Kinetics of crude oil combustion

In this research, thermal characterization and kinetics of Karakus crude oil in the presence of limestone matrix is investigated. Thermogravimetry (TG/DTG) is used to characterize the crude oil in the temperature range of 20-900°C, at 10°C min ^-1 heating rate using air flow rate of 20 mL min ^-1. In combustion with air, three distinct reaction regions were identified known as low temperature oxidation (LTO), fuel deposition (FD) and high temperature oxidation (HTO). Five different kinetic methods used to analyze the TG/DTG data to identify reaction parameters as activation energy and Arrhenius constant. On the other hand different f(α) models from literature were also applied to make comparison. It was observed that high temperature oxidation temperature (HTO) activation energy of Karakus crude oil is varied between 54.1 and 86.1 kJ mol ^-1, while low temperature oxidation temperature (LTO) is varied between 6.9 and 8.9 kJ mol ^-1.     

Effect of different clay concentrations on crude oil combustion kinetics by thermogravimetry

The objective of this research was to investigate the effect of different clay composition and concentrations on the thermal behaviour and kinetics of heavy crude oil in limestone matrix by thermogravimetry (TG/DTG). In TG/DTG experiments, three distinct reaction regions were identified in all of the crude oil + limestone mixture known as low temperature oxidation (LTO), fuel deposition (FD) and high temperature oxidation (HTO) respectively. Addition of clay to porous matrix significantly affected the reaction regions. Significant reduction of activation energy due to addition of clay to crude oil indicates the catalytic effect of clay on crude oil combustion.     

Thermal kinetics study of light oil oxidation using TG/DTG techniques

In this study, the oxidation behavior of crude oils in the presence and absence of rock cuttings was investigated by thermogravimetry/derivative thermogravimetry (TG/DTG) techniques. Prior to these tests, the composition of cuttings and properties of crude oils were analyzed. Three obvious reaction regions were observed from the TG/DTG curves which are recognized as low-temperature oxidation (LTO), fuel deposition (FD), and high-temperature oxidation. The effects of light components (C_7–15), heavy fractions (asphaltene, paraffin, resin), and cutting on oil oxidation behavior were analyzed. Kinetic analysis of crude oils and oil + cutting mixtures was performed by Arrhenius method, and the data were analyzed at last. Results show that high content C_7–15 hydrocarbons can provide negative effect on the LTO behavior of crude oil. On the contrary, the high content unsaturated heavy hydrocarbons including asphaltene, paraffin, and resin are benefit for the oxidation performance. In addition, a shortened FD stage and higher peak temperature in LTO region are observed by addition of cutting. Cutting especially clay in it plays an active role of catalyzing in oil oxidation reaction.     

Non-isothermal kinetic analysis and feasibilty study of medium grade crude oil field

In this research, non-isothermal kinetics and feasibility study of medium grade crude oil is studied in the presence of a limestone matrix. Experiments were performed at a heating rate of 10°C min⁻¹, whereas the air flow rate was kept constant at 50 mL min⁻¹ in the temperature range of 20 to 600°C (DSC) and 20 to 900°C (TG). In combustion with air, three distinct reaction regions were identified in all crude oil/limestone mixtures, known as low temperature oxidation (LTO), fuel deposition (FD) and high temperature oxidation (HTO). The activation energy values were in the order of 5–9 kJ mol⁻¹ in LTO region and 189–229 kJ mol⁻¹ in HTO region. It was concluded that the medium grade crude oil field was not feasible for a self-sustained combustion process.     

Light crude oil combustion in the presence of limestone matrix

In this study the combustion characteristics of crude oils (Karakuę and Beykan) in the presence of a limestone matrix were determined using the thermogravimetry (TG/DTG). Experiments were performed at a heating rate of 10°C min^-1, whereas the air flow rate was kept constant at 10 L h^-1 in the temperature range of 20-900°C. In combustion with air, three distinct reaction regions were identified in all crude oil/limestone mixtures studied known as low temperature oxidation (LTO), fuel deposition (FD) and high temperature oxidation (HTO). The individual activation energies for each reaction region may be attributed to different reaction mechanisms, but they do not give any indication of the contribution of each region to the overall reactivity of the crude oils. Depending on the characteristics, the mean activation energy of samples varied between 50.3 and 55.8 kJ mol^-1. This revised version was published online in August 2006 with corrections to the Cover Date.     

