Trace Determination of Chromium by Square‐Wave Adsorptive Stripping Voltammetry on Bismuth Film Electrodes

This works reports the use of adsorptive stripping voltammetry (AdSV) for the trace determination of chromium on a rotating‐disk bismuth‐film electrode (BFE). During the reductive accumulation step, all the chromium species in the sample were reduced to Cr(III) which was complexed with cupferron and the complex was accumulated by adsorption on the surface of a preplated BFE. The stripping step was carried out by using a square‐wave (SW) potential‐time voltammetric signal. Electrochemical cleaning of the bismuth film was employed, enabling the same bismuth film to be used for a series of measurements in the presence of dissolved oxygen. The experimental variables as well as potential interferences were investigated and the figures of merit of the method were established. Using the selected conditions, the 3σ limit of detection for chromium was 100 ng L^?1 (for 120 s of preconcentration) and the relative standard deviation was 3.6% at the 2 μg L^?1 level (n=8). Finally, the method was applied to the determination of chromium in real samples with satisfactory results.     

Novel Sensitive Voltammetric Detection of Trace Gallium(III) with Presence of Catechol Using Mercury Film Silver Based Electrode

A new adsorptive stripping voltammetric method for the determination of trace gallium(III) based on the adsorption of gallium(III)‐catechol complex on the cyclic renewable mercury film silver based electrode (Hg(Ag)FE) is presented. The effects of various factors such as: preconcentration potential and time, pulse height, step potential and supporting electrolyte composition are optimized. The calibration graph is linear from 2 nM (0.14 μg L^?1) to 100 nM (6.97 μg L^?1) for a preconcentration time of 30 s, with correlation coefficient of 0.9993. For a Hg(Ag)FE with a surface area of 9.7 mm² the detection limit for a preconcentration time of 90 s is as low as 7 ng L^?1. The repeatability of the method at a concentration level of the analyte as low as 0.05 μg L^?1, expressed as RSD is 3.6% (n=5). The proposed method was successfully applied by studying the natural samples and simultaneous recovery of Ga(III) from spiked water and sediment samples.     

Sensitive Anodic Stripping Voltammetric Copper Ions Determination Performed in Double Deposition and Double Stripping Steps System for Real Water Samples Analysis

The article reports on utilization of double deposition and stripping steps for increasing sensitivity of Cu(II) determination by anodic stripping voltammetry (ASV) at two lead film working electrodes. A significant preconcentration of copper was achieved thanks to utilization of a simple design of four electrodes system that gives possibility to perform one measurement cycle consisting of two deposition and two stripping steps. Due to the fact that deposition step is doubled, the concentration of Pb(II) needed to lead film electrodes formation was significantly reduced as compared to traditional procedures using three electrodes system. The analytical procedure of Cu(II) determination was optimized. The experimental factors: supporting electrolyte's pH and its concentration, lead ions concentration, potential and time of deposition at both working electrodes were studied. The Cu(II) peak current was linearly dependent on its concentration from 5×10^?10 to 2×10^?8 mol L^?1 (deposition time of 270 and 160 s at the first and the second working electrode, respectively). The obtained detection limit for copper ions determination was 2.1×10^?10 mol L^?1. The described procedure was validated by analysis of two water certified reference materials. The described procedure was also utilized for real water sample analysis.     

Sequential Voltammetric Determination of Uranium,Cadmium and Lead by Using the ex situ Bismuth Film Electrode: Application to Phosphate Fertilizers

A sequential voltammetric procedure for the determination of uranium, cadmium and lead was investigated at an ex situ bismuth film electrode (BiFE). First, the adsorptive stripping voltammetry was applied to assay the U(VI)‐cupferron complex in the differential pulse mode (detection limit of 1.0 µg L^?1, 200 s accumulation time). Through the manipulation of the same aliquot of the sample, efforts were made to quantify cadmium and lead by square wave anodic stripping voltammetry. Detection limits of 2.03 µg L^?1 for Cd (II) and 2.43 µg L^?1 for Pb (II) were calculated (100 s accumulation time). The methodology was successfully applied to phosphate fertilizer samples after open vessel wet decomposition (HNO₃/H₂O₂). The following value ranges were evaluated: U (VI) 37.2–150 mg kg^?1, Pb (II) 78.3–204 mg kg^?1 and Cd (II) 44.1–71.6 mg kg^?1. Validation was performed by using the standard reference materials SRM‐695 – phosphate fertilizer – and SRM‐1643e – water.     

