辛烷基酚聚氧乙烯醚反相微乳体系的相行为及纳米复合碳酸盐的制备

绘制了一系列辛烷基酚聚氧乙烯醚(OP-10)+正辛醇+环己烷+水(或CaCl₂水溶液)拟三元体系相图,分别研究了助表面活性剂正辛醇的添加比例和CaCl₂水溶液的浓度对微乳区域的影响,发现在OP-10+正辛醇+环己烷+水拟三元体系相图中,随着正辛醇/OP-10的质量比逐渐增大,微乳区的面积逐渐增大,当正辛醇/OP-10质量比为1:2.5时微乳区的面积最大,之后微乳区面积随着其质量比的增大而减小,表明适量地加入助表面活性剂正辛醇有利于微乳区的形成;但过多地增加正辛醇的量反而不利于微乳相的形成。 确定正辛醇/OP-10的质量比为1:2.5,改变CaCl₂的浓度,发现OP-10+正辛醇+环己烷+CaCl₂水溶液拟三元体系相图中,CaCl₂浓度为0.1 mol/L时微乳区面积最大。分别配制总浓度为0.1 mol/L的5种不同摩尔比的Ca²⁺/Ba²⁺微乳液,并与等摩尔的碳酸钠水溶液反应制备共沉淀碳酸盐,使用扫描电子显微镜(SEM)对所制备样品进行表征分析,发现当微乳液为钙离子盐时,主要形成大的立方形颗粒;掺入钡离子,Ca²⁺和Ba²⁺摩尔比为3:1、1:1和1:3时,形成的沉淀分别为四棱锥形、球形和玉米棒形;当微乳液为钡离子盐时,沉淀主要为不规则多面体。     

CTAB反相微乳体系的相行为研究

实验绘制了系列十六烷基三甲基溴化铵(CTAB)+正丁醇+正己烷+水(或CaCl2水溶液)拟三元体系相图。分别研究了正丁醇的添加比例和CaCl2水溶液的浓度对微乳区域的影响,发现随着正丁醇的相对比例逐渐增大,拟三元体系中微乳区的面积逐渐减小,表明过多增加正丁醇的量不利于微乳相的形成;发现总体上随着CaCl2水溶液摩尔浓度的增加,拟三元体系中微乳区的面积逐渐减小,表明强电解质的加入对微乳相影响较大,较高浓度的CaCl2会使部分CTAB失去表面活性而难以形成微乳液,导致微乳相区域逐渐减小。实验测定了电导率随水(或CaCl2水溶液)含量变化的规律,依据电解质理论探讨了微乳液的微观结构,并通过选择一定R0值的CaCl2微乳液与等摩尔的碳酸钠水溶液反应制备了球形纳米碳酸钙粒子。     

水溶性高聚物萃取分离光度法测定Ca2+的研究

利用在无机盐存在下,水溶性高聚物可分为两相的特点,研究了在聚乙二醇-邻苯二酚紫-邻二氮菲-硫酸铵体系中,Ca2+、Al3+、Co2+、Cu2+、Fe3+、Ni2+、Pb2+、Zn2+混合溶液中Ca2+的分离及测定条件,实现了Ca2+与Al3+、Co2+、Cu2+、Fe3+、Ni2+、Pb2+、Zn2+的定量分离和测定.Ca2+质量浓度在0.05～1.0 μg/mL范围内具有良好的线性关系,回收率92%～105%.     

不同金属反离子对含高效氯氟氰菊酯微乳液形成规律及其稳定性的研究

将十二烷基苯磺酸盐和苯乙烯化苯酚聚氧乙烯醚按摩尔比1∶1混合后, 结合5种金属反离子配成增溶高效氯氟氰菊酯的载药微乳体系, 研究其在导电机理、相行为及热贮稳定性上的差异. 结果表明, K+和Na+的十二烷基苯磺酸盐易于形成O/W型微乳液, Li+次之, Ca2+和Mg2+的十二烷基苯磺酸盐, 不利于形成O/W型微乳液.     

钙调素离子选择性的理论研究

通过分子动力学模拟计算研究了Ca2+, Mg2+, K+, Na+与钙调素形成复合物的结构和能量特征. 计算得到了结合不同离子后的钙调素结构差异, 阐明了钙调素对这几种离子具有不同结合性质的结构和动力学原因. 其中, Ca2+与钙调素EF-hand基序中侧链残基上的氧原子形成配位键, 从而使其复合物的结构有较大的改变, 而和Ca2+同一主族, 性质相似的Mg2+及不同主族的Na+和K+, 它们与钙调素的结合能力比Ca2+与钙调素的弱许多, 对钙调素结构的影响也较小, 由此推测钙调素与Ca2+的结合机制和钙调素对Ca2+具有选择性的原因是由离子与钙调素中EF-hand基序的结合强度和构型共同决定的.     

