A 2‐D‐HPLC‐CE platform coupled to ESI‐TOF‐MS to characterize the phenolic fraction in olive oil

A 2‐D‐HPLC/CE method was developed to separate and characterize more in depth the phenolic fraction of olive oil samples. The method involves the use of semi‐preparative HPLC (C18 column 250×10 mm, 5 μm) as a first dimension of separation to isolate phenolic fractions from commercial extra‐virgin olive oils and CE coupled to TOF‐MS (CE‐TOF‐MS) as a second dimension, to analyze the composition of the isolated fractions. Using this method, a large number of compounds were tentatively identified, some of them by first time, based on the information concerning high mass accuracy and the isotopic pattern provided by TOF‐MS analyzer together with the chemical knowledge and the behavior of the compounds in HPLC and CE. From these results it can be concluded that 2‐D‐HPLC‐CE‐MS provides enough resolving power to separate hundreds of compounds from highly complex samples, such as olive oil. Furthermore, in this paper, the isolated phenolic fractions have been used for two specific applications: quantification of some components of extra‐virgin olive oil samples in terms of pure fractions, and in vitro studies of its anti‐carcinogenic capacity.     

Better understanding of carbon nanoparticles via high‐performance liquid chromatography‐fluorescence detection and mass spectrometry

RP‐HPLC coupled with fluorescence detection for separation of carbon nanoparticles (CNP) synthesized with microwave‐assisted pyrolysis of citric acid and 1,2‐ethylenediamine is presented. The influence of methanol content and pH of mobile phase on the separation of CNP has been investigated. Under optimal mobile phase and elution gradient conditions, the effect of mole ratio of amine to carboxylic groups (NH₂/COOH) in the initial reagents on CNP product is studied. At NH₂/COOH = 0.67, the strongest fluorescence CNP sample is obtained. The separated CNP fractions are collected and further characterized by UV‐visible absorption and photoluminescence (PL) spectroscopy, CE, transmission electron microscopy (TEM), and MALDI‐TOF MS. The absorption and PL emission bands of the fractions are bathochromatically shifted with the elution order of CNP on RP‐HPLC. The TEM images prove that CNP are eluted from the smallest to the largest. The MS data show that CNP undergo fragmentations, closely relating to their surface‐attached carboxylic acid and amide/amine moieties. This work highlights the merit of RP‐HPLC coupled with fluorescence detection, TEM, and MS for isolation and characterization of individual CNP species present in a CNP sample.     

Screening active anti‐breast cancer compounds from Cortex Magnolia officinalis by 2D LC–MS

Most of the anti‐breast cancer drugs are often limited owing to drug resistance and serious adverse reactions. Therefore, development of more targeted and low toxic drugs from traditional Chinese medicines for breast cancer are needed. At the same time, establishment of fast and effective drug screening methods are urgently required. We describe here a 2D LC method of MDA‐MB‐231 cell membrane chromatography combined with HPLC/MS for recognition, separation, and identification of target components from traditional Chinese medicine Cortex Magnolia officinalis. The MDA‐MB‐231 cells membrane was used to prepare the chromatographic stationary phase in the first dimension. The active compounds had a retention characteristic on the cell membrane chromatography model (10 × 2.0 mm, 5 μm). The retention fractions were enriched using an online C₁₈ column (10 × 1.0 mm, 5 μm) and were analyzed by the second dimension RP chromatography. Finally, the activity of the retention fractions was tested through in vitro experiments. Results showed that the retention fractions were honokiol and magnolol and the inhibition rate on MDA‐MB‐231 cell growth were 23 and 64 μM, respectively. These results support the conclusion that this coupled analytical technique could be an efficient method in drug discovery.     

Chromatographic characterization of high‐boiling petroleum fractions

Detailed investigation of solvent‐separated fractions of petroleum vacuum residues is necessary for understanding the separation mechanism using different solvents and to prepare better feedstocks for secondary conversion processes. The efficiency of different solvents to remove polars and insolubles from vacuum residues (of two Indian crude oils) has been studied. The solvents used were n‐heptane, n‐hexane, and n‐pentane (non‐polar) and ethyl acetate (polar). Soluble fractions were characterized for hydrocarbon group type analysis using high performance liquid chromatography (HPLC), average molecular weights using size exclusion chromatography (SEC), and boiling point distribution using high temperature gas chromatography (HTGC). Method development for HPLC analysis involved the study of parameters such as columns, solvent polarity, detectors, model compounds study, calibration, flow, and solvent gradient programming. The study demonstrated that ultimate soluble fractions have the least content of polar structures of the kind which can cause problems, during cracking and are least prone to cracking. The HPLC, SEC, and simulated distillation (SIMDIS) methods developed and standardized are simple, accurate, and suitable for the rapid assay needed for quick compositional surveys.     

