Synthesis and structural properties of polypyrrole/nano-Y2O3 conducting composite

In this work, polypyrrole/nano-Y₂O₃ conducting composite was synthesized by chemical oxidative polymerization. The composite was characterized using transmission electron microscopy, X-ray diffraction, Fourier-transform infrared spectra, UV-vis absorption spectra, X-ray photoelectron spectroscopy and electrical conductivity measurements. The results indicate that Y₂O₃ nanoparticles are almost enwrapped by polypyrrole. The addition of Y₂O₃ nanoparticles results in changes in the surface structure and conductivity of the composite. Thermogravimetric analysis shows that composite has better thermal stability than that of pure polypyrrole.     

Effect of calcination temperature on the structure and hydroxylation activity of Ni0.5Cu0.5Fe2O4 nanoparticles

Nanocrystalline Ni_0.5Cu_0.5Fe₂O₄ was synthesized by sol-gel method with varying calcination temperature over the range of 500-1000. The powders obtained were characterized by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). In addition, thermal analysis (TG-DTG-DTA) of the precursor was carried out. The study reveals the simultaneous decomposition and ferritization process at rather low temperature (280-350). For the crystalline structure investigated, single cubic spinel is gained when the precursor was decomposed at 800-1000, whereas separated crystal CuO formed when calcination temperature is below 800. The increase of calcination temperature favors the appearance of Fe_B³⁺, Cu_A²⁺ and O on the spinel surface. The hydroxylation activity is relative to the amount of Cu_B²⁺ species on the spinel surface. The lattice oxygen species on the spinel surface are favorable for the deep oxidation of phenol.     

Influence of postdeposition annealing on structural properties and electrical characteristics of thin Tm2O3 and Tm2Ti2O7 dielectrics

We describe the structural properties and electrical characteristics of thin thulium oxide (Tm₂O₃) and thulium titanium oxide (Tm₂Ti₂O₇) as gate dielectrics deposited on silicon substrates through reactive sputtering. The structural and morphological features of these films were explored by X-ray diffraction, X-ray photoelectron spectroscopy, secondary ion mass spectrometry, and atomic force microscopy, measurements. It is found that the Tm₂Ti₂O₇ film annealed at 800 °C exhibited a thinner capacitance equivalent thickness of 19.8 Å, a lower interface trap density of 8.37 × 10¹¹ eV⁻¹ cm⁻², and a smaller hysteresis voltage of ∼4 mV than the other conditions. We attribute this behavior to the Ti incorporated into the Tm₂O₃ film improving the interfacial layer and the surface roughness. This film also shows negligible degrees of charge trapping at high electric field stress.     

Auger electron/X-ray photoelectron and cathodoluminescent spectroscopic studies of pulsed laser ablated SrAl2O4:Eu,Dy thin films

Auger electron/X-ray photoelectron and cathodoluminescent (CL) spectroscopic studies were conducted on pulsed laser deposited SrAl₂O₄:Eu²⁺,Dy³⁺ thin films and the correlation between the surface chemical reactions and the decrease in the CL intensity was determined. The Auger electron and the CL data were collected simultaneously in a vacuum chamber either maintained at base pressure or backfilled with oxygen gas. The data were collected when the films were irradiated for 14 h with 2 keV electrons. The CL emission peak attributed to the 4f⁶5d¹ → 4f⁷ transitions was observed at ∼521 nm and the CL intensity of the peaks degraded at different rates in different vacuum conditions. X-ray photoelectron spectroscopy (XPS) data collected from degraded films suggest that strontium oxide (SrO) and aliminium oxide (Al₂O₃) were formed on the surface of the film as a result of electron stimulated surface chemical reaction (ESSCR).     

Synthesis, structure and optical properties of Eu/TiO2 nanocrystals at room temperature

The nanocrystal samples of titanium dioxide doped with europium ion (Eu³⁺/TiO₂ nanocrystal) are synthesized by the sol-gel method with hydrothermal treatment. The Eu³⁺ contents (molar ratio) in the samples are 0, 0.5%, 1%, 2%, 3% and 4%. The X-ray diffraction, UV-Vis spectroscopy data and scanning electron microscope image show that crystallite size is reduced by the doping of Eu³⁺ into TiO₂. Comparing the Raman spectra of TiO₂ with Eu³⁺/TiO₂ (molar ratio Eu³⁺/TiO₂=1%, 2% and 4%) nanocrystals at different annealing temperatures indicates that the anatase-to-rutile phase transformation temperatures of Eu³⁺/TiO₂ nanocrystals are higher than that of TiO₂. This is due to the formation of Eu-O-Ti bonds on the surface of the TiO₂ crystallite, as characterized by the X-ray photoelectron spectroscopy. The photoluminescence spectra of TiO₂ in Eu³⁺/TiO₂ nanocrystals are interpreted by the surface self-trapped and defect-trapped exciton relaxation. The photoluminescence of Eu³⁺ in Eu³⁺/TiO₂ nanocrystals has the strongest emission intensity at 2% of Eu³⁺ concentration.     