Polyoxometalate Ionic Liquids as Self‐Repairing Acid‐Resistant Corrosion Protection

Corrosion is a global problem for any metallic structure or material. Herein we show how metals can easily be protected against acid corrosion using hydrophobic polyoxometalate‐based ionic liquids (POM‐ILs). Copper metal disks were coated with room‐temperature POM‐ILs composed of transition‐metal functionalized Keggin anions [SiW₁₁O₃₉TM(H₂O)]^n? (TM=Cu^II, Fe^III) and quaternary alkylammonium cations (C_nH_{2 n+1})₄N⁺ (n=7–8). The corrosion resistance against acetic acid vapors and simulated “acid rain” was significantly improved compared with commercial ionic liquids or solid polyoxometalate coatings. Mechanical damage to the POM‐IL coating is self‐repaired in less than one minute with full retention of the acid protection properties. The coating can easily be removed and recovered by rinsing with organic solvents.     

Ionic Association of the Ionic Liquids [C4mim][BF4], [C4mim][PF6], and [Cnmim]Br in Molecular Solvents

Considering the ionic nature of ionic liquids (ILs), ionic association is expected to be essential in solutions of ILs and to have an important influence on their applications. Although numerous studies have been reported for the ionic association behavior of ILs in solution, quantitative results are quite scarce. Herein, the conductivities of the ILs [C_nmim]Br (n=4, 6, 8, 10, 12), [C₄mim][BF₄], and [C₄mim][PF₆] in various molecular solvents (water, methanol, 1‐propanol, 1‐pentanol, acetonitrile, and acetone) are determined at 298.15 K as a function of IL concentration. The conductance data are analyzed by the Lee–Wheaton conductivity equation in terms of the ionic association constant (K_A) and the limiting molar conductance (Λ_m⁰). Combined with the values for the Br^? anion reported in the literature, the limiting molar conductivities and the transference numbers of the cations and [BF₄]^? and [PF₆]^? anions are calculated in the molecular solvents. It is shown that the alkyl chain length of the cations and type of anion affect the ionic association constants and limiting molar conductivities of the ILs. For a given anion (Br^?), the Λ_m⁰ values decrease with increasing alkyl chain length of the cations in all the molecular solvents, whereas the K_A values of the ILs decrease in organic solvents but increase in water as the alkyl chain length of the cations increases. For the [C₄mim]⁺ cation, the limiting molar conductivities of the ILs decrease in the order Br^?>[BF₄]^?>[PF₆]^?, and their ionic association constants follow the order [BF₄]^?>[PF₆]^?>Br^? in water, acetone, and acetonitrile. Furthermore, and similar to the classical electrolytes, a linear relationship is observed between ln K_A of the ILs and the reciprocal of the dielectric constants of the molecular solvents. The ILs are solvated to a different extent by the molecular solvents, and ionic association is affected significantly by ionic solvation. This information is expected to be useful for the modulation of the IL conductance by the alkyl chain length of the cations, type of anion, and physical properties of the molecular solvents.     

Catalytic effect analysis of metallic additives on light crude oil by TG and DSC tests

This research aimed at the investigation of the effect of different metallic additive on the combustion and kinetic behavior of crude oil. For this purpose, the thermal behavior of the oil-only and oil–metallic salts mixtures were studies by the thermogravimetry (TG)/derivative thermogravimetry and differential scanning calorimetry (DSC) on heating rate at 10 °C min^?1. The result shows that Dagang crude oil exhibited apparent low temperature oxidation (LTO), fuel deposition, and high temperature oxidation processes. With the addition of metallic salts, the LTO process has been shortened and samples added CuSO₄, CrCl₃·6H₂O, and AlCl₃·6H₂O achieved a much lower peak temperature than that of oil. Based on the Arrhenius model, metallic additives were proven to have obvious influence on the combustion activation energy. And, by comprehensive analysis of TG/DSC profile and activation energy, ZnSO₄ exhibited a positive influence on light crude oil combustion during the high pressure air injection process.     

Influence of reservoir rock composition on the combustion kinetics of crude oil

In this research, the effect of different lithology (limestone and sandstone) on the combustion of light crude oils was investigated using thermal analysis techniques. Three distinct reaction regions were identified in all of the crude oil+limestone and sandstone mixtures, known as low temperature oxidation (LTO), fuel deposition (FD) and high temperature oxidation (HTO), respectively. Kinetic analysis of the crude oil+limestone and sandstone mixtures was performed using Coats and Redfern method and the results are discussed.     

