Fabrication and analysis of thin-film GaAs solar cell on flexible thermoplastic substrate using a low-pressure cold-welding

We present flexible thin-film GaAs solar cells fabricated on thermoplastic substrates by a low-pressure cold-welding and epitaxial lift-off process. The use of polyethylene terephthalate (PET) film as a flexible substrate enables cold welding (130 °C) of gold layers between a thin-film GaAs solar cell and PET film with very low mechanical pressure (0.4 MPa), due to their thermoplastic properties. The feasibility of the proposed technique was demonstrated by fabricating GaAs single junction solar cells (without antireflection coating) on PET film, having an efficiency of 13.2%. The fabricated solar cell also showed a stable performance after 2000 cycles of bending.     

Radiation Damage Analysis of Individual Subcells for GaInP/GaAs/Ge Solar Cells Using Photoluminescence Measurements

The radiation damage of three individual subcells for GaInP/GaAs/Ge triple-junction solar cells irradiated with electrons and protons is investigated using photoluminescence(PL) measurements. The PL spectra of each subcell are obtained using different excitation lasers. The PL intensity has a fast degradation after irradiation,and decreases as the displacement damage dose increases. Furthermore, the normalized PL intensity varying with the displacement damage dose is analyzed in detail, and then the lifetime damage coefficients of the recombination centers for GaInP top-cell, GaAs mid-cell and Ge bottom-cell of the triple-junction solar cells are determined from the PL radiative efficiency.     

GaAs-InP异质材料的结构特性和光学特性研究

我们在低压金属有机汽相沉积(MOCVD)设备上采用两步升温法与金属有机源流量周期调制生长界面过渡层方法制备出GaAs-InP材料,并对此进行了X-射线衍射、低温光致发光谱(PL)和Raman谱分析,结果表明,GaAs外延层的位错密度低于用两步升温法得到的GaAs材料,PL谱峰较强,GaAs的特征激子峰和杂质相关的激子峰同时被测到。Raman谱PL谱的峰移表明GaAs外延层处于(100)双轴伸张应力下,应力大小随温度变化是由于GaAs、InP之间的热膨胀系数不同。     

空间用GaInP/GaAs/In0.3Ga0.7 As(1 eV)倒装三结太阳电池研制

采用阶变缓冲层技术 (step-graded) 外延生长了具有更优带隙组合的倒装GaInP/GaAs/In_0.3Ga_0.7As(1.0 eV) 三结太阳电池材料, TEM和HRXRD测试表明晶格失配度为2%的In_0.3Ga_0.7As 底电池具有较低的穿透位错密度和较高的晶体质量, 达到太阳电池的制备要求. 通过键合、剥离等工艺制备了太阳电池芯片. 面积为 10.922 cm² 的太阳电池芯片在空间光谱条件下转换效率达到32.64% (AM0, 25 ℃), 比传统晶格匹配的 GaInP/GaAs/Ge(0.67 eV) 三结太阳电池的转换效率提高3个百分点. 关键词： 太阳电池 三结 倒装结构     

Temperature-Dependent Photoluminescence Analysis of 1.0 MeV Electron Irradiation-Induced Nonradiative Recombination Centers in n~+-p GaAs Middle Cell of GaInP/GaAs/Ge Triple-Junction Solar Cells

The effects of irradiation of 1.0 MeV electrons on the n~+-p GaAs middle cell of GaInP/GaAs/Ge triple-junction solar cells are investigated by temperature-dependent photoluminescence(PL) measurements in the 10-300 K temperature range. The appearance of thermal quenching of the PL intensity with increasing temperature confirms the presence of a nonradiative recombination center in the cell after the electron irradiation, and the thermal activation energy of the center is determined using the Arrhenius plot of the PL intensity.Furthermore,by comparing the thermal activation and the ionization energies of the defects, the nonradiative recombination center in the n~+-p GaAs middle cell acting as a primary defect is identified as the E5 electron trap located at E_c-0.96 eV.     

