Effects of strontium on the characteristics of Pb(Zr1/2Ti1/2)O3--Pb(Zn1/3Nb2/3)O3 ceramics

The dielectric and piezoelectric properties of pyrochlore-free lead zirconate titanate-lead zinc niobate ceramics were investigated systematically as a function of Sr doping. The powders of Pb_{(1? x )}Sr _x [0.7(Zr_{1 / 2}Ti_{1 / 2})–0.3(Zn_{1 / 3}Nb_{2 / 3})]O₃, where x?=?0–0.06 were prepared using the columbite-(wolframite) precursor method. The ceramic materials were characterized using X-ray diffraction, dielectric spectra, hysteresis and electromechanical measurements. The phase-pure perovskite phase of Sr-doped PZN--PZT ceramics was obtained over a wide compositional range. The results showed that the optimized electrical properties were also achieved at composition x?=?0.0, which were K _P?=?0.69, d ₃₃?=?670?pC?N^?1, P _r?=?31.9?µC?cm^?2 and ε_rmax?=?18600. Maximum dielectric constant values of the systems decreased rapidly with increasing Sr concentration. Moreover, with increasing Sr concentration dielectric constant versus temperature curves become gradually broader. The diffuseness parameter increased significantly with Sr doping. Furthermore, Sr doping has been shown to produce a linear reduction in the transition temperature (T _m)?=?294.1–12.7x°C with concentration (x). Sr shifts the transition temperature of this system at a rate of 12.7°C?mol^?1%.     

等静压下0.75Pb（Mg1/3Nb2/3）O3-0.25PbTiO3陶瓷的介电性能研究

研究了等静压对0.75Pb（Mg_1/3Nb_2/3）O₃-0.25PbTiO₃（PMN-25PT）陶瓷介电温谱的影响,PMN-25PT剩余极化随等静压变化和等静压压致相变.结果表明,随着压力增加,PMN-25PT的介电峰值温度T_m降低,/+{dT_m}/-{dP}≈-4℃/kbar,极化弛豫增强;剩余极化随压力增加连续减小;介电常数对压力的依赖关系与对温度场的依赖相似,压力诱导PMN-25PT发生弛豫铁电—顺电相变,相变为宽化的渐变过程,频率色散和极化弛豫更加强烈和普遍. 关键词： 铌镁酸铅-钛酸铅 等静压 介电弛豫 压致相变     

Dielectric and impedance measurements on (1−x)Ba(Fe1/2Ta1/2)O3-xBa(Zn1/3Ta2/3)O3 ceramics

In this work, ((1−x)Ba(Fe_1/2Ta_1/2)O₃-xBa(Zn_1/3Ta_2/3)O₃), ((1−x)BFT-xBZT) ceramics with x = 0.00–0.12 were synthesized by the solid–state reaction method. X-ray diffraction data revealed that both the powders and ceramics were of a pure-phase cubic perovskite structure. All ceramics showed large dielectric constants. For the x = 0.12 sample, a very high dielectric constant (>20,600) was observed. A lowering in the dielectric loss compared to pure BFT ceramics was observed with the BZT addition. The impedance measurements indicated that BZT has a strong effect on the bulk grain and grain boundary resistance of BFT ceramics. These results are in agreement with the measured dielectric properties. Based on dielectric and impedance results, (1−x)BFT-xBZT ceramics could be of great interest for high performance dielectric materials applications due their giant dielectric constant behavior.     

Magnetoelectricity in the PbFe1/2Nb1/2O3 Ceramics

The magnetodielectric effect (the influence of a magnetic field H on the dielectric constant ?) and the magnetoelectric effect (the influence of an electric field E on the magnetoelectric constant ??) of the PbFe_1/2Nb_1/2O₃ ceramics have been investigated at temperatures T in the range from 50 to 200°C, including the Curie point T _C ? 98°C. It has been demonstrated that there is a correlation of these effects with the shift of the ferroelectric-paraelectric phase transition temperature in a magnetic field.     

Effect of BiFeO3 addition on Bi2O3–ZnO–Nb2O5 based ceramics

In this paper, low temperature sintering of the Bi₂(Zn_1/3Nb_2/3)₂O₇ (β-BZN) dielectric ceramics was studied with the use of BiFeO₃ as a sintering aid. The effects of BiFeO₃ contents and the sintering temperature on the phase structure, density and dielectric properties were investigated. The results showed that the sintering temperature could be decreased and the dielectric properties could be retained by the addition of BiFeO₃. The structure of BiFeO₃ doped β-BZN was still the monoclinic pyrochlore phase. The sintering temperature of BiFeO₃ doped β-BZN ceramics was reduced from 1000 °C to 920 °C. In the case of 0.15 wt.% BiFeO₃ addition, the β-BZN ceramics sintered at 920 °C exhibited good dielectric properties, which were listed as follows: ε_r = 79 and tan δ = 0.00086 at a frequency of 1 MHz. The obtained properties make this composition to be a good candidate for the LTCC application.     