Sensitive adsorptive stripping voltammetric method for direct determination of trace concentration of lead in the presence of cupferron in natural water samples

This paper reports the use of an adsorptive voltammetric technique for Pb(II) determination using cupferron as a selective complexing agent. After accumulation of the complex onto a hanging mercury drop electrode, the electrode potential was scanned with differential pulse modulation and the reduction current of lead was observed at about??0.5?V. Under optimum conditions (5?×?10^?4?mol?L^?1 cupferron concentration, 0.1?mol?L^?1 acetate buffer (pH 5.5), adsorption at??50?mV for 30?s) the detection limit was 5.1?×?10^?10?mol?L^?1. The relative standard deviation of five measurements for low lead concentration was 3.1%. The accuracy of the method was tested by analysing certified reference material (SPS-WW1 Waste Water). Finally, the method was successfully applied to the determination of Pb(II) in river water samples without any pretreatments.     

Lead Film Electrode Prepared with the Use of a Reversibly Deposited Mediator Metal in Adsorptive Stripping Voltammetry of Nickel

The paper presents the first report on application of a “hybrid” lead film electrode for the adsorptive stripping voltammetric determination of Ni(II) in the presence of nioxime as a complexing agent. The strategy to create a “hybrid” electrode is based on the combination of ex situ and in situ plating methods and the use of a reversibly deposited mediator metal (Zn) for the lead film formation. The surface morphology of a new sensor was characterized by atomic force microscopy. The detection limit for Ni(II) obtained at 120 s of accumulation time was 3.9×10^?11 mol L^?1. The proposed method was validated for the determination of nickel in water certified reference materials with good results.     

Catalytic Adsorptive Stripping Voltammetry of Cobalt in the Presence of Nitrite at an In Situ Plated Bismuth Film Electrode

For the first time an in situ plated bismuth film electrode has been applied to catalytic adsorptive stripping voltammetry of cobalt in the presence of nitrite. At optimised conditions bismuth film was plated before each measurement for 30 s at ?1.0 V from a sample solution with the added supporting electrolyte and Bi(III) in the form of its complex with tartrate. The calibration graph for Co(II) for an accumulation time of 120 s was linear from 5×10^?10 to 1×10^?8 mol L^?1. The detection limit was 1.1×10^?10 mol L^?1. The proposed procedure was applied for Co(II) determination in certified water reference material.     

Adsorptive Stripping Voltammetric Determination of Trace Uranium with a Bismuth‐Film Electrode Based on the U(VI)→U(V) Reduction Step of the Uranium‐Cupferron Complex

This work reports the use of adsorptive stripping voltammetry (AdSV) for the determination of uranium on a preplated rotating‐disk bismuth‐film electrode (BiFE). The principle of the method relied on the complexation of U(VI) ions with cupferron and the subsequent adsorptive accumulation of the complex on the surface of the BiFE. The uranium in the accumulated complex was then reduced by means of a cathodic voltammetric scan while the analytically useful U(VI)→U(V) reduction signal was monitored. The experimental variables as well as potential interferences were investigated and the figures of merit of the method were established. Using the selected conditions, the 3σ limit of detection for uranium was 0.1 μg L^?1 at a preconcentration time of 480 s and the relative standard deviation was 4.7% at the 5 μg L^?1 level for a preconcentration time of 120 s (n=8). The accuracy of the method was established by analyzing a reference sea water sample.     

Fast Simultaneous Adsorptive Stripping Voltammetric Determination of Ni(II) and Co(II) at Lead Film Electrode Plated on Gold Substrate

A fast adsorptive stripping voltammetric procedure for simultaneous determination of Ni(II) and Co(II) in the presence of nioxime as a complexing agent at an in situ plated lead film electrode was described. The time of determination of these ions was shortened due to the application of gold as a substrate for lead film. At gold substrate lead film formation and accumulation of Ni(II) and Co(II) complexes with nioxime proceeds simultaneously. To obtain a stable signals for both ions a simple procedure of activation of the electrode was proposed. Calibration graphs for an accumulation time of 20 s were linear from 5×10^?9 to 1×10^?7 mol L^?1 and from 5×10^?10 to 1×10^?8 mol L^?1 for Ni(II) and Co(II), respectively. The procedure with the application of a lead film electrode on a gold substrate was validated in the course of Ni(II) and Co(II) determination in certified reference materials.     

New Protocol for Determination of Rifampicine by Adsorptive Stripping Voltammetry

For determinations of organic compounds by adsorptive stripping voltammetry till now the same material of the electrode has been used for the accumulation and stripping steps. This paper describes a new protocol for extending the range of organic compounds, which can be determined by adsorptive stripping voltammetry. In the proposed procedure the accumulation step was performed on the electrode modified by a lead film, which assures adsorption of the studied species on the modified electrode and then the stripping step of the accumulated substance was performed on the support of the lead film electrode. As an example rifampicine was accumulated by adsorption at the lead film electrode while in the stripping step lead film and then the accumulated rifampicine were oxidized at a glassy carbon electrode. Using an acetate buffer as a supporting electrolyte a calibration graph for rifampicine in the range from 2.5×10^?10 to 1×10^?8 mol L^?1 was obtained. The detection limit for rifampicine following 60 s accumulation time was equal to 9×10^?11 mol L^?1. The obtained detection limit was comparable or lower than reported previously for other stripping voltammetric procedures. The proposed procedure was applied to rifampicine determination in pharmaceutical preparation.     

