Removal, preconcentration and determination of Mo(VI) from water and wastewater samples using maghemite nanoparticles

Removal and recovery of Mo(VI) from aqueous solutions were investigated using maghemite (γ-Fe₂O₃) nanoparticles. Combination of nanoparticle adsorption and magnetic separation was used to the removal and recovery of Mo(VI) from water and wastewater solutions. The nanoscale maghemite with mean diameter of 50 nm was synthesized by reduction coprecipitation method followed by aeration oxidation. Various factors influencing the adsorption of Mo(VI), e.g. pH, temperature, initial concentration, and coexisting common ions were studied. Adsorption reached equilibrium within <10 min and was independent of initial concentration of Mo(VI). Studies were performed at different pH values to find out the pH at which maximum adsorption occurred. The maximum adsorption occurred at pHs between 4.0 and 6.0. The Langmuir adsorption capacity (q_max) was found to be 33.4 mg Mo(VI)/g of the adsorbent. The results showed that nanoparticle (γ-Fe₂O₃) is suitable for the removal of Mo(VI), as molybdate, from water and wastewater samples. The adsorbed Mo(VI) was then desorbed and determined spectrophotometrically using bromopyrogallol red as a complexation reagent. This allows the determination of Mo(VI) in the range 1.0–86.0 ng mL⁻¹.     

Structural analysis of several W(VI) and Mo(VI) complex perovskites prepared by the polymeric precursors method

We describe in this work the synthesis by the Pechini method of five Mo(VI)- and W(VI)-containing complex perovskites and their structural characterisation by HREM and XRD. The compounds studied, Ba(B_2/3′B_1/3″)O₃ (B′=In and Y; B″=W and Mo) and Sr(In_2/3W_1/3)O₃, were obtained after firing the precursor powders for 8 h at 1200°C. Thermal analysis showed that the formation mechanism of the five perovskites is similar and implies the formation of barium carbonate and barium tungstates or molybdates of different stoichiometries as intermediate phases. Interesting enough, these similar mechanisms yield to materials of a quite different structure. Indeed, Ba(In_2/3Mo_1/3)O₃ and Sr(In_2/3W_1/3)O₃ were found to be disordered perovskites (unit cells: a_p×a_p×a_p and , respectively); on the other hand, two phases coexist in the sample Ba(In_2/3W_1/3)O₃ at the synthesis conditions: an ordered predominant phase (unit cell: 2a_p×2a_p×2a_p) and, as a minor phase, a disordered perovskite (unit cell: a_p×a_p×a_p). Finally, the two yttrium-containing compounds were found to be ordered perovskites (2a_p×2a_p×2a_p).     

Direct voltammetric determination of Mo(VI) in plants: the need for a multivariate study of interferences

A multivariate modelling procedure using a second order composite design showed that the adsorptive stripping voltammetry (AdSV) technique used for molybdenum determination in a N,N-dimethylformamide (DMF)-ethanol-water homogeneous ternary solvent system (HTSS) using α-benzoinoxime (αBO) as the complexing agent and a sodium acetate-acetic acid buffer as the supporting electrolyte is much more tolerant to the presence of phosphorous (as phosphate) and iron than it could be presumed. Instead of the concentration ratios of P/Mo=100 and Fe/Mo=500, determined by univariate experiments, these values were respectively raised to 97,500 and 4200 when the phosphate and Fe(III) levels are varied simultaneously from 0.625 to 2.500 and from 0.006 to 0.150 mg l⁻¹, respectively, in the voltammetric cell, keeping the molybdenum concentration constant at 3.00 μg l⁻¹. This allowed us to propose a straightforward AdSV-HTSS procedure for the determination of Mo(VI) in plants. The AdSV results compared favourably with those obtained by using graphite furnace atomic absorption spectrometry (GFAAS) and with the results of samples from the International Plant-Analytical Exchange (IPE) programme of Wageningen University (The Netherlands).     