Structural and electrical behavior of Pb(Mg1/4Cd1/4Mo1/2)O3 ceramics

Preliminary X-ray structural analysis of polycrystalline Pb(Mg_1/4Cd_1/4Mo_1/2)O₃ ceramics, prepared by a solid-state reaction technique, provides single-phase orthorhombic structure at room temperature. Detailed dielectric studies of the material as a function of temperature reveal a sharp phase transition at temperature T_c=49°C obeying Curie-Weiss behavior. Scanning electron microscope (SEM) studies of the sample show the uniform distribution of grains in the samples. A dielectric anomaly and ferroelectric phase transition observed at 49°C was supported by polarization studies. The activation energy of the sample was calculated from the dielectric data. The variation of dc resistivity with temperature suggests that the compound behaves as a negative temperature coefficient resistor (NTCR).     

Effect of phase transformation on optical and dielectric properties of zirconium oxide nanoparticles

Zirconium oxide nanoparticle (ZrO₂) is synthesized by the hydrothermal method at different calcination temperatures. The structural analysis is carried out by X-ray diffraction and Raman spectra. The sample prepared at 400 °C and 1100 °C showed the cubic and monoclinic phase, respectively, and the sample calcined at 600 °C and 800 °C showed the mixed phase with co-existence of cubic and monoclinic phases. Furthermore, the morphology and particle size of these samples were investigated by scanning electron microscope (SEM) and transmission electron microscope (TEM) analysis. The band gap estimated from UV–Vis spectra of ZrO₂ (zirconia) nanocrystalline materials calcined at different temperatures from 400 °C to 1100 °C was in the range of 2.6–4.2 eV. The frequency dependence of dielectric constant and dielectric loss was investigated at room temperature. The low frequency region of dielectric constant is attributed to space charge effects.     

Preface

Phenylethyl ammonium trichloromercurate exhibits a structural phase transition at 402K Phase I—(402K)→ Phase II

This transition has been characterized by differential scanning calorimetry, dielectric measurements and X-ray diffraction. The space groups and the cell parameters of both phases were determined by X-ray diffraction from single crystals and powder samples. Phase I has space group I2 or I2/m, a = 25.88(2) Å, b = 7.792(3) Å; c = 5.971(4) Å; β = 96.14(1)°. Phase II has orthorhombic symmetry, space group Cmm2 or C222 with a = 25.91(1) Å; b = 7.836(5) Å; c = 6.116(4) Å.     

Orthorhombic structure: a necessity in superconducting 1-2-3 compounds

X-ray and resistivity measurements on YBa₂Cu₃O_7−δ (1-2-3) samples show that for the same but low oxygen concentration,δ⋍0·55, no superconducting transition down to 4·2 K is observed for the tetragonal phase samples while the orthorhombic phase shows aT _c ∼ 31 K. The effect of oxygen concentration onT _c is isolated.T _c=91±1 K has, however, been observed continuously for the normal oxygen annealed samples,δ⋍0·07. The experimental results suggest strongly the necessity of the 1-2-3 compound to be in the orthorhombic phase for the superconducting mechanism to be operative.     

Kinetics of oxygen desorption in Y Ba2Cu3O7-δ

In this paper the kinetics of oxygen desorption from Y Ba₂Cu₃O_7-δ has been investigated and measurements carried out in the temperature range 350–750 C. It is shown that the oxygen desorption is diffusion-controlled (and not surface-controlled), and characteristic of diffusion from small grains in a loosely coupled porous matrix. At every temperature a number of time constants with well-defined ratios appear and have been identified and measured. These time constants can be related to the average bulk diffusion constant which shows an Arrhenius behaviour with deviations around 750°C which are ascribed to the well-known orthorhombic to tetragonal transition. In this paper we establish the basic underlying physical mechanism of oxygen desorption in Y Ba₂Cu₃O_7-δ.     

Perovskite Pb(Sc1/2Nb1/2)O3 nanopowders synthesized by surfactant-modulated precipitation

A novel surfactant-modulated precipitation method is proposed to produce pure perovskite Pb(Sc_1/2Nb_1/2)O₃ (PSN) nanopowders at a low temperature of 700 °C. The samples were characterized by XRD, SEM, TEM, and HRTEM, respectively. The results indicate that the powders exhibit a granular shape of 80 nm in diameter. It is believed that the nanosize of as-prepared PSN powders is dependent on the well-dispersed performance, which arouse from the combined effects of both precipitant TMAH and surfactant CTAB. The mechanism of the formation of the pure perovskite PSN nanopowders is discussed in detail. Our method is expected to create a new, low-cost route to produce the promising nanopowders of multi-component perovskite systems.     

