Benzimidazolium-based new simple ratiometric fluorescent sensor for selective detection of dihydrogenphosphate

A series of pyridine-coupled benzimidazolium-based receptors 1, 2 and 3 have been designed and synthesised. In the series, only receptor 1 is structurally appealing in the selective recognition of H₂PO₄^?  in CHCl₃ as well as in CH₃CN over a series of other anions. The ratiometric change in emission with a triplet band at 420 nm is the distinctive feature of selective recognition of H₂PO₄^?  in CHCl₃. In CH₃CN, a ‘turn on’ response is selectively observed. Binding studies have been carried out using fluorescence, UV–vis, ¹H NMR and ³¹P NMR spectroscopic techniques. Experimental results have been correlated with the theoretical findings.     

A highly selective chemosensor for copper ion based on ICT fluorescence

Simple structural compounds 1 to 3 were synthesized.The presence of Cu²⁺ resulted in the fluorescence and absorption spectra change of 1 and 2,which indicated that 1 and 2 showed a highly selective response to Cu²⁺ over other metal ions.However,3 showed no selectivity for metal ions,which means that the compound could bind with several metal ions,such as,Ni²⁺,Zn²⁺,Cd²⁺.Hg²⁺, Pb²⁺,Fe³⁺,Mg²⁺,Ca²⁺,and Co²⁺,except Cu²⁺ and Ag⁺.The different spectral responses were attributed to the difference in binding sites for 1 and 3.     

A helical chiral polymer‐based chromo‐fluorescence and CD response sensor for selective detection of trivalent cations

A novel chiral (S)‐BINAM‐based fluorescent polymer sensor was designed and synthesized by the polymerization of 4,4′‐((2,5‐dibutoxy‐1,4‐phenylene)bis(ethyne‐2,1‐diyl))‐dibenzaldehyde ( M‐1 ) with (S)‐2,2′‐binaphthyldiamine (S‐BINAM, M‐2 ) via Schiff's base formation. The resulting helical chiral polymer sensor exhibited remarkable “turn‐on” bright blue fluorescence color upon the addition of trivalent metal ions under a commercially available UV lamp; this change can be clearly observed by the naked eye for direct visual discrimination at low concentration. More importantly, the addition of trivalent metal cations can lead to a most pronounced change of CD spectra of the chiral polymer indicating this kind chiral sensor can also be used as a sole probe for selective recognition of trivalent metal cations based on CD spectra. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4070–4075     

A fluorescence enhancement-based sensor for hydrogen sulfate ion

Sugar-aza-crown ether-based cavitand 1 can act as a selective turn-on fluorescence sensor for hydrogen sulfate ion in methanol among a series of tested anions. Spectroscopic studies, particularly NMR spectroscopy, revealed that the C-H hydrogen bonding between 1,2,3-triazole ring of cavitand 1 and hydrogen sulfate ion is crucial for the high selectivity of the receptor for hydrogen sulfate.     

A selective optical chemical sensor for o-nitrophenol based on fluorescence quenching of curcumin

An optical chemical sensor has been prepared for the selective determination of o-nitrophenol in aqueous solutions based on the fluorescence quenching of curcumin in PVC membrane. The sensing mechanism of the proposed sensor for o-nitrophenol has been discussed in detail. The fluorescence changes of sensing membrane resulted from an associated complex formation between curcumin and o-nitrophenol. In pH 4.8 buffer solution, the sensor responds linearly in the measuring range from 1.0 x 10(-2) mol 1(-1) to 1.5 x 10(-4) mol 1(-1), and the experimental detection limit is evaluated to be 8.0 x 10(-5) mol 1(-1). A stable signal was obtained within less than 1.5 min. Under the optimum conditions, the sequence of selective response to the sensing membrane is o-nitrophenol > 2,4-dinitrophenol > m-nitrophenol > p-nitrophenol > 2,4,6-trinitrophenol. Phenol, aniline as well as other ions have less effect on the fluorescence of the sensor. The reproducibility for the determination of o-nitrophenol is better than 1%, and the response is reversible. The sensor can be used for the determination of o-nitrophenol in water samples.     