Sensitive voltammetric determination of gallium in aluminium materials using renewable mercury film silver based electrode

Simple cyclic renewable silver amalgam film electrode (Hg(Ag)FE), applied for the determination of gallium(III) using differential pulse anodic stripping voltammetry (DP ASV), is presented. The effects of various factors such as: preconcentration potential and time, pulse height, step potential and supporting electrolyte composition are optimised. The calibration graph is linear from 5?nM (0.35?µg?L^?1) to 80?nM (5.6?µg?L^?1) for a preconcentration time of 60?s, with correlation coefficient of 0.995. For a Hg(Ag)FE with a surface area of 9.9?mm² the detection limit for a preconcentration time of 120?s is as low as 0.1?µg?L^?1. The repeatability of the method at a concentration level of the analyte as low as 3.5?µg?L^?1, expressed as RSD is 3.2% (n?=?5). The proposed method was successfully applied by studying the synthetic samples and simultaneously recovery of Ga(III) from spiked aluminium samples.     

Catalytic Adsorptive Stripping Voltammetry of Cobalt in the Presence of Dimethylglyoxime and Nitrite at In Situ Plated Lead–Copper Film Electrode

A lead‐copper film electrode was proposed for Co(II) determination by catalytic adsorptive stripping voltammetry. The electrode was plated in situ and hence the exchange of a solution after plating step was not required. At optimized conditions the calibration graph for Co(II) was linear from 5×10^?10 to 2×10^?8 mol L^?1 for accumulation time of 15 s. The relative standard deviation for Co(II) determination at concentration 5×10^?9 mol L^?1 was 4.1%. The detection limits for Co(II) were 1.2×10^?10 and 1.0×10^?11 mol L^?1 for an accumulation time of 15 and 180 s, respectively. The method was applied to Co(II) determination in certified reference material and other water samples.     

Determination of Folic Acid by Adsorptive Stripping Voltammetry at a Lead Film Electrode

An adsorptive stripping voltammetric procedure for the determination of folic acid at an in situ plated lead film electrode was described. Formation of lead film on a glassy carbon substrate and accumulation of folic acid was performed simultaneously from an acetate buffer solution of pH 5.6 at the potential ?0.88 V. The measurements were carried out from aerated solutions. The calibration graph for an accumulation time of 300 s was linear from 2×10^?9 to 5×10^?8 mol L^?1. The detection limit was 7×10^?10 mol L^?1, the relative standard deviation for 2×10^?8 mol L^?1 of folic acid was 3.9%. The proposed procedure was applied to folic acid determinations in pharmaceutical preparations.     

Adsorptive Stripping Determination of Scandium(III) with Mordant Blue 9 on Silver Amalgam Film Electrode

A new adsorptive stripping voltammetric method for the determination of trace scandium(III) based on the adsorption of scandium(III)‐mordant blue 9 complex on the cyclic renewable mercury film silver based electrode (Hg(Ag)FE) is presented. The effects of various factors such as: preconcentration potential and time, pulse height, step potential and supporting electrolyte composition are optimized. The calibration graph is linear from 2 nM (0.09 μg L^?1) to 90 nM (4 μg L^?1) for a preconcentration time of 45 s, with correlation coefficient of 0.9995. For a Hg(Ag)FE with a surface area of 7.9 mm² the detection limit for a preconcentration time of 90 s is as low as 5 ng L^?1. The repeatability of the method at a concentration level of the analyte as low as 0.2 μg L^?1, expressed as RSD is 1.9 % (n=5). The proposed method was successfully applied and validated by studying the certified reference material (CRM 320 – river sediment) and natural samples with simultaneous recovery of Sc(III) from spiked water and sediment samples.     

Preconcentration,Determination and Speciation of Chromium(III) Using Solid Phase Extraction and Flame Atomic Absorption Spectrometry

A facile, reliable and reproducible method for speciation and determination of the traces amounts of chromium(III) in waste water has been developed. The method was based on complex formation on the surface of the ENVI‐18 DSK^? disks followed by stripping of the retained species by minimum amounts of appropriate organic solvents. The elution was efficient and quantitative. The effects of potential interfering ions, pH, ligand amount, stripping solvent, and sample flow rate were also investigated. Under the optimal experimental conditions, the break‐through volume was found to be about 1500 mL providing a preconcentration factor of 300. The maximum capacity of the disks was found to be 225 ± 3.9 μg for Cr³⁺. A limit of detection of 0.02 ng.mL ^?1 was obtained, and the method was applied for determination of chromium in electroplating industries waste water located in the eastern regions of Tehran.     