Photoluminescence properties of GaAs nanowire ensembles with zincblende and wurtzite crystal structure

Self‐standing III–V nanowires (NWs) are promising building blocks for future optoelectronic devices such as LEDs, lasers, photodetectors and solar cells. In this work, we present the results of low temperature photoluminescence (PL) characterization of GaAs NWs grown by Au‐assisted molecular beam epitaxy (MBE), coupled with the transmission electron microscopy (TEM) structural analysis. PL spectra contain exci‐ ton peaks from zincblende (ZB) and wurtzite (WZ) crystal structures of GaAs. The peaks are influenced by the quantum confinement effects. PL bands corresponding to the exciton emission from ZB and WZ crystal phases are identified, relating to the PL peaks at 1.519 eV and 1.478 eV, respectively. The obtained red shift of 41 meV for WZ GaAs should persist in thin NWs as well as in bulk materials. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Transient photoluminescence decay study of minority carrier lifetime in GaAs heteroface solar cell structures

Transient photoluminescence decay has been studied theoretically and experimentally as a technique for the investigation of GaAs solar cell materials and solar cell structures. The time-dependent continuity equation was solved using two variable boundary conditions modelling the interface between the emitter and hetero-window layer (AlGaAs) and between the emitter and space charge region, respectively. The solution was found with help of the Fourier transform method and the method of residues. There results an analytical expression for the time dependent photoluminescence (PL) intensity. The influence of various solar cell parameters on this photoluminescence transient has been studied in detail. An experimental investigation of transient PL decay was performed using a synchronously pumped mode locked and cavity dumped Nd:YAG/dye laser system for excitation and an optical sampling oscilloscope as the detector. GaAs wafers with and without surface passivation have been measured as well as hetero-window pn-structures and processed solar cells. A fit of the theoretical PL transients to the measured transients allows surface and bulk recombination parameters to be determined.Dedicated to H.-J. Queisser on the occasion of his 60th birthday     

一种印刷型薄膜太阳能电池p-n结调制技术

能带值为0.5~0.85 eV材料的稀缺是多结太阳能电池面临的一个主要挑战,本文使用非真空的机械化学法合成了能带值为0.83 eV的Cu₂SnS₃化合物,使用印刷技术将其制备成吸收层薄膜,并采用superstrate太阳能电池结构(Mo/Cu₂SnS₃/In₂S₃/TiO₂/FTO glass)对其光伏特性进行了研究.实验表明所制备的太阳能电池短路电流密度、开路电压、填充因子和转换效率分别为12.38 mA/cm²、320 mV、0.28和1.10%.此外,为更好地满足多结太阳能电池对电流匹配的需求,本文对所制备太阳能电池的Cu₂SnS₃/In₂S₃ p-n结进行了分析.通过在p-n结界面植入一层薄的疏松缓冲层,使调制后的太阳能电池短路电流密度从最初的12.38 mA/cm²增加到了23.15 mA/cm²,相应太阳能电池转换效率从1.1%增加到了1.92%.该p-n调制技术对印刷型薄膜太阳能电池具有重要借鉴意义.     

菲涅耳聚光系统下砷化镓电池输出特性研究

对理论聚光比为676的菲涅耳聚光系统下单片砷化镓太阳电池及由六片砷化镓电池的串联组件的输出特性进行分析。建立三结砷化镓电池输出特性的单指数数学模型,并与实验进行了对比。理论计算与实验吻合较好,误差在7.6%以内。实验结果表明,在相同理论聚光比下,单片电池系统能流聚光比为390,六片电池组件系统能流聚光比为281;聚光后单片电池的短路电流与峰值功率分别放大322倍与316倍,六片电池组件系统的短路电流与峰值功率分别放大275倍与272倍;电池表面能流密度为0.321MW/m2时电池的输出功率达到最大,电池表面温度高于323K将影响其工作稳定性;聚光系统的透射率每增加0.01系统效率升高约0.227%。全天累积直射辐照度为17.212MJ/m2条件下测得单片电池全天发电量为0.015kW.h,六片电池串联组件的全天发电量为0.076kW.h。     

基于阳极氧化铝纳米光栅的薄膜硅太阳能电池双重陷光结构设计与仿真

本文提出了表面和底部均带有阳极氧化铝(AAO)纳米光栅的薄膜硅太阳能电池双重陷光结构,利用FDTD软件仿真研究了AAO纳米光栅的周期、厚度和占空比对薄膜硅太阳能电池短路电流密度的影响,并对AAO结构参数进行了优化.仿真结果表明,表面AAO最佳结构参数是周期440 nm,厚度75 nm,占空比0.5,底部AAO最佳结构参数是周期380 nm,厚度90 nm,占空比为0.75.双重AAO组合陷光结构可有效增加薄膜硅太阳能电池在280—1100 nm范围内的光吸收,吸收相对增强可以达到74.44%.     

