低密度聚乙烯的升温淋洗分级及链结构研究

采用升温淋洗分级方法对密度相同、熔融指数不同、拉伸强度和断裂伸长率不同、膜的抗冲击强度和抗撕强度有明显差异的2种低密度聚乙烯样品进行了分级,并利用GPC、DSC、SSA、13C-NMR等多种手段对原样和级份进行了链结构表征.由13C-NMR得到样品A和B总的支化含量分别为3.93 mol%,4.82 mol%,都既含有短链支化又含有长链支化;TREF-GPC交叉分级结果可以看出,2个样品的主要分级级份集中在较高温度区域,A样品主要集中于80℃的淋洗温度,分子量集中于3.2×105区域,而B样品主要集中于75℃的淋洗温度,分子量集中于1.8×105区域,样品A具有稍高的分子量且高分子量部分含量较多.由DSC结果得知,样品A的结晶度为34.7%,级份A1~A9的结晶度在26.0%~37.4%;样品B结晶度为34.4%,其级份B1~B9的结晶度在26.2%~34.8%.另外通过热分级结果得出,不管是原样还是各个级份,都具有约10个左右的多重熔融峰,显示出分子链内具有非均匀性,2个样品级份的数均亚甲基序列长度均随着淋洗温度升高而增加,分别为34~86和32~84.此外,讨论了它们的链结构特点以及与性能之间的关系.     

短链支化聚乙烯的合成与表征

合成了两类结构明确的乙烯共聚物, 通过FTIR, GPC, ¹H NMR和¹³C NMR表征了产物的分子结构, 分别研究了分子量和短链支化含量对两类共聚物结晶性能的影响. 采用阴离子聚合制备分子量(M_w)20000~110000、分子量分布为1.1的1,2-结构摩尔分数为7%左右的聚丁二烯. 加氢反应后得到乙烯/1-丁烯模型共聚物的熔点和结晶度随着分子量的增加而下降. 采用茂金属催化剂Et[Ind]₂ZrCl₂催化乙烯与1-己烯共聚合, 制备分子量为100000左右, 共聚单体摩尔分数为0~5.5%的乙烯/1-己烯共聚物, DSC结果表明其熔点和结晶度随着共聚物中1-己烯含量的升高而降低.     

高密度聚乙烯的熔融支化及其对性能的影响

在引发剂过氧化二异丙苯、二官能度单体新戊二醇二丙烯酸酯和自由基活性调控剂二甲基二硫代氨基甲酸锌的存在下,使高密度聚乙烯进行熔融支化反应.研究表明,转矩曲线上的反应峰顶对应最佳反应时间,由此获得了凝胶量低的长链支化高密度聚乙烯.熔融支化反应使聚乙烯的分子量分布变宽,其支化程度随单体含量的增加而增大,呈现出更加明显的剪切变稀行为;长链支化结构的引入使改性聚乙烯的结晶度降低,长支链的成核作用使起始结晶温度增加,球晶尺寸明显减小.改性聚乙烯的支化程度和大分子拓扑结构的变化对耐环境应力开裂性能的影响显著,当单体含量超过0.6 phr时,长链支化分子形态从类似不对称星形转变为梳形,使得高密度聚乙烯的耐环境应力开裂时间产生突变,达1000 h以上,同时强度、模量和冲击韧性均得到明显提高.     

高密度聚乙烯的熔融支化及其对性能的影响木

在引发剂过氧化二异丙苯、二官能度单体新戊二醇二丙烯酸酯和自由基活性调控剂二甲基二硫代氨基甲酸锌的存在下,使高密度聚乙烯进行熔融支化反应.研究表明,转矩曲线上的反应峰顶对应最佳反应时间,由此获得了凝胶量低的长链支化高密度聚乙烯.熔融支化反应使聚乙烯的分子量分布变宽,其支化程度随单体含量的增加而增大,呈现出更加明显的剪切变稀行为;长链支化结构的引入使改性聚乙烯的结晶度降低,长支链的成核作用使起始结晶温度增加,球晶尺寸明显减小.改性聚乙烯的支化程度和大分子拓扑结构的变化对耐环境应力开裂性能的影响显著,当单体含量超过0.6 phr时,长链支化分子形态从类似不对称星形转变为梳形,使得高密度聚乙烯的耐环境应力开裂时间产生突变,达1000 h以上,同时强度、模量和冲击韧性均得到明显提高.     

