Radiation effects on the thermal degradation of poly(vinyl chloride) and poly(vinyl alcohol)

Radiation effects on the formation of conjugated double bonds in the thermal degradation of poly(vinyl chloride) (PVC) and poly(vinyl alcohol) (PVA) were investigated. Thin films of PVC and PVA were either irradiated with γ-rays at ambient temperature (pre-irradiation) and then subjected to thermal treatment, or irradiated at elevated temperatures (in situ irradiation). An extensive enhancement of the thermal degradation was observed for the pre-irradiation of the PVC films, which was more effective than the effect of the in situ irradiation at the same absorption dose. For the PVA degradation, however, the effect of the in situ irradiation was larger than that of the pre-irradiation. The results were explained and related mechanisms were discussed based on radiation-induced chemical reactions and their individual contributions to the thermal degradation behaviors of the two polymers. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 3089–3095, 1998     

弹性体偶联剂结构对PVC/PPC性能的影响

NBR－PPC弹性体偶联剂能促进PPC（聚丙撑碳酸酯）与PVC（聚氯乙烯）之间的相容性，改善共混物的力学性能，并在共混体系中产生轻度交联。偶联剂组成在NBR／PPC比例为70／30，NBR（丁腈橡胶）含腈量为34％，BPO过氧化苯甲酸用量为2．5份时，共混物的综合力学性能最佳，但偶联剂预先硫化时间不宜过长．     

用DSC研究线形多嵌段聚氨酯与聚氯乙烯、氯化聚氯乙烯共混相容性

用示差扫描量热法（DSC）研究了线形多嵌段聚氨酯（PU）与聚氯乙烯（PVC）、氯化聚氯乙烯（CPVC）共混相容性，说明了PU／VC、PU／CPVC的相容是由于共混物中形成了新的氢键的缘故．聚酯型聚氨酯与PVC、CPVC的相容性要好子聚酸型聚氨酯，CPVC与PU的相容性又要好于PVC．聚氨酯中硬段的引入不利于PU／PVC、PU／CPVC的相容性．     

Thermal stability and thermal aging of poly(vinyl chloride)/MgAl layered double hydroxides composites

MgAl-LDH(layered double hydroxides) were prepared with CO(NH_2)_2, NH_4 Cl and NH_3·H_2O by the coprecipitation method, respectively. Corresponding composite membranes were prepared by the coating method. LDHs were characterized by WAXS, CO_2-TPD and SEM. The morphology of the PVC/LDHs composite membranes were characterized by means of SEM. The thermal stability of the membranes was analyzed by air aging box and TGA-FTIR. The SEM results show that nano-particles can be compatible with poly(vinyl chloride)(PVC) matrix homogeneously by the stirring-ultrasound blend method with two steps. Furthermore, the air aging box results proved that MgAl-CO(NH_2)_2-LDH has the best effect on thermal stability of PVC. TGA-FTIR results show that MgAl-CO(NH_2)_2-LDH could adsorb more HCl that resulted from the degradation of PVC and improve the pyrolysis temperature of the first degradation stage by 15 K compared with PVC.     

Effects of thermal stability on the crystallization behavior of poly(vinylidene chloride)

Thermal analysis based on TGA (thermal gravimetric analysis) and DSC (differential scanning calorimeter) shows no significant degradation for PVDC which has been annealed at 210°C for less than 2 min. And the following recrystallization behavior at lower temperature (120°C) is also independent of the thermal treatment and is not affected by the difference of molecular weight. The degradation which includes dehydrochlorination at lower temperature and intramolecular cyclization or intermolecular crosslinking of the polyenes at higher temperature starts when the melting time at 210°C is more than 2 min, which also causes weight loss and heat exchange in the TGA and DSC thermograms. The recrystallization behavior of the degraded PVDC (staying at 210°C for more than 2 min) shows a strong dependence on the molecular weight. The crystallinity is decreased with the melting time at 210°C due to the increase of the degree of crosslinking. However, the POM (polarized optical microscopy) pictures and IR spectra show a favorable nucleation effect is present due to the formation of trichlorobenzene from the cyclization of the polyenes as nuclei. The crystallinity of the PVDC recrystallized at 120°C after staying at 210°C for more than 2 min is actually dependent on the molecular weight, melting time at 210°C, and cyclized or crosslinking types of degradation. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3269–3276, 1999     

