An investigation on capability of hybrid Nd:YAG laser-TIG welding technology for AA2198 Al-Li alloy

This paper surveys the capability of the hybrid laser-arc welding in comparison with lone laser welding for AA2198 aluminum alloy experimentally. In the present research, a continuous Nd:YAG laser with a maximum power of 2000 W and a 350 A electric arc were used as two combined welding heat sources. In addition to the lone laser welding experiments, two strategies were examined for hybrid welding; the first one was low laser power (100 W) accompanied by high arc energy, and the second one was high laser power (2000 W) with low arc energy. Welding speed and arc current varied in the experiments. The influence of heat input on weld pool geometry was surveyed. The macrosection, microhardness profile and microstructure of the welded joints were studied and compared. The results indicated that in lone laser welding, conduction mode occurred and keyhole was not formed even in low welding speeds and thus the penetration depth was so low. It was also found that the second approach (high laser power accompanied with low arc energy) is superior to the first one (low laser power accompanied with high arc energy) in hybrid laser-arc welding of Al2198, since lower heat input was needed for full penetration weld and as a result a smaller HAZ was created.     

Optimization of laser butt welding parameters with multiple performance characteristics

This paper presents a study carried out on 3.5 kW cooled slab laser welding of 904 L super austenitic stainless steel. The joints have butts welded with different shielding gases, namely argon, helium and nitrogen, at a constant flow rate. Super austenitic stainless steel (SASS) normally contains high amount of Mo, Cr, Ni, N and Mn. The mechanical properties are controlled to obtain good welded joints. The quality of the joint is evaluated by studying the features of weld bead geometry, such as bead width (BW) and depth of penetration (DOP). In this paper, the tensile strength and bead profiles (BW and DOP) of laser welded butt joints made of AISI 904 L SASS are investigated. The Taguchi approach is used as a statistical design of experiment (DOE) technique for optimizing the selected welding parameters. Grey relational analysis and the desirability approach are applied to optimize the input parameters by considering multiple output variables simultaneously. Confirmation experiments have also been conducted for both of the analyses to validate the optimized parameters.     

Application of laser in seam welding of dissimilar steel to aluminium joints for thick structural components

Laser welding-brazing technique, using a continuous wave (CW) fibre laser with 8000 W of maximum power, was applied in conduction mode to join 2 mm thick steel (XF350) to 6 mm thick aluminium (AA5083-H22), in a lap joint configuration with steel on the top. The steel surface was irradiated by the laser and the heat was conducted through the steel plate to the steel-aluminium interface, where the aluminium melts and wets the steel surface. The welded samples were defect free and the weld micrographs revealed presence of a brittle intermetallic compounds (IMC) layer resulting from reaction of Fe and Al atoms. Energy Dispersive Spectroscopy (EDS) analysis indicated the stoichiometry of the IMC as Fe₂Al₅ and FeAl₃, the former with maximum microhardness measured of 1145 HV 0.025/10. The IMC layer thickness varied between 4 to 21 μm depending upon the laser processing parameters. The IMC layer showed an exponential growth pattern with the applied specific point energy (E_sp) at a constant power density (PD). Higher PD values accelerate the IMC layer growth. The mechanical shear strength showed a narrow band of variation in all the samples (with the maximum value registered at 31.3 kN), with a marginal increase in the applied E_sp. This could be explained by the fact that increasing the E_sp results into an increase in the wetting and thereby the bonded area in the steel-aluminium interface.     

Statistical modeling of laser welding of DP/TRIP steel sheets

In this research work, a statistical analysis of the CO₂ laser beam welding of dual phase (DP600)/transformation induced plasticity (TRIP700) steel sheets was done using response surface methodology. The analysis considered the effect of laser power (2–2.2 kW), welding speed (40–50 mm/s) and focus position (?1 to 0 mm) on the heat input, the weld bead geometry, uniaxial tensile strength, formability limited dome height and welding operation cost. The experimental design was based on Box–Behnken design using linear and quadratic polynomial equations for predicting the mathematical models. The results indicate that the proposed models predict the responses adequately within the limits of welding parameters being used and the welding speed is the most significant parameter during the welding process.     

