高压下NbN结构和电子性质的第一性原理计算

摘要：利用密度泛函理论平面波赝势方法研究了NbN五种结构,即NaCl结构(Fm-3m); CsCl结构 (Pm-3m); ZB结构(F4-3m); 六角δ结构(P63/mmc) and ε (P-6m2)结构。本文对NbN五种结构的机械稳定性,弹性性质和高压下的电子结构等都进行了详细的研究。在NbN的五种晶体结构中,我们发现六角结构NbN要比立方结构稳定,这与实验结果相一致。我们还计算了NbN各种结构的晶格常数、体模量,弹性模量以及弹性各向异性等,结果与已有的理论和实验相吻合。同时发现在290GPa左右,NaCl结构转化为CsCl结构。为了更加深入的研究NbN的高压性能,我们研究了NbN的电子性质,结果发现NbN的不同结构具有金属性,并且在高压下原子间的杂化增强。     

高压下NbN结构和电子性质的第一性原理计算

利用密度泛函理论平面波赝势方法研究了NbN五种结构,即NaCl结构(Fm-3m); CsCl结构 (Pm-3m); ZB结构(F4-3m); 六角δ结构(P63/mmc) and ε (P-6m2)结构。本文对NbN五种结构的机械稳定性,弹性性质和高压下的电子结构等都进行了详细的研究。在NbN的五种晶体结构中,我们发现六角结构NbN要比立方结构稳定,这与实验结果相一致。我们还计算了NbN各种结构的晶格常数、体模量,弹性模量以及弹性各向异性等,结果与已有的理论和实验相吻合。同时发现在290GPa左右,NaCl结构转化为CsCl结构。为了更加深入的研究NbN的高压性能,我们研究了NbN的电子性质,结果发现NbN的不同结构具有金属性,并且在高压下原子间的杂化增强。     

高压下RhB的相变、弹性性质、电子结构及硬度的第一性原理计算

采用密度泛函理论中的赝势平面波方法系统地研究了高压下RhB的结构相变、弹性性质、电子结构和硬度.分析表明,RhB在25.3 GPa时从anti-NiAs结构相变到FeB结构,这两种结构的弹性常数、体弹模量、剪切模量、杨氏模量和弹性各向异性因子的外压力效应明显.电子态密度的计算结果显示,这两种结构是金属性的,且费米能级附近的峰随着压强的增大向两侧移动,赝能隙变宽,轨道杂化增强,共价性增强,非局域化更加明显.此外,硬度计算结果显示,anti-NiAs-RhB的金属性比较弱,有着较高的硬度,属于硬质材料.     

ZnTe结构相变、电子结构和光学性质的研究

运用密度泛函理论体系下的投影缀加波方法, 对闪锌矿和朱砂相结构的ZnTe在高压下的状态方程和结构相变进行了研究, 并分析了相变前后的原胞体积、电子结构和光学性质. 结果表明: 闪锌矿结构转变为朱砂相结构的相变压力为8.6 GPa, 并没有出现类似材料高压导致的金属化现象, 而是表现出间接带隙半导体特性. 相变后, 朱砂相结构Zn和Te原子态密度分布均向低能级方向移动, 带隙变小; 轨道杂化增强, 更有利于Te 5p与Zn 3d间的电子跃迁, 介电常数虚部主峰明显增强, 但宏观介电常数不受压力的影响.     

Ab-initio study of structural and electronic properties of AlAs

The structural properties, i.e. equilibrium lattice constant, transition pressure, bulk modulus and its pressure derivatives, together with electronic properties, i.e. energy bands, Compton profile and autocorrelation function, of AlAs are presented in this work. The linear combination of atomic orbitals (LCAO) method of the CRYSTAL code was applied considering the Perdew–Burke–Ernzerhof correlation energy functional and Becke's ansatz for the exchange. The total energy of AlAs as a function of primitive cell volume has also been calculated for the zincblende (B3), nickel arsenide (B8), sodium chloride (B1) and cesium chloride (B2) phases. Structural parameters of the B3, B8, B1 and B2 phases are determined. The calculated structural parameters are found to be in good agreement with the results of previous investigations. The spherically averaged theoretical values of Compton profile are in good agreement with an earlier measurement. The LCAO calculation shows an indirect band gap of 1.85?eV, in reasonable agreement with earlier data. On the basis of the equal-valence-electron-density Compton profile, it is found that AlAs is more ionic compared to AlSb.     