Thermal stability, smoke emission and mechanical properties of poly(vinyl chloride)/hydrotalcite nanocomposites

Poly(vinyl chloride)/hydrotalcite (PVC/HT) nanocomposites were prepared through vinyl chloride suspension polymerization in the presence of HT nanoparticles surface modified with alkyl phosphate (AP). The thermal stability, smoke emission and mechanical properties of PVC/HT nanocomposites were investigated. It was found that AP molecules were effectively absorbed by HT particles with no intercalation into the interlayer of HT. The dispersion morphologies of PVC/HT nanocomposites were observed by transmission electron microscopy showing that the majority of HT particles were dispersed in the PVC matrix in the nanoscale. The Congo Red measurement and thermogravimetric analysis showed that the thermal stability time, and the temperatures at 10% weight loss and at the maximum weight loss rate of PVC resins increased as the weight fraction of HT in the composite resins increased. The well-dispersed nano-sized HT showed an obvious smoke suppression effect on PVC. The maximum smoke density decreased about 1/3 and 1/2 when 2.5 wt% and 5.3 wt% nano-sized HT were incorporated into PVC, respectively. Furthermore, PVC/HT nanocomposites exhibited greater tensile strength and impact strength than the pristine PVC.     

Novel preparation of electrically conducting poly (vinyl chloride) by photo-dehydrochlorination from poly (vinyl chloride)/polypyrrole composite film

Polypyrrole (PPy) was deposited electrochemically on a platinum plate from a nitric acid solution of pyrrole. The PVC/PPy composite film was finally obtained by casting poly(vinyl chloride) (PVC) onto the PPy electrode from a tetrahydrofuran solution of PVC. The prepared composite film was irradiated at 90°C with a low-pressure mercury lamp in the stream of hydrogen gas saturated with steam, and the PVC film was dehydrochlorinated, leading to the formation of conjugated polyene. The electrical conductivity (σ) of the PVC film in the irradiated composite film was reveled: σ=2.51 × 10^?5S cm^?1. By iodine doping, σ was further enhanced up to 5.04 X 10^?3 S cm^?1. The tensile strength of the irradiated composite film became larger than that of the original PVC film; i.e., the stress at break was: 461 (composite film); 401 kg cm^?2 (PVC). These results were brought about by the doping of radical species to the conjugated polyene. The anion, NO^?₃, doped during the electrodeposition of PPy was photodecomposed to generate radical NO₂ and this species was doped to the polyene, resulting in the formation of electrically conductive PVC and mechanically improved composite film. © 1994 John Wiley & Sons, Inc.     

用FTIR研究线形多嵌段聚氨酯与聚氯乙烯、氯化聚氯乙烯共混相容性

用溶液法得到线形多嵌段聚氨酯（PU）与聚氯乙烯（PV）、氯化聚氯乙烯（CPVC）的共混物。用FTIR研究PU/PVC、PU／CPVC共混物的相容性，发现PVC、CPVC的加入破坏了PU中原来的氢键，并且PU中的炭基（C=0）与PVC、CPVC中的α－H形成了新的氢键，因而说明了PU／PVC、PU／CPVC共混物具有良好的相容性。     

Biodegradation of plasticized poly(vinyl chloride) containing cellulose

The plasticized poly(vinyl chloride) (PVC‐P) and its blend with cellulose (PVC‐P/cell) were prepared by means of extrusion. The samples were then biodegraded in forest soil as well as in soil enriched with cellulolytic microorganisms. Moreover, the samples were vaccinated with chosen species of fungi whose direct effect on polymer was then observed. The course of biodegradation was monitored in terms of, and by means of the following: weight loss, carbon dioxide evolved, attenuated total reflectance infrared (FTIR‐ATR) spectroscopy, gel permeation chromatography (GPC), as well as visual and microscopic observation (OM, SEM). The mechanical properties of samples were studied using the standard tensile tests. It was found that biodegradation in soil occurs in PVC‐P and this process is accelerated in the composition of PVC‐P with cellulose. The biodecomposition yield of PVC‐P/cellulose blends (calculated as relative percentage weight loss) is several dozen times higher than that of PVC‐P. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 903–919, 2007     