Development of a fast liquid chromatography/mass spectrometry screening method for angiotensin‐converting enzyme (ACE) inhibitors in complex natural mixtures like snake venom

A new robust high‐performance liquid chromatography/electrospray ionization mass spectrometry (HPLC/ESI‐MS)‐based screening method for angiotensin‐converting enzyme (ACE)‐inhibiting substances in crude samples is described. The ACE assay is carried out in a typical offline setup by incubation of the samples with ACE and angiotensin I (AI), followed by stopping the reaction with acetonitrile containing val⁵‐AI serving as internal standard (I.S.). AI and the product angiotensin II (AII) are extracted from the incubation mixture by turbulent‐flow chromatography (TFC) applied in backflush mode as online solid‐phase extraction and are directly quantified by ESI(+)‐MS. The presence of ACE inhibitors (ACEi) is detected by an increase in AI signal intensity and a corresponding decrease of AII signal, as compared to the blank assay. The overall time of analysis of the TFC/ESI‐MS method was 5 min, thus making the described setup suitable for a rapid screening method. The assay was validated using a known ACE inhibitor and the IC₅₀ values found were in good accordance with a common HPLC/UV method and literature data. The method was successfully applied for the screening of size‐exclusion chromatography fractions of the venom of the pitviper Bothrops moojeni. Three of 18 analyzed fractions inhibited ACE, due to peptides present as components of this snake venom. These compounds were extracted from the two most‐active fractions by means of TFC and isolated by means of HPLC. Three peptides with ACE inhibitory activity were characterized and their structures were elucidated with ESI‐MS/MS‐based de novo sequencing to be ZKWPPGKVPP, ZKWPRPGPEIPP and ZNWPRPGPEIPP, respectively (Z = pyroglutamic acid). Copyright © 2010 John Wiley & Sons, Ltd.     

Analysis of pharmaceutical impurities using multi‐heartcutting 2D LC coupled with UV‐charged aerosol MS detection

To overcome challenges in HPLC impurity analysis of pharmaceuticals, we developed an automated online multi‐heartcutting 2D HPLC system with hyphenated UV‐charged aerosol MS detection. The first dimension has a primary column and the second dimension has six orthogonal columns to enhance flexibility and selectivity. The two dimensions were interfaced by a pair of switching valves equipped with six trapping loops that allow multi‐heartcutting of peaks of interest in the first dimension and also allow “peak parking.” The hyphenated UV‐charged aerosol MS detection provides comprehensive detection for compounds with and without UV chromophores, organics, and inorganics. It also provides structural information for impurity identification. A hidden degradation product that co‐eluted with the drug main peak was revealed by RP × RP separation and thus enabled the stability‐indicating method development. A poorly retained polar component with no UV chromophores was analyzed by RP × hydrophilic interaction liquid chromatography separation with charged aerosol detection. Furthermore, using this system, the structures of low‐level impurities separated by a method using nonvolatile phosphate buffer were identified and tracked by MS in the second dimension.     

HPLC‐DAD and HPLC‐ESI‐MS separation,determination and identification of the spin‐labeled diastereoisomers of podophyllotoxin

