Polymethylmethacrylate derivatives Eudragit E100 and L100: Interactions and complexation with surfactants

Precipitation or coprecipitation of polyelectrolytes has been largely investigated. However, the precipitation of polyelectrolytes via addition of charged and non‐charged surfactants has not been systematically studied and reported. Consequently, the aim of this work is to investigate the effect of different surfactants (anionic, cationic, non‐charged and zwitterionic) on the precipitation of cationic and anionic polymethylmethacrylate polymers (Eudragit). The surfactants effect has been investigated as a function of their concentration. Special attention has been dedicated to the CMC range and to the colloidal characterization of the formed dispersions. Moreover, the effect of salt (NaCl) and pH was also addressed. It is pointed out that non‐ionic and zwitterionic surfactants do not interact with charged Eudragit E100 and L100. For oppositely charged Eudragit E100/SDS and Eudragit L100/CTAB, precipitation occurs, and the obtained dispersions have been characterized in terms of particle size distribution and zeta potential. It was established that the binding of SDS molecules to Eudragit E100 polymer chains is made through the negative charges of the surfactant heads under the CMC value whereas binding of CTAB to Eudragit L100 chains is made at a CTAB concentration 5 times above its CMC. For Eudragit E100/SDS system, a more acidic medium induces aggregation. A same result was observed for the Eudragit L100/CTAB at a more basic pH. Moreover, it was observed that increasing salt concentration (higher than 100 mM) led to aggregation as generally observed for polycations/anionic surfactant systems.     

pH‐Sensitive methacrylic acid–methyl methacrylate copolymer Eudragit L100 and dimethylaminoethyl methacrylate,butyl methacrylate,and methyl methacrylate tri‐copolymer Eudragit E100

Poly (methyl methacrylate) derivatives such as Eudragit are largely used for drug encapsulation and in controlled oral drug delivery. With special focusing on those applications, solubilization and precipitation conditions of two pH‐sensitive Eudragit polymers, namely, L100 and E100, were investigated via systematic studies. Effects of various physicochemical parameters such as pH, polymer concentration, salinity, buffer concentration, and incubation time on the solubilization and precipitation of these polymers were investigated. In addition, pH titration of both polymers was reported. Considering both macroscopic and quantitative aspects such as the final mean particle size, size distribution, morphology, and the zeta potential, it was established that the different precited parameters could not be dissociated and exert a synergic action on the solubilization and precipitation of both polymers. Titration curves revealed two equivalences that helped estimating carboxylic content of Eudragit L100 (6 mmol/g) and ammonium content of Eudragit E100 (4 mmol/g). In this study, the solubilization and the precipitation domains were for the first time clearly established by considering the above‐mentioned parameters. Moreover, it was found that Eudragit L100 and E100 cannot be considered as classic polyelectrolytes; in fact, solubilization and precipitation domains were not affected by ionic strength.     

Nonviral gene delivery using poly‐D/L aspartate‐diethylenetriamine cationic polymers and polyethylene glycol: A two‐step approach

Cationic polymers have received much attention as promising nonviral vectors for gene transfer. However, development of polymers with low cell toxicities and high transfection efficiencies continue to be a significant problem and a major hurdle to their success. Poly‐D /L aspartate‐diethylenetriamine poly(D /L Asp‐DET) polymers were synthesized and evaluated as nonviral gene delivery agents. Poly(D /L Asp‐DET) polymers display endosome buffering capacity. The polymers condense plasmid DNA above N:P ratios of 1 and form polyplex particles of ～50–100 nm, with zeta potentials between neutral and +40 mV. Transmission electron microscopy shows the polyplexes to be uniform in size and shape. Polyplexes maintain the structural integrity of DNA following incubation in nucleases and also show high transfection efficiencies with minimal toxicity in both HCT‐116 and PC‐3 cell culture. However, it is found that these poly(D /L Asp‐DET)/DNA polyplexes immediately aggregate in salt and serum conditions, making them unsuitable for use in vivo. Therefore, the polyplexes were further modified by covalent addition of polyethylene glycol (PEG). Introduction of this second step produces PEG‐polyplexes of uniform size (below 100 nm), with neutral zeta potentials that are also stable in both salt and serum conditions. These results suggest poly(D /L Asp‐DET) cationic polymers as potentially safe and efficient nonviral gene delivery agents. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Polyplex Particles Based on Comb‐Like Polyethylenimine/Poly(2‐ethyl‐2‐oxazoline) Copolymers: Relating Biological Performance with Morphology and Structure

