Formation and characterization of natural polysaccharide hollow nanocapsules via template layer-by-layer self-assembly

Two different natural zeolites having different phase compositions were obtained from different regions of Turkey and modified by ion-exchange (0.5M NH(4)NO(3)) and acid leaching using 1M HCl. The natural and modified samples were treated at low temperature (LT), high temperature (HT) and steam (ST) conditions and characterised by XRF, XRD, BET, FTIR, DR-UV-Vis, NH(3)-TPD and TGA. Ion-exchange with NH(4)(+) of natural zeolites results in the exchange of the Na(+) and Ca(2+) cations and the partial exchange of the Fe(3+) and Mg(2+) cations. However, steam and acidic treatments cause significant dealumination and decationisation, as well as loss of crystalline, sintering of phases and the formation of amorphous material. The presence of mordenite and quartz phases in the natural zeolites increases the stability towards acid treatment, whereas the structure of clinoptilolite-rich zeolites is mostly maintained after high temperature and steam treatments. The natural and modified zeolites treated at high temperature and in steam were found to be less stable compared with synthetic zeolites, resulting in a loss of crystallinity, a decrease in the surface area and pore volume, a decrease in the surface acidity as well as dealumination, and decationisation.     

天然气与硫酸盐热化学还原反应的模拟实验研究

为探讨天然气中高含量硫化氢形成的化学机制，利用高温高压反应装置，对天然气与固态硫酸钙反应体系进行了热模拟实验研究。使用气相色谱仪、微库仑仪、傅里叶变换红外光谱仪和X射线衍射仪对产物进行了分析，探讨了硫酸盐热化学还原反应的热力学特征，并进行了反应动力学研究。结果表明，高温下天然气与固态硫酸钙可以发生反应，产物主要为硫化氢、二氧化碳、碳酸钙、水和炭。热力学研究表明，天然气与固态硫酸钙的反应可行，升高温度对反应有利，同一温度下长链烷烃与固态硫酸钙发生反应的可能性要比短链烷烃大。根据动力学模型得到反应活化能为96.824kJ/mol。     

A study of chemical composition and radiation attenuation properties in clinoptilolite-rich natural zeolite from Turkey

Clinoptilolite, a type of natural zeolite, has been commonly used as pozzolanic additive in concrete. This type of natural zeolite is generally used as a mineral admixture by substitution in Portland cement to produce high performance concretes. In the present study, the major, minor and trace element levels present in the clinoptilolite-rich natural zeolite (CRNZ) have been determined using a wavelength dispersive X-ray fluorescence spectrometer. Also, the clinoptilolite-rich natural zeolite has been compared with Portland cement with respect to the radiation attenuation properties. From the results it can be concluded that due to the natural radioactive content of clinoptilolite-rich natural zeolite (CRNZ) even if it is in trace level and also due to the poorer X-ray attenuation compared with Portland cement, special care should be taken to use this type of natural zeolite as blend materials in cements, etc.     

Selective Sorption of Fe(III) Ions from Ni(II)-Fe(III) Mixtures with Chemisorbents

Selective recovery of Fe(III) ions from two-component nitrate solutions of Fe(III) and Ni(II) with synthetic nickel phosphate, natural chalk, and natural tripoli were studied. The mechanism of selective action of chemisorbents was considered, and high efficiency of the materials considered was demonstrated.     

Modeling thermodynamic properties of natural gas mixtures using perturbed-chain statistical associating fluid theory

Perturbed-Chain Statistical Associating Fluid Theory (PC-SAFT) was employed for predicting thermodynamic properties of natural gas mixture. Thermodynamic properties like density, isobaric and isochoric heat capacity, enthalpy, entropy, and internal energy were calculated with the PC-SAFT. Results are validated against experimental data for natural gas and mixtures similar to natural gas. The validation show that the Average Absolute Deviation (AAD) for density is 1.10% for binary mixture and 1.08% for mixtures similar to natural gas. Also AAD value for enthalpy is 1.42%, for internal energy, 0.77, for entropy, 0.43, for isochoric heat capacity, 1.26%, and for isobaric heat capacity, 2.66%. Results show PC-SAFT to be able to predict all the thermodynamics properties of natural gas and mixtures similar to natural gas with high accuracy in a wide range of temperature and pressure.     

Tuning methane content in gas hydrates via thermodynamic modeling and molecular dynamics simulation

Storage and transportation of natural gas as gas hydrate (“gas-to-solids technology”) is a promising alternative to the established liquefied natural gas (LNG) or compressed natural gas (CNG) technologies. Gas hydrates offer a relatively high gas storage capacity and mild temperature and pressure conditions for formation. Simulations based on the van der Waals–Platteeuw model and molecular dynamics (MD) are employed in this study to relate the methane gas content/occupancy in different hydrate systems with the hydrate stability conditions including temperature, pressure, and secondary clathrate stabilizing guests. Methane is chosen as a model system for natural gas. It was found that the addition of about 1% propane suffices to increase the structure II (sII) methane hydrate stability without excessively compromising methane storage capacity in hydrate. When tetrahydrofuran (THF) is used as the stabilizing agent in sII hydrate at concentration between 1% and 3%, a reasonably high methane content in hydrate can be maintained (∼85–100, v/v) without dealing with pressures more than 5 MPa and close to room temperature.     