Delta-doped quantum wire tunnel junction for highly concentrated solar cells

We propose a novel structure for tunnel junction based on delta-doped AlGaAs/GaAs quantum wires. Higher spatial confinement of quantum wires alongside the increased effective doping concentration in the delta-doped regions extremely increase the peak tunneling current and enhance the performance of tunnel junction. The proposed structure can be used as tunnel junction in the multijunction solar cells under the highest possible thermodynamically limited solar concentration.The combination of the quantum wire with the delta-doped structure can be of benefit to the solar cells' advantages including higher number of sub-bands and high degeneracy. Simulation results show a voltage drop of 40 mV due to the proposed tunnel junction used in a multijunction solar cell which presents an extremely low resistance to the achieved peak tunneling current.     

InGaAs/GaAs单量子阱PL谱的温度变化特性

采用分子束外延方法制备了InGaAs/GaAs单量子阱,利用自组装的光致荧光探测系统,对其进行了光致荧光谱研究。考察了不同温度下荧光峰波长、峰形的影响。研究结果表明:高温时荧光主要是源于带—带间载流子跃迁,而在低温时则来源于束缚在量子阱中激子的跃迁。     

高温处理工艺对低压MOCVD外延GaAs/Ge太阳电池的影响

采用自制的低压金属有机化学汽相淀积LP-MOCVD设备,在Ge衬底(100)面向(111)偏9°外延生长出GaAs电池结构,对电池材料进行了X射线衍射分析另外,对由此材料制成的太阳电池进行了性能测试,测试结果表明,Ge衬底的高温处理工艺对GaAs/Ge太阳电池的电流电压特性有一定的影响试验表明,在600～700℃之间高温处理效果较好。     

Photoluminescence and lasing properties of InAs/GaAs quantum dots grown by metal-organic chemical vapour deposition

Photoluminescence （PL） and lasing properties of InAs/GaAs quantum dots （QDs） with different growth procedures prepared by metalorganic chemical vapour deposition are studied. PL measurements show that the low growth rate QD sample has a larger PL intensity and a narrower PL line width than the high growth rate sample. During rapid thermal annealing, however, the low growth rate sample shows a greater blueshift of PL peak wavelength. This is caused by the larger InAs layer thickness which results from the larger 2-3 dimensional transition critical layer thickness for the QDs in the low-growth-rate sample. A growth technique including growth interruption and in-situ annealing, named indium flush method, is used during the growth of GaAs cap layer, which can flatten the GaAs surface effectively. Though the method results in a blueshift of PL peak wavelength and a broadening of PL line width, it is essential for the fabrication of room temperature working QD lasers.     

直接键合的三结太阳能电池研究

本文研制了直接键合的三结GaInP/GaAs/InGaAsP太阳电池.直接键合技术可以减少晶格不匹配的材料在外延生长过程中产生的线位错和面缺陷,将缺陷限制在界面几十纳米的薄层而不向内扩散,是未来实现高效多结电池的发展趋势之一.此类电池国内鲜有报道.本文键合三结电池的键合界面采用p+GaAs/n+InP结构,得到电池开路电压3.0 V,在电池结构没有优化的情况下获得效率24%,表面未做减反膜.开路电压表明三结电池实现了串联,为单片集成的高效多结电池提供了新的途径.对实验结果进行了分析并给出了改进措施.     