Catalytic spectrophotometric determination of molybdenum (VI) with the hydrazine-metanil yellow system

A new catalytic Spectrophotometric method for the determination of trace amounts of molybdenum (VI) has been proposed. The method is based on the catalytic effect of Mo(VI) on the reduction of metanil yellow by hydrazine dihydrochloride. Under experiment condition, the linear range of determination is 20–160 ng/mL for molybdenum and the detection limit is 11.2ng/mL. The method has been used to determine trace molybdenum in bean samples with the recovery of 96.0–99.0%, with relative standard deviations of 1.50–2.53%.     

Selective spectrophotometric determination of palladium(II) with 2(5-nitro-2-pyridylazo)-5-(N-propyl-N-3-sulfopropylamino)phenol(5-NO(2).PAPS) and tartaric acid with 5-NO(2).PAPS-niobium(V) complex

Spectrophotometric determinations of palladium(II) and tartaric acid were respectively investigated by using the color reactions between 2(5-nitro-2-pyridylazo)-5-(N-propyl-N-3-sulfopropylamino)phenol(5-NO₂.PAPS) and palladium(II) in strong acidic media, and between 5-NO₂.PAPS, niobium(V) tartaric acid in weak acidic media. The calibration graphs were linear in the range of 0–25 μg/10 ml palladium(II), with an apparent molecular coefficient () of 6.2×10⁴ l mol⁻¹ cm⁻¹ at 612 nm, and 0–23 μg/10 ml tartaric acid with =1.08×10⁶ l mol⁻¹ cm⁻¹ at 612 nm, respectively. The proposed methods were selective and sensitive in comparison with other chelating pyridylazo dyes–palladium(II) or metavanadic acid–tartaric acid method, and the effect of foreign ions such as copper(II) was negligible for the assay of palladium(II) with 5-NO₂.PAPS.     

Kinetic Determination of Nanogram Amounts of Mo(VI) in Solution

A new inhibitory reaction is proposed and a kinteic method developed for the determination of ultra‐micro amounts of Mo(VI) on the basis of its inhibitory activity in oxidation of trimethylenediamine ‐N,N,N′,N′‐tetraacetic acid (TDTA) by KMnO₄ in the presence of hydrochloric acid. Under optimal conditions the sensitivity of the method is 0.5 ng/cm³. The probable relative error is 2.9–3.5% for the concentration range 7.5–2.0 ng/cm³ of Mo(VI). The effect of certain foreign ions upon the reaction rate were determined for the assessment of the selectivity of the method. The selectivity of the method is relatively good. Kinetic equations were proposed for the investigated process. A method has been applied for determination of Mo(VI) in a certain kind of steel.     

A new experimental approach for liquid-liquid extractive spectrophotometric determination of chromium(VI) in tannery wastewater and alloy samples

In this research work, a new approach is developed for the extractive determination of chromium. The principle of this approach is based on the complexation reaction between 4-(4?-chlorobenzylideneimino)-3-methyl-5-mercapto-1,2,4-triazole (CBIMMT) in dichloromethane as a complexing reagent and chromium(III) in presence of potassium iodide to form a yellow coloured complex at room temperature. The 1:2:2 [Cr(III)-CBIMMT-iodide] ternary complex was quantitatively extracted in dichloromethane from 2.5 mol L^?1 of hydrochloric acid medium which showed maximum absorption intensity at λ_max 411 nm and was stable for more than 72 h. The values of molar absorption coefficient and Sandell’s sensitivity of the complex were found to be 0.7019 × 10⁴ L mol^?1 cm^?1 and 0.00748 µg cm^?2, respectively. The system adheres to Beer’s law from 1.5 to 6.0 µg mL^?1; however, Ringbom’s plot suggests optimal concentration range was 1.8–5.8 µg mL^?1. The limit of detection and limit of quantification of the approach is 0.26 and 0.79 µg mL^?1. This approach was successfully used for the determination of chromium from wastewater effluents from the tannery industries (Kolhapur, MS, India), alloy samples and for separation of it from synthetic mixtures. The present experimental approach is apparently much simpler than the conventional method comprising multistep processes.     