A novel ion selective sensor for promethium determination

This is a first promethium(145) ion-selective sensor based on the comparative study of two Schiff base ligands (X(1) and X(2)) as neutral ionophores. Effect of various plasticizers: 2-nitrophenyloctylether (o-NPOE), dibutyl phosphonate (DBP), dioctylphthalate (DOP), tri-(2-ethylhexyl) phosphate (TEHP), dibutyl butylphosphonate (DBBP), chloronaphthalene (CN) and anion excluders: potassium tetrakis (p-chloropheny1) borate (KTpClPB), sodiumtetraphenylborate (NaTPB) and oleic acid (OA) have been studied. The membrane with a composition of ionophore (X(1)/X(2)):KTpClPB:PVC:o-NPOE (w/w, %) in the ratio of 5:5:30:60 exhibited best performance. The best responsive membrane sensors (8 and 21) exhibited working concentration range of 4.5×10(-7)-1.0×10(-2) M and 3.5×10(-6)-1.0×10(-2) M with a detection limits of 3.2×10(-7) M and 2.3×10(-6) M and Nernstian slopes of 20.0±0.5, 19.5±0.5 mV decade(-1) of activity, respectively. The sensor no. 8 works satisfactorily in partially non-aqueous media up to 10% (v/v) content of methanol, ethanol and acetonitrile. Analytical application of the proposed sensor has been demonstrated in determination of promethium (III) ions in spiked water samples.     

A turn-on and reversible fluorescence sensor for zinc ion

A simple Schiff base type fluorescent receptor was prepared and evaluated for its fluorescence response to heavy metal ions. Receptor exhibits an "off-on-type" mode with high selectivity in the presence of Zn(2+) ion. The addition of EDTA quenches the fluorescence of receptor -Zn(2+) complex, making receptor a reversible chemosensor. The selectivity of for Zn(2+) is the consequence of combined effects of CHEF, C[double bond, length as m-dash]N isomerization and inhibition of ESIPT.     

A turn-on Schiff base fluorescence sensor for zinc ion

A simple Schiff base type fluorescent receptor 1 was prepared and evaluated for its fluorescence response to heavy metal ions. Receptor 1 exhibits an ‘off-on-type’ mode with high selectivity in the presence of Zn²⁺ ion. The selectivity of 1 for Zn²⁺ is the consequence of combined effects of chelation-enhanced fluorescence (CHEF), CN isomerization, and inhibition of photoinduced electron transfer (PET).     

Selenodiazole-fused diacetamidopyrimidine, a selective fluorescence sensor for aliphatic monocarboxylates

A designed sensor, selenodiazole-fused pyrimidine ring having two acetylamino groups at 2,4-positions has been synthesized for selective recognition of aliphatic monocarboxylate anions over a wide range of other anions. The recognition study has been carried out by UV-vis and fluorescence methods. A significant bathochromic shift of the fluorescence intensity of the receptor in the presence of carboxylate makes the receptor a discriminating sensor for aliphatic monocarboxylates.     

Interaction between biphenols and anions: selective receptor for dihydrogenphosphate

Biphenol was shown to bind dihydrogenphosphate (H2PO4-) selectively over various other anions (MeCO2-, Cl-, Br-, I-, NO3-, HSO4-). The highly selectivity of biphenol toward dihydrogenphosphate is explained in terms of the basicity and shape of the guest anion.     

Pyridinium amide-based simple synthetic receptor for selective recognition of dihydrogenphosphate

A new fluorescent receptor 1 built on biphenyl motif has been designed and synthesized. Pyridinium amide moiety in 1 acts as binding site and shows selective complexation of isophthalate and under the mastery of biphenyl spacer. Binding-induced increase in emission was used to determine the selectivity and sensitivity of 1 toward a series of anions such as different dicarboxylates, , , and . The binding characteristics were established by ¹H NMR, UV-vis, and fluorescence spectroscopic methods.     

Highly selective tryptophan enantiomers electrochemical chiral sensor based on poly-lysine and functionalized multi-walled carbon nanotubes

Journal of Solid State Electrochemistry - A novel electrochemical chiral sensor was reported for recognizing tryptophan enantiomers based on multi-walled carbon nanotubes functionalized by...     