茂金属聚乙烯分子链流变学模型研究进展

茂金属聚乙烯的分子链长支化结构对其流变特性有重要影响，长支链可以使熔体弹性和剪切变稀效应明显增强。本文介绍了茂金属聚乙烯分子链模型建立的理论依据，从流变学角度综述了近年来茂金属聚乙烯分子链结构模型的研究进展，阐述了有关的长链支化结构模型及其与流变性能的关系。     

利用非对称结构接枝单体调控聚丙烯熔融自由基支化反应

研究了具有不同双键官能团反应活性的非等活性接枝单体对于聚丙烯(PP)熔融自由基反应的影响,探索了有效调控反应选择性的途径.首先合成了2种具有不同双键活性的非对称支化单体丙烯酸烯丁酯(BAC)、1-(烯丁氧甲基)-4-乙烯基苯(BMVB),采用上述2种含有"非等活性双键"的多官能团化合物作为接枝单体制备长链支化聚丙烯(LCB-PP),探索降低LCB-PP制备过程中降解和交联副反应的途径,促进长链支化结构的形成.采用核磁、高温GPC(HT-GPC)及流变表征分析了改性样品的反应过程与支化结构.研究发现,将上述2种非对称接枝单体应用于过氧化物引发熔融接枝反应体系时,单体中高活性的双键能够把PP大分子自由基快速转变为较稳定的自由基,抑制PP的降解;而低活性的双键与PP大分子自由基反应产生支化结构,抑制交联反应.由于BMVB单体中高活性双键与低活性双键的竞聚率比值(17000)比BAC(2800)高,其对于自由基熔融反应过程具有更好的调控效果,表现出PP降解不明显且长支链在分子链间分布均匀.     

单茂钛/甲基铝氧烷催化剂乙烯/丙烯共聚合研究

改性甲基铝氧烷(mMAO)激活五甲基茂基三氯化钛(Cp TiCl3)催化乙烯 丙烯共聚合,控制两种单体的进料配比,得到单元序列分布不同的共聚物.混合单体中含有少量丙烯,共聚合活性高于相同聚合条件下乙烯均聚合的活性.用1 3C -NMR测定共聚物分子链的微观结构和单元序列分布,计算出单体的竞聚率;结果表明共聚物分子链中两种单体的序列分布均匀.混合单体中丙烯含量较大时,共聚物为完全无规共聚物;而当丙烯含量少时,丙烯链节或短的聚丙烯链段均匀分布于聚乙烯链段之间.共聚物经DSC分析,也证明不存在长序列的聚乙烯链段;因此,即便在进料气体中丙烯含量很少的情况下,共聚物仍然没有明显的熔融温度和结晶性.     

新型甾体类吡唑并[1,5-a]嘧啶化合物的合成

以雄烯二酮为原料,制得16E-苯亚甲基甾体衍生物（1）; 1和3-氨基吡唑反应合成了D-环吡唑并[1,5-a]嘧啶基修饰的雄烯二酮类衍生物,收率达72%,其结构经¹H NMR, ¹³C NMR和HR-MS(ESI)表征。     

