Robust solvent‐free fabrication and characterization of (polydimethylsiloxane‐co‐2‐hydroxyethylmethacrylate)/poly (ethylene glycol) methacrylate (PDMS‐HEMA)/PEGMA hydrogels

Combining hydrophobic materials such as polydimethylsiloxane (PDMS), a natural hydrophobic material with typical hydrophilic monomers without using organic solvent remains a big challenge due to their extreme different properties; hence, fabricating a class of silicone hydrogels with two extremes without use of organic solvents could bring us a novel class of silicone hydrogels. Herein, a range of PDMS‐HEMA‐PEGMA hydrogels was prepared from hydroxyl‐terminated PDMS, 2‐hydroxyethylmethacrylate (HEMA), poly (ethylene glycol) methacrylate (PEGMA), and isophorone diisocyanate via condensation and radical copolymerization reactions. The infrared results confirmed the PDMS‐HEMA‐PEGMA network formation, while the hydrophilicity of the as‐prepared block copolymer was dependent on (PDMS‐HEMA)/PEGMA ratio. Increasing the PEGMA content resulted in increased equilibrium water content, phase separation, surface roughness, and tensile strength, while the tensile modulus, elongation at break, optical transmittance, water contact angle, and oxygen permeability (Dk) were decreasing. At PEGMA content of 28.3%, the relative protein adsorption ratio decreased to 20% and 36% for bovine serum albumin and lysozyme, respectively, compared with that of the control (PDMS‐HEMA), suggesting antiprotein adsorption ability. In overall, the results showed that the PDMS‐HEMA‐PEGMA hydrogels not only exhibited remarkable hydrophilicity and suppressed protein adsorption but also maintained higher optical transparency and oxygen permeability (Dk).     

Separation of nitrogen and oxygen gases by polymeric membrane embedded with magnetic nano‐particle

Asymmetric polyethersulfone (PES) micro‐porous flat sheet membranes were prepared by the phase inversion method (PIM) and used as the support. PES‐PDMS composite membranes were fabricated with coating polydimethylsiloxane on the surface of PES membrane. The FluidMAG‐PAD was coated on PES and PES‐PDMS membrane to prepare super‐paramagnetic membranes for separation of oxygen from nitrogen. Permeance and O₂/N₂ selectivity were evaluated in the absence or presence of external magnetic field. In the absence of external magnetic field, the super‐paramagnetic polymer provides larger surface area leading to extended sites for oxygen adsorption. In the presence of magnetic field, the super‐paramagnetic particles obtained magnetic property leading to a pronounced interaction with oxygen resulting in elevated selectivity and permeability. Copyright © 2011 John Wiley & Sons, Ltd.     

Hydrophilic surface modification of polydimetylsiloxane‐co‐2‐hydroxyethylmethacrylate (PDMS‐HEMA) by Silwet L‐77 (heptamethyltrisiloxane) surface treatment

Biomaterials and their host organism's quintessential place of interaction are the surfaces of materials, as transportation of liquids within microchannels requires hydrophilic surfaces. Modifying the hydrophobic surface of polydimethylsiloxane (PDMS) into a hydrophilic one which can be used in biomaterials remains a big challenge. Herein, PDMS‐hydroxyethylmethacrylate (HEMA) films were prepared by the condensation of PDMS using isophorone diisocyanate as a cross‐linker, followed by the incorporation of HEMA via radical copolymerization. The as‐prepared PDMS‐HEMA films were thereafter hydrophilized via physical treatment with heptamethyltrisiloxane. The surface properties of the obtained PDMS‐HEMA films were characterized in wettability, morphology, topography, swelling, mechanical properties, and protein adsorption. Compared to pristine PDMS‐HEMA as control, the surface wettability, roughness, and protein adsorption of the hydrophilized PDMS‐HEMA films were significantly improved while the films also exhibited excellent optical properties. However, the improvement of the swelling properties remains insignificant, indicating that the interior morphology was still based on the hydrophobic siloxane PDMS. The long‐term hydrophilicity was considered good as no significant hydrophobic recovery was noticeable in a period of 5 months after treatment.     