The present contribution is focused on feasibility of using comb‐like copolymers of polyethylenimine with poly(2‐ethyl‐2‐oxazoline) (LPEI‐comb‐PEtOx) with varying grafting densities and degrees of polymerization of PEI and PEtOx to deliver DNA molecules into cells. The copolymers form small and well‐defined particles at elevated temperatures, which are used as platforms for binding and condensing DNA. The electrostatic interactions between particles and DNA result in formation of sub‐100 nm polyplex particles of narrow size distribution and different morphology and structure. The investigated gene delivery systems exhibit transfection efficiency dependent on the copolymer chain topology, shape of the polyplex particles, and internalization pathway. Flow cytometry shows enhanced transfection efficiency of the polyplexes with elongated and ellipsoidal morphology. The preliminary biocompatibility study on a panel of human cell lines shows that pure copolymers and polyplexes thereof are practically devoid of cytotoxicity.     

Electrosteric Stabilization of Al(2)O(3), ZrO(2), and 3Y-ZrO(2) Suspensions: Effect of Dissociation and Type of Polyelectrolyte

The mechanisms of eight anionic polyelectrolytes stabilizing colloidal sized alpha-Al(2)O(3), pure ZrO(2), and Y(2)O(3)-doped ZrO(2) particles in aqueous solution are discussed. The polyelectrolytes studied were the Na(+) and NH(4)(+) salts of polyacrylic acid and polymethacrylic acid having different molecular weights. The particle-dispersant interactions were studied by measuring adsorption isotherms, particle size, thickness of adsorbed layer, and zeta potentials by elektrokinetic sonic analysis at different powder volume fractions (straight phi=0.01-0.3), pH, and electrolyte (KCl) content. The dissociation of the polyelectrolytes was studied by potentiometric titrations. The dissociation constant of the polymethacrylates was found to be 0.6 pH unit higher than that for the polyacrylates. High-affinity adsorption isotherms were observed over the pH range when the polyelectrolytes were fully ionized. The results show good correlation between adsorption isotherms and zeta potential data in systems of dispersed, dilute alumina particles. When particles and polymers were of equal charge (the same sign of charge) the polymer shell was thicker. At higher volume fractions (straight phi=0.3), and when alumina particles/added ammonium polyelectrolyte were of equal charge, a maximum in the absolute value of zeta potential resulted. Due to adsorption all the anionic polyelectrolytes studied provided electrosteric stabilization of the alpha-Al(2)O(3), and Y(2)O(3)-doped ZrO(2) suspensions by enhancing the zeta potential to 40 mV or over and by shifting the isoelectric point to lower pH, the low-molecular-weight polyelectrolytes decreasing the isoelectric point more than the polyelectrolytes having higher molecular weight. The polyelectrolytes studied failed to stabilize pure monoclinic ZrO(2) particles. Due to the shortness of the chain of polyelectrolytes studied, no bridging was observed between oppositely charged polyelectrolyte/alumina particles. Copyright 2000 Academic Press.     

Effect of pore former on the properties of casted film prepared from blends of Eudragit NE 30 D and Eudragit L 30 D-55

The casted films of aqueous dispersions of Eudragit NE30 D and Eudragit L30 D-55 containing pore former were prepared. The study investigated the influence of pore former on basic model drug clarithromycin release, water uptake and water vapor permeability from casted film prepared from the blends of neutral polymer dispersion of Eudragit NE30 D and enteric polymer dispersion of Eudragit L30 D-55. This study was concluded that pore former hydroxypropyl methyl cellulose, lactose, polyethylene glycol (PEG) and polyvinyl pyrrolidon (PVP) was released at the beginning of the release process, the rate and extent of water uptake of the polymeric films were much higher in phosphate buffer pH 6.8 than in pH 5.0 and the concentration of pore former have a significant influence on the permeability to water vapour.     

