脊形掺铒Al2O3光波导放大器级联特性的模拟计算

利用有限元法分析了脊形掺铒Al₂O₃光波导放大器内信号光和抽运光的场模式分布、速率方程求解铒离子五能级系统的粒子数分布.数值模拟了光波导净增益与信号光功率的关系和多个放大器级联的净增益特性.结果表明：级联系统存在着净增益亏损.低掺铒浓度的光波导作前级放大器的组合方式,级联系统总净增益最大.     

集成光学 光电集成与器件

TN256 2005053606 侧蚀对脊形掺铒光波导放大器净增益的影响=Simulation for the net gains of rib Er-doped waveguide amplifiers and effect of side-sculpture on the net gains[刊,中]／李成仁(辽 宁师范大学物理系．辽宁,大连(116029)),宋昌烈…∥半 导体光电．-2005,26(1)．-14-18,21 用限元方法分析了脊形掺铒Al2O3光波导放大器内 部信号光和泵浦光的电磁场模式分布,结合速率方程和传 输方程,数值模拟了脊形Er:Al2O3光波导放大器的净增 益特性,讨论了光波导侧蚀对放大器净增益的影响。图10 参14(严寒)     

C波段50 MW行波输出速调管设计

设计了导流系数1.53 P的电子枪,枪内场强低于22.1 kV/mm,阴极平均负载小于6.3 A/cm2;采用部分屏蔽流均匀场电磁聚焦系统,实现了对电子注的良好聚焦;设计了C波段/2模盘荷波导行波输出结构,采用CST软件对其色散特性、耦合阻抗进行了计算分析。首先以单间隙输出腔代替行波输出结构对5腔注-波互作用系统进行计算,确定了前4腔的设计参数,然后采用PIC模拟软件对具有盘荷波导结构的输出系统进行了三维模拟,获得了大于50 MW的输出功率,效率大于45%,饱和增益大于50 dB,盘荷波导结构间隙电压比单间隙输出腔下降30%,效率提高4%。     

阶跃掺杂Er∶Al_2O_3光波导放大器增益特性数值模拟

构建了纵向阶跃非均匀掺杂的掺铒Al2O3光波导放大器理论模型,利用有限元法、速率方程和传输方程,数值模拟了放大器的净增益特性·计算结果表明阶跃掺杂掺铒Al2O3光波导放大器提高了抽运效率,净增益和信号光输出功率比优化后的均匀掺杂光波导放大器分别提高了9.2%和90.5%,长度却缩短了16.9%.     

阶跃掺杂Er∶Al2O3光波导放大器增益特性数值模拟

构建了纵向阶跃非均匀掺杂的掺铒Al2O3光波导放大器理论模型,利用有限元法、速率方程和传输方程,数值模拟了放大器的净增益特性.计算结果表明：阶跃掺杂掺铒Al2O3光波导放大器提高了抽运效率,净增益和信号光输出功率比优化后的均匀掺杂光波导放大器分别提高了9.2%和90.5%,长度却缩短了16.9%.     

阶跃掺杂Er∶Al2O3光波导放大器增益特性数值模拟

构建了纵向阶跃非均匀掺杂的掺铒Al2O3光波导放大器理论模型,利用有限元法、速率方程和传输方程,数值模拟了放大器的净增益特性.计算结果表明:阶跃掺杂掺铒Al2O3光波导放大器提高了抽运效率,净增益和信号光输出功率比优化后的均匀掺杂光波导放大器分别提高了9.2%和90.5%,长度却缩短了16.9%.     

345 GHz折叠波导行波管中电磁传输损耗的分析计算

利用电导率等效方法对345GHz折叠波导行波管中的电磁信号的传输损耗进行了仿真研究,考察了流通管孔径、加工粗糙度等对冷腔传输损耗的影响。结果表明,流通管孔径较大或加工粗糙度较大都会导致电磁信号传输严重衰减。模拟分析了热腔中电磁信号衰减对慢波结构净增益、带宽、最佳周期数等器件特征参数的影响,结果显示,电磁信号衰减会使得增益下降和带宽降低。     

镱铒共掺Al2O3光波导放大器的净增益特性

将中频磁控溅射方法沉积制备的镱铒共掺Al2O3薄膜刻蚀成矩形截面、直线通道的光波导放大器.测量了净增益与抽运功率的关系,结果表明：净增益随抽运功率近似线性增加,阈值抽运功率为18 mW;抽运功率为68 mW时,长2.24 cm 的光波导放大器净增益为8.44 dB.数值模拟结果显示,相同抽运功率下的净增益为10.6 dB.     