Solid-state ion selective electrode based on polypyrrole conducting polymer nanofilm as a new potentiometric sensor for Zn2+ ion

A pencil graphite electrode (PGE) electrodeposited by a polypyrrole conducting polymer doped with tartrazine (termed as PGE/PPy/Tar) was prepared and used as a zinc (II) solid-state ion-selective electrode. For the preparation of the zinc sensor electrode, electrodeposition of a polypyrrole nanofilm was carried out potentiostatically (E _app?=?0.75 V vs SCE) in a solution containing 0.010 M pyrrole and 0.001 M tartrazine trisodium salt. A pencil graphite and Pt wire were used as working and auxiliary electrodes, respectively. The introduced electrode in the current paper can be fabricated simply and was found to possess high selectivity, exhibited wide working concentration range, sufficiently rapid response, potential stability, and very good sensitivity to Zn (II) ion. The sensor electrode showed a linear Nernstian response over the range of 1.0?×?10^?5 to 1.0?×?10^?1 M with a slope of 28.23 mV per decade change in zinc ion concentration. A detection limit of 8.0?×?10^?6 M was obtained. The optimum pH working of the electrode was found to be 5.0.     

Fabrication of an electrochemical sensor based on spiropyran for sensitive and selective detection of fluoride ion

In the past decades, numerous electrochemical sensors based on exogenous electroactive substance have been reported. Due to non-specific interaction between the redox mediator and the target, the instability caused by false signal may not be avoided. To address this issue, in this paper, a new electrochemical sensor based on spiropyran skeleton, namely SPOSi, was designed for specific electrochemical response to fluoride ions (F⁻). The breakage of Si–O induced by F⁻ based on the specific nucleophilic substitution reaction between F⁻ and silica would directly produce a hydroquinone structure for electrochemical signal generation. To improve the sensitivity, SPOSi probe was assembled on the single-walled carbon nanotubes (SWCNTs) modified glassy carbon electrode (GCE) through the π–π conjugating interaction. This electrode was successfully applied to monitor F⁻ with a detection limit of 8.3 × 10⁻⁸ M. Compared with the conventional F⁻ ion selected electrode (ISE) which utilized noncovalent interaction, this method displays higher stability and a comparable sensitivity in the urine samples.     

Conducting polymer ion sensor electrodes-III. Potentiometric sulfide ion selective electrode

A new potentiometric sensor electrode for sulfide based on conducting polymer films is introduced. The electrode is formed by electrochemically depositing a film of poly(3-methylthiophene) and poly(dibenzo-18-crown-6) onto an alloy substrate. Different methods were used for the electrode preparations. The alloy used has a low melting point, which allowed its use for manufacturing a microsize version of this electrode. The electrode response is stable for 3 days. The working temperature range for this electrode is between 10 and 40 degrees C. The linear dynamic range is 1.0x10(-7)-1.0x10(-2) M and measures total sulfide concentration over a range of pH from 1 to 13. The polymer electrode showed high selectivity for sulfide in the presence of many common interfering anions. The electrode is useful for the measurement of total sulfide in biological environments and can be manufactured in the micron scale. Therefore, it will be useful for the measurement within biofilms.     

A selective optical chemical sensor for 2,6-dinitrophenol based on fluorescence quenching of a novel functional polymer

A bifurcated optical fiber based chemical sensor for continuous monitoring of 2,6-dinitrophenol (2,6-DNP) has been proposed based on the reversible chemical reaction between a novel functional poly(vinyl chloride) (PVC) as the sensing material and the analytes. The functional PVC (FPVC), containing a fluorescent curcumin moiety, was synthesized by the nucleophilic substitution of a fraction of the chlorine atoms bound to the PVC backbone by curcumin. When plasticized in a membrane of 5 μm thickness, FPVC extracts 2,6-DNP from aqueous solution into the bulk membrane phase and reacts with the analyte to form a complex with low fluorescence efficiency through hydrogen bonding. Formation of the complex gave a significant fluorescence quenching which is suitable for signalling the occurrence of the host-guest interaction. At pH 3.50, the sensor exhibits a dynamic detection range from 2.5 × 10⁻⁶ to 7.0 × 10⁻³ mol L⁻¹ with a limit of detection of 1.0 × 10⁻⁶ mol L⁻¹. As 2,6-DNP can provide an optimal space geometry matches to the formation of hydrogen bonds, the sensor shows excellent selectivity for 2,6-DNP over other nitrophenols. The forward and reverse response time (t₉₅) of the sensor both was within 1 min. The repeatability, reproducibility, and lifetime of the sensor were also satisfied. The sensor was applied to determine 2,6-DNP in water samples successfully.     