PL and CL degradation and characteristics of SrAl2O4: Eu,Dy phosphors

Strontium aluminate phosphors are ideal for luminescent infrastructure materials. Their brightness and persistent glow time are much higher than previously used sulphide phosphors. Strontium aluminates prepared by the sol–gel and combustion methods are compared with commercially available strontium aluminate. High luminescent efficient SrAl₂O₄:Eu²⁺,Dy³⁺ pulsed laser deposited (PLD) thin films were also produced using the commercially available powder. Photoluminescence (PL) degradation studies showed that the phosphor intensity decreased about 20% over a period of 2 weeks under ultraviolet (UV) irradiation. Auger electron spectroscopy (AES) and X-ray photoelectron spectroscopy (XPS) showed that cathodoluminescence (CL) degradation is due to the formation of SrO due to electron stimulated surface reactions. The light output mechanism of the phosphor is also discussed in more detail.     

NaREO2 (RE= Lu，Y) 的制备及其结构的研究

用高温固相法制备了NaLuO2和NaYO2晶体粉体.制备纯相的NaLuO2粉体晶体困难,而制备纯相NaYO2粉体晶体相对容易.为了测定NaLuO2产物中含少量Lu2O3不纯相的量,用X射线衍射绝标法确定了样品中这两者的重量比和谱峰比的关系,得到了绝标法常数kLu2O3关键词： 2')" href="#">NaLuO2 2')" href="#">NaYO2 2O3')" href="#">Lu2O3 XRD定量分析 稀土发光     

退火对He注入及随后208Pb27+辐照的Al2O3单晶PL谱的影响

利用高能离子研究了110 keV 的He⁺注入Al₂O₃单晶及随后230 MeV的²⁰⁸Pb²⁷⁺辐照并在不同温度条件下退火样品的光致发光的特性. 从测试结果可以清楚地看到在375 nm，390 nm，413 nm 和450 nm 出现了强烈的发光峰. 经过600 K退火2 h后测试结果显示，390 nm发光峰增强剧烈，而别的发光峰显示不明显. 在900 K退火条件下，390 nm的发光峰开始减弱相反在510 nm出现了较强的发光峰，到1100 K退火完毕后390 nm的发光峰完全消失，而510 nm的发光峰相对增强. 从辐照样品的FTIR谱中看到，波数在460—510 cm^-1间的吸收是振动模式，经过离子辐照后，吸收带展宽，随着辐照量的增大，Al₂O₃振动吸收峰消失，说明Al₂O₃振动模式被完全破坏. 1000—1300 cm^-1之间为Al-O-Al桥氧的伸缩振动模式，辐照后吸收带向高波数方向移动. 退火后的FTIR谱变化不大.     

Superacid Catalyst SO42-/ZrO2-La2O3 Prepared by Ultrasonic Co-precipitation and Low Temperature Aging

低温陈化超声波共沉淀法制得SO₄^2-/ZrO^2-La₂O₃前驱体, 经H₂SO₄处理, 在不同温度下焙烧得到纳米晶催化剂SO₄^2-/ZrO^2-La₂O₃;用Hammett指示剂法测定其酸性. 用XRD、BET、TEM、IR和XPS对样品进行表征,其催化活性用醋酸和甘油的酯化反应进行了评价. 结果表明经超声波搅拌和低温(-15 ºC)陈化,650 ºC焙烧4 h得到的固体超强酸表现出较高催化活性.     

Effects of dopant concentrations on phosphorescence properties of Eu/Dy-doped Sr3MgSi2O8

Long afterglow Sr₃MgSi₂O₈: Eu, Dy phosphor with high brightness was prepared by sintering at high temperature and weak reductive atmosphere. The luminescent properties of this photoluminescent pigment were studied systematically by investigating concentration effects. The analytical results indicated that the main emission peaks appear at 482 nm. The excitation and emission spectra of this phosphor show that both of them are broadband. This is ascribed to the 4f⁷→4f⁶5d¹ transition of Eu²⁺ in the pigment matrix, which is in good agreement with the calculated value of 470 nm, and implies that luminescent centers Eu²⁺ occupy the deca-coordinated Sr²⁺ sites with the host of Sr₃MgSi₂O₈.     