Mathematical models of the initial stage of the thermal degradation of poly(vinyl chloride). II. The thermal degradation of poly(vinyl chloride) with effective removal of HCl

The dehydrochlorination of different samples of PVC under vacuum with continuous removal of HCl by freezing, has been studied at 180–210°C. The comparison of the kinetic curves of the dehydrochlorination of various samples of PVC which were obtained by us and other investigators, with the theoretical curves for the thermal degradation of idealized PVC in the absence of HCl has been carried out. This had made it possible to evaluate the influence of unstable fragments present in the original polymer on the initial rate of PVC degradation quantitatively. It has been shown that the distinction between the stationary rates of the dehydrochlorination of various samples of PVC is determined by the difference of the values of the average length of dehydrochlorination chain, l_av. The most probable interval of the values of l_av has been ascertained to be 4–12. It is established that the most probable value of the constant of the rate of dehydrochlorination of normal links of PVC, k₀, is 2.1 × 10^?7?2.5 × 10^?7 s^?1 at 200°C. © 1993 John Wiley & Sons, Inc.     

Synthesis and characterization of novel poly(vinyl chloride)‐based grafts: Poly(vinyl chloride‐co‐2‐chloropropene) fitted with multiple high‐glass‐transition‐temperature polyolefin branches

The tertiary chlorine (Cl^t) content of vinyl chloride/2‐chloropropene copolymers [P(VC‐co‐2CP)] was determined by NMR spectroscopy. Copolymers containing 6.8–47.0 Cl^t's per P(VC‐co‐2CP) chain were used to initiate the cationic grafting of α‐methylstyrene, norbornadiene, indene, and norbornene with Et₂AlCl under various conditions. Grafting was demonstrated by selective solvent extraction, and the effect of the experimental conditions on the grafting efficiency was examined. Select rheological and thermal characteristics of P(VC‐co‐2CP) grafts, including the glass‐transition temperature, heat deflection temperature, and discoloration upon heating, were studied. P(VC‐co‐2CP) carrying 7–11 poly(α‐methylstyrene) or polynorbornadiene branches per chain raised the glass‐transition temperature to, or above, that of a blend control. P(VC‐co‐2CP)s fitted with polyindene or polynorbornene branches were less effective in raising the mechanical properties. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3644–3651, 2002     

Application of high resolution thermogravimetry to the study of thermal stability of poly(vinyl chloride) resins

The influence of microstructure on thermal degradation behaviour was studied in five samples of pure poly(vinyl chloride) (PVC) obtained at different polymerisation temperatures. Tacticity of the samples was characterized by Fourier transform infrared spectroscopy (FTIR), and their thermogravimetric behaviour was measured by high resolution (Hi-Res™) TGA. This technique is able to detect two independent weight loss steps in the dehydrochlorination. The relative contribution of these two steps responds to different syndiotacticity tendency of PVC samples, in accordance with FTIR results.     

Antimicrobial,mechanical, optical and thermal properties of PVC/ZnO‐EDTA nanocomposite films

Covalent surface functionalization of synthesized ZnO nanoparticles (NP)s with ethylenediaminetetraacetic acid (EDTA) was successfully carried out. Modified ZnO‐EDTA NPs as a viable and inexpensive filler were incorporated into poly(vinyl chloride) PVC matrix after their chemical modification to investigate the agglomeration behavior. All prepared materials including modified NPs and PVC/ZnO‐EDTA nanocomposites (NC)s were analyzed by Fourier transform infrared spectroscopy, ultraviolet–visible spectroscopy, thermogravimetric analysis, X‐ray diffraction, field emission scanning electron microscopy and transmission electron microscopy. Fabricated PVC/ZnO‐EDTA NCs were reported to have high transparency and improved mechanical properties compared with PVC. Modified ZnO and the fabricated NCs were shown to exhibit excellent antibacterial activity against two bacteria species: Escherichia coli and Staphylococcus aureus. The obtained NCs could be considered as self‐extinguishing materials on the basis of the LOI values. Copyright © 2016 John Wiley & Sons, Ltd.     

