Thermal properties in cured natural rubber/styrene butadiene rubber blends

Blends of natural rubber (NR) and styrene butadiene rubber (SBR) were prepared with sulfur and n-t-butyl-2-benzothiazole sulfonamide (TBBS) as accelerator, varying the amount of each polymer in the blend. Samples were analysed by rheometer curing at 433 K until their maximum torque was reached. The miscibility among the constituent polymers of the cured compounds was studied in a broad range of temperatures by means of differential scanning calorimetry, analyzing the glass transition temperatures of the samples. The specific heat capacity of the compounds was also determined. Thermal diffusivity of the samples was measured in the temperature range from 130 to 400 K with a new device that performs measurements in vacuum. The thermal results are explained on the basis of the structure formed during the vulcanization of the samples considering the variation of the crosslink density of each phase. Finally, a serial thermal conduction model that takes into account the contribution of each phase to the thermal diffusivity was used to fit the experimental results.     

A SAXS and swelling study of cured natural rubber/styrene–butadiene rubber blends

A small‐angle X‐ray scattering (SAXS) and swelling study of natural rubber and styrene–butadiene rubber blends (NR/SBR) is presented. To this aim, specimens of NR and SBR and blends with 75/25, 50/50, and 25/75 NR/SBR ratios (in phr) were prepared at a cure temperature of 433 K and the optimum cure time (t₁₀₀). This time was obtained from rheometer torque curves. The system of cure used in the samples was sulfur/n‐t‐butyl‐2‐benzothiazole sulfenamide. From swelling tests of the cured samples, information about the molecular weight of the network chain between chemical crosslinks was obtained. For all cured compounds, in the Lorentz plots built from SAXS scattering curves, a maximum of the scattering vector q around 0.14 Å^?1 was observed. However, the q position shows a linear‐like shift toward lower values when the SBR content in the SBR/NR blend increases. In pure NR or SBR the q values show a different tendency. The results obtained are discussed in terms of the existence of different levels of vulcanization for each single phase forming the blend and the existence of a third level of vulcanization located in the interfacial NR/SBR layer. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2320–2327, 2009     

Effect of antioxidants on aging of the chloroprene rubber/butadiene rubber (CR/BR) blends

Thermal degradation of blends containing chloroprene rubber (CR) and butadiene rubber (BR) cross-linked with copper(II) oxide (CuO) with the addition of anti-aging substance ((N-(1.3-dimethylbutyl)-N-phenyl-p-phenylenediamine (6PPD), polymerized 2.2.4-trimethyl-1.2-dihydroquinoline (TMQ), or 2-mercaptobenzimidazole (MBI)) under high temperature was investigated using a Fourier Transform Infrared spectroscopy (FTIR) spectroscopy and color measurement. Additionally, changes in mechanical properties (such as tensile strength, elongation at break, hardness, tear resistance) causes by aging factors have also been investigated. The results indicated that the 6PPD and the MBI provided better protection of the CR/BR/CuO vulcanizates against degradation at elevated temperature than the TMQ. As a result of thermo-oxidative aging, in an infrared spectrum, a peak assigned to stretching vibration of carbonyl groups was observed. Differences in protection against thermo-oxidative aging by the anti-aging substance are caused by their different structure, consequently, by the differences in their protection mechanism.     

Morphology and mechanical and viscoelastic properties of natural rubber and styrene butadiene rubber latex blends