In Situ Generated Janus Fabrics for the Rapid and Efficient Separation of Oil from Oil‐in‐Water Emulsions

A cotton fabric was coated with a polymer that contains both poly(dimethyl siloxane) (PDMS) and poly(N,N‐dimethylaminoethyl methacrylate) (PDMAEMA). When the repeat unit number of PDMS is about three‐fold that of PDMAEMA and the fabric is exposed to air, the fabric is superhydrophobic because PDMS in the coating covers the PDMAEMA chains. Upon contact with an oil‐in‐water emulsion, the water‐soluble PDMAEMA rises to the top and the side in contact with the emulsion becomes hydrophilic. The emerged PDMAEMA chains then cause the emulsion droplets to coagulate, and the aggregated oil fills the pores on the superhydrophobic side of the fabric. The oil‐impregnated side remains hydrophobic even upon prolonged contact with water. Thus, a Janus fabric is elegantly generated in situ and sustained. This easy‐to‐prepare Janus fabric rapidly and efficiently separates oil from emulsions and may find practical applications.     

Suppression of surface pattern formation in spin‐coated polymer films by the addition of polydimethylsiloxane‐grafted silica nanoparticles

Polydimethylsiloxane (PDMS)‐grafted nanoparticles and PDMS were added, respectively, to inhibit the dewetting of polymer films and the formation of surface patterns in spin coating. Uniform and flat films were successfully achieved with the addition of PDMS‐grafted silica nanoparticles or PDMS. Time‐of‐flight secondary ion mass spectrometry depth profiling indicated that PDMS‐grafted silica nanoparticles and PDMS preferentially segregated to the surface. A high concentration of bromine end groups was observed at the interface. The surface layer of PDMS or PDMS‐grafted silica nanoparticles can decrease the surface tension of the polymer solutions and reduce the evaporation rates of the solvents, providing more time for the bromine end groups to anchor themselves at the silicon substrates. Copyright © 2016 John Wiley & Sons, Ltd.     

Synthesis and characterization of novel PDMS nanocomposites using POSS derivatives as cross‐linking filler

We report the synthesis and characterization of novel elastomeric nanocomposites containing polyhedral oligomeric silsesquioxanes (POSS) as both the cross‐linker and filler within a polydimethylsiloxane (PDMS) polymer matrix. These polymer composites were prepared through the reaction of octasilane‐POSS (OS‐POSS) with vinyl‐terminated PDMS chains using hydrosilylation chemistry. In addition, larger super‐POSS cross‐linkers, consisting of two pendant hepta(isobutyl)POSS molecules attached to a central octasilane‐POSS core, were also used in the fabrication of the PDMS composites. The chemical incorporation of these POSS cross‐linkers into the PDMS network was verified by solid‐state ¹H magic angle spinning NMR. Based on dynamic mechanical analysis, the PDMS nanocomposites prepared with the octafunctional OS‐POSS cross‐linker exhibited enhanced mechanical properties relative to polymer systems prepared with the tetrafunctional TDSS cross‐linker at equivalent loading levels. The observed improvements in mechanical properties can be attributed to the increased dimensionality of the POSS cross‐linker. The PDMS elastomers synthesized from the larger super‐POSS molecule showed improved mechanical properties relative to both the TDSS and OS‐POSS composites due to the increased volume‐fraction of POSS filler in the polymer matrix. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2589–2596, 2009     

Electrochemical impedance spectroscopy and in situ UV‐vis spectroelectrochemistry studies of Poly(N‐vinyl carbazole)/ Polydimethylsiloxane composite electrodes

Poly(N‐vinyl carbazole)/polydimethylsiloxane (PNVCz/PDMS) composite electrodes were prepared by electrochemical polymerization of NVCz monomer onto PDMS‐coated platinum (Pt) and glassy carbon (GC) electrode surfaces to investigate the influence of the insulating constituent, PDMS and process temperature on the capacitive performance of the coated layers. The electrochemical properties of the bilayer coatings were studied by electrochemical impedance spectroscopy and UV‐vis spectroelectrochemistry measurements. The low‐frequencies capacitance values of composite electrodes indicated that the capacitive behaviors of the composites decreased with increasing PDMS content (from 5.0 to 10.0; in wt/v%) in coating solutions at 25 °C, and with decreasing coating temperatures (from 25 °C to ? 15 °C) of PDMS and PNVCz and, more resist PDMS/PNVCz layers formed. Copyright © 2011 John Wiley & Sons, Ltd.     