Effects of Cationic Structure on Cellulose Dissolution in Ionic Liquids: A Molecular Dynamics Study

In recent years, great progress has been made in the dissolution of cellulose with ionic liquids (ILs). However, the mechanism of cellulose dissolution, especially the role the IL cation played in the dissolution process, has not been clearly understood. Herein, the mixtures of cellulose with a series of imidazolium‐based chloride ionic liquids and 1‐butyl‐3‐methyl pyridinium chloride ([C₄mpy]Cl) were simulated to study the effect that varying the heterocyclic structure and alkyl chain length of the IL cation has on the dissolution of cellulose. It was shown that the dissolution of cellulose in [C₄mpy]Cl is better than that in [C₄mim]Cl. For imidazolium‐based ILs, the shorter the alkyl chain is, the higher the solubility will be. In addition, an all‐atom force field for 1‐allyl‐3‐methyl imidazolium cation ([Amim]⁺) was developed, for the first time, to investigate the effect the electron‐withdrawing group within the alkyl chain of the IL cation has on the dissolution of cellulose. It was found that the interaction energy between [Amim]⁺ and cellulose was greater than that between [C₃mim]⁺ and cellulose, indicating that the presence of electron‐withdrawing group in alkyl chain of the cation enhanced the interaction between the cation and cellulose due to the increase of electronegativity of the cations. These findings are used to assess the cationic effect on the dissolution of cellulose in ILs. They are also expected to be important for rational design of novel ILs for efficient dissolution of cellulose.     

烷基咪唑离子液体对脂肪酶催化酯水解反应活性的影响

考察了1-烷基-3-甲基咪唑类离子液体对柱状假丝酵母脂肪酶(CRL)催化橄榄油水解反应活性的影响,利用电导法确定了磷酸盐缓冲液中Br^-,Cl^-,[BF₄]^-系列咪唑离子液体的临界胶束浓度(CMC)和[PF₆]^-系列咪唑离子液体的溶解度.结果显示,离子液体的阴、阳离子对酶活性的影响规律与离子液体的Kosmotropicity性质无明显关联,但与离子液体在体系中的含量密切相关,在最适离子液体含量时,酶活性达到最高;阳离子[C_nMIM]⁺中的n越大,可促进酶活性的离子液体适宜含量越低;Br^-,[BF₄]^-系列离子液体的浓度超过CMC时则抑制酶活;阴离子对酶活性的最大促进作用顺序为Br^->Cl^->[BF₄]^->[PF₆]^-.离子液体对酶活性的影响随体系pH和温度的不同而改变,在最适离子液体浓度时的最适pH均为7.000.在pH 7.000,30 ^oC以及[C₈MIM]Br离子液体浓度为47.6 mmol/L的最佳条件下,最高相对酶活力和比活力分别达到1734%和54.4 U/mg protein.     

Doubly charged benzene and isomeric dications. Fragmentation energetics and charge distributions calculated by MINDO/3 molecular orbital theory

MINDO/3 calculations for singlet and triplet doubly charged benzene [C₆H₆]²⁺ are in satisfactory agreement with the experimentally determined values of the vertical double ionization energy of benzene; calculations for straight chain isomeric structures are consistent with the observed kinetic energy release on fragmentation to [C₅H₃]⁺ and [CH₃]⁺. Symmetrical doubly charged benzene ions relax to a less symmetrical cyclic structure having sufficient internal energy to fragment by ring opening and hydrogen transfer towards the ends of the carbon chain. Fragmentation of [CH₃C₄CH₃]²⁺ to [CH₃C₄]⁺ and [CH₃]⁺ is a relatively high energy process (A), whereas both (B): [CH₃CHC₃CH₂]²⁺ to [CHC₃CH₂]⁺ and [CH₃]⁺ and (C): [CH₃CHCCHCCH]²⁺ to [CHCCHCCH]⁺ and [CH₃]⁺ may be exothermic processes from doubly charged benzene. Furthermore, the calculated energy for the reverse of process (A) is less than the experimentally observed kinetic energy released, whereas larger energies for the reverse of processes B and C are predicted. Heats of formation of homologous series [HC_n]⁺, [CH₃C_n]⁺, [CH₂C_n?2CH]⁺, [CH₃C_n?2CH₂]⁺ and [CH₂?CHC_n?3CH₂]⁺ with 1 < n < 6 are calculated to aid prediction of the most stable products of fragmentation of doubly charged cations. The homologous series [CH₂C_n?2CH]⁺ is relatively stable and may account for ready fragmentation of doubly charged ions to [C_nH₃]⁺; alternatively the symmetrical [C₅H₃]⁺ ion [CHCCHCCH]⁺ may be formed. Dicoordinate carbon chains appear to be important stabilizing features for both cations and dications.     

