Molecular weight characterization of soluble high performance polyimides. 2. Validity of universal SEC calibration and absolute molecular weight calculation

Six different soluble high-performance aromatic polyimides, each prepared by solution imidization to three controlled average molecular weights, were analyzed by size exclusion chromatography (SEC) using on-line parallel coupled refractometric and viscometric detectors. N-methylpyrrolidone (NMP) with 0.06 M LiBr and NMP stirred over P₂O₅ were used as mobile phase for four of the polyimides; NMP with 0.06 M LiBr and NMP stirred over P₂O₅ were used as mobile phases for four of the polyimides; NMP with 0.06 M LiBr tetrahydrofuran (THF) and chloroform served as mobile phases for the other two polyimides. For all the samples the stationary phase in the SEC columns was cross-linked polystyrene beads. Molecular weight averages of the polyimides were calculated using universal SEC calibration with polystyrene standards in each solvent. The agreement of the calculated molecular weight averages in the different solvents confirms that the universal SEC calibrations are valid for these semiflexible polymers. There was good agreement with weightaverage molecular weights obtained by low-angle laser light scattering (LALLS) performed in pure NMP. Intrinsic viscosity and molecular weight data for a series of nine samples of one polyimide covering a M_w = 20,000–70,000 g mol^–1 interval were treated to obtain Mark-Houwink-Sakurada constants. Unperturbed chain dimensions of this polyimide were obtained by application of the Stockmayer-Fixman extrapolation procedure to these data. ©1995 John Wiley & Sons, Inc.     

Molecular Weight and Aggregation of Erwinia Gum in Aqueous Solutions

Erwinia(E) gum is composed of glucose, fucose, galactose and glucuronic acid. The weight-average molecular weights Mw, number-average molecular weights Mn and intrinsic viscosities[η] of the four fractions and the unfractionated E gum in aqueous solutions at desired temperatures were studied by light scattering, membrane osmometry, size exclusion chromatography(SEC) and viscometry. The experimental results prove that E gum formed aggregates in the aqueous solution at 25 ℃ and the aggregates were broken gradually with increasing temperature. The dissociation of the aggregates of E gum in the aqueous solution started at 36 ℃, and was completed at around 90 ℃. The [η] values of E gum and its fractions are much higher than those of the conventional polymers with the similar molecular weights, and decrease with increasing NaCl concentration.     

Analysis of reduced monoclonal antibodies using size exclusion chromatography coupled with mass spectrometry

Size-exclusion chromatography (SEC) has been widely used to detect antibody aggregates, monomer, and fragments. SEC coupled to mass spectrometry has been reported to measure the molecular weights of antibody; antibody conjugates, and antibody light chain and heavy chain. In this study, separation of antibody light chain and heavy chain by SEC and direct coupling to a mass spectrometer was further studied. It was determined that employing mobile phases containing acetonitrile, trifluoroacetic acid, and formic acid allowed the separation of antibody light chain and heavy chain after reduction by SEC. In addition, this mobile phase allowed the coupling of SEC to a mass spectrometer to obtain a direct molecular weight measurement. The application of the SEC-MS method was demonstrated by the separation of the light chain and the heavy chain of multiple recombinant monoclonal antibodies. In addition, separation of a thioether linked light chain and heavy chain from the free light chain and the free heavy chain of a recombinant monoclonal antibody after reduction was also achieved. This optimized method provided a separation of antibody light chain and heavy chain based on size and allowed a direct measurement of molecular weights by mass spectrometry. In addition, this method may help to identify peaks eluting from SEC column directly.     

Characterization of implant device materials using size-exclusion chromatography with mass spectrometry and with triple detection

A more complete understanding of the raw materials used for making implant device materials becomes increasingly important in the medical device industry. Often such detailed information requires utilization of a combination of analytical techniques. In this work, we characterize a poly(dimethyl siloxane) (PDMS) material using on-line size exclusion chromatography (SEC) with electrospray ionization (ESI) and matrix assisted laser desorption ionization (MALDI) mass spectrometry (MS) techniques. Here, we obtain detailed molecular compositional information such as repeat units, end group chemistry, and identification of impurities in both the high and low mass range. SEC with light scattering, viscosity, and refractive index detection (triple detection) is used to obtain information on a small quantity of high mass impurity that was undetected by both SEC-ESI and MALDI MS techniques. SEC with triple detection measures absolute molecular weights and molecular weight distributions. We compare average molecular weight values of the implantable device polymer obtained by SEC with triple detection, SEC-ESI, and SEC-MALDI MS techniques.     