The morphology and mechanical and viscoelastic properties of a series of blends of natural rubber (NR) and styrene butadiene rubber (SBR) latex blends were studied in the uncrosslinked and crosslinked state. The morphology of the NR/SBR blends was analyzed using a scanning electron microscope. The morphology of the blends indicated a two phase structure in which SBR is dispersed as domains in the continuous NR matrix when its content is less than 50%. A cocontinuous morphology was obtained at a 50/50 NR/SBR ratio and phase inversion was seen beyond 50% SBR when NR formed the dispersed phase. The mechanical properties of the blends were studied with special reference to the effect of the blend ratio, surface active agents, vulcanizing system, and time for prevulcanization. As the NR content and time of prevulcanization increased, the mechanical properties such as the tensile strength, modulus, elongation at break, and hardness increased. This was due to the increased degree of crosslinking that leads to the strengthening of the 3‐dimensional network. In most cases the tear strength values increased as the prevulcanization time increased. The mechanical data were compared with theoretical predictions. The effects of the blend ratio and prevulcanization on the dynamic mechanical properties of the blends were investigated at different temperatures and frequencies. All the blends showed two distinct glass‐transition temperatures, indicating that the system is immiscible. It was also found that the glass‐transition temperatures of vulcanized blends are higher than those of unvulcanized blends. The time–temperature superposition and Cole–Cole analysis were made to understand the phase behavior of the blends. The tensile and tear fracture surfaces were examined by a scanning electron microscope to gain an insight into the failure mechanism. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2189–2211, 2000     

Maleic-anhydride grafted EPM as compatibilising agent in NR/BR/EPDM blends

Incorporation of approximately 30 phr Ethylene-Propylene-Diene rubber (EPDM) into natural rubber (NR)/butadiene rubber (BR) is a means to achieve non-staining ozone resistance for tire sidewall applications. However, due to incompatibility of the elastomers and heterogeneous filler distribution in each of the rubber phases, the mechanical properties deteriorate. In the present work, maleic-anhydride modified EPM (MAH-EPM) is added as a compatibilising agent between NR/BR and EPDM. The addition of 5 phr of MAH-EPM results in significantly improved tensile and tear strength when compared to a straight NR/BR/EPDM blend. These improvements can mainly be attributed to a compatibilising effect of MAH-EPM, resulting in a more homogeneous phase distribution, but in particular a much better homogeneous carbon black distribution over the different rubber phases. In addition, ionic crosslinks are introduced into the blends by interaction of MAH-EPM with zinc oxide.     

Anisotropic studies of multi-wall carbon nanotube (MWCNT)-filled natural rubber (NR) and nitrile rubber (NBR) blends

50/50 NR/NBR blends with various MWCNT loadings were prepared by mixing with MWCNT/NR masterbatches on a two-roll mill and sheeted off at the smallest nip gap. Then, the effect of milling direction, machine direction (MD) and transverse direction (TD), on the mechanical and electrical properties of the blends was elucidated. Dichroic ratio and SEM results confirmed that most of the MWCNTs were aligned along MD when MWCNT was less than 4 phr, and the number of agglomerates increased when MWCNT was more than 4 phr. Additionally, anisotropic properties were clearly observed when 4 phr MWCNT was loaded. At 4 phr MWCNT, 100% modulus and tensile strength in the MD were about 1.5 and 1.3 times higher than those in the TD, respectively. Moreover, electrical conductivity in the MD was superior to that in the TD by about 3 orders of magnitude. Results from dynamic mechanical tests also showed that the maximum tan δ in the MD sample was lower than that in the corresponding TD sample. In addition, the storage modulus at 30 °C for the MD sample containing 4 phr MWCNT was 1.15 higher than that of the corresponding TD sample. This stronger reinforcement efficiency resulted from the combination of the greater alignment and dispersion of most MWCNTs in the MD sample.     

Dichlorocarbene modified butadiene rubber (DCBR): Preparation,kinetic study,and its properties in natural rubber/DCBR blend vulcanizates

Dichlorocarbene modified butadiene rubber (DCBR) was prepared via the addition of the dichlorocarbene group in the presence of 2 phase transfer agents (cetyltrimethylammonium bromide and tetraethylammonium chloride). The effects of the reaction temperature and time, amount of dichlorocarbene precursor, and the type and amount of phase transfer agent on the chlorine content were investigated. The highest chlorine content (30%) in DCBR was obtained using 0.062 mol chloroform and 0.003 mol cetyltrimethylammonium bromide at room temperature for 19 hours although 27.9% was obtained after 12 hours. The kinetics of this dichlorocarbene modification was best described by the pseudo–first order rate law with 2 rate constants. For practical applications, the DCBR with chlorine contents of 10%, 20%, or 30% were blended with natural rubber (NR) and then vulcanized using the sulfur‐curing system. Although the polarity of DCBR was increased, a good compatibility between NR and DCBR still existed, resulting in improved mechanical properties. The oil resistance, flame retardant, and ozone resistance properties of the NR/DCBR blend vulcanizates were enhanced compared to those of a NR/butadiene rubber blend vulcanizate, which was related to the amount of chlorine incorporated into the DCBR.     