Structural characteristics and morphology of SmxCe1−xO2−x/2 thin films

Effect of the deposition temperature (200 and 500 °C) and composition of Sm_xCe_1−xO_2−x/2 (x = 0, 10.9–15.9 mol%) thin films prepared by electron beam physical vapor deposition (EB-PVD) and Ar⁺ ion beam assisted deposition (IBAD) combined with EB-PVD on structural characteristics and morphology/microstructure was investigated. The X-ray photoelectron spectroscopy (XPS) of the surface and electron probe microanalysis (EPMA) of the bulk of the film revealed the dominant occurrence of Ce⁴⁺ oxidation state, suggesting the presence of CeO₂ phase, which was confirmed by X-ray diffraction (XRD). The Ce³⁺ oxidation states corresponding to Ce₂O₃ phase were in minority. The XRD and scanning electron microscopy (SEM) showed the polycrystalline columnar structure and a rooftop morphology of the surface. Effects of the preparation conditions (temperature, composition, IBAD) on the lattice parameter, grain size, perfection of the columnar growth and its impact on the surface morphology are analyzed and discussed.     

Annealing effects on the optical and structural properties of Al2O3/SiO2 films as UV antireflection coatings on 4H-SiC substrates

Al₂O₃/SiO₂ films have been prepared by electron-beam evaporation as ultraviolet (UV) antireflection coatings on 4H-SiC substrates and annealed at different temperatures. The films were characterized by reflection spectra, ellipsometer system, atomic force microscopy (AFM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS), respectively. As the annealing temperature increased, the minimum reflectance of the films moved to the shorter wavelength for the variation of refractive indices and the reduction of film thicknesses. The surface grains appeared to get larger in size and the root mean square (RMS) roughness of the annealed films increased with the annealing temperature but was less than that of the as-deposited. The Al₂O₃/SiO₂ films maintained amorphous in microstructure with the increase of the temperature. Meanwhile, the transition and diffusion in film component were found in XPS measurement. These results provided the important references for Al₂O₃/SiO₂ films annealed at reasonable temperatures and prepared as fine antireflection coatings on 4H-SiC-based UV optoelectronic devices.     

Synthesis of ZnFe2O4 nanomagnets by Fe-ion implantation into ZnO and post-annealing

Fe ions of dose 8 × 10¹⁶ cm^-2 are implanted into a ZnO single crystal at 180 keV. Annealing at 1073 K leads to the formation of zinc ferrite (ZnFe₂O₄), which is verified by synchrotron radiation X-ray diffraction (SR-XRD) and X-ray photoelectron spectroscopy (XPS). The crystallographically oriented ZnFe₂O₄ is formed inside the ZnO with the orientation relationship of ZnFe₂O₄ (111)//ZnO (0001). Superconducting quantum interference device (SQUID) measurements show that the as-implanted and post-annealing samples are both ferromagnetic at 5 K. The synthesized ZnFe₂O₄ is superparamagnetic, with a blocking temperature (T_B = 25 K), indicated by zero field cooling and field cooling (ZFC/FC) measurements.     

Theoretical investigation of optical spectra and covalent effect of Cr in Y2Ti2O7 and Y2Sn2O7

In this work, the complete matrix of optical spectral levels in trigonal symmetry of 3d² (3d⁸) ions are established on basis of strong field coupling mechanism by using two spin–orbit coupling parameters model. The contribution of the spin–orbit coupling of ligand to the optical spectra has been included in these formulas. As an application, the optical spectra of Cr⁴⁺ in Y₂Ti₂O₇ and Y₂Sn₂O₇ have been studied by the complete diagonalization (energy matrix) method. The covalent effect has been studied and the difficulty about Dq parameter in explanation of optical spectra of Cr-doped Y₂Ti₂O₇ and Y₂Sn₂O₇ is removed. The theoretical results are in good agreement with observed data.     