A novel fabrication technique to minimize poly(dimethylsiloxane)‐microchannels deformation under high‐pressure operation

PDMS is one of the most common materials used for the flow delivery in the microfluidics chips, since it is clear, inert, nontoxic, and nonflammable. Its inexpensiveness, straightforward fabrication, and biological compatibility have made it a favorite material in the exploratory stages of the bio‐microfluidic devices. If small footprint assays want to be performed while keeping the throughput, high pressure‐rated channels should be used, but PDMS flexibility causes an important issue since it can generate a large variation of microchannel geometry. In this work, a novel fabrication technique based on the prevention of PDMS deformation is developed. A photo‐sensible thiolene resin (Norland Optical Adhesive 63, NOA 63) is used to create a rigid coating layer over the stiff PDMS micropillar array, which significantly reduces the pressure‐induced shape changes. This method uses the exact same soft lithography manufacturing equipment. The verification of the presented technique was investigated experimentally and numerically and the manufactured samples showed a deformation 70% lower than PDMS conventional samples.     

A facile approach to fabricate hierarchically structured poly(3‐hexylthiophene‐2,5‐diyl) films

Microstructured surfaces have great potentials to improve the performances and efficiency of optoelectronic devices. In this work, a simple robust approach based on surface instabilities was presented to fabricate poly(3‐hexylthiophene‐2,5‐diyl) (P3HT) films with ridge‐like/wrinkled composite microstructures. Namely, the hierarchically patterned films were prepared by spin coating the P3HT/tetrahydrofuran (THF) solution on a polydimethylsiloxane (PDMS) substrate to form stable ridge‐like structures, followed by solvent vapor swelling to create surface wrinkles with the orientation guided by the ridge‐like structures. During spin coating of the P3HT/THF solution, the ridge‐like structures were generated by the in‐situ template of the THF swelling‐induced creasing structures on the PDMS substrate. To our knowledge, it is the first report that the creasing structures are used as a recoverable template for patterning films. The crease‐templated ridge‐like structures were well modulated by the THF swelling time, the modulus of the PDMS substrate, the P3HT/THF solution concentration and the selective/blanket exposure of the PDMS substrate to O₂ plasma. UV–vis and fluorescence spectrometry measurements indicated that the light absorption and fluorescent emission were improved on the hierarchically patterned P3HT films, which can be utilized to enhance the efficiencies of organic solar cells. Furthermore, this simple versatile method based on the solvent swelling‐induced crease as the in‐situ recoverable template has been extended to pattern other spin‐coated films with different compositions. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 928–939     

Super‐Hydrophobic PDMS Surface with Ultra‐Low Adhesive Force

Summary: Rough polydimethylsiloxane (PDMS) surface containing micro‐, submicro‐ and nano‐composite structures was fabricated using a facile one‐step laser etching method. Such surface shows a super‐hydrophobic character with contact angle higher than 160° and sliding angle lower than 5°, i.e. self‐cleaning effect like lotus leaf. The wettabilities of the rough PDMS surfaces can be tunable by simply controlling the size of etched microstructures. The adhesive force between etched PDMS surface and water droplet is evaluated, and the structure effect is deduced by comparing it with those own a single nano‐ or micro‐scale structures. This super‐hydrophobic PDMS surface can be widely applied to many areas such as liquid transportation without loss, and micro‐pump (creating pushing‐force) needless micro‐fluidic devices.

Etched PDMS surface containing micro‐, submicro‐, and nano‐composite structures shows a self‐cleaning effect with water CA as high as 162° and SA lower than 5°.     