Encapsulation of doxorubicin in magnetic‐polymer hybrid colloidal particles of Eudragit E100 and their hyperthermia and drug release studies

Water‐soluble magnetite Fe₃O₄ nanoparticles were synthesized by coprecipitation that exhibit spherical morphology and superparamagnetic behavior with a saturation magnetization of 46 emu/g. These nanoparticles were coated with amino methacrylate copolymer (Eudragit E100) along with encapsulation of Doxorubicin drug under the action of sonication via a double emulsion solvent evaporation method. The prepared magnetic colloids were evaluated for particle size, surface morphology, surface charge, drug loading capacity, and entrapment efficiency. The drug release studies indicated the sustained release of drug of 92% in 24 hours at physiological pH of 7.4 and drug release kinetics followed first order. The prepared nanoparticles and their colloids were also investigated for magnetic hyperthermia and specific absorption rate values were found to be 2.41, 2.71, and 4.28 W/g at 259, 327, and 518 kHz, respectively. The developed magnetic colloids have the potential to perform controlled hyperthermia and drug release to the target sites.     

Amphipathic and membrane-destabilizing properties of the cationic acrylate polymer Eudragit E100

The cationic acrylate polymer Eudragit E100 (E100) produces a biphasic effect on the stability of casein micelles disrupting their internal structure. These results suggested that this polymer could have some amphipathic character. Therefore, in this study the polymer was characterized with respect to its interaction with different amphipathic systems (bile-acid micelles, lipoproteins and liposomes), cell membranes (red blood cells) and virus membranes (Herpes simplex type 2 virus). As with caseins, a biphasic effect was observed with bile acids with a precipitation phase at low polymer/bile acid ratio and a solubilization phase when the polymer concentration was increased. Upon interaction with human plasma, an important reduction in cholesterol and triglycerides was observed upon remotion of E100 by a rise in pH to 8.5 and centrifugation. In agreement with this finding, an important reduction in plasma lipoproteins was observed upon its treatment with E100 and further remotion by pH rise and centrifugation. However, the amount of the major protein components of human plasma and the activity of several enzymes and antibodies were not affected by their treatment with E100. The membrane-destabilizing properties of E100 were confirmed by its lytic activity on liposomes and red blood cells and by an important antiviral effect of E100 on Herpes simplex virus type 2. Altogether, these results show that, despite its water solubility and cationic character, E100 displays a significative amphipathic and membrane-destabilizing character with potential biotechnological applications. [diagram in text].     

Assembly of Glucose Oxidase and Different Polyelectrolytes by Means of Electrostatic Layer‐by‐Layer Adsorption on Thiolated Gold Surface

A rational strategy for the construction of a bioelectrocatalytic architecture by means of alternate electrostatic adsorption is described. Multilayer films containing glucose oxidase (GOx) and different polyelectrolytes were assembled onto a thiolated‐gold surface and the resulting bioelectrode was used for glucose biosensing. The supramolecular multistructure was prepared by assembling polyethylenimine and Nafion (as anti‐interference barrier), followed by the adsorption of polyethylenimine and DNA (as stabilizing film) and finally by the alternate deposition of polyethylenimine and glucose oxidase (as a biocatalytic layer). The influence of the deposition time and concentration of polyelectrolytes, organization and number of layers on the sensitivity and selectivity of the bioelectrode is discussed. The resulting enzymatic biorecognition layer exhibits very good analytical performance with a fast, sensitive (3.3±0.1)×10⁴ nA M^?1 and highly selective (0% interference for 6.0 mg % uric acid and 2.0×10^?4 M ascorbic acid) response to glucose, demonstrating that the alternate electrostatic adsorption of conveniently selected polyelectrolytes allow a large improvement in the selectivity and sensitivity of a biosensor.     