Optimization of laser welding of DP/TRIP steel sheets using statistical approach

Generally, the quality of a weld joint is directly influenced by the welding input parameter settings. Selection of proper process parameters is important to obtain the desired weld bead profile and quality. In this research work, numerical and graphical optimization techniques of the CO₂ laser beam welding of dual phase (DP600)/transformation induced plasticity (TRIP700) steel sheets were carried out using response surface methodology (RSM) based on Box–Behnken design. The procedure was established to improve the weld quality, increase the productivity and minimize the total operation cost by considering the welding parameters range of laser power (2–2.2 kW), welding speed (40–50 mm/s) and focus position (?1 to 0 mm). It was found that, RSM can be considered as a powerful tool in experimental welding optimization, even when the experimenter does not have a model for the process. Strong, efficient and low cost weld joints could be achieved using the optimum welding conditions.     

Three-dimensional transient thermoelectric currents in deep penetration laser welding of austenite stainless steel

The existence of thermoelectric currents (TECs) in workpieces during the laser welding of metals has been common knowledge for more than 15 years. However, the time-dependent evolutions of TECs in laser welding remain unclear. The present study developed a novel three-dimensional theoretical model of thermoelectric phenomena in the fiber laser welding of austenite stainless steel and used it to observe the time-dependent evolutions of TECs for the first time. Our model includes the complex physical effects of thermal, electromagnetic, fluid and phase transformation dynamics occurring at the millimeter laser ablated zone, which allowed us to simulate the TEC, self-induced magnetic field, Lorentz force, keyhole and weld pool behaviors varying with the welding time for different parameters. We found that TECs are truly three-dimensional, time-dependent, and uneven with a maximum current density of around 10⁷ A/m² located at the liquid-solid (L/S) interface near the front or bottom part of the keyhole at a laser power of 1.5 kW and a welding speed of 3 m/min. The TEC formed three-dimensional circulations moving from the melting front to solidification front in the solid part of workpiece, after which the contrary direction was followed in the liquid part. High frequency oscillation characteristics (2.2–8.5 kHz) were demonstrated in the TEC, which coincides with that of the keyhole instability (2.0–5.0 kHz). The magnitude of the self-induced magnetic field and Lorentz force can reach 0.1 mT and 1 kN/m³, respectively, which are both consistent with literature data. The predicted results of the weld dimensions by the proposed model agree well with the experimental results. Our findings could enhance the fundamental understanding of thermoelectric phenomena in laser welding.     

Parametric optimisation and microstructural analysis on high power Yb-fibre laser welding of Ti–6Al–4V

In this work thin sheets of Ti–6Al–4V were full penetration welded using a 5 kW fibre laser in order to evaluate the effectiveness of high power fibre laser as a welding processing tool for welding Ti–6Al–4V with the requirements of the aircraft industry and to determine the effect of welding parameters including laser power, welding speed and beam focal position on the weld microstructure, bead profile and weld quality. It involved establishing an understanding of the influence of welding parameters on microstructural change, welding defects, and the characteristics of heat affected zone (HAZ) and weld metal (WM) of fibre laser welded joints. The optimum range of welding parameters which produced welds without cracking and porosity were identified. The influence of the welding parameters on the weld joint heterogeneity was characterised by conducting detailed microstructural analysis.     

Ultrasonic-promoted rapid TLP bonding of fine-grained 7034 high strength aluminum alloys

High strength aluminum alloys are extremely sensitive to the thermal cycle of welding. An ultrasonic-promoted rapid TLP bonding with an interlayer of pure Zn was developed to join fine-grained 7034 aluminum alloys at the temperature of lower 400 °C. The oxide film could be successfully removed with the ultrasonic vibration, and the Al-Zn eutectic liquid phase generated once Al and Zn contacted with each other. Longer ultrasonic time can promote the diffusion of Zn into the base metal, which would shorten the holding time to complete isothermal solidification. The joints with the full solid solution of α-Al can be realized with the ultrasonic action time of 60 s and holding time of only 3 min at 400 °C, and the shear strength of joints could reach 223 MPa. The joint formation mechanism and effects of ultrasounds were discussed in details.     