Terpyridine‐modified poly(vinyl chloride): Possibilities for supramolecular grafting and crosslinking

Commercially available poly(vinyl chloride) (PVC) was covalently modified with terpyridine supramolecular binding units in a two‐step reaction. First, PVC was modified with aromatic thiols to introduce OH functionalities into the polymer backbone, which were subsequently reacted with an isocyanate‐functionalized terpyridine binding unit. The resulting functionalized material contained metal‐ion binding sites, which could be used for grafting and crosslinking reactions. A grafting experiment was performed with a small organic terpyridine ligand. The complexation of the modified PVC with several transition‐metal ions was studied with ultraviolet–visible spectroscopy and gel permeation chromatography. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2964–2973, 2003     

Preparation and characterization of vinylidene chloride‐co‐vinyl chloride copolymer/fluorinated synthetic mica nanocomposites I thermal and mechanical properties studies

Poly(vinylidene chloride‐co‐vinylchloride)/organically modified fluorinated synthetic mica (MEE) (VDC‐VC/MEE) nanocomposites were prepared by melt blending of VDC‐VC copolymer with MEE, in the presence of dioctyl phthalate (DOP) which acted as a plasticizer and a cointercalating agent. The nanostructure, thermal, and dynamic mechanical properties of the VDC‐VC/MEE nanocomposites were studied by wide angle X‐ray diffractometer (WAXD), scanning electron microscope (SEM), transmission electron microscope (TEM), thermogravimetric analyzer (TGA), and dynamic mechanical analyzer (DMA). It was found that partially intercalated and partially exfoliated structures coexisted in VDC‐VC/MEE nanocomposities. Below 8 wt % MEE content, the intercalation effect of nanocomposites decreased with increasing the MEE content. Under a nitrogen atmosphere, VDC‐VC/MEE nanocomposites exhibited a single step thermal degradation behavior. The nanostructure of VDC‐VC/MEE can effectively prevent volatile gases from being released, and thus enhances its thermal stability. The thermal stability of VDC‐VC/MEE nanocomposites is strongly related to the morphology of nanocomposites and the degraded composites structure. DMA revealed a significant improvement in the storage modulus within the testing temperature range. The increase in storage modulus depends on the MEE content, which is attributed to the dispersed phase morphology. The glass transition temperature of VDC‐VC/MEE nanocomposites is affected by the chain mobility in the nanocomposites rather than the aggregative morphology. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1214–1225, 2008     

Influence of imide functionalized organo‐modified Mg‐Al layered double hydroxide on the thermal and mechanical properties of new aliphatic‐aromatic poly (amide‐imide)

A new dicarboxylic acid modified Mg‐Al LDH (DLDH) containing imide groups was prepared and its effects on the thermal and mechanical properties of the new synthesized aliphatic‐aromatic poly (amide‐imide) (PAI) were investigated via preparation of PAI/nanocomposite films by solution casting method. The results of X‐ray diffraction (XRD), field emission‐scanning electron microscopy (FE‐SEM) and transmission electron microscopy (TEM) showed a uniform dispersion for LDH layers into the PAI matrix. For comparison, the effects of polyacrylic acid‐co‐poly‐2‐acrylamido‐ 2‐methylpropanesulfonic acid (PAMPS‐co‐PAA) modified Mg‐Al LDH (ALDH) on the PAI properties were also studied. The thermogravimetric analysis (TGA) results exhibited that the temperature at 5 mass% loss (T₅) increased from 277 °C to 310 °C for nanocomposite containing 2 mass% of DLDH, while T₅ for nanocomposite containing 2 mass% of ALDH increased to 320 °C, along with the more enhancement of char residue compared to the neat PAI. According to the tensile test results, with 5 mass% DLDH loading in the PAI matrix, the tensile strength increased from 51.6 to 70.8 MPa along with an increase in Young's modulus. Also the Young's modulus of PAI nanocomposite containing 5 mass% ALDH reduced from 1.95 to 0.81 GPa.     

