CO2激光作用下运动石英玻璃的温度分布

研究了运动石英玻璃板在CO2激光作用下的热效应,在考虑表面辐射和空气对流的情况下建立了数学模型,采用有限元软件ANSYS进行数值计算,得到了运动情况下石英玻璃的温度分布。比较了激光功率、光斑半径和运动速度对温度分布的影响,得到了温度分布与运动速度和激光参数之间的关系。结果显示石英玻璃板的表面温度随激光功率的增加而增加,随光斑半径、运动速度的增加而减小。     

CO2激光器五种混合气体压强优化

 应用遗传算法,以输出激光功率为目标函数,优化确定了普通CO₂激光器五种工作气体（CO₂, N₂, He, Xe, H₂）的最佳充气量。对1.2m长谐振腔,在15kV放电条件下,优化的充气量分别为p_CO2=1.15×133.3Pa, p_N2=7.32×133.3Pa, p_He=12.95×133.3Pa, p_Xe=0.36×133.3Pa和p_H2=0.01×133.3Pa。优化后激光功率比未优化前可提高1.27倍。     

CO2激光对熔石英表面小尺寸损伤的修复

 利用10.6 μm的CO₂激光对不同直径的点状损伤和不同宽度的划痕进行了修复。经过波长351 nm的紫外激光考核发现,对于直径小于80 μm的点状损伤和对于宽度小于40 μm的划痕,随着损伤点尺寸和划痕宽度的增加,修复后阈值提高程度逐渐降低。划痕的宽度在达到40 μm以后修复效果非常微弱。修复过程中,由于作用时间较短及温度分布不均产生了热应力导致样片损伤以后产生径向裂痕,后续的紫外激光会使裂痕明显扩展。当样品被置于高温退火炉内退火3 h以后,应力导致开裂的现象得到了解决。     

CO2连续激光对单晶硅电池的辐照效应

 研究了CO₂激光对单晶硅太阳能电池的辐照效应,并对其损伤机理进行了分析。在激光功率密度较低而不能使电池产生物理损伤时,电池的性能会因在被辐照过程中温度的升高而产生暂时性降低;当激光功率密度高到使电池产生物理损伤时,电池的输出性能便产生永久下降。通过对比激光辐照前后电池伏安特性曲线和输出功率曲线的变化情况,结合对损伤形貌的分析,表明：当电池被物理损伤之后,电池的性能会出现大幅度下降,硅PN结的严重烧蚀破坏是主要原因。     

Ag-Cu纳米颗粒修饰的N掺杂TiO2纳米棒阵列及其高效光催化CO2还原应用

本文采用微纳加工方法制备了负载高密度Ag-Cu纳米颗粒的N掺杂TiO₂纳米棒阵列样品. 通过TiO₂的N掺杂,可将其吸光范围调控至与Ag纳米颗粒的等离激元吸收频率相匹配的波段,从而实现复合材料中肖特基结与共振能量转移过程的协同作用. 与此同时,Cu纳米颗粒可以为CO₂还原提供活性位点. 在全谱光照射下,复合样品光催化CO₂还原的活性显著提高,CH₄生成速率可达720 μmol·g^-1·h^-1.     

TEA CO2激光器非对称电极系统的电场分布

 设计了一种非对称电极,这种非对称电极的阳极是Chang电极或Ernst电极,阴极是由直线和圆弧构成的简单电极。通过比较和分析非对称电极和对称电极的特点发现,非对称电极系统中简单电极的边缘电场起伏最大。采用有限元方法计算了非对称电极系统中的简单电极取不同的直线长度和弧线半径时,非对称电极系统的电场分布,给出了选择非对称电极系统中的简单电极参数的依据。结果表明：这种非对称电极系统结合了解析电极和简单电极的优点,通过选择非对称电极系统的简单电极参数,它可以在TEA CO₂激光器中产生边缘电场起伏小于0.06,且满足电极表面均匀场面积宽度要求的电场。     

脉冲激光沉积温度及氧压对Bi2Sr2Co2Oy热电薄膜晶体结构与电输运性能的影响

利用脉冲激光沉积技术在c-Al₂O₃单晶基片上制备了Bi₂Sr₂Co₂O_y热电薄膜并研究了沉积温度和氧压对薄膜晶体结构及电输运性能的影响.在最佳沉积条件下制备的单相、c轴取向的Bi₂Sr₂Co₂O_y薄膜的室温电阻率ρ和塞贝克系数S分别为2.9mΩ/cm和110μupV/K,其功率因子S²/ρ好于在单晶样品上得到的值.此外,该薄膜在低温下表现出较强的负磁阻效应,在2K,9T时达到了40%.     