Experimental investigation and metallographic characterization of fiber laser beam welding of Ti-6Al-4V alloy using response surface method

In the present study, experimental investigations of fiber-laser-beam-welding of 5 mm thick Ti-6Al-4V alloy are carried out based on statistical design of experiments. The relationship between the process parameters such as welding power, welding speed, and defocused position of the laser beam with the output responses such as width of the fusion zone, size of the heat affected zone, and fusion zone area are established in terms of regression models. Also, the most significant process parameters and their optimum ranges are identified and their percentage contributions on output responses are calculated. It is observed that welding power and speed plays the major role for full penetration welding. Also, welding power shows direct effect whereas welding speed shows the inverse effect on the output responses. The bead geometry is influenced by the defocused position of the laser beam due to the change in power density on the workpiece surface. However, overall fusion zone area is unaffected. Mechanical characterization of the welded samples such as microstructural analysis, hardness, and tensile tests are conducted. It is noticed that the hardness value of the FZ is higher than the HAZ and BM zone due to the difference in cooling rate during welding which promotes the formation of α′ martensitic phase in the FZ. Also, an average hardness value in the FZ is compared for two different defocusing positions (i.e. 1 and 2 mm). It is found that hardness value is higher for 1 mm defocused position than 2 mm due the decrement in grain size below a critical range at 2 mm defocused position. The ultimate tensile strength and % elongation of the welded samples are degraded as compared to BM which can be further improved by post heat treatment.     

Effect of ultrasonic vibration time on the Cu/Sn-Ag-Cu/Cu joint soldered by low-power-high-frequency ultrasonic-assisted reflow soldering

Techniques to improve solder joint reliability have been the recent research focus in the electronic packaging industry. In this study, Cu/SAC305/Cu solder joints were fabricated using a low-power high-frequency ultrasonic-assisted reflow soldering approach where non-ultrasonic-treated samples were served as control sample. The effect of ultrasonic vibration (USV) time (within 6 s) on the solder joint properties was characterized systematically. Results showed that the solder matrix microstructure was refined at 1.5 s of USV, but coarsen when the USV time reached 3 s and above. The solder matrix hardness increased when the solder matrix was refined, but decreased when the solder matrix coarsened. The interfacial intermetallic compound (IMC) layer thickness was found to decrease with increasing USV time, except for the USV-treated sample with 1.5 s. This is attributed to the insufficient USV time during the reflow stage and consequently accelerated the Cu dissolution at the joint interface during the post-ultrasonic reflow stage. All the USV-treated samples possessed higher shear strength than the control sample due to the USV-induced-degassing effect. The shear strength of the USV-treated sample with 6 s was the lowest among the USV-treated samples due to the formation of plate-like Ag₃Sn that may act as the crack initiation site.     

Welding of polymers using a 2 μm thulium fiber laser

Absorber-free transmission and butt-welding of different polymers were performed using thulium fiber laser radiation at the wavelength 2 μm. The relations between the laser process conditions and the dimensions and quality of the seam were investigated by means of optical and phase-contrast microscopy. Mechanical properties of the weld joints were studied in tensile strength tests. Laser-welded polyethylene samples revealed a tensile strength of greater than 80% of the bulk material strength. Transmission welding of different polymer combinations featured the formation of different joint classes depending on the spectral properties. The experiments demonstrate new application areas of mid-IR fiber laser sources for materials processing.     

Optimization of weld bead geometry in laser welding with filler wire process using Taguchi’s approach

In the present work, laser welding with filler wire was successfully applied to joining a new-type Al–Mg alloy. Welding parameters of laser power, welding speed and wire feed rate were carefully selected with the objective of producing a weld joint with the minimum weld bead width and the fusion zone area. Taguchi approach was used as a statistical design of experimental technique for optimizing the selected welding parameters. From the experimental results, it is found that the effect of welding parameters on the welding quality decreased in the order of welding speed, wire feed rate, and laser power. The optimal combination of welding parameters is the laser power of 2.4 kW, welding speed of 3 m/min and the wire feed rate of 2 m/min. Verification experiments have also been conducted to validate the optimized parameters.     