Reverse hydrophobic PDMS surface to hydrophilic by 1‐step hydrolysis reaction

Hydrophilic modification on the surface of polymer polydimethylsiloxane (PDMS) material is a key step for its application in biomaterial, bioengineering, and so on. In this article, a novel and effective method was proposed to reverse hydrophobic surface to hydrophilic by 1‐step hydrolysis of Si―O bond to produce hydrophilic hydroxyl group. The hydrophilizing reagent 2‐(trimethylsiloxy) ethyl methacrylate (TMSEMA) was used during the copolymerization of polydimethylsiloxane prepolymer (DMS U21). The prepared PDMS film was subjected to 1‐step surface hydrophilic reversal treatment using KOH solution to produce hydroxyl groups on the surface. The contact angle, attenuated total reflection Fourier transform infrared spectra, and equilibrium water content (EWC) measurements were conducted on PDMS films. The results showed that TMSEMA content had no obvious impact on the contact angle and EWC value of untreated PDMS. After reversal treatment, the contact angle decreased from 94° to 15°, and the EWC value increases to 10% when the TMSEMA content was 15 wt%. The spectrum proved that the reverse reaction produced hydroxyl and carboxylate on the surface. The hydrophilic stability, surface morphology, and protein adsorption properties of PDMS film were also investigated. This study can provide new ideas and further reference for improving the hydrophilicity of PDMS surface.     

Fabricating Super‐Hydrophobic Lotus‐Leaf‐Like Surfaces through Soft‐Lithographic Imprinting

Summary: A soft‐lithographic imprinting approach to fabricate super‐hydrophobic surfaces has been developed in this work. In this process, fresh lotus leaves were used as masters and PDMS stamps were prepared by replica molding against the lotus‐leaf surfaces. By using the stamps and an epoxy‐based azo polymer solution as “ink”, the mimicked lotus‐leaf surfaces made of the polymer were fabricated by pressing the featured faces of the stamps against “inked” substrates and drying under a proper condition after peeling off the stamps. The lotus‐leaf‐like surfaces show super‐hydrophobic characteristics with the water contact angle higher than 150° and contact angle hysteresis less than 3°.

SEM images of lotus‐leaf‐like papillary structures on the imprinted surface.     

One‐step preparation and application of mussel‐inspired poly(norepinephrine)‐coated polydimethylsiloxane microchip for separation of chiral compounds

In this paper, using the self‐polymerization of norepinephrine (NE) and its favorable film‐forming property, a simple and green preparation approach was developed to modify a PDMS channel for enantioseparation of chiral compounds. After the PDMS microchip was filled with NE solution, poly(norepinephrine) (PNE) film was gradually formed and deposited on the inner wall of microchannel as permanent coating via the oxidation of NE by the oxygen dissolved in the solution. Due to possessing plentiful catechol and amine functional groups, the PNE‐coated PDMS microchip exhibited much better wettability, more stable and suppressed EOF, and less nonspecific adsorption. The water contact angle and EOF of PNE‐coated PDMS substrate were measured to be 13° and 1.68 × 10^?4 cm² V^?1 s^?1, compared to those of 108° and 2.24 × 10^?4 cm² V^?1 s^?1 from the untreated one, respectively. Different kinds of chiral compounds, such as amino acid enantiomer, drug enantiomer, and peptide enantiomer were efficiently separated utilizing a separation length of 37 mm coupled with in‐column amperometric detection on the PNE‐coated PDMS microchips. This facile mussel‐inspired PNE‐based microchip system exhibited strong recognition ability, high‐performance, admirable reproducibility, and stability, which may have potential use in the complex biological analysis.     

Surface roughness and hydrophilicity enhancement of polyolefin‐based membranes by three kinds of plasma methods