Tetrahydrothiophene-Based Ionic Liquids: Synthesis and Thermodynamic Characterizations

S-alkyltetrahydrothiophenium, [C_nTHT]⁺ bis(trifluorosulfonyl)imide, [NTf₂]⁻ room temperature ionic liquids (ILs) and tetraphenylborate, [BPh₄]⁻ salts with alkyl chain lengths from C₄ to C₁₀ have been prepared. The ILs and salts were characterized and their purity verified by ¹H- and ¹³C-nuclear magnetic resonance, elemental analysis, ion chromatography, Karl-Fischer titration, single crystal X-ray diffraction as well as thermogravimetric analysis. The experimentally determined density and viscosity decrease with increasing temperature. The experimental solubility of the [C_nTHT][NTf₂]-ILs in water (75 to 2.2 mg/L for C₄ to C₁₀) was modelled with very good agreement by Perturbed Chain Statistical Associating Fluid Theory (PC-SAFT), based on the extremely low vapor pressures for the [C_nTHT][NTf₂]-ILs measured in this work (4.15 to 0.037 ⋅ 10⁻⁷×p_sat for C₄ to C₁₀). PC-SAFT is able to predict and correlate different thermodynamic properties by estimating the Helmholtz residual energy.     

Ionic liquids enhanced oil recovery from oily sludge-experiment and mechanism

The oily sludge would cause environment pollution, and would cause the heavy oil waste. Therefore, it was vital for us to find novel methods to obtain heavy oil from the oily sludges. In this study, the [C₁₂mim][PF₆] and [C₁₂mim][Br] ionic liquids(ILs) were used to enhance the oil recovery. The toluene could obtain the highest oil recovery, and both the two ILs could increase the oil recovery. Toluene could obtain the highest oil recovery (89.4 wt%), and n-octane could obtain the lowest oil recovery (76.8 wt%). [C₁₂mim] [PF₆] could efficiently increase the heavy oil recovery to 91.2 wt%(by toluene). The [C₁₂mim][Br] could increase the heavy oil recovery further. Both the [C₁₂mim] [PF₆] and the [C₁₂mim][Br] ionic liquids could increase the heavy ois C/H ratio, decrease heavy oil viscosity and increase the sands hydrophilicity. The [C₁₂mim][Br] ionic liquids showed better effect. In addition, the ionic liquids could increase the solvents recovery, and the ionic liquids recovery were high. Therefore, the ionic liquids enhanced oil recovery could be recycled to ten times. The two ionic liquids could effectively decrease the heavy oil interaction force, and when the ionic liquids increased to 200 ppm, the force remained stable. In the end, the ionic liquids enhancing solvent extraction mechanism was put forward.     

Fluorous ionic liquids as solvents for the liquid-liquid extraction of metal ions by macrocyclic polyethers

The predominant mode of strontium ion transfer from aqueous nitrate media into a series of 1-fluoroalkyl-3-methylimidazolium bis[(trifluoromethylsulfonyl)]imides containing dicyclohexano-18-crown-6 (DCH18C6) is shown to shift from cation exchange to strontium nitrato-crown ether complex partitioning as the length of the fluoroalkyl substituent is increased. Fluoroalkyl substituents are shown to be only slightly more effective than their non-fluorous analogs at inducing this shift. At the same time, the fluorinated ionic liquids (ILs) yield strontium distribution ratios as much as an order of magnitude lower than the corresponding 1-alkyl-3-methylimidazolium (C_nmim⁺) salts. Fluorous ILs thus appear to offer no compelling advantages over C_nmim⁺ ionic liquids as extraction solvents.     

原油组分低温氧化机理和反应活性实验研究

分析了原油和原油组分低温氧化的机理,通过实验进行了不同油品低温氧化反应,考察了氧化反应前后原油族组成的变化,并研究了单组分(正十六烷、蜡、蒽、沥青质)在不同温度下的低温氧化速率和反应活性,得出了不同原油组分的低温氧化反应的活化能。结果表明,稠油较轻质油有更好的氧化反应活性,在较低温度下稠油更容易被氧化,原油中不同组分及含量是影响氧化反应活性和氧化反应速率的重要因素,重组分的沥青质和长链烷烃在低温下(70~90℃)氧化活性较高,正十六烷和蒽反应活性较之重组分低。揭示了原油组分低温氧化反应机理以及不同组分氧化反应活性的区别,为油田注空气工艺方案设计提供基础。     

Reactive Half‐Metallocenium Ionic Liquids That Undergo Solventless Ligand Exchange

The piano‐stool half‐metallocenium cations [Fe(C₅R₅)(CO)₂ L ]⁺ (C₅R₅=C₅H₅, C₅Me₅, C₅Me₄Et; L =1‐pentene, nBuCN, MeCN, Me₂S, NH₃, NMe₃, pyridine) provide ionic liquids (ILs) with the bis(trifluoromethanesulfonyl)imide (Tf₂N) anion without introducing long alkyl chains. Their melting points are affected by molecular symmetry, and their thermal stabilities reflect the strength of the metal–ligand bonding. These are reactive liquids that show solventless ligand exchange reactions by gas absorption. The direction of the ligand‐exchange reaction is correlated with the stabilities. Based on the variation of the melting points, these ILs undergo transformations between the liquid and solid phases associated with the reaction.     