Free-radical-mediated conjugate additions. Enantioselective synthesis of butyrolactone natural products: (-)-enterolactone, (-)-arctigenin, (-)-isoarctigenin, (-)-nephrosteranic acid, and (-)-roccellaric acid

Lewis acid-mediated conjugate addition of alkyl radicals to a differentially protected fumarate 10 produced the monoalkylated succinates with high chemical efficiency and excellent stereoselectivity. A subsequent alkylation or an aldol reaction furnished the disubstituted succinates with syn configuration. The chiral auxiliary, 4-diphenylmethyl-2-oxazolidinone, controlled the stereoselectivity in both steps. Manipulation of the disubstituted succinates obtained by alkylation furnished the natural products (-)-enterolactone, (-)-arctigenin, and (-)-isoarctigenin. The overall yields for the target natural products were 20-26% over six steps. Selective functionalization of the disubstituted succinates obtained by aldol condensation gave the paraconic acid natural products (-)-nephrosteranic acid (8) and (-)-roccellaric acid (9). The overall yield of the natural products 8 and 9 over four steps was 53% and 42%, respectively.     

Comparison of purification processes of natural gas obtained from three different regions in the world

Natural gases obtained from different regions in the world as Scholen-Germany, Saudi Arabia and Iran were purified with a package code and the obtained results were compared in this study. For purification process, both natural gases flowing in a vertical pipe and monoethanolamine (MEA) flowing as a film from the internal surface of a pipe were examined together. Both fluids were flown in a vertical and laminar regime. Binary diffusion coefficients, Schmidt numbers (Sc) and dynamical viscosities were calculated individually for three types of natural gases. It is demonstrated that the chemical absorption method by MEA process is the most appropriate method at high Damko¨hler (Da) numbers particularly for natural gases containing high concentrations of CO2 and H2S.     

高效液相色谱-质谱法分离鉴定天然红心鸭蛋黄中的红色素

采用薄层色谱、高效液相色谱-质谱-质谱(HPLC-MS-MS)及高分辨电子轰击质谱(EI-MS)方法,分离鉴定了天然红心鸭蛋（简称红心蛋）蛋黄中红色素的分子组成和结构。以甲醇-水(体积比为99.5∶0.5)为流动相,用C18柱从红心蛋的红色素中分离出4个峰。光电二极管阵列检测器(PDA)扫描图显示,4个峰均为单峰,最大吸收波长分别为482,488,496,501 nm。HPLC-MS-MS分析结果表明,红心蛋中的红色素的各个峰具有相同的相对分子质量(Mr=562),其二级质谱具有紫杉紫素(rhodoxan     

Structural requirements for efficient cellular photoprotection by carotenoid derivatives

We have synthesized five carotenoid derivatives: (1) Girard's reagent P (GRP)-retinal from GRP and retinal; (2) GRP-carotenal from GRP and beta-apo-8'-carotenal; (3) Girard's reagent T (GRT)-carotenal from GRT and beta-apo-8'-carotenal; (4) (GRP2-canthaxanthin from 2 mol of GRP and 1 mol of canthaxanthin; and (5) dansyl hydrazine (DH)-carotenal from DH and beta-apo-8'-carotenal. The first three derivatives are cations, whereas the fourth is a dication and the fifth is a weak base. Using K562 cells, we compared the subcellular distribution of the synthetic carotenoid derivatives with two uncharged natural carotenoids, beta-carotene and beta-apo-8'-carotenal. The two natural carotenoids were present mainly within the cell membranes. The synthetic carotenoid derivatives were more broadly distributed among the cell organelles. The positively charged derivatives had relatively high concentrations in mitochondria, whereas DH-carotenal had a relatively high concentration in lysosomes. We also measured the amount of photoprotection provided by the synthetic and natural carotenoids for K562 cells labeled with a photosensitizer (hypericin, protoporphyrin IX or cis-di[4-sulfonatophenyl]diphenylporphine). In this model system, only carotenoid derivatives with a permanent positive charge provided significant photoprotection. Neither the two natural carotenoids nor DH-carotenal were effective photoprotectors.     