Theoretical calculations of structural,electronic, and elastic properties of CdSe_(1-x)Te_x:A first principles study

The plane wave pseudo-potential method was used to investigate the structural, electronic, and elastic properties of Cd Se_(1-x)Te_x in the zinc blende phase. It is observed that the electronic properties are improved considerably by using LDA + U as compared to the LDA approach. The calculated lattice constants and bulk moduli are also comparable to the experimental results. The cohesive energies for pure Cd Se and Cd Te binary and their mixed alloys are calculated. The second-order elastic constants are also calculated by the Lagrangian theory of elasticity. The elastic properties show that the studied material has a ductile nature.     

第一性原理研究硫化镉高压相变及其电子结构与弹性性质

采用第一性原理研究了CdS的六方纤锌矿(WZ), 立方闪锌矿(ZB) 和岩盐矿(RS)相在高压条件下的相稳定性、 相变点、电子结构以及弹性性能.WZ相与RS 相可以在相应的压强范围内稳定存在, 而ZB相不能稳定存在.压强大于2.18 GPa时, WZ相向RS相发生金属化相变.WZ相中S原子电负性大于Cd, 且电负性差值小于1.7, CdS的WZ相为共价晶体.高压作用下, S原子半径被强烈压缩, 有效核电荷增加, 对层外电子吸引能力提高, 电负性急剧增大, 导致S与Cd的电负性差值大于1.7, CdS的RS相以离子晶体存在. WZ相的C₄₄随压强增加呈下降趋势, 导致WZ相力学不稳定, 并向RS相转变.当压强大于2.18 GPa时, RS相C₁₁, C₁₂随压强增加而增大, 并且C₄₄保持稳定, 说明RS相具有良好的高压稳定性与力学性能. 关键词： 第一性原理 相变 电子结构 弹性性质     

First principles study of the structural,electronic, mechanical and superconducting properties of WX (X=C,N)

The structural, electronic, mechanical and superconducting properties of tungsten carbide (WC) and tungsten nitride (WN) are investigated using first principles calculations based on density functional theory (DFT). The computed ground state properties, such as equilibrium lattice constant and cell volume, are in good agreement with the available experimental data. A pressure induced structural phase transition is observed in both tungsten carbide and nitride, from a tungsten carbide phase (WC) to a zinc blende phase (ZB), and from a zinc blende phase (ZB) to a wurtzite phase (WZ). The electronic structure reveals that these materials are metallic at ambient conditions. The calculated elastic constants obey the Born-Huang criteria, suggesting that they are mechanically stable at normal and high pressure. Also, the superconducting transition temperature is estimated for the WC and WN in stable structures at atmospheric pressure.     

Elastic,mechanical, electronic properties and hardness of Nb2AsC from first principles

The study aims at the elastic, mechanical, electronic properties and hardness of Nb₂AsC using first principles based on the density functional theory method within the generalised gradient approximation. The calculated lattice parameters of Nb₂AsC are in good agreement with the experimental data. The five independent elastic constants are firstly calculated as a function of pressure, and our results indicate that it is mechanically stable in the applied pressure. The elastic anisotropy is examined through the computation of the direction dependence of Young's modulus. The pressure dependences of the bulk modulus, shear modulus, average velocity of acoustic waves and Debye temperature of Nb₂AsC are systematically investigated. The band structure and density of states are discussed, and the results show that the strong hybridisations C p–Nb d and As p–Nb d would be beneficial to the structure stability of Nb₂AsC. Based on the Mulliken population analysis, the hardness of Nb₂AsC is predicted.     

First principles study of structural stability,electronic structure and mechanical properties of ReN and TcN

The crystal structure, structural stability, electronic and mechanical properties of ReN and TcN are investigated using first principles calculations. We have considered five different crystal structures: NaCl, zinc blende (ZB), NiAs, tungsten carbide (WC) and wurtzite (WZ). Among these ZB phase is found to be the lowest energy phase for ReN and TcN at normal pressure. Pressure induced structural phase transitions from ZB to WZ phase at 214 GPa in ReN and ZB to NiAs phase at 171 GPa in TcN are predicted. The electronic structure reveals that both ReN and TcN are metallic in nature. The computed elastic constants indicate that both the nitrides are mechanically stable. As ReN in NiAs phase has high bulk and shear moduli and low Poisson's ratio, it is found to be a potential ultra incompressible super hard material.     