Investigation of 4H—SiC metal—insulation—semiconductor structure with Al2O3/SiO2 stacked dielectric

Atomic layer deposited (ALD) Al₂O₃/dry-oxidized ultrathin SiO₂ films as high-k gate dielectric grown on the 8° off-axis 4H-SiC (0001) epitaxial wafers are investigated in this paper. The metal-insulation-semiconductor (MIS) capacitors, respectively with different gate dielectric stacks (Al₂O₃/SiO₂, Al₂O₃, and SiO₂) are fabricated and compared with each other. The I-V measurements show that the Al₂O₃/SiO₂ stack has a high breakdown field ( ≥ 12 MV/cm) comparable to SiO₂, and a relatively low gate leakage current of 1× 10^-7 A/cm² at electric field of 4 MV/cm comparable to Al₂O₃. The 1-MHz high frequency C-V measurements exhibit that the Al₂O₃/SiO₂ stack has a smaller positive flat-band voltage shift and hysteresis voltage, indicating less effective charge and slow-trap density near the interface.     

A new high-pressure polymorph of Ti2O3: implication for high-pressure phase transition in sesquioxides

The post-corundum phase transition has been investigated in Ti₂O₃ on the basis of synchrotron X-ray diffraction in a diamond anvil cell and transmission electron microscopy. The new polymorph of Ti₂O₃ was found at about 19 GPa and 1850 K, and this phase was stable even at about 40 GPa. A new polymorph of Ti₂O₃ can be indexed on a Pnma orthorhombic cell, and the unit-cell parameters are a=7.6965 (19) Å, b=2.8009 (9) Å, c=7.9300 (23) Å, V=170.95 (15) Å³ at 19 GPa, and a=7.8240 (2) Å, b=2.8502 (1) Å, c=8.1209 (3) Å, V=181.10 (1) Å³ at ambient conditions. The Birch–Murnaghan equation of state yields K ₀=206 (3) GPa and K′₀=4 (fixed) for corundum phase, and K ₀=296 (4) GPa and K′₀=4 (fixed) for the post-corundum phase. The molar volume decreases by 12% across the phase transition at around 20 GPa. The structural identification was carried out on a recovered sample by the Rietveld method, and a new polymorph of Ti₂O₃ can be identified as Th₂S₃-type rather than U₂S₃-type structure. The transition from corundum-type to Th₂S₃-type structure accompanies the drastic change of the form of polyhedron: from TiO₆ octahedron in the corundum-type to TiO₇ polyhedron in the Th₂S₃-type structures.     

Synthesis of spherical LiNi1/3Co1/3Mn1/3O2 cathode materials for Li-ion batteries

Spherical LiNi_1/3Co_1/3Mn_1/3O₂ was successfully prepared by controlled crystallization. The preparation started with the spherical coprecipitate of Ni_1/3Co_1/3Mn_1/3CO₃ from NiSO₄, CoSO₄, MnSO₄, NH₄HCO₃, and NH₃·H₂O, followed by pyrolysis of Ni_1/3Co_1/3Mn_1/3CO₃ at 600°C for 3 h. The X-ray diffraction analysis showed that the homogeneous cubic (Ni_1/3Co_1/3Mn_1/3)₃O₄ was obtained after the pyrolysis. Spherical LiNi_1/3Co_1/3Mn_1/3O₂ was obtained by sintering of the mixture of as-obtained (Ni_1/3Co_1/3Mn_1/3)₃O₄ and LiOH·H₂O at 900°C for 6 h in air. As-prepared spherical LiNi_1/3Co_1/3Mn_1/3O₂ presented initial discharge capacity of 162.9 mA h g⁻¹ and capacity retention of 98% at 50th cycle.     

Study of electrical conductivity changes and phase transitions in Co3O4 doped ZrO2

The electrical conductivity of ZrO₂ doped with Co₃O₄ has been measured at various temperatures for different molar ratios. The conductivity increases due to the migration of vacancies created by doping. The conductivity is also found to increase with rise in temperature up to 120°C, and after attaining a maximum the conductivity decreases due to a collapse of the lattice framework. A second rise in conductivity around 460°C in all the compositions confirms the phase transition in ZrO₂ from monoclinic to tetragonal symmetry. X-ray powder diffraction and DTA studies were carried out for confirming the doping effects and the transition in ZrO₂.     