新型茂钛催化剂合成聚乙烯-b-间规聚苯乙烯嵌段共聚物的研究Ⅱ.嵌段共聚物的分离及结构性能

将五甲基茂基三苄氧基钛 (Cp Ti(OBz) 3) 改性甲基铝氧烷 (mMAO)催化体系以顺序加料溶液法合成的乙烯与苯乙烯嵌段共聚反应产物进行沸丁酮、沸四氢呋喃 (THF)和沸氯仿等溶剂连续抽提分离 ,发现嵌段共聚物主要存在于THF和CHCl3的可溶级分中 ,嵌段共聚物的总含量占共聚产物的 2 2 8wt%～ 38 2wt% ,对THF和CHCl3可溶级分分别用 1 3C NMR、WAXD、DSC和GPC等手段进行表征 .1 3C NMR谱显示出含有支化聚乙烯链段和间规聚苯乙烯链段的嵌段共聚物特殊结构 ,WAXD谱表明嵌段共聚物因两链段的相互缠结使各自结晶度显著较低 ,由于嵌段共聚物苯乙烯链段较长、乙烯链段较短 ,DSC图谱只显示苯乙烯链段的结晶熔融峰 ,GPC曲线表明 ,单茂钛催化体系催化乙烯 苯乙烯嵌段共聚合的单一活性中心特征 .由此对Cp Ti(OBz) 3 mMAO催化体系的苯乙烯 乙烯嵌段共聚合机理进行初探     

高性能长链支化聚乙烯制备的研究进展

长链支化聚乙烯（LCB-PE）在聚乙烯链上含有长链的支化结构,因此具有优异的流变性能,从而改善了聚合物的加工性能,这是其它结构聚乙烯所不能比拟的。长链支化聚乙烯的制备方法有辐照法、茂金属共聚法和聚丁二烯加氢法等,本文综述了各种方法的基本原理和优缺点。辐照法制备LCB-PE的优点是比较简便,容易实现工业化生产,但也有制备的LCB-PE结构不明确,高能辐照对设备要求较高的缺点。茂金属共聚法制备的LCB-PE结构较明确,制备过程较易控制,但由于茂金属催化剂的专利问题而不易推广。聚丁二烯加氢法制备的LCB-PE其主链长度、支链长度和支链密度都可控,但过程较复杂,成本高,不易推广。     

Detection of long-chain branches in polyethylene via rheological measurements

The detection of long-chain branches(LCB) in polyethylene is of considerable importance as the processing properties of polyethylene are strongly affected by even a small amount of LCB. While the conventional characterization techniques such as GPC-MALS and13 C NMR fail or take very long time to detect low content of LCB, we turn to the rheological method, which is more sensitive to LCB. In our study, we performed oscillatory shear test, creep test and stress relaxation test on two series of metallocene linear low density polyethylene(LLDPE), revealing that the resins with LCB show higher zero-shear-rate viscosity, retarded relaxation and higher flow activation energy than those without or with less LCB. The resins with LCB showed shear thinning at very low shear rate and their zero-shear-rate viscosities were obtained via creep test. The content of LCB was quantitatively estimated from the flow activation energy. In addition, the modulus-time curves during stress relaxation of melt of the different resins obeyed the power law. The exponent of the resins with more LCB was 0.7, different from that of the resins with less LCB, around 1.7.     

An investigation of solute-liquid crystal interaction in hydrogen bonded complexes of palmitic acid and p-octyloxybenzoic acid

The orientational order of a liquid crystalline phase which has a specific solute-liquid crystal interaction was investigated using nuclear magnetic resonance. Three isotopically substituted species of palmitic acid (palmitic acid-d₃₁, 1-¹³C-2.2-H₂-palmitic acid-d₂₉ and 2,2,3,3-H₄-palmitic acid-d₂₇) were dissolved in the liquid crystal p-octyloxybenzoic acid (p-OOBA) and the proton, deuteron and carbon 13 NMR spectra recorded as a function of temperature. ¹H-¹³H dipolar couplings were observed using a spin echo pulse sequence which removes heteronuclear dipolar couplings to the chain deuterons. In the case of the carbon 13 labelled compound, ¹H-¹³C dipolar couplings could be observed by applying an additional refocusing pulse to the ¹³C spins. The dipolar and quadrupolar couplings were used to calculate the complete orientational order matrix of the alpha methylene segment of palmitic acid in p-OOBA. The liquid crystal was shown to largely determine the orientational order of the head group and this was attributed to intermolecular hydrogen bonding. The dipolar and quadrupolar couplings for the rest of the chain were interpreted in terms of a mean field equilibrium statistical model, based on the Samulski Inertial Frame Model. Hydrogen bonding was shown to be of greater importance in the orientational ordering of the solutes in the liquid crystal than are electrostatic interactions in the ordering of the amphiphile in the potassium palmitate/water system.     