Simultaneous determination of Fe(II) and Fe(III) by kinetic spectrophotometric H-point standard addition method

The H-point standard addition method (HPSAM) for simultaneous determination of Fe(II) and Fe(III) is described. The method is based on the difference in the rate of complex formation of iron in two different oxidation states with Gallic acid (GA) at pH 5. Fe(II) and Fe(III) can be determined in the range of 0.02–4.50 μg ml⁻¹ and 0.05–5.00 μg ml⁻¹, respectively, with satisfactory accuracy and precision in the presence of other metal ions, which rapidly form complexes with GA under working conditions. The proposed method was successfully applied for simultaneous determination of Fe(II) and Fe(III) in several environmental and synthetic samples with different concentration ratios of Fe(II) and Fe(III).     

Sensitive and selective determination of gallic acid in green tea samples based on an electrochemical platform of poly(melamine) film

In this work, an electrochemical sensor coupled with an effective flow-injection amperometry (FIA) system is developed, targeting the determination of gallic acid (GA) in a mild neutral condition, in contrast to the existing electrochemical methods. The sensor is based on a thin electroactive poly(melamine) film immobilized on a pre-anodized screen-printed carbon electrode (SPCE*/PME). The characteristics of the sensing surface are well-characterized by field emission scanning electron microscopy (FE-SEM), X-ray photoelectron spectroscopy (XPS) and surface water contact angle experiments. The proposed assay exhibits a wide linear response to GA in both pH 3 and pH 7.0 phosphate buffer solutions (PBS) under the optimized flow-injection amperometry. The detection limit (S/N = 3) is 0.076 μM and 0.21 μM in the pH 3 and pH 7 solutions, respectively. A relative standard deviation (RSD) of 3.9% is obtained for 57 successive measurements of 50 μM GA in pH 7 solutions. Interference studies indicate that some inorganic salts, catechol, caffeine and ascorbic acid do not interfere with the GA assay. The interference effects from some orthodiphenolic compounds are also investigated. The proposed method and a conventional Folin–Ciocalteu method are applied to detect GA in green tea samples using the standard addition method, and satisfactory spiked recoveries are obtained.     

Application of a ternary complex of tungsten(VI) with 4-nitrocatechol and thiazolyl blue for extraction-spectrophotometric determination of tungsten

A new ternary ion-association complex of tungsten(VI), 4-nitrocatechol (NC), and 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (Thiazolyl Blue, MTT) was obtained and studied using an extraction-spectrophotometric method. The optimum pH, reagent concentrations, and extraction time were determined. The composition of the complex was found to be W(VI): NC: MTT = 1: 2: 2. The extraction process was investigated quantitatively and the key constants were calculated. The molar absorptivity of the chloroform extract at λ_max = 415 nm was 2.8 × 10⁴ dm³ mol⁻¹ cm⁻¹, and the Beer’s law was obeyed up to 8.8 μg cm⁻³ tungsten(IV). The limit of detection and limit of quantification were calculated to be 0.27 μg cm⁻³ and 0.92 μg cm⁻³, respectively. The effect of foreign ions and reagents was studied and a competitive method for determination of tungsten in products from ferrous metallurgy was developed. The residual standard deviation and the relative error were 0.53 % and 0.2 %, respectively.     