交联羧甲基红薯淀粉降低水中Ca~(2+)含量的研究

以环氧氯丙烷为交联剂,氯乙酸为羧甲基化试剂,合成交联羧甲基红薯淀粉并且研究其降低水中的Ca2+含量的效果.结果显示,交联羧甲基红薯淀粉吸附ca2+的适宜条件为,淀粉取代度0.721、2%淀粉用量、pH 8,吸附时间30min、吸附温度70℃下,交联羧甲基红薯淀粉对水中Ca2+的吸附量可达4.53mmol/L,Ca2+清除率为75.33%.交联羧甲基红薯淀粉吸附Ca2+的行为遵从Langmuir等温吸附方程.     

Ca2+交换的几种分子筛的氮氩分离性能

采用水溶液离子交换法制备了Ca2+交换的4A,13X和LSX分子筛,并在25 ℃下测定了它们的静态吸附等温线和动态穿透曲线.研究发现, Ca2+交换的4A,13X和LSX分子筛对氮的吸附性能都明显优于其相应的钠型分子筛,而它们对氩的吸附量变化不大,说明Ca2+交换的这三种分子筛是较好的氮氩分离吸附剂.从动态吸附的结果来看,所研究的各种分子筛都有一个最优的吸附分离压力,在本论文研究的压力范围内,这个最优压力在0.6 MPa附近.由穿透曲线可推算出混合气体的吸附量,通过氮和氩在混合气体中的吸附量和相应纯气体吸附量的对比可以得出,对于氮氩吸附选择性较高的分子筛,氮的存在对氩的吸附量有较大的影响.     

不同水煤浆分散剂与煤之间的相互作用规律研究Ⅴ.煤在分散剂水溶液中的溶出离子及其对CWS性质的影响

通过原子吸收和等离子体原子发射光谱法,研究了6种不同分散剂对14种煤溶出Ca2+、Mg2+、Fe3+(Fe2+)、Al3+、SiO2-3离子的影响.结果表明,煤中溶出高价离子的数量,主要取决于分散剂与高价离子间的相互作用特征,以及矿物质的种类和数量.煤在不同分散剂水溶液中溶出高价离子的多少,并不单纯与水煤浆(CWS)的流变性或煤的成浆性具有相关性.煤中矿物质对CWS性质的影响,是多种因素综合作用的结果,溶出离子的种类和数量只是其中的重要因素之一.     

Ca2+离子对PLA2结构和功能的影响

从旅顺产白眉蝮蛇(Glyodius blomhoffi Brevicaudaus,GBB)蛇毒(GBBSV)中首次纯化得到了电泳纯和质谱纯磷脂酶A2(GBB-PLA2). 采用电泳、质谱、等离子体发射光谱、紫外、荧光光谱测试技术对GBB-PLA2进行了系统表征. HPLC-ESI-MS法测得的精确分子量为13 965.07 amu,HPLC-ESI-MS/MS法鉴定GBB-PLA2为江浙蝮蛇和尖吻蝮蛇蛇毒PLA2的同源性蛋白,分别得到4个和1个同源性肽段. 凝胶过滤、质谱和SDS-PAGE测试技术结果表明,GBB-PLA2以稳定的单体形式存在. 电感耦合等离子体发射光谱分析法(ICP-AES)测得每1个磷脂酶A2含有1个Ca2+离子,Ca2+是PLA2活性所必需的. Ca2+的除去使PLA2活性降低90%,外加Ca2+明显加速PLA2水解底物DPPC的速度. Ca2+起稳定PLA2结构的作用,可使GBB-PLA2的热变性温度提高3 ℃.     

钴胺素溶析结晶过程及离子杂质对其晶体生长的影响

采用激光法研究了钴胺素的结晶过程热力学,考察了温度、溶剂对溶解度和超溶解度的影响,并测定了介稳区,介稳区的宽度随体系中丙酮含量的减小而变宽. 研究了离子杂质Na+、Mg2+、Ca2+和Fe3+对钴胺素结晶诱导期的影响. 结果表明,离子的存在使得晶体更容易出现断裂和聚结,并用扫描电子显微镜测试技术对晶体的表面形貌进行了表征. 结果表明,Fe3+、Mg2+比Na+、Ca2+影响更明显.     

Rapid Evaluation of Water-in-Oil (w/o) Emulsion Stability by Turbidity Ratio Measurements

In this Note, we investigated the turbidity ratio method for the evaluation of water-in-oil emulsion stability. The slope of turbidity ratio of water-in-oil emulsions with time was taken as an index of stability; the higher the slope, the less stable the system. Various factors affecting the stability of emulsion such as HLB of emulsifier, amount of emulsifiers, and water were tested using this technique. The results of the turbidity ratio technique for the evaluation of emulsion stability were well consistent with those obtained by the measurement of phase separation when incubated for 30 days at room temperature. Copyright 2000 Academic Press.     

