Highly efficient and stable organic light-emitting diodes employing MoO3-doped perylene-3, 4, 9, 10-tetracarboxylic dianhydride as hole injection layer

We report highly efficient and stable organic light-emitting diodes (OLEDs) with MoO₃-doped perylene-3, 4, 9, 10-tetracarboxylic dianhydride (PTCDA) as hole injection layer (HIL). A green OLED with structure of ITO/20 wt% MoO₃: PTCDA/NPB/Alq₃/LiF/Al shows a long lifetime of 1012 h at the initial luminance of 2000 cd/m², which is 1.3 times more stable than that of the device with MoO₃ as HIL. The current efficiency of 4.7 cd/A and power efficiency of 3.7 lm/W at about 100 cd/m² have been obtained. The charge transfer complex between PTCDA and MoO₃ plays a decisive role in improving the performance of OLEDs.     

Tandem organic light-emitting diode with molybdenum tri-oxide thin film interconnector layer

A 10-nm thickness molybdenum tri-oxide (MoO₃) thin film was used as the interconnector layer in tandem organic light-emitting devices (OLEDs). The tandem OLEDs with two identical emissive units consisting of N,N'-bis(naphthalen-1-yl)-N,N'-bis(phenyl)-benzidine (NPB)/tris(8-hydroxyquinoline) aluminum (Alq₃) exhibited current efficiency-current density characteristics superior to the conventional single-unit devices. At 20 mA/cm², the current efficiency of the tandem OLEDs using the interconnector layers of MoO₃ thin film was about 4.0 cd/A, which is about twice of that of the corresponding conventional single-unit device (1.8 cd/A). The tandem OLED showed a higher power efficiency than the conventional single-unit device for luminance over 1200 cd/m². The experimental results demonstrated that a MoO₃ thin film with a proper thickness can be used as an effective interconnector layer in tandem OLEDs. Such an interconnector layer can be easily fabricated by simple thermal evaporation, greatly simplifying the device processing and fabrication processes required by previously reported interconnector layers. A possible explanation was proposed for the carrier generation of the MoO₃ interconnector layer.     

Enhanced power efficiency for white OLED with MoO3 as hole injection layer and optimized charge balance

White OLEDs with a different hole injection layer (MoO₃ or m-MTDATA), and a different electron transport layer (Alq₃ or Bphen) have been investigated. With 9,10-bis (2-naphthyl)-2-t-butylanthracene (TBADN) doped with 3% P-bis (P-N, N-diphenyl-aminostyryl) benzene (DSA-ph) and 0.05% 4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7,-tetramethyl-julolidy-9-enyl)-4H-pyran (DCJTB) as white emitting layer, the MoO₃/ /Bphen based device shows the lowest driving voltage and highest power efficiency among the referenced devices. At the current density of 20 mA/cm², its driving voltage and power efficiency are 5.43 V and 4.54 lm/W respectively, which is independently reduced 40% and improved 57% compared with those of the m-MTDATA/ / Alq₃ based one, respectively. The energy level diagram of the devices and single-carrier devices are studied to explain the reasons for the improvement. The results strongly indicate that carrier injection ability and balance shows a key significance in OLED performance.     

Highly efficient bipolar connecting layers for tandem organic light-emitting devices

A highly efficient tandem organic light-emitting device (OLED) has been fabricated by using an effective bipolar connecting layer structure. The connecting layers were made up of a layer of magnesium (Mg): 2,7-dipyrenyl-9,9-diphenyl fluorene (N-DPF) and a layer of tungsten trioxide (WO₃). Such a connecting layer structure permits efficient opposite holes and electrons flowing into two adjacent emitting units. The current efficiency of the two-unit tandem device can be dramatically enhanced by more than four times compared with that of the conventional single-unit device. At 60 mA/cm², the current efficiency of the tandem OLED using the connecting layers of Mg: N-DPF/WO₃ was about 8.15 cd/A. The results can be marked as a breakthrough approach to improve the current efficiency and brightness of OLEDs. Furthermore, a model of the carrier tunneling into light-emitting units is proposed based on carrier balance and field-assisted tunneling. It indicates that the connecting layer structure functions as the origin of high efficiency for the tandem OLEDs.     