Preparation and application of a new glucose sensor based on iodide ion selective electrode

An electrode for glucose has been prepared by using an iodide selective electrode with the glucose oxidase enzyme. The iodide selective electrode used was prepared from 10% TDMAI and PVC according our previous study. The enzyme was immobilized on the iodide electrode by holding it at pH 7 phosphate buffer for 10 min at room temperature. The H₂O₂ formed from the reaction of glucose was determined from the decrease of iodide concentration that was present in the reaction cell. The iodide concentration was followed from the change of potential of iodide selective electrode. The potential change was linear in the 4×10⁻⁴ to 4×10⁻³ M glucose concentration (75-650 mg glucose/100ml blood) range. The slope of the linear portion was about 79 mV per decade change in glucose concentration. Glucose contents of some blood samples were determined with the new electrode and consistency was obtained with a colorimetric method. The effects of pH, iodide concentration, the amount of enzyme immobilized and the operating temperature were studied. No interference of ascorbic acid, uric acid, iron(III) and Cu(II) was observed. Since the iodide electrode used was not an AgI-Ag₂S electrode, there was no interference of common ions such as chloride present in biological fluids. The slope of the electrode did not change for about 65 days when used 3 times a day.     

A Zn(II) ion selective fluorescence sensor that is not affected by Cd(II)

Comparison of sensors sodium-2,6-diamino-(N,N,N′,N′-tetraacetate)-4-methylanisole 1 and sodium-2,6-diamino-(N,N,N′-triacetate)-4-methylanisole 2 reveal that the loss of an acetyl group in 2 leads to a more selective Zn(II) induced fluorescence enhancement and shows no response to any other metal ions including Cd(II). Structural modifications and AM1 calculations indicate that the sensor uses the three acetyl groups and the 3° amino nitrogen for binding the metal ion. AM1 calculations imply a trigonal bipyramidal coordination for Zn(II) with the solvent molecule occupying one of the axial positions.     

A highly selective turn-on ATP fluorescence sensor based on unmodified cysteamine capped CdS quantum dots

Unmodified cysteamine capped nanocrystalline cadmium sulfide quantum dots (Cys-CdS QDs) were demonstrated as a selective turn-on fluorescence sensor for sensing adenosine-5′-triphosphate (ATP) in aqueous solution for the first time. The fluorescence intensity of the Cys-CdS QDs was significantly enhanced in the presence of ATP. In addition, the fluorescence intensity of the Cys-CdS QDs increased when increasing ATP concentrations. On the other hand, other phosphate metabolites and other tested common anions did not significantly alter the fluorescence intensity of the Cys-CdS QDs. In addition, this sensor showed excellent discrimination of pyrophosphate (PPi) from ATP detection. The proposed sensor could efficiently be used for ATP sensing at very low concentration with LOD of 17 μM with the linear working concentration range of 20–80 μM. The feasibility of the proposed sensor for determining ATP in urine samples was also studied, and satisfactory results were obtained.     

Boron dipyrromethene fluorophore based fluorescence sensor for the selective imaging of Zn(II) in living cells

A simple PET fluorescence sensor (BDA) for Zn2+ that utilizes 1,3,5,7-tetramethyl-boron dipyrromethene as a reporting group and di(2-picolyl)amine as a chelator for Zn2+ has been synthesized and characterized. BDA has an excitation (491 nm) and emission wavelength (509 nm) in the visible range. The fluorescence quantum yields of the zinc-free and zinc-bound states of BDA are 0.077 and 0.857, respectively. With a low pKa of 2.1 +/- 0.1, BDA has the advantage of less sensitivity to pH than fluorescein-based Zn2+ sensors, and the fluorescence emission of zinc-binding is pH-independent in the range of pH 3-10. Under physiological conditions, metal ions such as Na+, K+, Ca2+, Mg2+, Mn2+ and Fe2+ have little interference. The apparent dissociation constant (Kd) is 1.0 +/- 0.1 nM. Using fluorescence microscopy, the sensor is shown to be capable of imaging intracellular Zn2+ changes.