Structural and dielectric studies of lead-free ceramics: Na1/2Y1/2TiO3

The polycrystalline samples of Na_1/2Y_1/2TiO₃ were prepared by the mixed-oxide method. A preliminary X-ray structural analysis was shown to exhibit the formation of a single-phase compound with an orthorhombic structure. Microstructural analysis by scanning electron microscopy (SEM) exhibits well defined grains distributed uniformly through out the sample suggesting the compactness and homogeneity of the sample. Detailed studies of dielectric properties of Na_1/2Y_1/2TiO₃ in a wide frequency range (102–106 Hz) at different temperatures (31–500°C) show a dielectric anomaly at 105°C, which may be related to a ferroelectricparaelectric phase transition as suggested by hysteresis loop at room temperature. An ac conductivity (σ _ac) of the material is mainly governed by the polaron hopping mechanism, which is also influenced by both frequency and temperature. The activation energy was obtained from the plot of temperature with a.c. conductivity.      

Preparation of TiO<Subscript>2</Subscript>-coated LiCo<Subscript>1/3</Subscript>Ni<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> by electrostatic self-assembly method and its properties

A precursor of TiO₂–LiCo_1/3Ni_1/3Mn_1/3O₂ was prepared by electrostatic self-assembly method. The final product was obtained by heating the precursor at 400–450 °C for 4–6 h in air. X-ray diffraction (XRD), scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), and electrochemical tests were used to examine the structural, morphology, elementary valence, and electrochemical characteristics. XRD indicated that the TiO₂-coated material can be indexed by α-NaFeO₂ layered structure, which belongs to hexagonal-type space group R3m. XPS results confirmed the existence of TiO₂ compound on the surface of the coated sample. The SEM image showed that the material had spherically porous morphology with the uniform size about 6 μm. The initial charge–discharge capacity of the TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ material was 168.8/160.0 mAh/g. After 60 cycles, the discharge capacity of the TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ sample was 147.0 mAh/g, and the coulombic efficiency was 94.0%. Compared with the uncoated sample, the electrochemical performance of TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ was improved.     

Effects of O2/Ar ratio and annealing temperature on electrical properties of Ta2O5 film prepared by magnetron sputtering

The effects of the oxygen-argon ratio on electric properties of Ta2O5 film prepared by radio-frequency magnetron sputtering were investigated.The Ta2O5 partially transforms from the amorphous phase into the crystal phase when annealing temperatures are 800℃ or higher.The lattice constant of Ta2O5 decreases with the increase of the O2/Ar ratio,which indicates that oxygen gas in the working gas mixture contributes to reducing the density of oxygen vacancies during the deposition process.For the films deposited in working gas mixtures with different O2/Ar ratios and subsequently annealed at 700℃,the effective dielectric constant is increased from 14.7 to 18.4 with the increase of the O2/Ar ratio from 0 to 1.Considering the presence of an SiO2 layer between the film and the silicon substrate,the optimal dielectric constant of Ta2O5 film was estimated to be 31.Oxygen gas in the working gas mixture contributes to reducing the density of oxygen vacancies,and the oxygen vacancy density and leakage current of Ta2O5 film both decrease with the increase of the O2/Ar ratio.The leakage current decreases after annealing treatment and it is minimized at 700℃.However,when the annealing temperature is 800℃ or higher,it increases slightly,which results from the partially crystallized Ta2O5 layer containing defects such as grain boundaries and vacancies.     

第一原理研究Sn(O1-xNx)2材料的光电磁性质

基于第一原理的密度泛函理论, 以量子化学从头计算软件 为平台研究了Sn(O_1-xN_x)₂材料的光电磁性能, 分析了体系的态密度、 能带结构、 磁性、 介电虚部及折射率. 计算结果表明, N替代O后, 随着掺杂浓度的增加, 体系的带隙先减小后增大, 掺杂量为12.50%时带隙最窄. 由于N 2p轨道电子的贡献, 在0.55-1.05 eV范围内产生了浅受主能级, 价带和导带处的能级均出现了劈裂及轨道的重叠现象, Sn-O键的键强大于N-O键的键强. 从磁性来看, N原子决定了磁矩的大小. 从介电虚部可知, 掺杂后体系的光学吸收边增宽, 主跃迁峰发生红移, 反射率和介电谱相对应, 各峰值与电子的跃迁吸收有关.     

Study of Crystal Structure of Polypropylene/Mg2B2O5 Whisker Composite

The effects of whisker content, sample holding time, and differential scanning calorimetry (DSC) analysis of the crystal structure of polypropylene/Mg ₂ B ₂ O ₅ whisker composites were investigated. DSC shows a double melting peak, T ₁ at about 151°C and T ₂ at about 166°C. Detailed analysis of wide angle X-ray diffraction (WAXD) shows that a γ phase may exist in the polypropylene/Mg ₂ B ₂ O ₅ composite. The experimental results also show that the crystal structure according to MPLT (melting peak at low temperature) was more perfect and the crystallinity according to MPLT increased with increasing whisker content. The sample holding time at room temperature following injection molding had a significant effect on the number of γ -crystal nuclei.