Preparation of soluble ternary heteroazo dye complexes for the spectrophotometric determination of trace uranium(VI)

The complexing ability of typical pyridylazo, quinolylazo and thiazolylazo dyes with uranium(VI) in aqueous ethanol media are investigated in the presence and absence of aromatic carboxylic acid. Uranium(VI) forms solubilized ternary complexes with PAN, PAR, TAM, 5-Br-PADAP, 3,5-diBr-PADAP and QADAP in 48% ethanol solution containing sufficient amounts of sulfosalicylic acid and triethanolamine buffer (pH 7.8). Aromatic carboxylic acids contribute to expel the coordinated water molecules from the uranium (VI) moiety and their chelating effects have been explained by ternary complex formation. An increase in molar absorptivity and no shift in the wavelength of maximum absorbance are observed for all uranium(VI) complexes investigated. The 11 stoichiometry of uranuim(VI) and heteroazo dye in the binary complex does not change through ternary complex formation. The molar absorptivity of the uranium(VI)-3,5-diBr-PADAP-sulfosalicylic acid ternary complex at 595 nm is 8.4×10⁴l mol^–1 cm^–1 and Beer's law is valid up to 2.5gmg ml^–1 of uranium(VI). The interferences due to coexisting metal ions can be effectively masked by addition of CyDTA or Ca-CyDTA.     

Aminothiozolyl maleamic acid based multi chelating hydrogels for the separation of uranium (VI) ions from aqueous environment

Multi chelating hydrogels (MCHs) were synthesized using a simple radical polymerization method from acrylamide, hydroxyethyl acrylate, and N‐(2‐aminothiozolyl)maleamic acid (AMA) monomers, methylenebisacrylamide (MBA) a cross‐linker, and azobisisobutyronitrile (AIBN) an initiator. The resulting MCHs were characterized with Fourier transform infrared spectroscopy and scanning electron microscopy to confirm the formation and morphological properties. The MCHs were highly swellable in aqueous solutions as well as different pH conditions. MCHs were applied to evaluate uptake behavior of Uranium (VI) ion from aqueous solutions. Batch adsorption studies were performed by varying experimental conditions like contact time, pH, and initial metal ion concentration. The kinetics data was best suited with the second‐order equation model. The equilibrium adsorption data was correlated with Langmuir and Freundlich isotherm models. This study suggests that maximum Uranium (VI) ion uptake has been found to be 288 mg.g^?1 and regenerated for 5 cycles without any significant change. Copyright © 2016 John Wiley & Sons, Ltd.     

Analysis of interferents by means a D-optimal screening design and calibration using partial least squares regression in the spectrophotometric determination of Cr(VI)

Using a central composite design, the signal of the process for the spectrophotometric determination of hexavalent chromium (λ = 543 nm) is maximised and its variability minimised using as complexing agent 1,5-diphenylcarbazide in sufficiently acid medium. To analyse the interference of various analytes (Mo(VI), V(V), Fe(III) and Mn(VII)) on the Cr(VI) as a function of concentration of interferent, a factorial design was prepared at three levels of each (zero, medium and high concentration), which implies performing 81 determinations. However, a D-optimal design with just nine experiments is sufficiently good to estimate the model proposed.The interference of these metals makes it impossible to determine Cr(VI) when they are present in the sample. To avoid prior separation steps, a multivariate regression by partial least squares, PLS, is proposed to calibrate the Cr(VI) in the presence of these analytes varying the concentration of the Cr(VI) between 0.1 and 0.9 μg ml⁻¹ and that of the interferents between 3 and 5 μg ml⁻¹. The average errors obtained were 4.5% and 3.29% fitted and in prediction, respectively, with a standard error in prediction (RMSEP) of 0.016% presenting absence of both constant and proportional bias.The detection limit with the PLS regression in the presence of interferents is 0.1 μg ml⁻¹ with a probability of false positive equal to 5% and less than 5% for false negative. The capability of detection is similar to that obtained with the univariate calibration (absorbance at 543 nm) in absence of interferents.With the PLS regression it is possible to discriminate 0.085 μg ml⁻¹ of Cr(VI) in a sample with 0.5 μg ml⁻¹ of Cr(VI) with probabilities of false compliance and false non-compliance equal to 0.05. For the univariate calibration without interferents, it was established at 0.0971 μg ml⁻¹ of Cr(VI) for the same nominal concentration.In relation to interference of V(V), Fe(III) and Mn(VII), the PLS calibration could be an efficient alternative to the separation step for Cr(VI) spectrophotometric determination using 1,5-diphenylcarbazide.     