Spin‐labeled nitroxide derivatives of podophyllotoxin had better antitumor activity and less toxicity than that of the parent compounds. However, the 2‐H configurations of these spin‐labeled derivatives cannot be determined by nuclear magnetic resonance (NMR) methods. In the present paper, a high‐performance liquid chromatography‐diode array detection (HPLC‐DAD) and a high‐performance liquid chromatography‐electrospray ionization tandem mass spectrometry (HPLC‐ESI/MS/MS) method were developed and validated for the separation, identification of four pairs of diastereoisomers of spin‐labeled derivatives of podophyllotoxin at C‐2 position. In the HPLC‐ESI/MS spectra, each pair of diastereoisomers of the spin‐labeled derivatives in the mixture was directly confirmed and identified by [M+H]⁺ ions and ion ratios of relative abundance of [M‐ROH+H]⁺ (ion 397) to [M+H]⁺. When the [M‐ROH+H]⁺ ions (at m/z 397) were selected as the precursor ions to perform the MS/MS product ion scan. The product ions at m/z 313, 282, and 229 were the common diagnostic ions. The ion ratios of relative abundance of the [M‐ROH+H]⁺ (ion 397) to [M+H]⁺, [A+H]⁺ (ion 313) to [M‐ROH+H]⁺, [A+H‐OCH₃]⁺ (ion 282) to [M‐ROH+H]⁺ and [M‐ROH‐ArH+H]⁺ (ion 229) to [M‐ROH+H]⁺ of each pair of diastereoisomers of the derivatives specifically exhibited a stereochemical effect. Thus, by using identical chromatographic conditions, the combination of DAD and MS/MS data permitted the separation and identification of the four pairs of diastereoisomers of spin‐labeled derivatives of podophyllotoxin at C‐2 in the mixture.     

Multidimensional separation of tryptic peptides from human serum proteins using reversed‐phase,strong cation exchange,weak anion exchange,and fused‐core fluorinated stationary phases

Proteome profiling of crude serum is a challenging task due to the wide dynamic range of protein concentrations and the presence of high‐abundance proteins, which cover >90% of the total protein mass in serum. Peptide fractionation on strong cation exchange, weak anion exchange in the electrostatic repulsion hydrophilic interaction chromatography (ERLIC) mode, RP C₁₈ at pH 2.5 (low pH), fused‐core fluorinated at pH 2.5, and RP C₁₈ at pH 9.7 (high pH) stationary phases resulted in two to three times more identified proteins and three to four times more identified peptides in comparison with 1D nanoChip‐LC–MS/MS quadrupole TOF analysis (45 proteins, 185 peptides). The largest number of peptides and proteins was identified after prefractionation in the ERLIC mode due to the more uniform distribution of peptides among the collected fractions and on the RP column at high pH due to the high efficiency of RP separations and the complementary selectivity of both techniques to low‐pH RP chromatography. A 3D separation scheme combining ERLIC, high‐pH RP, and low‐pH nanoChip‐LC–MS/MS for crude serum proteome profiling resulted in the identification of 208 proteins and 1088 peptides with the lowest reported concentration of 11 ng/mL for heat shock protein 74.     

Low‐molecular‐weight color pI markers to monitor on‐line the peptide focusing process in OFFGEL fractionation

High‐throughput mass spectrometry‐based proteomic analysis requires peptide fractionation to simplify complex biological samples and increase proteome coverage. OFFGEL fractionation technology became a common method to separate peptides or proteins using isoelectric focusing in an immobilized pH gradient. However, the OFFGEL focusing process may be further optimized and controlled in terms of separation time and pI resolution. Here we evaluated OFFGEL technology to separate peptides from different samples in the presence of low‐molecular‐weight (LMW) color pI markers to visualize the focusing process. LMW color pI markers covering a large pH range were added to the peptide mixture before OFFGEL fractionation using a 24‐wells device encompassing the pH range 3–10. We also explored the impact of LMW color pI markers on peptide fractionation labeled previously for iTRAQ. Then, fractionated peptides were separated by RP_HPLC prior to MS analysis using MALDI‐TOF/TOF mass spectrometry in MS and MS/MS modes. Here we report the performance of the peptide focusing process in the presence of LMW color pI markers as on‐line trackers during the OFFGEL process and the possibility to use them as pI controls for peptide focusing. This method improves the workflow for peptide fractionation in a bottom‐up proteomic approach with or without iTRAQ labeling.     

Molecular mass ranges of coal tar pitch fractions by mass spectrometry and size‐exclusion chromatography