Stability information in plasma image of high-power CO2 laser welding

In deep penetration laser welding, a capillary called keyhole is formed when the energy intensity reaches 10⁶ W/cm². During this process, the vaporized metal and the surrounding atmosphere can be ionized to form plasma both in and above the keyhole. The stability of the keyhole has an important influence on the properties of welded components and the fluctuations of plasma. In this paper, a method was developed to acquire the stability information from plasma images taken by high-speed photography. The influences of surface impurity and the flowrate of side-assist gas on the stability were investigated. Bead-on-plate welding was performed on 12 mm E-grade shipbuilding steel plates using a 15 kW CO₂ laser, with helium as the blowing gas. Three characteristic parameters were used to evaluate the stability. It was found that these three characteristic parameters can effectively indicate the stability variation caused by the surface impurity and gas flowrate. The present research provides important insights into developing image-based sensors to monitor the welding process.     

Experimental design approach to the process parameter optimization for laser welding of martensitic stainless steels in a constrained overlap configuration

This paper presents an experimental design approach to process parameter optimization for the laser welding of martensitic AISI 416 and AISI 440FSe stainless steels in a constrained overlap configuration in which outer shell was 0.55 mm thick. To determine the optimal laser-welding parameters, a set of mathematical models were developed relating welding parameters to each of the weld characteristics. These were validated both statistically and experimentally. The quality criteria set for the weld to determine optimal parameters were the minimization of weld width and the maximization of weld penetration depth, resistance length and shearing force. Laser power and welding speed in the range 855–930 W and 4.50–4.65 m/min, respectively, with a fiber diameter of 300 μm were identified as the optimal set of process parameters. However, the laser power and welding speed can be reduced to 800–840 W and increased to 4.75–5.37 m/min, respectively, to obtain stronger and better welds.     

Laser-driven flyer application in thin film dissimilar materials welding and spalling

This paper applied a low cost method to pack and drive laser-driven flyer in the applications of welding and spalling. The laser system has the maximum energy of 3.1 J, which is much lower than that used in the previous study. The chemical release energy from the ablative layer was estimated as 3.7 J. The flying characteristic of laser-driven flyer was studied by measuring the flyer velocity at different locations with photonic Doppler velocimetry (PDV). The application of laser-driven flyer in welding Al and Cu was investigated at different laser spot size. Weld strength was measured with the peel test. Weld interface was characterized with optical microscopy (OM) and scanning electron microscopy (SEM). The study of application of laser-driven flyer in spalling was carried out for both brittle and ductile materials. The impact pressure was calculated based on the Hugoniot data. The amount of spalling was not only related to the impact pressure but also related to the duration of impact pressure. The fractography of spalled fracture surface was studied and revealed that the fracture mode was related to the strain rate. The spall strength of Cu 110, Al 1100 and Ni 201was measured and was consistent with the literature data.     

Ultrashort pulse laser micro-welding of cyclo-olefin copolymers

We report on the joining of transparent thermoplastic polymers using infrared femtosecond laser pulses. Due to nonlinear absorption, the developed micro-welding process for cyclo-olefin copolymers does not require any intermediate absorbing layers or any surface pre-processing of the welding partners. In view of an optimized and stable micro-welding process, the influence of the welding speed and focal position on both, the quality and shear force strength are investigated. We highlight that welding seam widths of down to 65 µm are feasible for welding speeds of up to 75 mm/s. However, a variation of the welding speed affects the required focal position for a successful joining process. The shear force strength of the welding seam is determined to 37 MPa, which corresponds to 64% of the shear strength of the bulk material and is not affected by the welding speed.     