Understanding the junction degradation mechanism in CdS/CdTe solar cells using a Cd-deficient CdTe layer

It is known that CdTe solar cells are often degraded under solar illumination. But the degradation mechanism is not fully proved because it does not appear consistently. The junction degradation in CdS/CdTe solar cells was investigated using a CdTe layer with Cd deficient composition, where Cd vacancy concentration is high. It was found that the Cu atoms easily filled the Cd vacancies in CdTe and transport to junction area from Cu back contact. PL measurement and spectral quantum efficiency measurement showed that the incorporation of Cu atoms in CdS forms a defect energy level at 1.55 eV below the conduction band in CdS. As a result, the junction built-in potential is decreased and light penetration into CdTe absorber is shielded. For reliable and stable CdTe cells, the formation of Cd vacancy in CdTe should be avoided by careful control of CdTe.     

Morphology and optical properties of p-type porous GaAs(1 0 0) layers made by electrochemical etching

Porous GaAs layers were formed by electrochemical etching of p-type GaAs(1 0 0) substrates in HF solution. A surface characterization has been performed on p-type GaAs samples using X-ray photoelectron spectroscopy (XPS) technique in order to get information about the chemical composition, particularly on the surface contamination. According to the XPS spectra, the oxide layer on as-received porous GaAs substrates contains As₂O₃, As₂O₅ and Ga₂O₃. Large amount of oxygen is present at the surface before the surface cleaning.Compared to untreated GaAs surface, room temperature photoluminescence (PL) investigations of the porous layers reveal the presence of two PL bands: a PL peak at ∼871 nm and a “visible” PL peak at ∼650-680 nm. Both peak wavelengths and intensities varied from sample to sample depending on the treatment that the samples have undergone. The short PL wavelength at 650-680 nm of the porous layers is attributed to quantum confinement effects in GaAs nano-crystallites. The surface morphology of porous GaAs has been studied using atomic force microscopy (AFM). Nano-sized crystallites were observed on the porous GaAs surface. An estimation of the mean size of the GaAs nano-crystals obtained from effective mass theory and based on PL data was close to the lowest value obtained from the AFM results.     

实用型三谱段太阳模拟器的设计与研制

本文设计并研制了一种实用型三谱段太阳模拟器,其光谱匹配可同时调整3个谱段(300~700 nm,700~900 nm,900~1 700 nm)范围的能量,修正后可满足三结砷化镓太阳电池的测试使用要求。本文重点阐述了三谱段太阳模拟器滤光片的设计和氙灯光谱的修正及测试,介绍了太阳模拟器的光机结构。实验表明:三谱段太阳模拟器的光谱匹配满足三结砷化镓太阳电池各子电池的响应电流值。在有效辐照面150 mm×150 mm上,平均辐照度可以达到2个太阳常数(2 730 W/m²),辐照不均匀度达到±1.77%,辐照不稳定度达到±0.83%,为太阳电池自动分拣系统提供了可靠稳定的平台。     

Preparation of pulse plated GaAs films

Thin GaAs films were prepared by pulse plating from an aqueous solution containing 0.20 M GaCl₃ and 0.15 M As₂O₃ at a pH of 2 and at room temperature. The current density was kept as 50 mA cm⁻² the duty cycle was varied in the range 10-50%. The films were deposited on titanium, nickel and tin oxide coated glass substrates. Films exhibited polycrystalline nature with peaks corresponding to single phase GaAs. Optical absorption measurements indicated a direct band gap of 1.40 eV. Photoelectrochemical cells were made using the films as photoelectrodes and graphite as counter electrode in 1 M polysulphide electrolyte. At 60 mW cm⁻² illumination, an open circuit voltage of 0.5 V and a short circuit current density of 5.0 mA cm⁻² were observed for the films deposited at a duty cycle of 50%.     

声表面波对GaAs(110)量子阱发光特性的调制

结合声表面波和光致发光谱在低温(15K)下对非故意掺杂的GaAs(110)量子阱结构的发光特性进行了研究.实验结果表明，由于声表面波的作用GaAs(110)量子阱的发光强度减弱,并且其对应的重空穴能级出现了分裂的现象，当施加的声波强度P_rf达到20dBm时，能级分裂ΔE达到了10meV.进一步讨论了声表面波对GaAs(110)量子阱圆偏振光自旋注入的影响. 关键词： 发光 GaAs量子阱 声表面波 自旋极化