A coal tar pitch was fractionated by solvent solubility into heptane‐solubles, heptane‐insoluble/toluene‐solubles (asphaltenes), and toluene‐insolubles (preasphaltenes). The aim of the work was to compare the mass ranges of the different fractions by several different techniques. Thermogravimetric analysis, size‐exclusion chromatography (SEC) and UV‐fluorescence spectroscopy showed distinct differences between the three fractions in terms of volatility, molecular size ranges and the aromatic chromophore sizes present. The mass spectrometric methods used were gas chromatography/mass spectrometry (GC/MS), pyrolysis/GC/MS, electrospray ionization Fourier transform ion cyclotron resonance mass spectrometry (ESI‐FTICRMS) and laser desorption time‐of‐flight mass spectrometry (LD‐TOFMS). The first three techniques gave good mass spectra only for the heptane‐soluble fraction. Only LDMS gave signals from the toluene‐insolubles, indicating that the molecules were too involatile for GC and too complex to pyrolyze into small molecules during pyrolysis/GC/MS. ESI‐FTICRMS gave no signal for toluene‐insolubles probably because the fraction was insoluble in the methanol or acetonitrile, water and formic acid mixture used as solvent to the ESI source. LDMS was able to generate ions from each of the fractions. Fractionation of complex samples is necessary to separate smaller molecules to allow the use of higher laser fluences for the larger molecules and suppress the formation of ionized molecular clusters. The upper mass limit of the pitch was determined as between 5000 and 10 000 u. The pitch asphaltenes showed a peak of maximum intensity in the LDMS spectra at around m/z 400, in broad agreement with the estimate from SEC. The mass ranges of the toluene‐insoluble fraction found by LDMS and SEC (400–10 000 u with maximum intensity around 2000 u by LDMS and 100–9320 u with maximum intensity around 740 u by SEC) are higher than those for the asphaltene fraction (200–4000 u with maximum intensity around 400 u by LDMS and 100–2680 u with maximum intensity around 286 u by SEC) and greater than values considered appropriate for petroleum asphaltenes (300–1200 u with maximum intensity near 700 u). Copyright © 2009 John Wiley & Sons, Ltd.     

Characterization and identification of saponins in Achyranthes bidentata by rapid‐resolution liquid chromatography with electrospray ionization quadrupole time‐of‐flight tandem mass spectrometry

A rapid‐resolution liquid chromatography (RRLC) method coupled with electrospray ionization quadrupole time‐of‐flight tandem mass spectrometry (Q‐TOF MS/MS) has been developed for analysis of oleanane‐type triterpenoid saponins in Achyranthes bidentata. Collision‐induced dissociation techniques were used to fragment the precursor molecular ions and the resulting product ions. A retro‐Diels‐Alder rearrangement from the oleanane aglycone skeleton in the MS/MS process yielded characteristic fragment ions in positive ion mode. These characteristic ions were helpful in predicting the aglycone structure. Losses of monosaccharide sequences, presence of sugar‐chain fragment ions, and cleavage of CO₂ were observed for important information on sugar types and attachment sequences. Fragmentation rules of three major groups of saponins from A. bidentata were summarized, and the possible fragmentation pathways were proposed. A total of 22 compounds including both the target and unknown oleanane‐type triterpenoid saponins were rapidly screened and predicted in the herbal extract by the developed method. The RRLC‐Q‐TOF MS/MS method has provided a powerful approach for rapid separation, target screening and structural elucidation of oleanane‐type saponins, and also opened perspectives for similar studies on other herbal medicines. Copyright © 2010 John Wiley & Sons, Ltd.     

Solid‐Phase Synthesis of Polyamine Spider Toxins and Correlation with the Natural Products by HPLC‐MS/MS

A recently developed new and divergent approach for the solid‐phase synthesis of polyamines and polyamine derivatives was extended to the preparation of linear pentamines, and it was applied to the synthesis of three quartets of isomeric polyamine spider toxins. The twelve synthetic acylpolyamines were investigated by HPLC‐UV(DAD)‐MS and HPLC‐UV(DAD)‐MS/MS and compared with the natural products in the complex mixture of the venom of Agelenopsis aperta. The comparative investigation supported the structures and assignments of seven previously found toxins and allowed the identification of an additional five polyamine derivatives in the natural sample. The MS/MS study of the isomerically pure polyamine derivatives revealed furthermore a characteristic pattern for the fragmentation of these compounds, which can possibly be used as evidence in the trace analysis of other polyamine derivatives.     