Oxygen barrier,free volume,and blending properties of polyamide 12/poly (vinyl alcohol) blends

Oxygen permeation rates, average volumes of free‐volume‐cavities (V_f), and fractional free volumes (F_v) of polyamide 12 (PA12)/poly(vinyl alcohol) (PVA) (ie, PA12_xPVA⁰⁵_y, PA12_xPVA⁰⁸_y, and PA12_xPVA¹⁴_y) blend films with varying PVA degrees of polymerization reduced to a minimum value when their PVA contents reached a corresponding optimal value, respectively. The minimum oxygen permeation rates, V_f, and F_v values obtained for the optimal PA12_xPVA^z_y blown films were reduced considerably with decreasing PVA degrees of polymerization. Experimental findings from dynamic mechanical analysis, differential scanning calorimetry, wide angle X‐ray diffraction, and Fourier transform infrared spectroscopy of the PA12_xPVA^z_y blend series suggest that PA12 and PVA in PA12_xPVA^z_y are miscible to some extent at the molecular level when their PVA contents are near and less than the corresponding critical values. The considerably enhanced oxygen barrier properties of the PA12_xPVA^z_y blend films with optimized compositions are attributed to the significantly reduced local free volume characteristics.     

Interfacial properties and thermal stability of modified poly(m‐phenylene isophthalamide) thin films

Poly(m‐phenylene isophthalamide) (PMIA) is a resistant to high temperatures and chemically stable engineering material. The application as coatings and membranes, however, is limited by its poor interaction with other materials. In this report, we describe the molecular modification of PMIA through reaction with dimsyl sodium and 2‐iodine‐1‐ethanol. The substitution of 58% of amide hydrogen by ethanol (etOH) groups produces a material (MPMIA) able to develop regularly structured films on silicon substrate. The morphology of the films is dependent on the ionic strength of the precursory solution. MPMIA starts a degradation process by losing the etOH group. MPMIA has a better affinity with poly(p‐cresolformaldehyde) than with a pristine one, increasing the range of composition in which thermal stability and miscibility are observed. Thin films of these blends have different morphologies that vary from nanometric porous to two‐phase microstructured grains, according to the composition. Copyright © 2012 John Wiley & Sons, Ltd.     

Influence of physical-chemical interactions on the thermal stability and surface properties of poly(vinyl chloride)-b-poly(hydroxypropyl acrylate)-b-poly(vinyl chloride) block copolymers

The synthesis of poly(vinyl chloride) (PVC) homopolymers and poly(vinyl chloride)-b-poly(hydroxypropyl acrylate)-b-poly(vinyl chloride) (PVC-b-PHPA-b-PVC) block copolymers via a single electron - degenerative transfer mediated living radical polymerisation was carried out on a pilot scale in industrial facilities. The thermal stability of the products was assessed conductimetrically. The block copolymers, that contained a low content of PHPA (below 12 wt.%), showed thermal stability that was approximately three times greater than that of conventional PVC. Inverse gas chromatography study of the copolymers surface showed that there was a decrease in the dispersive component and greater Lewis acidity and basicity constants were observed relative to those of PVC. The thermal stabilisation of PVC when in the presence of PHPA is explained by the interactions between its functional groups and the structures formed during the thermal degradation. The thermal stability and the surface properties of PVC-b-PHPA-b-PVC were strongly dependent on the molecular weight of the block copolymer. Lewis acid-base interaction parameters were determined and are interpreted as evidence of the PVC-b-PHPA-b-PVC compatibilising function in PVC-wood flour composites.     

共混方法对聚氯乙烯/聚丙撑碳酸酯相容性影响

本文分别用溶液法和熔融法制得聚氯乙烯（PVC）与聚丙撑碳酸酯（PPC）共混试样，用DSC证明PVC／PPC共混物不相容，但它们不相容的程度受分子量、共混比例等因素的影响，并根据玻璃化转变温度（Tg）计算出溶液共混试样PPC富相中PVC的重量百分含量。NBR／PPC弹性体作偶联剂对PVC／PPC共混体系具有较好的增容作用，共混物中PPC的用量及分子量对共混体系性能有一定的影响。