Synthesis,characterization and crystal structure of a dioxomolybdenum(VI) complex with a N,O type bidentate Schiff base ligand as a catalyst for homogeneous oxidation of olefins

The synthesis of a Mo(VI) Schiff base complex, cis-[MoO₂{(4,6-bis(tert-butyl)-2-{(benzyl)iminomethyl}phenolate)₂}], cis-[MoO₂(L)₂] where L = 4,6-bis(tert-butyl)-2-{(benzyl)iminomethyl}phenol, derived from benzylamine and 3,5-di-tert-butylsalycilaldehyde is reported. Full characterization of this complex was accomplished with elemental analyses, spectroscopic studies (NMR, IR and electronic) and X-ray structure analysis. This complex was tested as a catalyst for the homogeneous oxidation of olefins. The Mo(VI) complex is catalytically active for the epoxidation of aliphatic substrates at 80 °C, yielding the epoxide as the sole product in yields up to 100% and turnover numbers up to 5000. Under the optimized conditions styrene was oxidized in an 81% conversion to produce styrene oxide, benzaldehyde, and acetophenone.     

On the determination of low nitrogen concentration gradients in austenitic CrNi(Mo) steels

For the determination of diffusion coefficients by using the model diffusion into a plate methodical examinations were carried out on samples of austenitic steel that had been nitrided in their marginal zones for 1.5 h at 1523 K.For recording of the concentration of N as a function of the distance from the surface electron-probe microanalysis (EPMA) and the precision determination of the lattice parameters by Kossel technique were applied. Both methods yield comparable results.     

A study of the spectrophotometric method for the determination of uranium(VI) in trialkylamine/kerosene extracts using 1-(2-pyridylazo)-2-naphthol

Summary The Spectrophotometric method for the determination of uranium(VI) in trialkylamine extracts using 1-(2-pyridylazo)-2-naphthol (PAN) as a colorimetric reagent has been examined. The Job and Mole Ratio methods suggest that the coloured product is a 11 complex of uranium and PAN. The method can be applied to cover the concentration range 0 to 5 g uranium per litre of extract. Sulphate interference is eliminated in the method by removal with calcium ions before colour development. Interferences from other ions likely to be present in the aqueous liquor appear to arise largely from inhibition of the uranium partition into the amine phase.

---

Untersuchung der spektralphotometrischen Uran(VI)-Bestimmung in Trialkylamin/Kerosin-Extrakten mit Hilfe von 1-(2-Pyridylazo)-2-naphthol

Zusammenfassung Das Verfahren, bei dem ein Uran-PAN-Komplex der Zusammensetzung 11 gebildet wird, kann für einen Konzentrationsbereich von 0 bis 5 g U pro l Extrakt eingesetzt werden. Eine Störung durch Sulfat wird durch dessen Entfernung mit Calciumionen vor der Farbentwicklung verhindert. Störungen durch andere Ionen werden hauptsächlich durch Beeinflussung der Uranextraktion hervorgerufen.

     

Potential of ethylenediaminedi(o-hydroxyphenylacetic acid) and N,N'-bis(hydroxybenzyl)ethylenediamine-N,N'-diacetic acid for the determination of metal ions by capillary electrophoresis

Two aromatic polyaminocarboxylate ligands, ethylenediaminedi(o-hydroxyphenylacetic acid) (EDDHA) and N,N′-bis(hydroxybenzyl)ethylenediamine-N,N′-diacetic acid (HBED), were applied for the separation of transition and heavy metal ions by the ion-exchange variant of electrokinetic chromatography. EDDHA structure contains two chiral carbon centers. It makes it impossible to use the commercially available ligand. All the studied metal ions showed two peaks, which correspond to meso and rac forms of the ligand. The separation of metal–HBED chelates was performed using poly(diallyldimethylammonium) polycations in mixed acetate–hydroxide form. Simultaneous separation of nine single- and nine double-charged HBED chelates, including In(III), Ga(III), Co(II)–(III) and Mn(II)–(III) pairs demonstrated the efficiency of 40 000–400 000 theoretical plates. The separation of Co(III), Fe(III) complexes with different arrangements of donor groups and oxidation of Co(II), Mn(II), Fe(II) ions in reaction with HBED have been discussed.     