Compatibilized natural rubber/recycled ethylene-propylene-diene rubber blends by biocompatibilizer

Biocompatibilizer-based refined, bleached, deodorized palm stearin was successfully used as compatibilizer for natural rubber/recycled ethylene–propylene–diene rubber (NR/R-EPDM) blends. It seems effective in improving the state of cure, tensile properties, as well as the swelling resistance and morphology of the blends, indicating an improvement in compatibility between the NR matrix and R-EPDM rendered by biocompatibilizer. This was clearly verified by the dynamic mechanical properties of the blends. The dynamic responses obtained were clearly corresponding to the swelling result. It proves that the cross-link density plays a major role in the changes of storage modulus and degree of entanglement.     

Effects of epoxidized natural rubber as a compatibilizer in melt compounded natural rubber-organoclay nanocomposites

Nanocomposites containing natural rubber (NR) as matrix, epoxidized natural rubber (ENR) as compatibilizer and organophilic layered clay (organoclay) as filler were produced in an internal mixer and cured using a conventional sulphuric system. The effects of ENR with 25 (ENR 25) and 50 mol% epoxidation (ENR 50), respectively, were compared at 5 and 10 parts per hundred rubber (phr) concentrations. The organoclay content was fixed at 2 phr. Cure characteristics, clay dispersion, (thermo)mechanical properties of the nanocomposites were determined and discussed. Incorporation of ENR and organoclay strongly affected the parameters which could be derived from Monsanto MDR measurements. Faster cure and increased crosslink density were attributed to changes in the activation/crosslinking pathway which was, however, not studied in detail. The organoclay was mostly intercalated according to X-ray diffraction (XRD) and transmission electron microscopic (TEM) results. The best clay dispersion was achieved by adding ENR 50. This was reflected in the stiffness of the nanocomposites derived from both dynamic mechanical thermal analysis (DMTA) and tensile tests. The tensile and tear strengths of the ENR 50 containing nanocomposites were also superior to the ENR 25 compatibilized and uncompatibilized stocks.     

TG-MS analysis of nitrile butadiene rubber blends (NBR/PVC)

Blends of nitrile butadiene rubber (NBR) with polyvinyl chloride (PVC) are widely used in products such as hoses and seals. As part of a project that uses NBR/PVC blends for manufacturing forest fire hoses, blends of NBR/PVC with various inorganic fillers, such as Mg(OH)₂, china clay (organic modified kaolin) and nano clay (organic modified bentonite) were studied by TG-MS. No significant changes were observed to the type of the polymers’ decomposition products, compared to that of NBR/PVC blend without additives. The most remarkable change was the absence of HCl from decomposition products in the presence of the Mg(OH)₂ additive.     

Influence of fluorine-containing lubricant on properties of NR/BR rubber

K95 experimental lubricant being a product of fluorine reaction with a blend of mutually soluble poly(fluorine alcohols) and poly(fluorine esters) with molecular weight 240-900 g/mol was studied as an additive for rubber compounds based on blend of NR and BR. It was thermally stable till 270-300 °C. For comparison, it was tested simultaneously with homogenizing agent, Struktol MS40. Lubricant K95 added in a quantity of 0.5 wt% reduced the viscosity of rubber compound; it also improved compound flow in the mold. Mechanical properties of cured rubber not decrease while resistance to abrasion and fatigue increased. K95 participated in forming strong physical junctions (lower molecular weight between junctions of thermally stable network) while Struktol MS40 reduced the networking degree of rubber. As a result, it acts a multifunctional additive for NR/BR rubber.     