Far IR transmission spectra of an YBa2Cu3O7−δ thin film

Abstract

The FIR transmission of an YBa₂Cu₃O_7-δ film 1000 Å thick deposited on an MgO plate has been studied from 20 cm^?1 to 4000 cm^?1 at T = 300 K, and at 120 K, 80 K and 7 K. i) The spectra for the normal state are well fitted if a mid-IR oscillator of high strength and high damping is added to the simplest Drude model. ii) The spectra for the superconductive state do not show significant variations of transmission vs. temperature for ω > 120 cm^?1, which should be in agreement with a weak BCS coupling 2Δ = 3.5 kT_c . iii) The FIR transmission at 7 K for ω = 20 cm^?1 is not zero (around 1%) and seems to confirm that the low-temperature perovskite is made of two phases: a superconducting, and a normal one, the proportion of the first one increasing when the film temperature is decreased.     

Structural properties of Al2O3 dielectrics grown on TiN metal substrates by atomic layer deposition

We investigated on the structural properties of Al₂O₃ dielectrics grown on TiN metal substrates using an atomic layer deposition technique with tri-methyl-aluminum and either O₃ or H₂O as the precursor and oxidant, respectively. The structural and morphological features of these films were examined by atomic force microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy measurements. We find that Al₂O₃ dielectric films with the O₃ oxidant exhibit a rough morphology, a thick TiO₂ film, and a small amount of contaminants such as carbon and hydrogen. The reason for the rapid diffusion of oxygen atoms into the TiN lattice leads to the formation of TiO₂ layer on the TiN substrate. This is due to the higher oxidation potential of the O₃ compared to the H₂O.     

“In situ” XPS study of band structures at Cu2O/TiO2 heterojunctions interface

In an attempt to investigate influence of the defects on electronic structure of Cu₂O/TiO₂ heterojunctions, thin Cu₂O layers were successively deposited on TiO₂ that has different levels of defect concentrations, and the resultant band bending and offset characteristics were studied by in situ X-ray photoelectron spectroscopy (XPS). The TiO₂ substrates with defects were prepared by Ar⁺ sputtering, followed by annealing at different temperatures in oxygen atmosphere. Presence of the defects in TiO₂ surface dramatically influences on the band bending and band offset at the interface: more defects are on TiO₂ surface, less band bending are at the interface, inducing smaller conduction band offsets. On the reduced TiO₂ surface, Cu₂O was disproportionately decomposed to form CuO and Cu.     

结合除谱,差谱,二阶差谱的二氯化铜水溶液中直接接触离子对的紫外可见吸收光谱研究

The microstructure of aqueous CuCl₂ has been studied through lots of technologies for many years; however, it remains a controversial subject. In this study, a new spectroscopic method has been proposed to analyze the UV-visible spectra of thin film of CuCl₂/H₂O solutions at different concentrations. This method is the combination of ratio spectra, difference spectra and second order difference spectra. By using this method, two new bands at ~230 and ~380 nm are obviously observed. The bands are assigned as the contacted ion pairs[CuCl₃(H₂O)_n]^- or[CuCl₄(H₂O)_n]^2-, which demonstrates that ion pairs exist in the CuCl₂/H₂O solution. Such finding agrees with the recent theoretical spectra obtained by time-dependent density functional theory. Furthermore, the populations of the contacted ion pairs are discussed. This study not only offers the direct spectroscopic evidence of[CuCl₃(H₂O)_n]^- or[CuCl₄(H₂O)_n]^2- in aqueous CuCl₂, but also suggests that the spectroscopic analysis method is powerful to extract the weak bands in a strong overlapping spectrum.     

Electronic structure studies of the spinel CoFe2O4 by X-ray photoelectron spectroscopy

The spinel CoFe₂O₄ has been synthesized by combustion reaction technique. X-ray photoelectron spectroscopy shows that samples are near-stoichiometric, and that the specimen surface both in the powder and bulk sample is most typically represented by the formula (Co_0.4Fe_0.6)[Co_0.6Fe_1.4]O₄, where cations in parentheses occupy tetrahedral sites and those within square brackets in octahedral sites. The results demonstrate that most of the iron ions are trivalent, but some Fe²⁺ may be present in the powder sample. The Co 2p_3/2 peak in powder sample composed three peaks with relative intensity of 45%, 40% and 15%, attributes to Co²⁺ in octahedral sites, tetrahedral sites and Co³⁺ in octahedral sites. The O 1s spectrum of the bulk sample is composed of two peaks: the main lattice peak at 529.90 eV, and a component at 531.53 eV, which is believed to be intrinsic to the sample surface. However, the vanishing of the O 1s shoulder peak of the powder specimen shows significant signs of decomposition.