Assessment of the hemolysis and endothelial cell cytotoxicity induced by residual linear alkylbenzene sulfonates on pharmaceutical rubber stoppers based on HPLC‐ESI‐MS

This study was designed to develop a high‐performance liquid chromatographic–electrospray ionization–mass spectrometry (HPLC‐ESI‐MS) method for quantitative determination of residual surfactant linear alkylbenzene sulfonate (LAS) compounds on pharmaceutical rubber stoppers. An HPLC‐ESI‐MS method was developed for separation and determination of five LAS homologs (C10–C14) under gradient conditions using methanol and ammonium acetate as mobile phases. Hemolysis activity of residual LAS compounds was analyzed by spectrophotometry. Expression of interleukin (IL)‐6 and tumor necrosis factor (TNF)‐α in human umbilical vein endothelial cells (HUVECs) after LAS compound treatment was examined by enzyme‐linked sorbent assay. LAS compounds were well separated and determined by the established gradient conditions. The linear range was 0.05–8 µg/mL with correlation coefficients ≥0.997. Recoveries were from 73 to 134% and the relative standard deviation was <13.7%. There was a correlation between hemolysis rate and LAS compounds concentration when it was ≥0.8 µg/cm². LAS compounds decreased the viability of HUVECs and promoted the production of IL‐6 and TNF‐α. The developed analytical method was successful for quantitative determination of residual LAS compounds on pharmaceutical rubber stoppers and it is important to monitor and control the amount of LAS compounds on rubber stoppers. Copyright © 2015 John Wiley & Sons, Ltd.     

Microfluidic HPLC‐Chip devices with integral channels containing methylstyrenic‐based monolithic media

Polyimide HPLC‐Chip devices containing poly(methylstyrene‐bis‐p‐vinylphenyl)ethane (MS/BVPE) stationary phase within the device channels and with wall attachment were prepared by thermally initiated free radical polymerization. The microfluidic devices were coupled to both UV and MS detectors. The potential of the MS/BVPE monolith as an alternative separation media within chip devices was investigated by side‐by‐side comparisons to particulate media within commercial devices. The chromatographic behavior of this stationary phase was comparable to particulate media for separations of proteins as the average peak width at half‐height was equal (6.2 s) for a separation within 8 min under gradient elution conditions. The ability to control the porosity characteristics of the MS/BVPE monolith with changes in polymerization time also extended its utility into small analyte (< 500 Da) applications, although more optimization is needed to match conventional RP media for these applications. The good mechanical stability of the MS/BVPE monolith within the microdevices enabled excellent run‐to‐run repeatability (%RSD retention time (? 0.16) and chip‐to‐chip reproducibility (%RSD retention time (1.4). The use of this material within enrichment channels also shows its potential value in more complex work flows.     

Application of bromoacetate‐substituted β‐CD‐bonded silica particles as chiral stationary phase for HPLC

Bromoacetate‐substituted [3‐(2‐O‐β‐cyclodextrin)‐2‐hydroxypropoxy]propylsilyl‐appended silica particles (BACD‐HPS), an important and useful synthetic intermediate for preparation of novel types of macrocycles‐capped β‐CD‐bonded silica particles including crown ether/cyclam/calix[4]arene‐capped β‐CD‐bonded silica particles, have been prepared and used as chiral stationary phase for HPLC. This synthetic stationary phase is characterized by means of elemental analysis. For the first time, the chromatographic behavior of BACD‐HPS was systematically evaluated with several disubstituted benzenes and some chiral drug compounds under both normal and RP conditions in HPLC. The results show that BACD‐HPS has excellent selectivity for the separation of aromatic positional isomers and chiral isomers of some drug compounds when used as stationary phase in HPLC.     

Two‐dimensional HPLC analysis of oligostyrenes: Comprehensive and online heart‐cutting techniques

2‐D HPLC incorporating two reversed phase (RP) environments was employed for the isolation of oligomers and their diastereomers of low molecular weight oligostyrenes. The operation of a comprehensive method of analysis was compared to a heart‐cutting approach. The comprehensive approach employed a high resolution diastereomer separation in the first dimension and a low peak capacity C18, high speed separation according to molecular weight. Because of solvent incompatibility between the dimensions in the comprehensive method, successful separation of the diastereomers of the oligomers was not possible. The heart‐cutting approach used a C18 monolith in the first dimension, which was selective only for molecular weight. Entire molecular weight fractions were then transported to the second dimension in an online heart‐cutting process for the separation of diastereomers. The heart‐cutting process was more successful in that 228 components of the 511 within the sample were recognized. This series of separations was undertaken in less than 6 h.     