Single‐step process to produce functionalized multiresponsive polymeric particles

Monodisperse functional multiresponsive particles were prepared by encapsulation of an amphiphilic diblock copolymer during the precipitation polymerization of polystyrene and divinylbenzene in one single step. The amphiphilic diblock copolymer employed throughout this study, polystyrene‐b‐poly (dimethylaminoethyl methacrylate) (PS‐b‐PDMAEMA) has been synthesized by ATRP in two consecutive polymerization steps. After encapsulation of the block copolymer within the microsphere, the surface modification of the particle occurs spontaneously upon exposure to water by surface segregation of the hydrophilic PDMAEMA block, thus without any additional post‐polymerization and/or chemical modification steps. The response of the functionalized particles both to pH and temperature was analyzed by potential zeta and DSC measurements. Upon dispersion of the particles in acidic media, the PDMAEMA block in its charged state is soluble and does not exhibit any change by heating. At higher pH values and temperatures above 35 °C (Low Critical Solubility Temperature of the PDMAEMA block) the hydrophilic segment collapses as detected by differential scanning calorimetry. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3523–3533, 2010     

Effect of preparation temperature in solvent evaporation process on Eudragit RS microsphere properties

Eudragit RS 100 microspheres containing ketoprofen as a model drug were prepared by the solvent evaporation method using an acetone/liquid paraffin solvent system. The influence of various preparation temperatures: 10, 25, 35, and 40 degrees C, on particle size and morphology, drug content and release kinetics, and drug crystal state was evaluated. With increasing temperature, microsphere average size was found to increase and particle size distribution to widen significantly. At 10 degrees C particles of irregular shape are formed, whereas higher temperatures gradually improve the sphericity of microspheres. As can be seen from SEM photographs, particle surface roughness decreases as preparation temperature increases. It was found that temperature had no effect either on ketoprofen microencapsulation efficiency or on its crystal state, but it does influence emulsion-stabilizer incorporation. Ketoprofen forms solid solution in Eudragit matrix and maintains amorphous state for significant period of time. Drug release rates from microspheres correlated with microspheres' surface roughness and to a lesser extent with particle size.     

Preparation of Functional Water‐Soluble Low‐Cytotoxic Poly(methacrylate)s With Pendant Cationic L‐Lysines for Efficient Gene Delivery

In this work, we present the preparation of water‐soluble poly(methacrylate)s with pendant cationic L ‐lysines PHMLs(6–30 K). Plasmid DNA binding affinity as well as particle sizes and zeta potentials of the polyplexes were examined for these PHML vectors, and their cytotoxicities were assayed with HeLa cells by CCK‐8 and lactate dehydrogenase kits. Gene transfection efficacy and intracellular uptake of the polyplexes by the PHML vectors were also studied with HeLa cells. As a result, it was revealed that the low cytotoxic PHMLs tended to exhibit gene transfection efficiencies significantly higher than those of the linear structural PLL (15–30 K) control, in particular the molecular weight of a PHML vector remarkably influenced its pDNA binding affinity, transfection efficacy and intracellular uptake of the polyplexes.

     

A novel strategy to utilize ethylene glycol‐ionic liquids for the selective precipitation of polysaccharides

In the present work, three hydrophilic ionic liquids based on the combination between imidazolium cations attached with ethylene glycol polymers of various lengths and hexafluorophosphate anion were designed and synthesized for the separation of polysaccharides. By employing dextran 100 kDa as model compound, the effects of ionic liquid content, solvent/anti‐solvent volume, and temperature on its recovery efficiency were investigated systematically. The ability of these ionic liquids to precipitate dextran 100 kDa, increases with the elongation of ethylene glycol polymer chain. The established ionic liquid‐based precipitation system was successfully applied to selectively precipitate polysaccharides from water extracts of three traditional Chinese medicines and the precipitation could be achieved in about 15 min. In addition, the different precipitation responses of acidic, neutral, and basic polysaccharides in the ionic liquid‐based precipitation system and theoretical calculations both suggested that the selective precipitation of polysaccharides was probably mediated by interaction between ionic liquids and polysaccharides. The proposed strategy facilitated the isolation and purification of polysaccharides and may trigger a novel application of ionic liquids in carbohydrate research.     

