning electron microscopy (SEM) imaging were used to study the morphology of extruded blends. 相似文献
Biodegradable poly(butylene succinate-co-lactate) (PBSL)/starch blends that contain various amounts of starch were prepared. In addition, luffa fiber (LF) and kenaf fiber (KF) were incorporated, individually, into PBSL/starch (70/30) blend to achieve biocomposites. The LF and KF were treated with NaOH(aq) prior to their addition to the blend. The Young's modulus and flexural modulus of PBSL increased with the addition of starch and increased further after the formation of the biocomposites. The highest Young's modulus increment, which was found in the KF-added system, was up to a 2.2-fold increase compared with neat PBSL. The tensile/flexural/impact strength of PBSL declined after the formation of the blends. With the further addition of LF/KF, the said properties leveled off. The blends exhibited higher complex viscosity and dynamic storage modulus in the melt state than the neat PBSL, and the values further increased in the biocomposites. The crystallization temperature of PBSL slightly decreased in the blends. By contrast, the biocomposites showed an increment in PBSL crystallization temperature, from 73.0 °C (PBSL) to 75.3 °C (KF-added composite), thereby confirming the surface nucleation effect of LF/KF. The blends showed a higher degree of water absorption than PBSL. The formation of biocomposites led to an even higher degree of water absorption. The current approach of including LF/KF in the PBSL/starch blend to enhance the rigidity and biodegradability was advantageous in expanding the applications of PBSL. 相似文献
The removal of methylene blue (MB) in water with the superabsorbent hydrogel (SH) formed by modified gum arabic, polyacrylate, and polyacrylamide was investigated. The SH exhibited excellent performance in MB absorption. The maximum absorption capacity was 48 mg of the dye per g of SH, representing 98% of the MB removed. Experimental parameters were used as follows: pH 8, hydrogel mass 50 mg, and initial concentration of MB 50 mg L(-1). In a procedure with an individual solution of orange II, an opposite effect related to the MB was observed: the hydrogel only absorbed water, resulting in an orange II-richer solution. The orange II concentration in solution increased about 50 times (relative to the initial concentration). In another experiment using an aqueous mixture of orange II and MB, the SH absorbed the MB exclusively. Compared to the MB, the orange II is separated from water by SH selectivity-absorption through an inverse process. This effect was attributed to the formation of a ionic complex between the imine groups of MB and the ionized carboxylic groups of SH. 相似文献
A synthetic toolbox for the introduction of aldehydo and hydrazido groups into the polysaccharides hyaluronic acid, alginate, dextran, pullulan, glycogen, and carboxymethyl cellulose and their use for hydrogel formation is reported. Upon mixing differently functionalized polysaccharides derived from the same natural precursor, hydrazone cross‐linking takes place, which results in formation of a hydrogel composed of one type of polysaccharide backbone. Likewise, hydrogels based on two different polysaccharide strands can be formed after mixing the corresponding aldehydo‐ and hydrazido‐modified polysaccharides. A second line of these studies paves the way to introduce a biomedically relevant ligand, namely, the adhesion factor cyclic RGD pentapeptide, by using an orthogonal click reaction. This set of modified polysaccharides served to create a library of hydrogels that differ in the combination of polysaccharide strands and the degree of cross‐linking. The different hydrogels were evaluated with respect to their rheological properties, their ability to absorb water, and their cytotoxicity towards human fibroblast cell cultures. None of the hydrogels studied were cytotoxic, and, hence, they are in principal biocompatible for applications in tissue engineering. 相似文献
This work evaluated such a cross-linked chitosan based controlled release device to be later used for sustained drug release. Cross linking was required to control chitosan swelling/deswelling rate. Hexamethylene 1,6-Bis (aminocarboxysulfonate), a bisulfite blocked diisocyanate obtained by the reaction of 1,6 Hexamethylene Diisocyanate and Sodium bisulfite, was used as cross linking agent. Two films formulations were tested: 30 and 50% cross-linked, and they were prepared by solvent evaporation technique. Chitosan cross-linked films were characterized for cross linkage by FTIR, for hydrophilicity by Contact Angle and for swelling behavior by Gravimetric method. Cross linking reaction was confirmed by FTIR. Moreover, cross linking increased the hydrophilic character of cross-linked films and suppressed swelling. However, 30% cross-linked film swollen less than the 50% one, while 50% cross-linked film swollen less than chitosan film itself. This behavior was attributed to the hydrophilic character of the cross linking agent and to the polymeric network formation by cross linking. 相似文献
A novel bead of modified starch for encapsulating 2,4-dichlorophenoxy acetate (2,4 DA) was made from natural rubber-graft-cassava starch (NS) and sodium alginate (SA) in a water-based system. The particle size and zeta potential of pristine NS, the NS/SA blend and the NS/SA blend containing 2,4 DA were evaluated. The swelling ratio in water of the beads was investigated and found to be enhanced as a function of the SA portion in the hydrogel due to an increase in the hydrophilic groups in the beads. In addition, the chemical interaction between 2,4 DA and the polymer matrix was investigated by FTIR and XRD. The results suggest that an NS/SA matrix is a good polymer membrane for encapsulating 2,4 DA in a water medium and the beads are also easily decomposed in the natural environment after use. 相似文献
The design of economical adsorbents to remove pollutants from contaminated water is attracting more attention. In this study, cellulose was successfully extracted from Robinia Pseudoacacia seed fibers and immobilized onto chitosan beads. The prepared spherical beads were then used for the biosorption of methylene blue dye from aqueous media. Samples were investigated using several analytical methods, namely FT-IR, XRD, EDX, SEM, and TGA analyses. The adsorption experiments showed that combining cellulose with chitosan improved the removal of methylene blue. The maximum uptake amount of methylene blue using cellulose–chitosan composite beads was 55 mg/g. However, it was about 35 mg/g at 20 °C for chitosan beads. The kinetic data complied strongly with the pseudo-second order equation, suggesting that the biosorption phenomenon has predominantly a chemical nature. Overall, the current study has shown a promising technique to design new adsorbents from abundant natural polymers for eliminating cationic dyes from water. 相似文献
The compositions and the multi phase structures of bio‐nanocomposite hydrogels made from silicate cross‐linked PEO and chitosan are related to some of their physical and biological properties. The gels are injectable and self‐healing because the cross‐linking is physical and reversible under deformation. The presence of chitosan aggregates affects the viscoelastic properties and reinforces the hydrogel network. The chitosan adds advantageous properties to the hydrogel such as enhanced cell spreading and adhesion. In vitro biocompatibility data indicate that NIH 3T3 fibroblasts grow and proliferate on the bio‐nanocomposite hydrogel as well as on hydrogel films.