Radiation effect on properties of carbon black filled NBR/EPDM rubber blends

Rubber blend of acrylonitrile butadiene rubber (NBR) and ethylene-propylene diene monomer (EPDM) rubber (50/50) has been loaded with increasing contents, up to 100 phr, of reinforcing filler, namely, high abrasion furnace (HAF) carbon black. Prepared composites have been subjected to gamma radiation doses up to 250 kGy to induce radiation vulcanization under atmospheric conditions. Mechanical properties, namely, tensile strength (TS), tensile modulus at 100% elongation (M₁₀₀), and hardness have been followed up as a function of irradiation dose and degree of loading with filler. On the other hand, variation of the swelling number as a physical property, as a function of same parameters, however, in car oil as well as brake oil has been undertaken. In addition, the electrical properties of prepared composites, namely, their electrical conductivity, were also evaluated. The thermal behavior of the prepared composites was also investigated. The results obtained indicate that improvement has been attained in different properties of loaded NBR/EPDM composites with respect to unloaded ones.     

Degradation of polychloroprene/natural rubber (PCP/NR) blends by photo-Fenton process

The effect of light and FeCl₃·6H₂O on polychloroprene (PCP)/natural rubber (NR) blends in toluene solution were investigated to demonstrate the influence of each polymer on the degradation process. The contributions of total polymer concentration (C_p), temperature (T) and polychromatic light exposure (L) on the degradation process were investigated through a 2³ factorial design approach. Degradation kinetics was examined by solution viscosity time data. FTIR spectroscopy and TGA were used to characterize the degradation. The exposure of the PCP/NR blend solution containing FeCl₃·6H₂O to light induces degradation in the polymers. A decrease of up to 70% in solution efflux time at constant temperature and without aggregation or phase separation was observed. PCP degradation by-products amplify the degradation of NR, as evidenced by the decrease in the PCP/NR 1:99 (w/w) solution efflux time, which was larger than that of the pure NR solution. The film cast from the solution exposed to light was thermally less stable than the one which was cast without FeCl₃·6H₂O.     

Compatibilization efficiency of styrene–butadiene multiblock copolymers in PS/PP blends

The compatibilizing effect of di‐, tri‐, penta‐, and heptablock (two types) copolymers with styrene and butadiene blocks was studied in polystyrene/polypropylene (PS/PP) 4/1 blends. The structure of PS/PP blends with the addition of 5 or 10 wt % of a block copolymer (BC) was determined on several scale levels by means of transmission electron microscopy (TEM) and small‐angle X‐ray scattering (SAXS). The results of the structure analysis were correlated with measured stress‐transfer properties: elongation at break, impact, and tensile strength. Despite the fact that the molar mass of the PS blocks in all the BCs used was about 10,000, that is, below the critical value M^* (～18,000) necessary for the formation of entanglements of PS chains, all the BCs used were found to be good compatibilizers. According to TEM, a certain amount of a BC is localized at the interface in all the analyzed samples, and this results in a finer dispersion of the PP particles in the PS matrix, the effect being more pronounced with S‐B‐S triblock and S‐B‐S‐B‐S pentablock copolymers. The addition of these two BCs to the PS/PP blend also has the most pronounced effect on the improvement of mechanical properties of these blends. Hence, these two BCs can be assumed to be better compatibilizers for the PS/PP (4/1) blend than the S‐B diblock as well as both S‐B‐S‐B‐S‐B‐S and B‐S‐B‐S‐B‐S‐B heptablock copolymers. In both types of PS/PP/BC blends (5 or 10 wt % BC), the BC added was distributed between both the PS/PP interface and the PS phase, and, according to SAXS, it maintained a more or less ordered supermolecular structure of neat BCs. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 931–942, 2001     

Thermoplastic elastomer based on high‐density polyethylene/natural rubber blends: rheological,thermal, and morphological properties