Speciation Analysis of Thallium by Reversed‐phase Liquid Chromatography ‐ Inductively Coupled Plasma Mass Spectrometry

An inductively coupled plasma mass spectrometer (ICP‐MS) was used as a liquid chromatographic detector for the speciation analysis of thallium in environmental samples. In this study, ionic thallium species, namely Tl(I) and Tl(III) were well separated by reversed‐phase high performance liquid chromatography (RP‐HPLC) with a C8‐HPLC column as the stationary phase and 1 mmol L^?1 tetrabutylammonium phosphate (TBAP), 2 mmol L^?1 diethylenetriamine pentaacetic acid (DTPA) in 1% v/v methanol solution (pH 6) as the mobile phase. Effluent from the HPLC column was delivered to the nebulizer of the ICP‐MS for the determination of thallium. The separation was complete in less than 3 min. Detection limit was 0.002 μg L^?1 for both Tl(I) and Tl(III) compounds based on peak height. The relative standard deviation of the peak areas for five injections of a mixture containing 1 μg Tl L^?1 was better than 3.4%. The concentrations of Tl compounds were determined in standard reference materials, including NIST SRM 1643e Trace Elements in Water and NRCC NASS‐5 Open Ocean Seawater and water samples collected in Kaohsiung area, Taiwan. The HPLC‐ICP‐MS results of the reference samples agreed with the reference values. This method has also been applied to determine Tl(I) and Tl(III) compounds in custard apple (Annona squamosa) leaves collected from Chai‐shan Mountain, Kaohsiung and Taitung City, Taiwan. The thallium species were quantitatively leached from the leaves with a 5 mmol L^?1 DTPA in 100 mmol L^?1 ammonium acetate solution in an ultrasonic bath during a period of 30 min. The HPLC‐ICP‐MS result that was obtained after the analysis of leaves sample showed a satisfactory agreement with the total thallium concentration obtained by ICP‐MS analysis of completely dissolved sample.     

Ion‐pairing high‐performance liquid chromatography‐mass spectrometry of impurities and reduction products of sulphonated azodyes

An HPLC separation method with triethylammonium acetate mobile phase additive developed for the analysis of impurities in polysulphonated azo dyes provides good separation selectivity and compatibility with electrospray ionisation (ESI) mass spectrometry. The negative‐ion ESI mass spectra containing only peaks of deprotonated molecules [M–H]^– for monosulphonic acids, [M–xH]^x–, and sodiated adducts [M–(x + y)H + yNa]^x– for polysulphonic acids allow easy molecular mass determination of unknown impurities. Based on the knowledge of the molecular masses and of the fragment ions in the MS/MS spectra, probable structures of trace impurities in commercial dye samples are proposed. To assist in the interpretation of the mass spectra of complex polysulphonated azodyes, additional information can be obtained after chemical reduction of azodyes to aromatic amines. The structures of the non‐sulphonated reduction products can be determined by reversed‐phase HPLC/MS with positive‐ion atmospheric pressure chemical ionisation and of the sulphonated products by ion‐pairing HPLC/MS with negative‐ion ESI.     

The pre‐separation of oxygen containing compounds in oxidised heavy paraffinic fractions and their identification by GC‐MS with supersonic molecular beams.

The heavy petroleum fractions produced during refining processes need to be upgraded to useable products to increase their value. Hydrogenated heavy paraffinic fractions can be oxidised to produce high value products that contain a variety of oxygenates. These heavy oxygenated paraffinic fractions need to be characterised to enable the control of oxidation processes and to understand product properties. The accurate identification of the oxygenates present in these fractions by electron ionisation (EI) mass spectrometry is challenging due to the complexity of these heavy fractions. Adding to this challenge is the limited applicability of EI mass spectral libraries due to the absence of molecular ions from the EI mass spectra of many oxygenates. The separation of oxygenates from the complex hydrocarbon matrix prior to high temperature GC‐MS (HT‐GC‐MS) analysis reduces the complexity of these fractions and assists in the accurate identification of these oxygenates. Solid phase extraction (SPE) and supercritical fluid chromatography (SFC) were employed as prefractionation techniques. GC‐MS with supersonic molecular beams (SMBs) (also named GC‐MS with cold‐EI) utilises a SMB interface with which EI is done with vibrationally cold sample compounds in a fly‐through ion source (cold‐EI) resulting in a substantial increase in the molecular ion signal intensity in the mass spectrum. This greatly enhances the accurate identification of the oxygenates in these fractions. This study investigated the ionisation behaviour of oxygenated compounds using cold‐EI. The prefractionation by SPE and SFC and the subsequent analysis with GC‐MS with cold‐EI were applied to an oxygenated heavy paraffinic fraction.