Spatiotemporal propagation characteristics based on the exact solutions of the generalized nonlinear Schrödinger equation by intensity moments

Based on the exact solutions of the (3 + 1)-dimensional ((3 + 1)D) generalized nonlinear Schrödinger equation (GNLSE), we analyze the spatiotemporal propagation characteristics by intensity moments when a laser propagates in an inhomogeneous nonlinear medium. The different order intensity moment can describe the characteristics of a laser, and in the paper, the beam width (BW), the pulse width (PW), the skewness and the kurtosis parameter are calculated. The spatiotemporal propagation stability of the exact solutions is analyzed in detail by the second-order intensity moment. We find that when the diffraction and dispersion coefficients are the identical distributed functions, the BW and PW of the exact solutions are constants or vary periodically during nonlinear propagation. So, the spatiotemporal propagation of the exact solutions is stable. When the diffraction and dispersion coefficients are other coefficients, the BW and PW of the exact solutions vary irregularly due to the effect of a chirp. Thus the spatiotemporal propagation of the exact solutions is unstable. The results are helpful to the extendable investigation of nonlinear propagation and control of a laser pulse.     

Use of thermal imaging to characterize laser light reflection from thermoplastics as a function of thickness,laser incidence angle and surface roughness

Laser light reflection during the laser transmission welding (LTW) of thermoplastics has the potential to overheat and/or cause unintentional welding of adjacent features of the part being welded. For this reason, and in order to assess how much light is being absorbed by the transparent part (after measurement of the light transmitted through the transparent part), it is important to be able to quantify the magnitude and distribution of reflected light. The magnitude and distribution of the reflected light depends on the total laser input power as well as its distribution, the laser incidence angle (angle between the normal to the transparent part surface and the laser beam), the laser light polarization as well as the surface and optical properties of the transparent part. A novel technique based on thermal imaging of the reflected light was previously developed by the authors. It is used in this study to characterize the magnitude and distribution of reflected light from thermoplastics as a function of thickness (1–3.1 mm), laser incidence angle (20–40°) and surface roughness (0.04–1.04 μm). Results from reflection tests on nearly polished nylon 6 (surface roughness between 0.04 and 0.05 μm) have shown that, for the various thicknesses tested (1–3.1 mm), the total reflection was larger than the specular top surface reflection predicted via the Fresnel relation. From these observations, it is conjectured that, in addition to top surface reflection, the bulk and/or bottom surface also contribute to the total reflection. The results also showed that reflection decreased slightly with increasing thickness. As expected, for the p-polarized light used in this study, the reflection decreased with increasing angle of incidence for the range of angles studied. It was also found that when the surface roughness was close to zero and when it was close to the wavelength of the input laser beam (i.e. 940 nm), the reflectance values were close and reached a minimum between these two roughness values.     

Band offsets at ZnO/SiC heterojunction: Heterointerface in band alignment

Pulsed laser deposited ZnO layers on 6H-SiC substrates showed the six-fold symmetry, indicating a two-dimensional epitaxial growth mode. X-ray photoelectron spectroscopy was employed to study the valence band discontinuity and interface formation in the ZnO/6H-SiC heterojunction. The valence band offset was measured to be 1.38 ± 0.28 eV, leading to a conduction band offset value of 1.01 ± 0.28 eV. The resulting band lineup in epitaxial ZnO/6H-SiC heterojunction is determined to be of staggered-type alignment.     

Weld-bead profile and costs optimisation of the CO2 dissimilar laser welding process of low carbon steel and austenitic steel AISI316

The dissimilar full depth laser-butt welding of low carbon steel and austenitic steel AISI 316 was investigated using CW 1.5 kW CO₂ laser. The effect of laser power (1.1–1.43 kW), welding speed (25–75 cm/min) and focal point position (?0.8 to ?0.2 mm) on the weld-bead geometry (i.e. weld-bead area, A; upper width, W_u; lower width, W_l and middle width, W_m) and on the operating cost C was investigated using response surface methodology (RSM). The experimental plan was based on Box–Behnken design; linear and quadratic polynomial equations for predicting the weld-bead widthness references were developed. The results indicate that the proposed models predict the responses adequately within the limits of welding parameters being used. The regression equations were used to find optimum welding conditions for the desired geometric criteria.