第一性原理研究Mg2 Si同质异相体的结构、电子结构和弹性性质

在第一性原理框架下,采用赝势平面波方法研究了三种Mg₂Si同质异相体的晶胞结构、电子结构和弹性性质随压强的变化关系.研究发现,反萤石结构Mg₂Si、反氯铅矿结构Mg₂Si和Ni₂In型Mg₂Si分别在压强为0-7 GPa,7.5-20.2 GPa和21.9-40 GPa范围内能够保持结构稳定.计算获得了不同压强下Mg₂Si的弹性常数、体模量、剪切模量、杨氏模量、泊松比和各向异 关键词： 态密度 电子结构 弹性常数 第一性原理     

ZrRh晶体结构、弹性性质和电子结构的第一性原理研究

运用基于密度泛函理论的第一性原理计算方法研究了ZrRh的晶体结构、弹性性质和电子结构性质.结果表明:计算的B2、B19'和ZrIr结构的平衡晶格常数与相应的实验参数符合很好.从形成焓和态密度的角度来看,ZrRh的相稳定顺序是ZrIrFe BB19'B2,ZrIr结构是最稳定的.ZrIr结构的形成焓最小,说明ZrIr结构最容易生成.利用应力-应变的方法计算了ZrRh的弹性常数,表明B2、FeB和ZrIr结构是力学稳定的.B/G和泊松比均表明ZrRh具有很好的延展性.对ZrRh的态密度研究发现,增强的Rh4d态与Zr4d态杂化作用是ZrIr结构稳定的主要原因.     

Superconducting properties of barium in three phases under high pressure from first principles

Electron-phonon coupling (EPC) in the three high-pressure phases of Ba is investigated using a pseudopotential plane-wave method based on density functional perturbation theory. The calculated values of superconducting critical temperature T c of Ba-I and Ba-II under pressure are consistent well with the trends observed experimentally. Moreover, Ba-V is found to be superconducting with a maximum T c exceeding 7.8 K at 45 GPa. With the increase of pressure, the values of T c increase in Ba I and Ba-II but the value of T c decreases in Ba-V. For Ba-I at pressures below 2 GPa, the increases of logarithmic average frequency ω log and electron-phonon coupling parameters λ both contribute to the enhancement of T c . For all the three phases at pressures above 2 GPa, T c is found to be primarily determined by λ . Further investigation reveals that for all the three phases, the change in λ with pressure can be explained mainly by change in the phonon frequency. Thus for Ba-II and Ba-V, although they exhibit completely different superconducting behaviors, their superconductivities have the same origin; the pressure dependence of T c is determined finally by the pressure dependence of phonon frequency.     

Theoretical study on the structural,mechanical, electronic properties and QTAIM of CrB_4 as a hard material

Using the first-principles calculations based on spin density functional theory(DFT), we investigate the structure,elastic properties, and electronic structure of Pnnm-CrB4. It is found that Pnnm-CrB_4 is thermodynamically and mechanically stable. The calculated elastic properties such as the bulk modulus, shear modulus, Young's modulus, and Poisson's ratio indicate that CrB_4 is an incompressible material. Vicker's hardness of Pnnm-CrB_4 is estimated to be 26.3 GPa, which is in good agreement with the experimental values. The analysis of the investigated electronic properties shows that PnnmCrB_4 has the metallic character and there exist strong B–B and Cr–B bonds in the compound, which are further confirmed by Bader's quantum theory of atoms in molecules(QTAIM). Thermodynamic properties are also investigated.     

First-principles study of structural and elastic properties of CrO2 at high pressure

The structural and elastic properties of CrO₂ in the rutile phase under high pressures have been investigated using pseudopotential plane-wave method based on density functional theory. The optimized lattice parameters and the bulk modulus at zero pressure agree well with available experimental and theoretical data. The elastic constants C ₁₁, C ₁₂, C ₄₄, C ₃₃, C ₁₃, and C ₆₆ at zero pressure are calculated to be 359.91, 264.69, 143.28, 309.45, 218.45, and 260.74 GPa, respectively. Elastic constants, bulk modulus, shear modulus, Young's modulus, and Poisson's ratio under pressures are obtained. Our results indicate that the rutile phase is mechanically stable below 11.99 GPa. The elastic anisotropy of rutile phase under pressures has also been predicted.     