酞侧基聚芳醚酮的核磁共振研究(Ⅰ)──链结构及NMR谱的归属

用1D NMR方法研究酞侧基聚芳醚酮(PEK-C)链结构,用二维同核化学位移相关与二维异核化学位移相关实验方法对1D NMR谱峰进行归属,探讨了二维异核远程相关实验在缩聚高分子研究中的应用,为PEK-C修饰机理以及共混相容机理的研究提供重要信息。溶液NMR谱图数据表明,PEK-C具有较规整的链结构。     

Synthesis and thermal properties of novel calix[4]arene derivatives containing 1,2,3-triazole moiety via K2CO3-catalyzed 1,3-dipolar cycloaddition reaction

Two calix[4]arene derivatives containing 1,2,3-triazole moiety were synthesized via K2CO3-catalyzed1,3-dipolar cycloaddition reaction between calix[4]arene-based azide and active methylene compounds in good yields.The structures of the two compounds synthesized herein were fully confirmed by 1HNMR,,（13）C NMR,and MS（ESI）.The thermal analysis showed that the mass losses of the synthesized compounds 4 and 5 containing 1,2,3-triazole groups are similar to each other.     

Multinuclear NMR studies of lead(II) soaps II. 13C and 1H studies of solid and liquid-crystalline phases

The solid and liquid-crystalline phases of two long chain lead(II) carboxylates have been studied by ¹³C and ¹H NMR spectroscopy. High resolution ¹³C NMR spectra of the solid phase of lead(II) decanoate and octadecanoate, reveal splittings of the peaks attributed to the carboxylate and adjacent methylene groups. This may result from two different environments for the carboxylate chains coordinated to the same Pb(II) ion. On going from the solid to liquid-crystalline or liquid phases, this splitting is lost, and small changes in chemical shift of the bands due to the methyl and methylene groups are observed. These are attributed to the onset of conformational disordering, and analysis of the data gives a gauche population in good agreement with that from Raman spectra and theoretical calculations. Longitudinal ¹³C relaxation times are reported. From these, and from spectral data, the -CH₃ group is seen to have different dynamics from the rest of the chain, and to retain high mobility even in the solid phase. Further information on the structural changes comes from proton NMR spectroscopy. The transverse ¹H relaxation of lead(II) decanoate shows two components, which are suggested to arise from a crystalline, and a relatively amorphous region of the compound. Study of the evolution of these as a function of temperature shows that the amorphous fraction is relatively low up to 335 K. but then increase rapidly, until at 365 K, close to the transition to the L, phase, it is 99 per cent- In parallel to these observations, changes in band shape were also observed and suggest a progressive fusion of the chains up to the temperature of this transition. The global ¹H spin-lattice relaxation was also studied as a function of temperature. and two components were observed between room temperature and approximately the tint phase transition. These are associated with populations of hydrogen nuclei with different mobilities.     

Synthesis and Biological Evaluation of Novel Saccharin Derivatives Containing 1,2,3-Triazole Moiety

A series of novel saccharin derivatives containing 1,2,3-triazole moiety was synthesized in satisfactory yields. The structures of all the compounds were elucidated and confirmed by Fourier transform infrared(FTIR) spectroscopy, ¹H and ¹³C nuclear magnetic resonance(¹H NMR, ¹³C NMR) spectroscopy, and high resolution mass spectrometry(HRMS). The bioassays indicated that most of the title compounds displayed some extent herbicidal activities at 100 μg/mL.     