How to Determine Uranium Faster and Cheaper by Adsorptive Stripping Voltammetry in Water Samples Containing Surface Active Compounds

A modification of the voltammetric procedure for the determination of uranium in the presence of cupferron using hanging mercury drop electrode is presented. The pulsed potential accumulation was proposed for the minimization of interferences of surface active substances. The calibration plot for U(VI) in the presence of 2 ppm Tritonu X‐100 was linear from 1.7×10^?10 to 2.0×10^?8 mol L^?1 for an accumulation time of 60 s, with correlation coefficient of 0.996. The application of this method was tested in the determination of uranium in certified reference material NASS‐5 and river water samples.     

Square wave anodic stripping voltammetric determination of lead(II) using a glassy carbon electrode modified with a lead ionophore and multiwalled carbon nanotubes

We report on a glassy carbon electrode (GCE) modified with a lead ionophore and multiwalled carbon nanotubes. It can be applied to square wave anodic stripping voltammetric determination of Pb(II) ion after preconcentration of Pb(II) at ?1.0?V (vs. SCE) for 300?s in pH?4.5 acetate buffer containing 400?μg?L^?1 of Bi(III). The ionophore-MWCNTs film on the GCE possesses strong and highly selective affinity for Pb(II) as confirmed by quartz crystal microbalance experiments. Under the optimum conditions, a linear response was observed for Pb(II) ion in the range from 0.3 to 50?μg?L^?1. The limit of detection (at S/N?=?3) is 0.1?μg?L^?1. The method was applied to the determination of Pb(II) in water samples with acceptable recovery.

Ultra‐sensitive Voltammetric Aluminum Determination on a Solid Bismuth Electrode for Water Filter Verification

This work presents a new ultra‐sensitive method of Al(III) as Al‐cupferron complex voltammetric determination, in 0.04 M ammonium sulfate of pH=6.1 and 0.003 M cupferron by environmentally friendly and durable Bismuth Bulk Annular Band Electrode (BiABE). The optimal measuring parameters include: potential window from ?700 to ?1250 mV versus Ag|AgCl, preconcentration time and potential of 120 s, ?700 mV, respectively. The electrode surface can be activated by fast in situ method: applying short conditioning by the potential of ?1300 mV. The best obtained analytical parameters are: range of linearity 0.2–1.2 μg L^?1 with high sensitivity of 1.333 μA/μg L^?1, limit of detection 0.04 μg L^?1 and repeatability below 2.3 %. The described procedure was verified using various CRMs, i. e. surface waters, waste waters and tea leaves. Satisfactory recovery values were obtained in the interval 99.2–103.5 %. Developed DPV procedure was used to determine Al in tap and natural waters in aspect of recovery of aluminum, which was added to the samples. For the first time, we tested also Al removal efficiency from water by the water filters mounted in the trip bottle.     

Determination of uranium by adsorptive stripping voltammetry at a lead film electrode

An adsorptive stripping voltammetric procedure for the determination of U(VI) at an in situ plated lead film electrode is described. The U(VI) complex with cupferron was accumulated from an acetate buffer solution of pH 4.2 at the potential −0.65 V. The measurements were carried out from undeaerated solutions. The calibration graph for an accumulation time of 180 s was linear from 5 × 10⁻¹⁰ to 2 × 10⁻⁸ mol L⁻¹. The detection limit was 2 × 10⁻¹⁰ mol L⁻¹, the relative standard deviation for 2 × 10⁻⁸ mol L⁻¹ U(VI) was 4.3%. The proposed procedure was validated in the course of U(VI) determination in water certified reference materials.     

Stripping Potentiometry of Lead,Cadmium and Copper at a Nafion Coated Glassy Carbon Electrode with Encapsulated Mercury Acetate

Abstract

The stripping potentiometric determination of lead, cadmium and copper with mercury film glassy-carbon electrodes coated with a Nafion membrane was investigated. The mercury film was plated using either mercury(II) acetate encapsulated within the Nafion membrane or a mercury(II) solution. Dissolved dioxygen was used as the stripping agent. The electrodes showed promising properties, particularly robustness and response repeatability. A linear dependence of the stripping time on concentration was found in the μg l^?1 concentration range (s.d. of intercept ≤ 0.3 μg l^?1, r.s.d. of slope ≤ 1%, for both lead and cadmium).