带状注速调管高频结构的初步研究

 利用3维软件设计并模拟了适用于X波段高功率带状注速调管的“Ⅱ”形谐振腔,根据模拟结果分析了腔体各尺寸对电场均匀性的影响;建立了平面对称结构的3维高频互作用系统模拟平台,应用此平台讨论了扼流器法和漂移管窄壁开槽法这两种抑制漂移管中非工作模式的方法;分析了漂移管的尺寸及漂移头对谐振腔内场分布的影响。研究表明：波导高度、耦合腔宽度和高度对带状注速调管谐振腔间隙的电场均匀性影响较大;而波导长度和宽度、耦合腔长度对该电场均匀性影响不大;腔体连接处加上漂移头可使场分布更加集中;该型带状注速调管谐振腔能够产生均匀的电场,为提高注波互作用效率奠定了基础。     

用于自由电子激光的S波段J型波导馈电加速管

随着波导式耦合行波加速管设计梯度的日益提高,为了防止加速管输入耦合器电场的横向动量在束流通过加速器耦合器时引起束流品质的下降,侧壁开有两个对称耦合孔的对称双馈圆柱腔获得了广泛的应用。研制的S波段J型波导馈电加速管即为双馈圆柱腔中的一种,研制样管在老练平台上老练时的最高加速梯度达到30 MV/m。然而因为四极场的存在,开有两个耦合孔的圆柱耦合腔内,仍然会引起轴向电场的幅度和相位在横向的梯度,从而使束流发射度变差。在理论上对J型波导馈电的跑道式耦合腔进行了研究,通过与圆柱腔进行比对模拟计算,证明跑道式耦合器可以很好地改善轴向电场在横向平面内非近轴区域沿圆周的场强一致性,从而减小四极场的影响。重要的是,J型波导馈电跑道式耦合腔的机械加工、测试比圆柱腔更加容易实现,是未来双馈加速器发展的一个理想方向。     

氧碘化学激光中的增益光导效应

 发现和分析了氧碘化学激光中的增益光导效应。碘注入的不均匀等导致增益在该方向的不均匀。采用预混模型和Fabry Perot腔模型，推导了碘不均匀分布情况下的单重态氧的产额和激光束横向分布的解析表达式。计算结果表明，由于增益光导效应，引起激光横向分布的变化，可导致光束在碘注入方向的倾斜，以及输出功率的下降。     

X波段高功率高增益多注相对论速调管放大器设计

针对器件工程应用中的高功率高增益需求,设计了工作在X波段的高功率高增益多注相对论速调管放大器,建立了带输入、输出波导结构的三维整管模型。设计双边对称耦合孔输入腔结构,降低了输入波导对输入腔间隙电场均匀性的影响以抑制非均匀干扰模式;设计采用多腔多间隙群聚结构,降低了输入微波功率的需求,提高了器件放大增益;并且分析设计了多间隙扩展互作用微波提取结构,提高了器件的功率转换效率以及降低输出结构表面电场强度。通过优化设计,粒子模拟仿真实现X波段多注相对论速调管放大器输出微波功率达到3.2 GW,器件放大增益约为60 dB,功率转换效率约为40%。器件验证实验在电子束电压550 kV,电流5.1 kA的情况下,输出功率为0.99 GW,放大增益约为53 dB,转换效率约为35%。     

Controlled optical switching based on dipole-induced transparency in a cavity–waveguide system

We show that one can control the path of an optical field propagating in a waveguide with another optical field in a cavity–waveguide system. The strong coupling between the two optical fields is achieved using cavity–QED based on dipole-induced transparency and an optical Stark shift. Numerical simulations suggest that the optical switching is possible even when the intensity of the control field approaches the single photon level.     

Flat-topped beam output from a double-clad rectangular dielectric waveguide laser with a high-index inner cladding

A novel method to produce a flat-topped laser beam by using a double-clad rectangular waveguide laser with high-index inner cladding is presented. The waveguide dispersion equation for cosine mode was deduced, the condition for the flattened mode was given out, relative gains for guided modes were calculated numerically and analyzed. Results indicate that a gain advantage for the flattened mode is clear, a flat-topped laser beam can be achieved when the optical confinement factor, the gain intensity and the output coupler are chosen suitably.     