高功率TEA CO2激光器两波长激光切换输出技术

 以TEA CO₂激光器通常采用的平-凹光学稳定腔为基础,提出了一种新的波长选支方法——输出窗口镀膜选支方法。利用一台高平均功率TEA CO₂激光器进行了选支实验研究,结合现有光学镀膜技术,得到了中心波长为9.3 μm的激光单谱线输出,其单脉冲能量及平均功率与激光器原中心波长10.6 μm单谱线输出的相应参数基本相当。研究发现,以相同单脉冲能量激光照射热敏纸时,中心波长9.3 μm激光光斑与中心波长10.6 μm的明显不同。同时,还设计出两波长窗口密闭免调切换装置,在一台激光器上实现了10.6,9.3 μm两个中心波长激光同等功率水平的免调切换输出,切换位置误差小于5″,密封性能满足使用要求。     

TEA CO2激光器序列带的输出特性

 采用双光栅谐振腔和增长放电增益区,进行了TEA CO₂激光器弱线输出特性研究。在CO₂,N₂,He气体体积比为0.16∶0.21∶0.63,总压强为57.3 kPa情况下,获得6条11 μm波长附近弱线(序列带和热带)激光输出,谱线脉宽为400 ns左右。研究了011-030带的P19线的输出波形和能量,结果表明：谱线输出能量随光栅中心的位移变化而变化,当光栅中心在放电区中心轴线上时输出最强,最大输出能量达几百mJ。     

1.315μm附近CO2的高分辨率吸收光谱

 利用可调谐激光长程吸收光谱测量系统，记录到1.315μm附近高气压（80kPa和40kPa）CO₂的高分辨率吸收光谱，拟合分析获得谱线参数，结果与HITRAN 2k的数据基本一致。用程差法测量了绝对吸收，氧碘激光频率(7 603.138 5cm^-1)的总吸收截面为(0.23~0.29)×^-24cm²。仅计算谱线吸收的吸收截面为0.18×10^-24cm²。在1.315μm波段COCO₂存在连续吸收，吸收截面为(0.05~0.11)×10^-24cm²。还讨论了测量误差问题。     

Temperature prediction for CO2 laser heating of moving glass rods

This paper presents a heat transfer model to calculate the temperature field in moving glass rods heated by a CO₂ laser. Conduction and radiation heat transfer in radial and axial directions are taken into account in the current model. The Rosseland diffusion approximation is incorporated to analyze the radiation heat transfer in the glass rod. A two-band model is used to simulate the spectral property of the glass. Results of the simulation show that glass rods of sufficiently large optical thickness should be treated as a semitransparent medium for radiative transfer, and it is reasonably accurate to assume it to be opaque to CO₂ laser irradiation. It has been shown that the resulting temperature profile is strongly dependent on the laser parameters, i.e., the size of laser beam and the power of the laser. The diameter and speed of the moving glass rod are also important in determining the temperature field although the convective heat transfer coefficient between the glass rod and the environment has little effect.     

Temperature field distribution in multi-layered solid media heated with multi-modes laser beam

In the present paper we want to develop an analytical model to study the thermal behavior of multi-layered solid media in interaction with a laser beam. We suppose that each layer has a constant thermal conductivity. We consider that the laser beam is formed by decoupled [Phys Rev A 1996; 53: 4435] multi-modes Hermite–Gauss beams. The model is applied using the classical heat equation which was solved using the integral transform method [Infrared Phys Technol 2002; 42: 31; Optics Laser Technol 2004; 36: 219–22; Optics Laser Technol 2004; 36: 677–9; Proc SPIE 2003; 5227: 323].     

Passive Q switching by heated CO2

Passive Q switching using heated CO₂ as a saturable absorber was observed. A kinetic model previously proposed is used to interpret this phenomenon. Our study reveals the important role of rotational and vibrational relaxation mechanisms.     

Temperature distribution in a film heated with a laser spot: Theory and measurement

For the measurement of the thermal capacity and the thermal conductivity of films, the thermal excitation of the sample is commonly performed by the absorption of light. This results in a spatial and temporal temperature distribution within the film. With a variety of methods static or dynamic temperature recordings are performed.Two problems with these methods are discussed, the calculation of the temperature distribution in the film and the measurement of the mean surface temperature of the film. An analytical solution of the heat conduction problem for a cylindrical geometry with any radial distribution of the absorbed light is given. Resistive bolometers are introduced for the measurement of the mean surface temperature of the film within a circular area. Experiments with a 25 m thick PVDF film give excellent agreement with the theoretical calculations within the modulation frequency range 10^–3 Hz to 10³ Hz, thus allowing a determination of various thermal parameters of the investigated film.     

Power density distribution of a commercial CO2 laser

Translated from Zhurnal Prikladnoi Spekstroskopii, Vol. 51, No. 5, pp. 762–766, November, 1989.