毛细管电泳结合高效液相色谱-质谱用于天然产物活性成分的筛选

发展了毛细管电泳(CE)和高效液相色谱-质谱(HPLC-MS)相结合的用于天然产物中活性成分筛选和鉴定的方法。该方法中,用HPLC半制备柱对天然产物粗提物进行分离纯化,再用CE对HPLC纯化后的组分进行活性测试。根据HPLC-MS/MS提供的二级质谱数据,即可确定活性成分的化学结构。以乙酰胆碱酯酶为实验模型,对我们发展的筛选方法进行了验证。从黄连粗提物中确定了药根碱、巴马汀等7种活性成分,并通过CE测定了它们的半抑制率(IC₅₀)值。与传统的天然产物分离纯化和活性筛选方法相比,该方法具有简单、微量、快速、准确的优点。本文建立的方法为天然产物粗提物中活性成分的筛选提供了新技术。     

Determination of boron isotopic variations in aquatic systems with negative thermal ionization mass spectrometry as a tracer for anthropogenic influences

A technique for precise boron isotope ratio measurements with a high detection power has been developed by negative thermal ionization mass spectrometry (NTIMS). Relative standard deviations in the range of 0.03-0.3% have been obtained for the determination of the (11)B/(10)B isotope ratio using nanogram amounts of boron. Ba(OH)(2) has been applied as ionization promoter for the formation of negative thermal ions. By adding MgCl(2) better reproducibilities of the measurement have been achieved. A possible interference of BO(-)(2) ions at mass number 42 by CNO(-) could be excluded by the sample preparation technique used. Contrary to other NTI techniques no dependence of the measured isotope ratio on the boron amount used has been observed. Anthropogenic and natural saline influences in ground water have been successfully identified by boron isotope ratio determinations with this NTIMS method, due to the different isotopic composition of boron in natural and anthropogenic substances. In sewage, the boron isotope ratio is substantially influenced by washing powder, which contains low (11)B/(10)B ratios (expressed in delta(11)B values normalized to the standard reference material NIST SRM 951). In contaminated ground water, low delta(11)B values are normally correlated with high boron and high chloride concentrations. On the other hand, delta(11)B shifts to higher values in less contaminated samples. For ground water with saline influences, only the delta(11)B determination, and not the boron or chloride content, allowed the correct identification of this natural source of contamination.     

Analysis of luminescence spectra of leucite (KAISiO4).

High-sensitivity radioluminescence (RL) and thermoluminescence (TL) measurements were carried out on samples of natural leucite (with 2.95% of Na2O) from Campania Vessa (Italy). Samples were annealed to modify the charge compensation through alkali metal self-diffusion and to produce luminescence centres. High-temperature powder diffraction, scanning electron microscopy and chemical analyses were performed to monitor the tetragonal-cubic phase transitions and the thermal drainage of alkali metal ions from the aluminosilicate lattice. The emission spectral bands of leucite (300, 380, 430, 480, 560 and 680 nm) match those of other Na/K-aluminosilicates (alkali metal feldspars) and could be attributed to similar defects. TL glow curves of increasingly pre-irradiated natural leucite (range 0-20 Gy) showed no changes above 300 degrees C, whereas some changes were observed with annealed samples (1000 degrees C for 12 h). This temperature is the starting point of Na self-diffusion within the aluminosilicate lattices. The areas of the TL glow curves of both natural and annealed beta-irradiated leucites can be fitted with a linear function with high correlation. These results are in agreement with high alkali metal loss (K2O approximately 12% and Na2O approximately 18%) during thermal pre-treatment, high cell volume expansion (from 2350 to 2500 A) and the cubic la3d reversible tetragonal I4l/a phase transition. This promotes the egress of alkali metal ions and the production of [AlO4/M+]o, [AlO4/H+]o and [AlO4]o luminescence centres.     

Highly diastereoselective synthesis of beta-carboxy-gamma-lactams and their ethyl esters via Sc(OTf)(3)-catalyzed imino Mukaiyama-aldol type reaction of 2,5-bis(trimethylsilyloxy)furan with imines

Functionalized gamma-lactams are found to be crucial intermediates in the synthesis of biologically important natural products. We herein described a highly diastereoselective synthesis of beta-carboxy-gamma-lactams and their ethyl ester derivatives, in high yields with high diastereomeric ratio, via the Mukaiyama-aldol type reaction of 2,5-bis(trimethysilyloxy)furan with imines, employing Sc(OTf)(3) as a catalyst.     

Fast‐Geomimicking using Chemistry in Supercritical Water

Herein we introduce a powerful and fast method to produce nanominerals using a bottom up approach. The supercritical hydrothermal flow synthesis is exploited to produce model nanominerals by mimicking natural environments at high temperatures under pressure. This innovative concept is demonstrated with the talc synthesis; this represents a major technical breakthrough since it allows decreasing the mineral‐synthesis time from tens of hours to tens of seconds. Through this example, we show these nanominerals exhibit new crystal‐chemistry signals and new properties. This approach provides a means to reproduce the early stages of formation of minerals in different natural environments from sedimentary environments (low temperature and pressure) to hydrothermal/metamorphic environments (high temperature and high pressure).     