Optical ratchets with discrete cavity solitons

We propose a setup to observe soliton ratchet effects using discrete cavity solitons in a 1D array of coupled waveguide optical resonators. The net motion of solitons can be generated by an adiabatic shaking of the holding beam with zero average inclination angle. The resulting soliton velocity can be controlled by different parameters of the holding beam.     

Optical cavity coupled surface plasmon resonance sensing for enhanced sensitivity

A surface plasmon resonance (SPR) sensing system based on the optical cavity enhanced detection tech-nique is experimentally demonstrated. A fiber-optic laser cavity is built with a SPR sensor inside. By measuring the laser output power when the cavity is biased near the threshold point, the sensitivity, defined as the dependence of the output optical intensity on the sample variations, can be increased by about one order of magnitude compared to that of the SPR sensor alone under the intensity interrogation scheme. This could facilitate ultra-high sensitivity SPR biosensing applications. Further system miniaturization is possible by using integrated optical components and waveguide SPR sensors.     

Finite element analysis of optically controlled non-linear directional coupler switches

Optically controlled two-way optical switches are useful for high-speed photonic switches and rapidly reconfigurable optical interconnection networks. A directional coupler forms such a switch because the field can be switched from one waveguide to the other by altering the optical length of the waveguide. Nonlinear materials are incorporated in the waveguide so that the optical path length may be altered by using an optical control beam to vary the intensity of light. A finite element method is described that enables the modelling of the non-linear dual waveguide structure for arbitrary waveguide shapes. Spurious modes are avoided in the transverse magnetic field method and non-linearity is handled by iteration and assuming an equivalent non-linear relative permittivity.     

亮孤子在宇称时间对称波导中的传输和控制

基于光波在宇称-时间(PT)对称波导中传输的理论模型, 数值研究了亮孤子在呈高斯分布的PT对称克尔非线性平板波导中的传输和控制. PT对称波导, 要求波导的折射率分布呈偶对称, 而增益/损耗分布呈奇对称. 结果表明: 当波导的折射率分布强度为正时, PT对称波导的中心折射率最大, 即使没有自聚焦克尔非线性效应, PT对称波导也可以束缚光波, 形成波浪形光束且长距离传输; 当折射率分布强度为负时, PT对称波导的中心折射率最小, 光波的传输方向发生偏移. 而增益/损耗分布可控制光波的偏移方向: 增益/损耗分布强度为正, 光波向左偏移; 强度为负, 光波向右偏移; 强度为零时, 光波被分为两束. 且当折射率分布强度为负时, 可以很好地抑制相邻亮孤子间的相互作用. 该研究结果可为未来PT对称波导在全光控制方面的应用提供一定的理论依据.     

Polarization of radiation under superradiance conditions

A theoretical study is made of the polarization properties of superradiance emitted by gases in a high-current longitudinal discharge. It is shown that the Zeeman effect in the discharge current makes the radiation at the periphery of a light beam totally polarized. Formulas are derived for relating the degree of polarization of a light beam with the dependences of the gain profile on the frequency and on the transverse coordinate. An analysis is made of the influence of diffraction on the polarization properties of a light beam and the anisotropic waveguide modes are found. A calculation is made of the distribution of the intensity of the optical field when radiation is generated between crossed Polaroids at the exit end of the discharge tube.Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Fizika, No. 5, pp. 51–56, May, 1980.The authors are grateful to A. I. Odintsov and V. P. Yakunin for frequent discussions.     

双光力诱导透明窗口的可调特性

提出一个杂化腔光力系统理论方案,利用两纳米机械振子间的库仑耦合作用实现弱探测光的双光力诱导透明窗口.研究边带可分辨区域和红失谐情况下双光力诱导透明窗口的可调特性.数值计算表明:两纳米振子间的库仑作用可有效地使单光力诱导透明窗口劈裂为双透明窗口.随着库仑耦合强度的增大,两透明窗口间的距离对称性地拉大;其次,光力腔衰减率的改变对两透明窗口的位置和深度无影响,仅对两透明窗口的宽度产生细微改变,测量精度可在坏腔情形下得到很好的保持;另外,仅增加参量放大器的非线性增益参量将使两透明窗口变宽,而引入驱动参量放大器的光场相位,利用相位匹配可以产生比空腔情形更加狭窄陡峭的双透明窗口,可用于比空腔情况更加精密的测量.