微波消解-石墨炉原子吸收光谱法测定污水厂污泥和进、出水中的镉、铅

建立了微波消解–石墨炉原子吸收光谱法测定污水处理厂进出水和污泥中重金属Cd,Pb的方法。分别向污水样品中加入5.0 mL硝酸,污泥样品中加入4.0 mL硝酸和2.0 mL双氧水,放入微波消解炉中进行消解。消解好的样品用1%NH_4H_2PO_4作为基体改进剂,在0.5%HNO_3介质中采用塞曼扣除背景,石墨炉程序升温方式进行Cd,Pb的原子化,用石墨炉原子吸收光谱法测定Cd,Pb的含量。Cd,Pb的质量浓度分别在0~2.00μg/L,0~40.0μg/L范围内与其吸收峰高呈良好的线性关系,线性相关系数分别为0.999 1,0.999 6。Cd,Pb检出限分别为0.104 9,0.394 5μg/L,测定结果的相对标准偏差分别为1.34%~3.61%,2.12%~2.80%(n=11),加标回收率分别为98.2%~102.6%,94.0%~100.4%。该方法简单,高效,结果准确度高,重现性好,适用于污水处理厂的进出水和污泥中重金属铅和镉的检测。     

微波消解–石墨炉原子吸收法测定药食两用中药材中的铅

建立测定药食两用中药材中铅含量的微波消解–石墨炉原子吸收光谱分析方法。样品经微波消解后,以2%磷酸二氢铵为基体改进剂,用石墨炉原子吸收法测定药食两用中药材中的铅含量。在2~40μg/L范围内,铅的质量浓度与吸光度呈良好的线性关系,线性相关系数r大于0.999,检出限为5μg/kg。加标回收率为94.0%~105.5%,测定结果的相对标准偏差小于5.0%(n=6)。该方法操作简便快速,准确度较高,基体干扰小,适合药食两用中药材中铅的检测。     

微波消解–石墨炉原子吸收法测定化妆品中的铅

建立了微波消解–石墨炉原子吸收光谱法测定化妆品中铅的方法。探讨了样品前处理条件、基体改性剂的选择和优化、石墨炉升温条件等对测定结果的影响。在优化的试验条件下,铅的质量浓度在0~100 ng/mL范围内与吸光度具有良好的线性关系,线性相关系数r=0.9991,检出限为0.33 ng/mL。用该法对5种化妆品中的铅进行测定,加标回收率在95.0%~106.1%之间,测定结果的相对标准偏差不大于3.6%。该方法可应用于化妆品中痕量铅的分析。     

微波消解-石墨炉原子吸收光谱法分析测定食用菌中总砷

摘 要：采用微波消解-石墨炉原子吸收光谱法分析测定食用菌中总砷。取可食部分的食用菌粉碎均匀,采用微波消解对样品进行消解,将消解液于140℃赶酸至0.5mL ,用超纯水转移定容至25mL。以0.1%的硝酸钯为基体改进剂,塞曼扣背景,用石墨炉原子吸收光谱法测定总砷。方法检出限为0.4μg/L,线性范围为0~30 μg/L,线性相关系数(r)大于0.998,采用精密度考察方法重现性,不同浓度水平的RSD%均小于6.6%;三个浓度水平的加标回收率为80.6% ~ 103.9%,有证标准物质测定结果符合要求。实验结果表明,方法操作简便、灵敏、准确,适合食用菌中总砷的测定。对砷形态复杂的野生食用菌,微波消解后可直接采用石墨炉原子吸收光谱法测定总砷。     