A simple flow injection spectrophotometric determination method for iron(III) based on O-acetylsalicylhydroxamic acid complexation

A simple and rapid flow-injection spectrophotometric method for the determination of iron(III) and total iron is proposed. The method is based on the reaction between iron(III) and O-acetylsalicylhydroxamic acid (AcSHA) in a 2 % methanol solution resulting in an intense violet complex with strong absorption at 475 nm. Optimum conditions for the determination of iron(III) and the interfering ions were tested. The relative standard deviation for the determination of 5 μg L⁻¹ iron(III) was 0.85 % (n = 10), and the limit of detection (blank signal plus three times the standard deviation of the blank) was 0.5 μg L⁻¹, both based on the injection volumes of 20 μL. The method was successfully applied in the determination of iron(III) and total iron in water and ore samples. The method was verified by analysing a certified reference material Zn/Al/Cu 43XZ3F and also by the AAS method.     

Studies on the mixed-ligand complexes of copper(II) with gallic acid and pyridine carboxylic acids and their benzologues

Summary The ternary complex formation of copper(II) with gallic acid (gal) and 2-hydroxy nicotinic acid (hyna), 2-mercapto nicotinic acid (mena), salicylic acid (sa) or thiosalicylic acid (tsa) as a second ligand in a 1:1:1 molar ratio has been investigated in 40% (v/v) ethanol using spectrophotometric andpH titration methods. The solution equilibria of the ternary systems have been determined and the stability constants of the mixed complexes has been evaluated. Considering all parameters, the Cu-gal-sa ternary system was proved as a suitable, rapid, and sensitive spectrophotometric indicator for determining traces of copper.The ternary system containingsa obeysBeer's law up to 3.4 µg·ml^–1 copper. The optimum range for the determination of copper (Ringbom) atpH 6.0 ranges from 0.63 to 1.74 µg·ml^–1 of copper. The molar absorptivity of the ternary complex is 1.3×10⁴l·mol^–1·cm^–1.

---

Untersuchungen anmixed-ligand — Komplexen von Kupfer(II) mit 3,4,5-Trihydroxybenzoesäure und Pyridincarbonsäuren und ihren C-Homologen

Zusammenfassung Die Bildung ternärer Komplexe von Kupfer(II) mit 3,4,5-Trihydroxybenzoesäure (gal) und 2-Hydroxynicotinsäure (hyna), 2-Mercaptonicotinsäure (mena), Salicylsäure (sa) oder Thiosalicylsäure (tsa) in einem molaren Verhältnis von 1:1:1 wurde mittels spektrophotometrischer und potentiometrischer Methoden in 40% (v/v) Ethanol untersucht. Die Lösungsgleichgewichte der termären Systeme und die Stabilitätskonstanten der gemischten Komplexe wurden bestimmt. Unter Berücksichtigung aller Parameter erwies sich das termäre System Cu-gal-sa als geeigneter schneller und empfindlicher Indikator zur Spurenanalyse von Kupfer.Dassa enthaltende ternäre System gehorcht demBeerschen Gesetz bis zu einer Kupferkonzentration von 3.4 µg·ml^–1. Der optimale Bereich zur Bestimmung von Kupfer (Ringbom) beipH 6.0 erstreckt sich von 0.63 bis 1.74 µg Cu pro ml. Die molare Extinktion des ternären Komplexes beträgt 1.3×10⁴l·mol·cm^–1.