Thermoplastic elastomer (TPE) comprising air‐dried sheet or natural rubber (ADS or NR) and high‐density polyethylene (HDPE) was prepared by a simple blending technique. NR and HDPE were mixed with each type of phenolic compatibilizer (HRJ‐10518 or SP‐1045) or liquid natural rubber (LNR) at 180°C in an internal mixer. The mixing torque, shear stress, and shear viscosity of the blends increased with increasing amounts of NR. Positive deviation blend (PDB) for the blends containing active hydroxyl methyl phenolic resin in HRJ‐10518 or dimethyl phenolic resin in SP‐1045 was obtained. PDB was not observed for the blends without the compatibilizers or with LNR. The blends with HRJ‐10518 or SP‐1045 were compatible or partially compatible while the LNR blends were incompatible. In the phenolic compatibilized blends, NR dispersed in the HDPE matrix was found in the NR/HDPE blends of 20/80, 40/60, and 50/50 ratios. HDPE dispersed in NR matrix was obtained in the NR/HDPE blend of 80/20 ratio, and the co‐continuous phase was accomplished in the NR/HDPE blend of 60/40 ratio. The NR/HDPE blend at 60/40 ratio compatibilized with HRJ‐10518 and fabricated by a simple plastic injection molding machine exhibited higher ultimate tensile strength and elongation at break (EB). Incorporation of parafinic oil caused a decreasing tendency in tensile strength with increases in EB. The TPNRs exhibited high elastomeric nature with low‐tension set. Copyright © 2007 John Wiley & Sons, Ltd.     

Thermal and rheological properties of miscible polyethersulfone/polyimide blends

Blends of an aromatic polyethersulfone (commercial name Victrex) and a polyimide (commercial name Matrimid 5218), the condensation product of 3,3′,4,4′-benzophenone tetracarboxylic dianhydride and 5(6)-amino-1-(4′-aminophenyl)-1,3,3′-trimethylindane, were studied by differential scanning calorimetry, dynamic mechanical analysis, and rheological techniques. The blends appeared to be miscible over the whole range of compositions when cast as films or precipitated from solution in a number of solvents. After annealing above the apparent phase boundary, located above T_g, the blends were irreversibly phase separated indicating that the observed phase boundary does not represent a true state of equilibrium. Only a narrow “processing window” was found for blends containing up to 20 wt % polyimide. Rheological measurements in this range of compositions indicated that blending polyethersulfone with polyimide increases the complex viscosity and the elastic modulus of the blends. For blends containing more than 10 wt % polyimide, abrupt changes in the rheological properties were observed at temperatures above the phase boundary. These changes may be consistent with the formation of a network structure (due to phase separation and/or crosslinking). Blends containing less than 10 wt % polyimide exhibited stable rheological properties after heating at 320°C for 20 min, indicating the existence of thermodynamic equilibrium.     

Natural rubber/styrene-butadiene rubber blends prepared by solution mixing: Influence of vulcanization temperature using a Semi-EV sulfur curing system on the microstructural properties

Blends of natural rubber (NR) and styrene-butadiene rubber (SBR) were prepared by solution mixing and vulcanized with sulfur and accelerator in a Semi-EV system at 433 K and 443 K in order to study the vulcanization kinetic and the influence of vulcanization temperature on final structure of the blends. The vulcanization kinetic studied through the variation in rheometer curves was analyzed using the Ding and Leonov model, which takes into account the reversion effect during the cure process. The average free nanohole volume and the fractional free volume of samples with different NR/SBR ratio were estimated using positron annihilation lifetime spectroscopy (PALS). Also, the crosslink density was determined by means of swelling tests in a solvent. For all the compounds, a correlation between the free nanohole volume and the delta torque obtained from the respective rheometer curves was established.     