The introduction of antibacterial property, conductivity, wettability and antithrombogenicity into polyolefin‐based membranes has evoked much attention, which can be achieved by coating hydrophilic polymers. Therefore, it is necessary to modify the roughness and hydrophilicity of polyolefin‐based membranes to enhance the coating ability. In this paper, three kinds of plasma methods, including inductively coupled (ICP) plasma, radio frequency low pressure (RFP) plasma and atmospheric dielectric barrier discharge (DBD) plasma, were used to modify the surface of the polyethylene (PE), polypropylene (PP) and polyester‐polypropylene (PET–PP) membranes. The surface roughness of the plasma‐modified PE, PP and PET–PP films was investigated by scanning electron microscopy (SEM) and atomic force microscope (AFM). The polar functional groups of films were observed by energy dispersive spectrometer (EDX) and X‐ray photoelectron spectroscopy (XPS). Besides, the hydrophilicity of the plasma‐modified PE, PP and PET–PP films was evaluated by water contact angle measurement. It was found that the surface roughness and hydrophilicity of plasma‐modified PE, PP and PET–PP films increased with the generation of oxygen‐containing functional groups (i.e. C―O, and C?O). The PET–PP membranes were treated by RFP plasma at different processing powers and times. These results indicated that plasma is an effective way to modify films, and the treatment time and power of plasma had a certain accumulation effect on the membranes' hydrophilicity. As for the roughness and hydrophilicity, the DBD plasma modifies the PE film, which is the optimum way to get the ideal roughness and hydrophilicity. Copyright © 2015 John Wiley & Sons, Ltd.     

High‐performance thin film composite membranes with well‐defined poly(dimethylsiloxane)‐b‐poly(ethylene glycol) copolymer additives for CO2 separation

A series of well‐defined diblock copolymers (BCPs) consisting of poly(ethylene glycol) (PEG) and poly(dimethylsiloxane) (PDMS) were synthesized and blended with commercially available PEBAX® 2533 to form the active layer of thin‐film composite (TFC) membranes, via spin‐coating. BCPs with a PEG component ranging from 1 to 10 kDa and a PDMS component ranging from 1 to 10 kDa were synthesized by a facile condensation reaction of hydroxyl terminated PEG and carboxylic acid functionalized PDMS. The BCP/PEBAX® 2533 blends up to 50 wt % on cross‐linked PDMS gutter layers were tested at 35 °C and 350 kPa. TFC membranes containing BCPs of 1 kDa PEG and 1–5 kDa PDMS produced optimal results with CO₂ permeances of approximately 1000 GPU which is an increase up to 250% of the permeance of pure PEBAX® 2533 composite membranes, while maintaining a CO₂/N₂ selectivity of 21. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1500–1511     

Composites of poly (dimethylsiloxane) and spherically shaped poly (2‐hydroxyethylmethacrylate) particles for biomedical use

Silicone rubbers have shown considerable promise in the biomedical field, but their hydrophobicity leads to serious problems in long‐term implants. In our study, composites of poly (dimethylsiloxane) (PDMS) and spherically shaped poly (2‐hydroxyethylmethacrylate) (PHEMA) microparticles were prepared. Unlike previous silicone hydrogel composites, suspension polymerization was carried out in an aqueous medium to prepare PHEMA particles directly, which avoided the removal of organic phase and give hydrogel particles with high purity. Very fine PHEMA particles with uniform geometry and small size were obtained through various influencing factors during their formation. Through the introduction of PHEMA particles, PDMS matrix was endowed with hydrophilicity to a certain extent. With an increase in hydrogel content, higher swelling ability and surface wettability of the composites were observed. We have also demonstrated that smaller sized particles are more favorable for hydrophilicity improvement. The results of improved swelling ability, surface wettability, and low affinity to lipid show that this composite material is suitable for biomedical use. Copyright © 2009 John Wiley & Sons, Ltd.     

Ultra‐rapid non‐equilibrium solid‐phase microextraction at elevated temperatures and direct coupling to mass spectrometry for the analysis of lidocaine in urine

Solid‐phase microextraction (SPME) has been directly coupled to an ion‐trap mass spectrometer (MS) for the determination of the model compound lidocaine in urine, hereby applying MS/MS [fragmentation of [M + H]⁺ (m/z 235) to a fragment with m/z 86]. The throughput of samples has been increased using non‐equilibrium SPME with polydimethylsiloxane (PDMS) fibers. The effect of temperature on the sorption and the desorption was studied. Elevated temperatures during sorption (65°C) and desorption (55°C) had a considerable influence on the speed of the extraction. The desorption was carried out with a home‐made desorption chamber allowing thermostating. Only 1 min sorption and 1 min desorption were performed, after which MS detection took place, resulting in a total analysis time of 3 min. Detection limits below 1 ng/mL could be obtained despite yields of only 2.1 and 1.5% for a 100‐ and a 30‐μm PDMS‐coated fiber, respectively. Furthermore, the determination of lidocaine in urine had acceptable reproducibilities, i.e., relative standard deviations (RSDs) below 10%. A limit of quantitation (RSD < 15%) of about 1 ng/mL was obtained. No extra wash step of the extraction fiber was required after desorption if a 30‐μm coating was used, whereas not all the analyte was desorbed from the 100‐μm coating in a single desorption. Therefore, the SPME‐MS/MS system with a 30‐μm PDMS‐coated fiber for rapid non‐equilibrium SPME at elevated temperatures has interesting potential for high‐throughput analysis of biological samples.     