基于新型电荷生成层的P-i-N结构白色有机叠层电致发光器件

采用2,9-Dimethyl-4,7-diphenyl-1,10-phenanthroline(BCP): 5 wt.% cesium carbonate(Cs₂CO₃)和N, N'-Bis(naphthalen-1-yl)-N,N'-bis(phenyl)-benzidine(NPB): 20 wt.% molybdenum oxide(MoO₃)分别作为器件的电子注入层和空穴注入层,研究了N型和P-i-N结构有机电致发光器件的载流子传输特性.载流子传输层中BCP: Cs₂CO₃和NPB:MoO₃的引入有效增强了载流子注入能力,从而降低了器件的驱动电压.基于新型电荷生成层BCP: 5 wt.% Cs₂CO₃/ NPB: 20 wt.% MoO₃制备了色稳定、高效率P-i-N结构有机叠层器件.与单元器件相比,引入新电荷生成层有机叠层器件的最大电流效率增大了2.5倍,表明该电荷生成层可以有效地将电子和空穴分别注入到相邻发光单元中.采用该电荷生成层制备了P-i-N结构白色有机叠层器件,器件的上下发光单元分别为橙光和蓝光发射.当发光亮度从500增加到5 000 cd/m²时,器件的色坐标稳定在(0.33, 0.29)附近,接近白光等能点.利用单色发光单元堆叠制备白色有机叠层器件的方法为实现色稳定、高效率的白色有机电致发光器件提供了一种有效的途径.     

Effect of SiO2/Si3N4 dielectric distributed Bragg reflectors (DDBRs) for Alq3/NPB thin-film resonant cavity organic light emitting diodes

In this article, we report on the effect of SiO₂/Si₃N₄ dielectric distributed Bragg reflectors (DDBRs) for Alq₃/NPB thin-film resonant cavity organic light emitting diode (RCOLED) in increasing the light output intensity and reducing the linewidth of spontaneous emission spectrum. The optimum DDBR number is found as 3 pairs. The device performance will be bad by further increasing or decreasing the number of DDBR. As compared to the conventional Alq₃/NPB thin-film organic light emitting diode (OLED), the Alq₃/NPB thin-film RCOLED with 3-pair DDBRs has the superior electrical and optical characteristics including a forward voltage of 6 V, a current efficiency of 3.4 cd/A, a luminance of 2715 cd/m² under the injection current density of 1000 A/m², and a full width at half maximum (FWHM) of 12 nm for emission spectrum over the 5-9 V bias range. These results represent that the Alq₃/NPB thin-film OLED with DDBRs shows a potential as the light source for plastic optical fiber (POF) communication system.     

Low driving voltage in organic light-emitting diode using MoO3/NPB multiple quantum well structure in hole transport layer

Driving voltage of organic light-emitting diode (OLED) is lowered by employing molybdenum trioxide (MoO₃)/N, N'-bis(naphthalene-1-yl)-N,N'-bis(phe-nyl)-benzidine (NPB) multiple quantum well (MQW) structure in hole transport layer. For the device with double quantum well (DQW) structure of ITO/ [MoO₃ (2.5 nm)/NPB (20 nm)]₂/Alq₃(50 nm)/LiF (0.8 nm)/Al (120 nm)], the turn-on voltage is reduced to 2.8 V, which is lowered by 0.4 V compared with that of the control device (without MQW structures), the driving voltage is 5.6 V, which is reduced by 1 V compared with that of the control device at the 1000 cd/m². In this work, the enhancement of the injection and transport ability for holes could reduce the driving voltage for the device with MQW structure, which is attributed not only to the reducing energy barrier between ITO and NPB, but also to the forming charge transfer complex between MoO₃ and NPB induced by the interfacial doping effect of MoO₃.     

Blue organic light-emitting diodes with low driving voltage and maximum enhanced power efficiency based on buffer layer MoO3

Blue organic light-emitting devices based on wide bandgap host material, 2-(t-butyl)-9, 10-di-(2-naphthyl) anthracene (TBADN), blue fluorescent styrylamine dopant, p-bis(p-N,N-diphenyl-amino-styryl)benzene (DSA-Ph) have been realized by using molybdenum oxide (MoO₃) as a buffer layer and 4,7-diphenyl-1,10-phenanthroline (BPhen) as the ETL. The typical device structure used was glass substrate/ITO/MoO₃ (5 nm)/NPB (30 nm)/[TBADN: DSA-Ph (3 wt%)](35 nm)/BPhen (12 nm)/LiF (0.8 nm)/Al (100 nm). It was found that the MoO₃∥BPhen-based device shows the lowest driving voltage and highest power efficiency among the referenced devices. At the current density of 20 mA/cm², its driving voltage and power efficiency are 5.4 V and 4.7 Lm/W, respectively, which is independently reduced 46%, and improved 74% compared with those the m-MTDATA∥Alq₃ is based on, respectively. The J-V curves of ‘hole-only’ devices reveal that a small hole injection barrier between MoO₃∥NPB leads to a strong hole injection, resulting low driving voltage and high power efficiency. The results strongly indicate that carrier injection ability and balance shows a key significance in OLED performance.     