Liquid Phase Hydrogenolysis of Biomass‐derived Lactate to 1,2‐Propanediol over Silica Supported Cobalt Nanocatalyst

Liquid phase hydrogenolysis of ethyl lactate to 1,2‐propanediol was performed over silica supporting cobalt catalysts prepared by two different methods: precipitation‐gel (PG) technique and deposition‐precipitation (DP) procedure. The cobalt species (Co₃O₄/cobalt phyllosilicate) present in the corresponding calcined PG and DP catalysts were different as a consequence of the preparation methods, and Co OH Co olation and Si O Co oxolation molecular mechanisms were employed to elucidate the chemical phenomena during the different preparation procedures. In addition, the texture (BET), reduction behavior (TPR and in‐situ XRD), surface dispersion and state of cobalt species (XPS), and catalytic performance differ greatly between the samples. Because of small particle size, high dispersion of cobalt species and facile reducibility, the Co/SiO₂ catalyst prepared by precipitation‐gel method presented a much higher activity than the catalyst prepared by deposition‐precipitation method. Metallic cobalt is assumed to be the catalytically active site for the hydrogenolysis reaction according to the catalytic results of both cobalt samples reduced at different temperatures and the structure changes after reaction.     

Nanoparticulate Hollow TiO2 Fibers as Light Scatterers in Dye‐Sensitized Solar Cells: Layer‐by‐Layer Self‐Assembly Parameters and Mechanism

Hollow structures show both light scattering and light trapping, which makes them promising for dye‐sensitized solar cell (DSSC) applications. In this work, nanoparticulate hollow TiO₂ fibers are prepared by layer‐by‐layer (LbL) self‐assembly deposition of TiO₂ nanoparticles on natural cellulose fibers as template, followed by thermal removal of the template. The effect of LbL parameters such as the type and molecular weight of polyelectrolyte, number of dip cycles, and the TiO₂ dispersion (amorphous or crystalline sol) are investigated. LbL deposition with weak polyelectrolytes (polyethylenimine, PEI) gives greater nanoparticle deposition yield compared to strong polyelectrolytes (poly(diallyldimethylammonium chloride), PDDA). Decreasing the molecular weight of the polyelectrolyte results in more deposition of nanoparticles in each dip cycle with narrower pore size distribution. Fibers prepared by the deposition of crystalline TiO₂ nanoparticles show higher surface area and higher pore volume than amorphous nanoparticles. Scattering coefficients and backscattering properties of fibers are investigated and compared with those of commercial P25 nanoparticles. Composite P25–fiber films are electrophoretically deposited and employed as the photoanode in DSSC. Photoelectrochemical measurements showed an increase of around 50 % in conversion efficiency. By employing the intensity‐modulated photovoltage and photocurrent spectroscopy methods, it is shown that the performance improvement due to addition of fibers is mostly due to the increase in light‐harvesting efficiency. The high surface area due to the nanoparticulate structure and strong light harvesting due to the hollow structure make these fibers promising scatterers in DSSCs.     

Mixed system of Eudragit s-100 with a designed amphipathic peptide: control of interfacial elasticity by solution composition

We report an interfacially active system based on an informational peptide surfactant mixed with an oppositely charged polyelectrolyte. The 21-residue cationic peptide, AM1, has previously been shown to respond reversibly to pH and metal ions at fluid interfaces, forming elastic films that can be rapidly switched to collapse foams or emulsions on demand. Here we report the reversible association of AM1 with the methacrylate-based anionic polymer Eudragit S-100. The strength of the association, in bulk aqueous solution, is modulated by added metal ions and by ionic strength. Addition of zinc ions to the peptide-polymer system promotes complex formation and phase separation, while addition of a chelating agent reverses the association. The addition of salt weakens peptide-polymer interactions in the presence or absence of zinc. At the air-water interface, Eudragit S-100 forms an elastic mixed film with AM1 in the absence of metal, under conditions where the peptide alone does not show interfacial elasticity. When zinc is present, the elasticity of the mixed film is increased, but the rate of interfacial adsorption slows due to formation of peptide-polymer complexes in bulk solution. An understanding of these interactions can be used to identify favorable foam-forming conditions in the mixed system.     