水性环氧复合乳化剂的合成及性能

以环氧树脂E-44、2-氨基-5-磺酸基苯甲酸、乙二醇丁醚和正丁醇为原料,合成一种新型阴离子环氧乳化剂EP-D;同时,E-44和聚乙二醇(PEG6000)以摩尔比2∶1反应,合成端环氧基非离子环氧乳化剂EP-PEG;将EP-D与EP-PEG按不同质量比复配获得不同配比的EP-D/EP-PEG水性环氧复合乳化剂。 分别研究了EP-D/EP-PEG及EP-PEG在环氧树脂中加入质量分数为6%~12%时的乳化性能及形成乳液的表面张力、电导率和胶粒的Zeta电位、粒径。 结果表明,当EP-D和EP-PEG以质量比3∶5复配,总加入质量分数为9%时,制备的环氧乳液性能最佳。 与EP-PEG形成的环氧乳液相比,复配环氧乳化剂用量少,乳液铺展性好、稳定性高,且乳液在相反转时的固含量提高了10%以上。 复配环氧树脂乳液中胶粒的Zeta电位为-41.9 mV、粒径为342 nm、表面张力为25.5 mN/m、粘度为14 mPa·s。 这表明利用乳化剂EP-D与EP-PEG复配新合成的EP-D/EP-PEG水性环氧复合乳化剂可制备稳定性好,固含量高的乳液。     

纳米玉米醇溶蛋白微球稳定的O/W型Pickering乳液

利用相分离工艺制备玉米醇溶蛋白(zein)纳米微球,微球粒径可控制在40 nm左右;经旋转蒸发制得zein溶胶体系,zein溶胶具有明显的丁达尔现象,静置数月不聚沉,Zeta电位法测得zein微球在pH值为4.0时分散性能最佳。 以纳米zein微球为固相稳定剂制备O/W型Pickering乳液,考察了zein胶体加入量、油水体积比等因素对乳液稳定性的影响。 实验结果表明,zein胶体加入量的质量分数控制为0.4%,高油水体积比将有利于Pickering乳液的长时间稳定。 基于zein分子的两亲结构和界面组装特点,提出了zein微球稳定Pickering乳液的作用机制。     

Stability and phase behavior of acrylamide-based emulsions before and after polymerization

The stability and phase behavior of acrylamide-based emulsions, prepared with surfactants consisting of lipophilic Span80 and hydrophilic OP10, before or after polymerization were investigated. The research results indicated that the phase separation behavior of the W/O-type emulsions is related to the toluene/water ratio. When the water volume fraction was larger, the phase separation mechanism was mainly a penetration of aqueous molecules from the dispersed-phase droplets. When the water volume fraction was smaller, the phase separation mechanism was mainly a sedimentation of the separated aqueous droplets. At a fixed toluene/water ratio, the emulsion stability and the emulsion type are related not only to the ratio of the two surfactants but also to the acrylamide concentration, and the effect of increasing acrylamide concentration on the character of the emulsions is similar to that of increasing OP10 mass fraction (increasing HLB value), which determines the corresponding relationship between acrylamide concentration and HLB value in the most stable emulsion system. To obtain the most stable emulsion at a fixed acrylamide concentration, the emulsion with higher acrylamide concentration needs a lower HLB value for the emulsion systems.     

Formulation development of a filter-sterilizable lipid emulsion for lipophilic KW-3902, a newly synthesized adenosine A1-receptor antagonist

KW-3902 (a newly synthesized adenosine A1-receptor antagonist) has potent diuretic and renal protective activities. The objective of the present study was to develop an injectable formulation of KW-3902, that was water-insoluble and less than 1 microg/ml, and so lipid emulsion was selected as a favorable formulation. Changing the mixing ratio of oil to lecithin, the particle size of the lipid emulsion was controlled, and by adjusting the mixing ratio of oil/lecithin=1:1, the weight ratio, a lipid emulsion with a mean particle size of 130 nm was prepared. This small particle size makes this emulsion filter-sterilizable, which is a favorable feature for heat labile products. The stability of the KW-3902 lipid emulsion was assessed from the viewpoint of the electrostatic repulsion, and by including the oleic acid a stable lipid emulsion was developed, which was stable for at least 12 months at 10 and 25 degrees C and for 3 months at 40 degrees C. The feature of this small particle size emulsion was also characterized by comparing it with a conventional emulsion (oil/lecithin=1:0.12, the weight ratio, particle size is 220 nm). The release of KW-3902 from the oil particles was measured and the apparent permeability of KW-3902 was calculated from the equation according to Fick's theory. The apparent permeability, P, of KW-3902 was not affected by the particle size of the emulsion (1.78x10(-11) cm/s for the small emulsion and 1.76x10(-11)cm/s for the conventional emulsion). The distribution mode of KW-3902 in the lipid emulsion was also discussed by considering the findings of the permeability and solubility of KW-3902.     