基于铱配合物材料的高效高稳定性有机发光二极管

使用基于重金属Ir的新磷光材料(tpbi)₂Ir(acac)，制备了多层结构有机发光二极管器件: ITO/CuPc (40 nm)/α-NPD (45 nm)/CBP: (tpbi)₂Ir(acac) (3%, 30nm)/BCP(20 nm)/Alq₃ (20 nm)/LiF (1 nm)/Al (100 nm).测试了材料的寿命、光谱吸收性质和器件的I-V-L特性.器件在低电压下电流符合热发射注入模型，高电压下I-V呈线形关系.不同偏压下器件发光光谱稳定，多峰拟合结果表明器件光谱由α-NPD发光峰(450 nm)，(tpbi)₂Ir(acac)主发光峰(518 nm)和肩峰(543 nm)构成.驱动电压为6 V时，器件效率达到最大12.1 lm/W，此时亮度为136 cd/m²，器件亮度最大为13500 cd/m²，此时效率为0.584 lm/W. 关键词： 有机发光二极管 磷光 效率 I-V-L特性')" href="#">I-V-L特性 光谱     

Efficiency control of organic light-emitting diode for high contrast ratio performance in active matrix display applications

We demonstrate the possibility of controlling organic light-emitting diodes (OLEDs) efficiency with an optimized hole-delay layer (HDL) in order to achieve very high contrast ratio needed for active matrix display applications. No triplet exciton confinement structure and a molybdenum trioxide (MoO₃) HDL at ITO/hole transport layer interface were used for a careful placing and adjusting of the exciton recombination zone. An optimized thickness of 50 nm thick MoO₃ allows to cut off the efficiency at the black level of active matrix driving mode while it gets greater at higher luminance at high current density region over 20 mA/cm² compared to conventional device. Our suggested efficiency control way is believed to be very useful to future active matrix OLED displays.     

室温下磁场对基于Alq3的有机电致发光器件的影响

制备了ITO/NPB/LiF/Alq₃/LiF/Al的器件,测量了该组器件效率和亮度的磁效应.结果表明,在50 mT磁场中,当LiF缓冲层厚度为0.8 nm时,器件的效率最大增加了12.4%,磁致亮度最大变化率17%.同时,制备的磷光器件ITO/NPB/LiF/CBP:6 wt% Ir(ppy)₃/BCP/Alq₃/ LiF/Al,在50mT磁场作用下,当LiF缓冲层的厚度为0.8 nm时,器件的效率最大增加12.1%.在Alq_{3 关键词： 有机发光 磁场 效率 磁致亮度}     

Mixed-ligand Al complex—a new approach for more high efficient OLEDs

The mixed-ligand Aluminum bis(8-hydroxyquinoline) acetylacetonate (Alq₂Acac) complex was presented and its performance as electroluminescent and electron transporting layer for OLED was studied. The photophysical properties of the novel complex were investigated and compared with the properties of the parent Alq₃. Highly efficient OLED based on the mixed-ligand Al complex was developed with two times higher luminescence and efficiency compared to the identical OLED based on the conventional Alq₃ The better performance of the devices make the novel Al complex a very promising material for OLEDs.     

A comparative study of electrode effects on the electrical and luminescent characteristics of Alq3/TPD OLED: Improvements due to conductive polymer (PEDOT) anode

The performance of organic light emitting device (OLED) structures, based on identically fabricated Alq₃/TPD active regions, with various anode and cathode electrode structures are compared, and performance differences related to the different anode structure. The best performance was achieved with a conductive polymer, 3,4-polyethylenedioxythiopene-polystyrenesultonate (PEDOT), used as an anode layer, yielding a brightness of 1720 cd/m² at 25 V, a turn-on voltage of 3 V, and electroluminescence (EL) efficiency and external quantum efficiency of 8.2 cd/A and 2%, respectively, at a brightness of 100 cd/m² and 5 V. Compared to a baseline device (TPD/Alq₃/Al), PEDOT anodes substantially reduce the turn-on voltage and made current injection almost linear after turn-on, whiles devices incorporating a LiF and CuPc layers significantly improved device efficiency while slightly improving turn-on voltage and maintaining superlinear I-V injection. This is attributed to the reduced barrier at the organic-organic interface in PEDOT, the ‘ladder’ effect of stepping the band offset over several interfaces, and the favorable PEDOT film morphology. The benefit of the PEDOT anode is clearly seen in the improvement in device brightness and the high external quantum efficiency obtained.     