Synthesis and characterization of polyamine‐based cyclophosphazene hybrid microspheres

Starting with hexachlorocyclotriphosphazene (HCCP) and branched polyethylenimine (bPEI) crosslinked cyclomatrix polyphosphazene poly(HCCP‐co‐bPEI) microspheres are prepared by precipitation polymerization in acetonitrile at 50 °C under ultrasound irradiation. The influence of varying reagent ratios on the chemical composition, morphology, and physical and chemical properties of the microspheres is investigated. Furthermore, the microspheres are characterized by Fourier‐transform infrared spectroscopy, dynamic light scattering (DLS), X‐ray photoelectron spectroscopy, elemental analysis, as well as ³¹P MAS NMR. FESEM and DLS analysis show microspheres of smooth and spherical shape which swell both in water and acetonitrile. The particle diameters in the dry state range from 0.4 to 0.9 μm, but due to swelling a size increase between 45 and 140% is observed depending on the chemical composition and the solvent medium. The thermal stability of the microspheres ranges from 262 to 351 °C. The presence of reactive amine groups on the surface is proven by electrophoretic mobility measurements and chemical modification with two model compounds. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 527–536     

Amino Acid–Substituted Dextran‐Based Non‐Viral Vectors for Gene Delivery

To form bio‐inspired non‐viral vectors for DNA delivery, the polysaccharide dextran is allowed to react with Boc‐amino protected amino acids glycine, β‐alanine, and L‐lysine activated with 1,1’‐carbonyldiimidazole and subsequent dextran ester deprotection. A library of such dextran esters is made available to investigate the relationship between polymer structure, complex formation, stability, toxicity, and transfection. Only dextran esters of β‐alanine and L‐lysine are able to efficiently interact with DNA as shown by dye exclusion assays, to form nanosized complexes (70–110 nm) with positive zeta potential. With increasing substitution degree and complex charge ratios, the L‐lysine esters accomplish more effective binding and protection of DNA against enzymatic degradation than β‐alanine esters. However, luciferase reporter gene assays reveal higher transfection for β‐alanine than for L‐lysine esters due to a more effective DNA release and better suited buffing area of the amino groups triggering the endosomal release. Conclusively, β‐alanine‐substituted dextran derivatives may serve as promising non‐viral vectors.     

Copolymerization of 2‐hydroxyethyl methacrylate with a comonomer with spiroacetal moiety

The study reports the synthesis of a copolymer based on 2‐hydroxyethyl methacrylate and 3,9‐divinyl‐2,4,8,10‐tetraoxaspiro[5.5]undecane (U) acquired through radical polymerization in the presence of 2,2′‐azobis(2‐methylpropionitrile). The attempt was to have a solid content as high as 10 wt %. The polymerization process was conducted in the presence of a classic ionic surfactant—sodium lauryl sulfate—and comparatively using two variants of protective colloid β‐cyclodextrin and poly(aspartic acid), respectively. The prepared dispersions were characterized from the viewpoint of their hydrodynamic radius, zeta potential, and conductivity evolution during syntheses. The mean particle size and size distribution and zeta potential and conductivity were also evaluated for the synthesized polymeric particles. The compositions of the polymers were confirmed by FTIR and ¹H NMR spectra, and also, the thermal stability of the polymeric compounds was evaluated. SEM and AFM investigations of the polymer morphology are also presented. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Statistical fluctuation in zeta potential distribution of nanoliposomes measured by on‐chip microcapillary electrophoresis

The zeta potential of nanoliposomes with a diameter below 100 nm has been studied by the combined use of on‐chip microcapillary electrophoresis (μCE) and sensitive fluorescence imaging. Tracking the electrophoretic migration of individual nanoliposomes has enabled the accurate evaluation of the zeta potential distribution of nanoliposomes and the first observation of its abnormal broadening due to a statistical fluctuation phenomenon specific to the “nanoscale world.” The materials used for liposome preparation were phosphocholine as the neutral lipid, phosphatidylserine as the anionic lipid, and cholesterol. The size of the liposomes encapsulating calcein, a fluorescent dye used for imaging convenience, was tailored by extrusion through polycarbonate membrane filters of different pore sizes ranging from 50 to 1000 nm. The on‐chip μCE system comprised a μCE chip, a laser source, an inverted microscope, and an electron‐multiplying charge‐coupled device camera. The electrophoresis experiment using this system revealed that the relative standard deviation of the zeta potential distribution of nanoliposomes is inversely proportional to their diameter and apparently increases below 100 nm. This abnormal broadening of zeta potential distribution of nanoliposomes is explained by prominent discreteness effect of the number of anionic lipid molecules in nanoliposomes.