ZnO原子链的结构稳定性和电子性质的第一性原理研究

本文采用基于密度泛函理论的第一性原理平面波赝势法,研究了ZnO原子链的结构稳定性和电子性质.结果表明：ZnO分子可以形成直线形结构、梯子形结构以及双梯子形结构等一维链式结构,而之字形链状结构是不能稳定存在的.计算结果也表明：这些稳定存在的一维原子链结构均表现出间接带隙的特征,而之字形结构的原子链却表现出了类似金属的能带特征. 关键词： 原子链 结构稳定性 电子结构 第一性原理计算     

SrCoO3电子结构和磁学性质的第一性原理研究

通过基于密度泛函理论的广义梯度近似GGA+U方法对铁磁相SrCoO₃的电子结构和磁学性质进行了系统研究.结果表明:随着U值的增大,对于Co离子,主自旋方向的t_2g和e_g态向低能级移动,而次自旋方向的t_2g和e_g态向高能级移动;O2p电子态的分布基本不随U变化.能带结构表明,U大约在7-8eV之间时,SrCoO₃由金属性转变为半金属性.U值小于7eV时,Co离子的磁矩随着U值的增大几乎成线性增大,而当U大于7eV后基本保持不变.结合实验结果,本文认为U取8eV时得到的计算结果更为合理,Co离子的磁矩为3.19μв,且SrCoO₃表现出半金属特性.     

Elastic,dynamical, and electronic properties of LiHg and Li3Hg: First-principles study

The elastic, dynamical, and electronic properties of cubic LiHg and Li₃Hg were investigated based on first-principles methods. The elastic constants and phonon spectral calculations confirmed the mechanical and dynamical stability of the materials at ambient conditions. The obtained elastic moduli of LiHg are slightly larger than those of Li₃Hg. Both LiHg and Li₃Hg are ductile materials with strong shear anisotropy as metals with mixed ionic, covalent, and metallic interactions. The calculated Debye temperatures are 223.5 K and 230.6 K for LiHg and Li₃Hg, respectively. The calculated phonon frequency of the T_2g mode in Li₃Hg is 326.8 cm⁻¹. The p states from the Hg and Li atoms dominate the electronic structure near the Fermi level. These findings may inspire further experimental and theoretical study on the potential technical and engineering applications of similar alkali metal-based intermetallic compounds.     

Structural,elastic, thermodynamic and electronic properties of LuX (X = N,Bi and Sb) compounds: first principles calculations

ABSTRACT

The structural, electronic, elastic and thermodynamic properties of LuX (X = N, Bi and Sb) based on rare earth into phases, Rocksalt (B1) and CsCl (B2) have been investigated using full-potential linearized muffin-tin orbital method (FP-LMTO) within density functional theory. Local density approximation (LDA) for exchange-correlation potential and local spin density approximation (LSDA) are employed. The structural parameters as lattice parameters a₀, bulk modulus B, its pressure derivate B’ and cut-off energy (E_c) within LDA and LSDA are presented. The elastic constants were derived from the stress–strain relation at 0 K. The thermodynamic properties for LuX using the quasi-harmonic Debye model are studied. The temperature and pressure variation of volume, bulk modulus, thermal expansion coefficient, heat capacities, Debye temperature and Gibbs free energy at different pressures (0–50 GPa) and temperatures (0–1600 K) are predicted. The calculated results are in accordance with other data.     

High pressure structural,electronic and vibrational properties of InN and InP

A first-principles plane wave self-consistent method with the Ultrasoftpseudopotential scheme in the framework of density functional theory is performed to study the high pressure structural, electronic and vibrational properties of InX (X = N, P) for the zinc-blende (ZnS/B3), rock-salt (NaCl/B1) and cesium-chloride (CsCl/B2) phases. We also calculate the phase transition pressures among these different phases. Conclusions based on electronic energy band structure, phonon dispersion and phonon density of states at high pressure phases along phase transition regions are outlined.