超级微波消解－石墨炉原子吸收光谱法测定香菇中的镉

为建立一种快速批量检测香菇中镉的方法,建立了超级微波消解－石墨炉原子吸收光谱法测定香菇中镉含量的方法。分别采用湿法消解、普通微波消解和超级微波、传统微波和湿法消解技术前处理香菇标准物质样品,对比消解效果,优化超级微波消解技术的酸体系和消解最终温度。;采用石墨炉原子吸收光谱仪法测定,优化基体改进剂、灰化温度等工作参数,确定仪器最佳检测条件,验证分析方法的准确性和稳定性。结果表明,超级微波消解优于湿法消解和传统微波消解技术,准确性和重复性最佳,大幅减少用酸量的同时更加安全、高效,避免样品污染。在最优分析方法条件下,镉在0~4.0 μg/L范围内所得回归方程线性关系良好,相关系数(R)为0.9994,方法检出限为0.001 mg/kg,精密度RSD为1.4%~2.5%。超级微波消解－石墨炉原子吸收光谱法检测的探索与应用超级微波消解优于湿法消解和传统微波消解技术,大幅减少用酸量的同时更加安全、高效,避免样品污染,为农产品镉含量批量检测提供可靠的方法支撑。     

微波消解–石墨炉原子吸收光谱法测定84消毒剂中的痕量铅

建立了84消毒剂中痕量铅的微波消解–石墨炉原子吸收光谱测定方法。84消毒液以硝酸为消解试剂,用微波消解法进行消解。用2%磷酸二氢铵为基体改进剂,在优化后的仪器工作条件下测定。铅的质量浓度在0~80.0ng/mL范围内与吸光度呈良好的线性关系,线性相关系数r=0.999 3,方法检出限为0.005 4 mg/kg,平均回收率为94.66%,测定结果的相对标准偏差为1.87%(n=6)。该方法灵敏度与准确度高,可用于84消毒剂中痕量铅的检测。     

超级微波消解-石墨炉原子吸收光谱法测定不同类型土壤中的镉

采用超级微波消解仪对样品进行前处理,对比不同消解体系的消解效果,选择合适的消解体系,采用石墨炉原子吸收光谱法测定镉浓度,同时优化基体改进剂、灰化温度等工作参数,确定最佳的分析条件。探讨并建立超级微波消解-石墨炉原子吸收光谱法测定不同类型土壤镉含量的方法。在最优条件下,标准曲线在0～1.0μg/L浓度范围内线性关系良好,相关系数r=0.999,检出限浓度为0.04μg/L,定量限浓度为0.12μg/L,方法准确度为94.5%～110%,相对标准偏差RSD为0.60%～5.4%,方法应用于不同类型土壤标准物质镉的测定,测得结果均在标准值范围内。方法简便快捷、准确高效、用酸量低、节约环保,便于在基层推广,适用于批量处理不同类型镉污染土壤样品。     

微波消解-石墨炉原子吸收光谱法测定黄芩中铅

建立了微波消解-石墨炉原子吸收法测定黄芩中铅的方法。在最佳工作条件下,用微波消解处理样品,铅的回收率为97.3%~100.7%,方法的精密度和准确度均能满足检测的要求。     

微波消解-原子吸收光谱法测定口红中的铅、汞

建立了微波消解–原子吸收光谱法测定口红中铅、汞的方法。以微波消解装置进行口红样品预处理,以石墨炉原子吸收光谱法进行铅含量测定,以冷原子吸收光谱法进行汞含量测定。铅在0.00～2.50 mg/L范围内的线性方程为y=0.022 3x+0.000 8,r=0.999 3,检出限为0.003 mg/L。汞在0～500 ng/L范围内的线性方程为y=400.12x+52.3,r=0.999 9,检出限为6 ng/L。铅、汞测定结果的相对标准偏差分别为0.87%～2.6%,0.65%～2.41%(n=6),加标回收率分别为121%～126%,100%～102%。该方法以单消解方式进行样品前处理,再以该消解液分别进行两种元素含量分析,可提高分析效率,适用于化妆品中金属含量分析。     

石墨炉原子吸收光谱法测定新疆出口番茄酱中的铅和镉

报道了微波消解石墨炉原子吸收光谱法测定番茄酱中的铅、镉。研究了石墨炉原子吸收测定的最佳条件。该方法测定铅和镉的线性范围分别为0.00~25 ng/mL、0.00~8 ng/mL;相对标准偏差分别为2.15%、3.10%;回收率分别为98.6%、104.5%。利用国家标准物质番茄叶(ESP-1)验证了方法的准确度,测定值与标准值基本吻合。研究表明,该方法具有很好的准确度和精密度。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.