Preparation,characterization, and properties of polyamic acid nano‐emulsion

A facile method was developed to prepare polyamic acid (PAA) nano‐emulsion using a non‐aqueous emulsification. The resultant PAA nano‐emulsion was characterized by light‐scattering particle size analysis, transmission electron microscopy (TEM), zeta potential, and conductivity analyses. It was found that polyamic acid salt (PAS), formed by partially neutralizing PAA at the carboxylic groups using triethyl amine (TEA), was of great importance for nano‐emulsification. The effect factors on the formation of PAA nano‐emulsion were investigated. To get a stable PAA nano‐emulsion in methanol (precipitant), the following ratios are required: amine/COOH (molar ratio) = 0.6–0.7, precipitant/solvent (mass ratio) = 1.5–2.25. A PAA nano‐emulsion with droplets ranging in size from 50 to 100 nm was obtained under optimized conditions. The driving force for the formation of PAA nano‐emulsion was also discussed. Copyright © 2011 John Wiley & Sons, Ltd.     

Effect of Molecular Weight of WPU on the Heterogenic PUA Composite Latex Prepared by Soap-Free Emulsion Polymerization

Aqueous acrylic-polyurethane (PUA) composite emulsion was prepared by soap-free seeded emulsion copolymerization. Waterborne polyurethane (WPU) was used as the seeded emulsion and functioned as surfactant. The effect of molecular weight of WPU on the heterogenic was investigated. The molecular weight of WPU was controlled by varying the NCO/OH mole ratio. The GPC results confirmed that the molecular weight of WPU presented double distribution. And the molecular weight of WPU decreased with the increasing NCO/OH mole ratio. Surface tension test indicated that the molecular weight had little influence on the surface activity of WPU. However, after emulsion copolymerization of acrylic monomers, the morphology and properties of the PUA composite were impacted markedly by the molecular weight of WPU. With an increase in the NCO/OH mole ratio, the morphology of PUA composite latex changed from core-shell structures to fish bowl structure, and the mechanical properties of PUA films changed correspondingly.     

荧光探针法研究乳化剂对硅/丙核壳乳液聚合行为的影响

用荧光探针(芘)法测定了十二烷基硫酸钠(SDS)、烷基酚聚氧乙烯醚(OP-10),以及复配乳化剂的临界胶束浓度(CMC),并首次把荧光探针技术应用到硅/丙核壳乳液聚合反应的研究中.利用芘的I₁/I₃值,结合胶束微环境的极性变化规律和乳液聚合机理,探讨了乳化剂对聚合反应的影响.结果表明,荧光探针(芘)法可用于研究硅/丙乳液的聚合行为和确定乳化剂配比.通过粒径分析、透射电镜(TEM)对产品的结构进行了表征.     

聚丙烯酸增稠剂的反相乳液聚合及其增稠性能

采用具有增稠和抗电解质作用的丙烯酸聚氧乙烯酯活性单体和具有聚合稳定作用的高分子表面活性剂,通过反相乳液聚合法合成了涂料印花用丙烯酸系增稠剂.研究了活性单体、交联剂、反应时间等因素对产物性能的影响.得出活性单体用量占共聚单体摩尔数的0.5%,交联剂占共聚单体质量的0.3%,反应时间为1.5h时,增稠剂的综合效果最好.     

Physicochemical properties of structured phosphatidylcholine in drug carrier lipid emulsions for drug delivery systems

Drug carrier emulsions were prepared with structured phosphatidylcholine (PC-LM) which has both a long hydrocarbon chain and a medium hydrocarbon chain, and the characteristics of PC-LM as an emulsifier were investigated by measuring the creaming ratio, the surface tension of the emulsion system, and the mean particle size and zeta potential of the oil droplets in emulsions. The emulsion prepared with PC-LM as an emulsifier kept the condition and the ratio of separation was lower than those with purified egg yolk lecithin (PEL). The mean particle size of the emulsion prepared with PC-LM was smaller than that with PEL when using only sonication, approximately 250 nm. When using a high-pressure homogenizer after sonication, the mean emulsion size with PC-LM was also smaller than with PEL, approximately 150 nm. The surface tension of the various emulsions and the zeta potential of the emulsion droplets were measured to investigate the stability of the systems. In emulsions with PC-LM or PEL, the surface tension as an index of stability increased as the pressure of the homogenizer increased. Moreover, the zeta potential of the emulsion droplets prepared with PC-LM also increased with an increase in pressure of the homogenizer. As a result, it was found that the drug carrier emulsion prepared with PC-LM had significant advantages in terms of stability and mean diameter. We considered it could be used for the preparations of nanoparticle dispersion systems in drug delivery systems.