Preparation of Graphene by Using an Intense Cavitation Field in a Pressurized Ultrasonic Reactor

A new and efficient method to produce a large quantity of high‐quality and non‐oxidized graphene flakes from powdered natural graphite by using a high‐intensity cavitation field in a pressurized ultrasonic reactor is demonstrated. TEM and selected‐area electron diffraction (SAED) confirmed the ordered graphite crystal structure of graphene. Atomic force microscopy (AFM) was used to examine the thickness of the graphene sheets. The delamination (exfoliation) of natural graphite in the liquid phase depends on the physical effects of ultrasound, which break down the 3D graphite structure into a 2D graphene structure. The prepared graphene is of high purity and without defects because no strongly oxidizing chemicals are used and no toxic products result. TEM shows that graphene nanosheets were produced with sizes in the range of tens to hundreds of square nanometers; these nanosheets were smooth and without any ripples and corrugations. High‐resolution TEM (HRTEM) and SAED analysis confirmed that the products were graphene nanosheets.     

Regioselective nucleophilic 1,4-trifluoromethylation of 2-polyfluoroalkylchromones with (trifluoromethyl)trimethylsilane. Synthesis of fluorinated analogs of natural 2,2-dimethylchroman-4-ones and 2,2-dimethylchromenes

Reactions of 2-polyfluoroalkylchromones with (perfluoroalkyl)trimethylsilanes proceed as a 1,4-nucleophilic perfluoroalkylation to give 2,2-bis(polyfluoroalkyl)chroman-4-ones with high regioselectivity and good yields after acid hydrolysis. Oxidation of 6-methyl-2,2-bis(trifluoromethyl)chroman-4-one with a mixture of K2S2O8 and CuSO4 in aqueous acetonitrile leads to fluorinated analogues of natural lactarochromal and the corresponding acid. Reduction of substituted 2,2-bis(trifluoromethyl)chroman-4-one with sodium borohydride in methanol and subsequent dehydration of chromanols in refluxing xylene in the presence of p-toluene sulfonic acid gives 2,2-bis(trifluoromethyl)chromenes, which are fluorinated analogues of natural precocenes.     

Adsorption of Am(III) on red earth and natural hematite

Summary The Am(III) adsorption isotherms on natural hematite, on a red earth and on three kinds of treated red earth samples were determined and compared. The treatment was performed to remove iron oxides, organic matter (OM) and both. The batch technique and aqueous Am(III) solutions with molarities less than 3 ^. 10^-9 mol/l were used. A very high adsorbability of Am(III) on hematite was found, and in order to decrease the adsorption percentage, stable Eu³⁺ as a hold back carrier was added to the aqueous solution. All the isotherms were found to be linear. The strong effects of pH, ionic strength and fulvic acid (FA) on the Am(III) adsorption on natural hematite were demonstrated. A positive contribution of OM and an unexpectedly high negative influence of iron oxides on the Am(III) adsorption by the untreated red earth were found too. The average distribution coefficients of Am(III) adsorption on natural hematite, on red earth and on three kinds of treated red earth samples were determined, respectively, from these linear isotherms. The very high adsorbability of Am(III) on hematite and the very strong negative influence of iron oxides on the Am(III) adsorption on untreated red earth were distinctly demonstrated as well. It appears that the adsorbability of composed natural materials cannot be predicted from the adsorbabilities of each of the mineral components alone, due to possible interactions between the mineral components and the different characteristics of the composite.     

Access to polyfunctionalized diquinanes, hydrindanes, and decalines via TiCl4 promoted Michael-aldol and Baylis-Hillman reactions

The addition of 0.5 equiv of TiCl(4) to (cyclo)alkanones tethered to α,β-unsaturated ketones afforded polyfunctionalized diquinanes, hydrindanes, and decalines. These products, resulting from a Michael-aldol or a Baylis-Hillman reaction, can be obtained with high or total diastereoselectivity in moderate to high yields. These scaffolds represent interesting building blocks for the synthesis of complex natural products.     

Methane formation from CaCO3 reduction catalyzed by high pressure

Under high pressures of several giga-pascals using hydrothermal diamond anvil cell,methane generated directly from CaCO3 reduction in gold-lined chamber is in situ measured by Raman spectroscopy at the temperature of 550℃ Fhe reducing agents include FeO,SiO and natural fayalite（Fe2SiO4）,and the resource of hydrogen are water and natural serpentine（Mg3Si2O5（OH）4）. The study demonstrates the existence of abiogenic formation of methane under high pressures in the Earth＇s interior and that the application of high pressure to catalyze multicomponent reactions is a very promising method.