Highly efficient and stable organic light-emitting diode by balancing drift current of charge

Highly efficient and stable OLED device in which hole-drift current and electron-drift current are balanced was fabricated. Drift current characteristics according to the thickness of organic layer were examined using the device with ITO/m-MTDATA/NPB/Al structure that can only move the hole and the device with Al/LiF/Alq₃/LiF/Al structure that can only move the electron. Using the result of such examination, green device with balanced drift current was produced. Device with the structure of m-MTDATA (80 nm)/NPB (20 nm)/C-545T (3%) doped Alq₃ (5 nm)/Alq₃ (59 nm)/LiF (1 nm)/Al (200 nm) showed color purity of (0.309, 0.643) and high efficiency of 7.0 lm/W (14.4 cd/A). Most of light emission was observed inside the green emitting layer. Through the result of EL spectrum for the device also including red emitting layer, same result could be obtained. The device with balanced drift current also showed half life-time of 175 h for initial luminance of 3000 cd/m², which is more stable in comparison to the device without balanced drift current.     

1.53 μm electroluminescence from ErF3-doped organic light-emitting diodes

Near-infrared (NIR) organic light-emitting devices (OLEDs) are demonstrated by employing erbium fluoride (ErF₃)-doped tris-(8-hydroxyquinoline) aluminum (Alq₃) as the emitting layer. The device structure is ITO/N,N′-di-1-naphthyl-N,N′-diphenylbenzidine (NPB)/Alq₃: ErF₃/2,2′,2″-(1,3,5-phenylene)tris(1-phenyl-1H-benzimidazole) (TPBI)/Alq₃/Al. Room-temperature electroluminescence around 1530 nm is observed due to the ⁴I_13/2–⁴I_15/2 transition of Er³⁺. Full width at half maximum (FWHM) of the electroluminescent (EL) spectrum is ～50 nm. NIR EL intensity from the ErF₃-based device is ～4 times higher than that of Er(DBM)₃Phen-based device at the same current. Alq₃–ErF₃ composite films are investigated by the measurements of X-ray diffraction (XRD), absorption, photoluminescence (PL) and PL decay time. Electron-only devices are also fabricated. The results indicate that energy transfer mechanism and charge trapping mechanism coexist in the NIR EL process.     

Emission properties of dopants rubrene and coumarin 6 in Alq3 films

We have investigated the emission properties of dopants 5,6,11,12-tetraphenylnapthacene (rubrene) and 3-(2′-benzothiazolyl)-7-diethylaminocoumarin (coumarin 6) as well as co-doping of these two dopants in tris (8-hydroxyquinolinato) aluminum (Alq₃) films in double-layer organic light emitting diodes (OLEDs). We varied the rubrene (Rb) doping concentration in Alq₃:Rb films up to 10 wt%. The maximum luminescence efficiency of ∼6.5 cd/A was observed for Rb doping concentration of ∼0.7 wt% in Alq₃:Rb film, which was nearly double efficiency compared to pure Alq₃ device. The co-doping of dopants of C-6 and Rb in the ratio of 1:1 and 1:2 in Alq₃ films reduced the bias voltage compared to pure Alq₃ and Alq₃:C-6 devices for the same current density. The maximum luminescence efficiency was improved to ∼7 cd/A in Alq₃:{C-6:Rb(1:2)} film OLED. The direct recombination of holes and electrons in the dopant molecules may be responsible for the improvement of the luminescence efficiency. We also observed the shifting of photoluminescence (PL) and electroluminescence (EL) peaks position from ∼515 to ∼562 nm by co-doping of Rb and C-6 in Alq₃.     