Absolute Brønsted Acidities and pH Scales in Ionic Liquids

Although receiving large interest over the last years, some fundamental aspects of Brønsted acidity in ionic liquids (ILs) have up to now been insufficiently highlighted. In this work, standard states, activity, and activity coefficient definitions for IL solvent systems were developed from general thermodynamic considerations and then extended to a general mixed solvent standard state. By using the bromide/bromoaluminate systems as representative ILs, formulae for thermodynamically consistent pH scales for ILs with simple (Br^?) and complex ([Al_nBr_3n+1]^?) anions were derived on the basis of the chemical potential of the proton. Supported by quantum chemical [ccsd(t)/MP2/DFT/COSMO‐RS] calculations, Gibbs solvation energies of the proton were calculated, which allowed the ILs to be ranked in absolute acidity, that is, pH_abs or μ_abs(H⁺, IL), and additionally allowed their acidity to be compared with molecular Brønsted acid systems. It was shown that bromoaluminate ILs are suited for reaching superacidic conditions. The complexity of autoprotolysis processes in C₆MIM⁺[AlBr₄]^? (C₆MIM=1‐hexyl‐3‐methylimidazolium) with or without the addition of basic (i.e. Br^?) or acidic (AlBr₃ and/or HBr) solutes was examined in detail by model calculations, and they indicated a large thermodynamic influence of small deviations from the exact stoichiometric composition.     

Synthesis,Stabilization, Functionalization and,DFT Calculations of Gold Nanoparticles in Fluorous Phases (PTFE and Ionic Liquids)

Gold nanoparticles (Au‐NPs) were reproducibly obtained by thermal, photolytic, or microwave‐assisted decomposition/reduction under argon from Au(CO)Cl or KAuCl₄ in the presence of n‐butylimidazol dispersed in the ionic liquids (ILs) BMIm⁺BF₄^?, BMIm⁺OTf^?, or BtMA⁺NTf₂^? (BMIm⁺=n‐butylmethylimidazolium, BtMA⁺=n‐butyltrimethylammonium, OTf^?=^?O₃SCF₃, NTf₂^?=^?N(O₂SCF₃)₂). The ultra small and uniform nanoparticles of about 1–2 nm diameter were produced in BMIm⁺BF₄^? and increased in size with the molecular volume of the ionic liquid anion used in BMIm⁺OTf^? and BtMA⁺NTf₂^?. Under argon the Au‐NP/IL dispersion is stable without any additional stabilizers or capping molecules. From the ionic liquids, the gold nanoparticles can be functionalized with organic thiol ligands, transferred, and stabilized in different polar and nonpolar organic solvents. Au‐NPs can also be brought onto and stabilized by interaction with a polytetrafluoroethylene (PTFE, Teflon) surface. Density functional theory (DFT) calculations favor interactions between IL anions instead of IL cations. This suggests a Au???F interaction and anionic Au_n stabilization in fluorine‐containing ILs. The ¹⁹F NMR signal in BMIm⁺BF₄^? shows a small Au‐NP concentration‐dependent shift. Characterization of the dispersed and deposited gold nanoparticles was done by transmission electron microscopy (TEM/HRTEM), transmission electron diffraction (TED), dynamic light scattering (DLS), UV/Vis absorbance spectroscopy, scanning electron microscopy (SEM), electron spin resonance (ESR), and electron probe micro analyses (EPM, SEM/EDX).     

Jahn-teller effects in the MNDO approximation: structures of the molecular cations of some simple organoberyllium compounds

The MNDO method gives geometries for the molecular cations of organoberyllium compounds of types BeR₂ and HBeR (R = CH₃, CHCH₂, CCH, CN, C₅H₅), of C₄H₄Be and CH₃BeBeH₃ and of the series CH_4?n(BeH)_n (n = 0–4) which have symmetries in precise accord with the predictions of the Jahn-Teller theorem. In the series CH_4?n(BeH)_n and CH_4?n(BeH)_n⁺, the barriers to inversion via a planar intermediate decrease with increasing n, are significantly smaller for the cations than for the neutral molecules, and are zero for CH(BeH)₃⁺ and C(BeH)₄⁺, both of which have their minimum energy when strictly planar at carbon.