Synthesis and structural characterisation of a novel tris-methylene bridged compound (NO) 4Fe2 Se(μ-CH2)3

The tris-methylene bridged compound (NO)₄Fe₂Se(μ-CH₂)₃ has been isolated. It has been characterised by IR and ¹H, ¹³C, and ⁷⁷Se NMR spectroscopy. Its structure has been determined by single-crystal X-ray diffraction methods. The structure consists of a heavy atom triangle consisting of one Se and two Fe atoms. The Fe-Fe and the two Fe-Se edges are bridged by methylene groups.     

C and H nuclear magnetic shielding and spin–spin coupling constants of C-enriched bromomethane in the gas phase

¹³C and ¹H NMR spectral parameters are investigated for ¹³CH₃Br in gaseous matrices. It is found that both the ¹³C and ¹H chemical shifts of ¹³CH₃Br are linearly dependent on solvent density. Similar dependence is also detected for one-bond spin–spin coupling, ¹J(CH). For the first time the ¹³C and ¹H magnetic shielding constants and ¹J(CH) spin–spin coupling are obtained for an isolated ¹³CH₃Br molecule together with the coefficients responsible for solute–solvent molecular interactions in gaseous matrices. The present experimental results confirm the accuracy of some recent ab initio calculations of nuclear magnetic shielding performed for bromomethane.     

基于固体核磁共振方法的蛋白质组装体三维结构解析

蛋白质组装体广泛存在于生物体内,具有相关生物学功能或与人类的重要疾病密切相关。蛋白质组装体分子量大,通常难以溶解和结晶,限制了常用的结构研究手段如X射线晶体学和液体NMR等在其高分辨三维结构解析中的应用。固体核磁共振技术(ssNMR)在难溶、非结晶样品的三维结构解析中具有独特的优势,尤其随着固体NMR硬件包括高场磁体和高性能的探头、固体NMR多维脉冲实验技术和样品制备技术特别是同位素标记技术的快速发展,固体NMR已经成为了蛋白组装体三维结构解析的重要手段。在样品制备方法方面,强调了样品制备条件的优化对得到构象均一样品的重要性,以及丰富的同位素标记方法的使用对固体NMR谱图分辨率提高的重要作用。同时多种脉冲序列如质子驱动自旋扩散技术(PDSD),偶极辅助旋转共振技术(DARR),质子辅助重偶技术(PAR)或转移回波双共振技术(TEDOR)等的建立和发展为结构约束条件收集提供了基本的技术方法。此外,固体NMR与其它实验技术如扫描透射电镜(STEM),冷冻电镜(Cryo-EM)等和理论模拟方法的联用能显著地提高固体NMR的能力,从而能解析分子量更大、结构更复杂的蛋白质组装体的三维结构。本文以Aβ纤维和T3SS针状体的三维结构解析为例介绍固体NMR在蛋白质组装体结构研究的最新实验方法,重点介绍最新的距离约束条件获取的实验方法进展,以及固体NMR与其它实验和理论模拟研究手段的联用在蛋白质组装体结构解析上的最新进展,期望有助于读者对固体NMR技术在蛋白质组装体的三维结构解析方面的研究进展有所了解。     

INVESTIGATION OF CHEMICAL CONSTITUENT FROM CELASTRUS ANGULATUS

Three new β-dihydroagarofuran sesquiterpene polyol esters,one alkaloid andtwo non-alkaloids,were isolated from the MeOH extract of seed oil of Celastrus angulatus.Their structures were elucidated on the basis of UV,IR,mass,NOE difference,~1H-NMR,~(13)C-NMR and ~1H-~(13)C long-range correlation spectroscopy.