Pure red emission of dye-doped organic molecules from microcavity organic light emitting diode

Organic red emitting diode was fabricated by using 4-dicyanomethylene-2-methyl-6-[2-(2,3,6,7-tetrahydro-1 H,5H-benzo[ij]quinolizin-8-yl)vinyl]-4H-pyran (DCM)-doped tri-(8-quinolitolato) aluminum (Alq₃) as emitter with the structure of G/ITO/NPB(25 nm)/DCM:Alq₃(55 nm)/Alq₃(20 nm)/LiF (1.2 nm)/Al(84 nm), (glass/indium–tin-oxide/4,4-bis-[N-(1-naphthyl)-N-phenyl-amino]biphenyl, G/ITO/NPB), the wavelength of the maximal emission of which is 615 nm. By introducing cavity to Organic light emitting diode (OLED), we got pure red emitting diode with wavelength of the maximal emission of 621 nm and full-width at half-maximum (FWHM) of 27 nm. As far as we know, it is the best result in the dye-doped organic red emitting diode. We also made a device of G/ITO/NPB(25 nm)/DCM:Alq₃(29 nm)/DCM:PBD(26 nm)/Alq₃(20 nm)/LiF(1.2 nm)/Al(84 nm), in order to compare the performance of Alq₃ with that of 2-(4-biphenylyl)-5-(4-t-butylphenyl)-1,3,4-oxadiazole (PBD) as host material. It was found that the performance of device A is better than that of C both in brightness and color purity,as well as in EL efficiency.     

Gamma ray interactions with MoO3-doped lead phosphate glasses

The UV–Visible, Fourier transform infrared (FTIR) and Raman and electron spin resonance (ESR) spectra of undoped lead phosphate and MoO₃-doped glassy samples have been investigated. The UV–VIS absorption spectra were re-measured after successive gamma irradiation. Before irradiation, undoped sample exhibited strong ultraviolet absorption, which was attributed to co-absorption due to trace iron impurities (mainly Fe³⁺ ions) and lead Pb²⁺ ions. With the introduction of MoO₃ in progressive amounts, extra visible bands were recorded at about 400–440, 540, 750 and 870?nm. These bands are most likely correlated with the presence of Mo³⁺, Mo⁴⁺ and Mo⁵⁺ ions in the host glass. In the undoped specimen, gamma irradiation produced UV absorption bands that increased slightly with irradiation but no visible bands were recorded. Samples containing high MoO₃ content showed some resistance to irradiation with no bands in the visible region being observed. FTIR absorption spectra of the undoped and MoO₃-doped samples revealed the formation of metaphosphate and pyrophosphate structural units. Highly MoO₃-doped samples exhibited additional bands due to molybdate groups. Raman and ESR spectra were in agreement with UV–VIS and IR data, indicating the presence of molybdenum ions in lead phosphate glass, as Mo³⁺, Mo⁴⁺ and Mo⁶⁺ with different ratios. However, such glassy systems favor the trivalent species.     

Isophorone derivative as red dopant for organic electroluminescent devices

The donor–acceptor functionalized molecule, bis(4-(2-(3,3-dicyanomethylene-5,5-dimethyl-1-cyclohexylidene)vinyl)phenyl)(1-naphthyl)amine (DPN-4CN), with symmetrical structure, was investigated for its application in optoelectronic devices. Red organic light-emitting diodes (OLEDs) were fabricated by doping DPN-4CN in tris(8-hydroxyquinolino) aluminum (Alq₃) as red emitters, with a structure of ITO/NPB/Alq₃:DPN-4CN/BCP/Alq₃/LiF/Al. The device with a doping concentration of 2.5 wt% showed pure red emission with λ_max at 654 nm and CIE coordinates of (0.62, 0.36), a high brightness of 5080 cd m⁻² at a driving voltage of 12 V, a current efficiency of 2.14 cd A⁻¹ and an external quantum efficiency of 1.07% at a current density of 20 mA cm⁻². The current efficiencies and CIE coordinates of the device were almost constant over a current density from 1 to 200 mA cm⁻².     

Organic Light-Emitting Diodes with Magnesium Doped CuPc as an Efficient Electron Injection Layer

Bright organic electroluminescent devices are developed using a metal-doped organic layer intervening between the cathode and the emitting layer. The typical device structure is a glass substrate/indium-tin oxide （ITO）/copper phthalocyanine （CuPc）/N,N＇-bis-（1-naphthl）-diphenyl-1,1＇-biphenyl-4,4＇-diamine （NPB）/Tris（8-quinolinolato） aluminum（Alq3）/Mg-doped CuPc/Ag. At a driving voltage of 11 V, the device with a layer of Mg-doped CuPc （1：2 in weight） shows a brightness of 4312cd/m^2 and a current efficiency of 2.52cd/A, while the reference device exhibits 514 cd/m^2 and 1.25 cd/A.