Responsive microgrooves for the formation of harvestable tissue constructs

Given its biocompatibility, elasticity, and gas permeability, poly(dimethylsiloxane) (PDMS) is widely used to fabricate microgrooves and microfluidic devices for three-dimensional (3D) cell culture studies. However, conformal coating of complex PDMS devices prepared by standard microfabrication techniques with desired chemical functionality is challenging. This study describes the conformal coating of PDMS microgrooves with poly(N-isopropylacrylamide) (PNIPAAm) by using initiated chemical vapor deposition (iCVD). These microgrooves guided the formation of tissue constructs from NIH-3T3 fibroblasts that could be retrieved by the temperature-dependent swelling property and hydrophilicity change of the PNIPAAm. The thickness of swollen PNIPAAm films at 24 °C was approximately 3 times greater than at 37 °C. Furthermore, PNIPAAm-coated microgroove surfaces exhibit increased hydrophilicity at 24 °C (contact angle θ = 30° ± 2) compared to 37 °C (θ = 50° ± 1). Thus PNIPAAm film on the microgrooves exhibits responsive swelling with higher hydrophilicity at room temperature, which could be used to retrieve tissue constructs. The resulting tissue constructs were the same size as the grooves and could be used as modules in tissue fabrication. Given its ability to form and retrieve cell aggregates and its integration with standard microfabrication, PNIPAAm-coated PDMS templates may become useful for 3D cell culture applications in tissue engineering and drug discovery.     

Facile non‐lithographic route to highly aligned silica nanopatterns using unidirectionally aligned polystyrene‐block‐polydimethylsiloxane films

Thin films (monolayer and bilayer) of cylinder forming polystyrene‐block‐polydimethylsiloxane (PS‐b‐PDMS) were shear aligned by the swelling and deswelling of a crosslinked PDMS pad that was physically adhered to the film during solvent vapor annealing. The nanostructures formed by self‐assembly were exposed to ultraviolet‐ozone to partially oxidize the PDMS, followed by calcination in air at 500 °C. In this process, the PS segments were fully decomposed, while the PDMS yielded silica nanostructures. The highly aligned PDMS cylinders were thus deposited as silica nanolines on the silicon substrate. Using a bilayer film, the center‐to‐center distance of these features were effectively halved from 38 to 19 nm. Similarly, by sequential shear‐alignment of two distinct layers, a rhombic array of silica nanolines was fabricated. This methodology provides a facile route to fabricating complex topographically patterned nanostructures. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1058–1064     

PDMS network blends of amphiphilic acrylic copolymers with poly(ethylene glycol)‐fluoroalkyl side chains for fouling‐release coatings. I. Chemistry and stability of the film surface

Amphiphilic copolymers of a methacrylic monomer (SiMA) carrying a polysiloxane side chain and an acrylic monomer (ZA) with a mixed poly(ethylene glycol) (PEG)‐fluoroalkyl side chain (10–85 mol % ZA) were incorporated as the surface‐active components into poly(dimethylsiloxane) (PDMS) network blends at different loadings (1 and 4 wt % with respect to PDMS). Wettability of the coating surfaces was investigated by contact angle measurements, and their surface chemical composition was determined by angle‐resolved X‐ray photoelectron spectroscopy. It was found that the surface segregation of the fluoroalkyl segments of the amphiphilic copolymers was responsible for the high enrichment in fluorine concentration within 10 nm of the coating surface. The PEG segments were also concentrated at the polymer?air interface. The chemical composition of the films was proven to be relatively little affected by immersion in water. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012