Effect of carbon nanofibers on mechanical and electrical behaviors of acrylonitrile‐butadiene rubber composites

Recently, carbon nanofibers have become an innovative reinforcing filler that has drawn increased attention from researchers. In this work, the reinforcement of acrylonitrile butadiene rubber (NBR) with carbon nanofibers (CNFs) was studied to determine the potential of carbon nanofibers as reinforcing filler in rubber technology. Furthermore, the performance of NBR compounds filled with carbon nanofibers was compared with the composites containing carbon black characterized by spherical particle type. Filler dispersion in elastomer matrix plays an essential role in polymer reinforcement, so we also analyzed the influence of dispersing agents on the performance of NBR composites. We applied several types of dispersing agents: anionic, cationic, nonionic, and ionic liquids. The fillers were characterized by dibutylphtalate absorption analysis, aggregate size, and rheological properties of filler suspensions. The vulcanization kinetics of rubber compounds, crosslink density, mechanical properties, hysteresis, and conductive properties of vulcanizates were also investigated. Moreover, scanning electron microscopy images were used to determine the filler dispersion in the elastomer matrix. The incorporation of the carbon nanofibers has a superior influence on the tensile strength of NBR compared with the samples containing carbon black. It was observed that addition of studied dispersing agents affected the performance of NBR/CNF and NBR/carbon black materials. Especially, the application of nonylphenyl poly(ethylene glycol) ether and 1‐butyl‐3‐methylimidazolium tetrafluoroborate contributed to enhanced mechanical properties and electrical conductivity of NBR/CNF composites.     

Ionic liquid functionalized graphene oxide for enhancement of styrene‐butadiene rubber nanocomposites

Ionic liquid 1‐allyl‐3‐methyl‐imidazolium chloride (AMICl) is used to fine‐tune the surface properties of graphene oxide (GO) sheets for fabricating ionic liquid functionalized GO (GO‐IL)/styrene‐butadiene rubber (SBR) nanocomposites. The morphology and structure of GO‐IL are characterized using atomic force microscope, X‐ray diffraction, differential scanning calorimetry, X‐ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, UV‐vis spectra and Raman spectra. The interaction between GO and AMICl molecules as well as the effects of GO‐IL on the mechanical properties, thermal conductivity and solvent resistance of SBR are thoroughly studied. It is found that AMICl molecules can interact with GO via the combination of hydrogen bond and cation–π interaction. GO‐IL can be well‐dispersed in the SBR matrix, as confirmed by X‐ray diffraction and scanning electron microscope. Therefore, the SBR nanocomposites incorporating GO‐IL exhibit greatly enhanced performance. The tensile strength, tear strength, thermal conductivity and solvent resistance of GO‐IL/SBR nanocomposite with 5 parts per hundred rubber GO‐IL are increased by 505, 362, 34 and 31%, respectively, compared with neat SBR. This method provides a new insight into the fabrication of multifunctional GO‐based rubber composites. Copyright © 2016 John Wiley & Sons, Ltd.     

Dynamic mechanical behavior of acrylonitrile butadiene rubber/poly(ethylene‐co‐vinyl acetate) blends

The dynamic mechanical behavior of uncrosslinked (thermoplastic) and crosslinked (thermosetting) acrylonitrile butadiene rubber/poly(ethylene‐co‐vinyl acetate) (NBR/EVA) blends was studied with reference to the effect of blend ratio, crosslinking systems, frequency, and temperature. Different crosslinked systems were prepared using peroxide (DCP), sulfur, and mixed crosslink systems. The glass‐transition behavior of the blends was affected by the blend ratio, the nature of crosslinking, and frequency. sThe damping properties of the blends increased with NBR content. The variations in tan δ_max were in accordance with morphology changes in the blends. From tan δ values of peroxide‐cured NBR, EVA, and blends the crosslinking effect of DCP was more predominant in NBR. The morphology of the uncrosslinked blends was examined using scanning electron and optical microscopes. Cocontinuous morphology was observed between 40 and 60 wt % of NBR. The particle size distribution curve of the blends was also drawn. The Arrhenius relationship was used to calculate the activation energy for the glass transition of the blends, and it decreased with an increase in the NBR content. Various theoretical models were used to predict the modulus of the blends. From wide‐angle X‐ray scattering studies, the degree of crystallinity of the blends decreased with an increasing NBR content. The thermal behavior of the uncrosslinked and crosslinked systems of NBR/EVA blends was analyzed using a differential scanning calorimeter. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1556–1570, 2002