New Chromatographic and Hyphenated Techniques for Hydrophilic Copolymers

Most synthetic polymers are distributed in more than one parameter of molecular heterogeneity. For hydrophobic copolymers there are different chromatographic techniques available to analyse these distributions. As a result of the increasing interest in hydrophilic polymers and copolymers new chromatographic techniques are developed for the characterization of these polymers as well. However, very frequently these polymers contain highly polar or charged functional groups making them soluble only in aqueous mobile phases. There are several problems related to the use of aqueous mobile phases in polymer chromatography. Even the SEC analysis of such copolymers is not straightforward. As for HPLC in aqueous mobile phases, there are only a few applications in the literature so far. In addition to the fact that only a very limited number of stationary phases is available for aqueous HPLC of polymers, the interactions of polyelectrolytes in such chromatographic systems are not well understood. The present paper addresses the problems related to the application of SEC and HPLC in aqueous mobile phases. For graft copolymers with a polyethylene oxide backbone, e.g. PEG-g-polymethacrylic acid and PEG-g-polyvinyl alcohol, it will be shown that methods can be developed that give accurate molar mass and chemical composition information. Two-dimensional chromatography where aqueous HPLC and SEC are coupled on-line will be shown to be the most powerful analysis tool for the analysis of such copolymers. The hyphenation of the chromatographic separation techniques with spectroscopic detection techniques provides further insight into the molecular complexity of these copolymers.     

Size Exclusion Chromatography of Nonionic and Anionic Copolymers of Vinylpyrrolidone

Abstract

Size exclusion chromatography (SEC) of poly(vinylpyrrolidoneco-vinylacetate), PVPVA, and poly(vinylpyrrolidone-co-dimethylamincethylmethacrylate-co-vinylcaprolactan),PVPDMMAEMAVC, is evaluated in terms of resolution between polymer and solvent peaks using aqueous and nonaqueous mobile phases. A 1:1 (v/v) water/methanol, 0.1M LiNO₂ mobile phase is used with four Waters Ultrahydrogel columns with pore sizes of 120Å, 500Å, 1000Å, and 2000Å. DMF, 0.1M LiNO₃ mobile phase is used with three different two column sets. Two of the column sets are comprised of a mixed bed packing of poly(styrene-co-divinyl benzene), obtained from Shodex (KD80M), followed by either an Ultrahydrogel 120Å or a PLge1 100Å. The third two column set is a PLge1 10⁴Å followed by a PLgel 500Å. Any of the second columns in these sets improve separation between the trailing end of the polymer peak and the leading end of the solvent peak but the column set using an Ultrahydrogel 120Å yields a separation of these peaks whose valley is closer to the baseline. The aqueous mobile phase with the four column set yields a separation between the trailing end of the polymer peak and the leading end of the solvent peak whose valley is closest to the baseline. Recovery of PVPVA and PVPDMAEMAVC from the columns evaluated is 100%. Vinylpyrrolidone compositions of PVPVA ranging from 30 to 70 mole % were studied using both mobile phases. SEC of     

An Eluent Pressure Detector for Aqueous Size Exclusion Chrohatography

Abstract

An on-line viscometer which measures the eluent pressure drop across a long capillary was developed for use in aqueous size exclusion chromatography (SEC). Intrinsic viscosities of several polymer standards were calculated from data collected by the viscometer. These viscosities agree well with the measurements made with a Ubbelohde four-bulb shear dilution viscometer. The on-line viscometer becomes more sensitive as polymer hydro-dynamic volume increases. Therefore, it can be more effective than a refractive index detector for SEC analysis of high molecular weight, water soluble polymers.     

Elution Behavior of Oligomers on a Polyvinyl Alcohol Gel Column with Chloroform,Methanol, and Their Mixtures

Abstract

Elution phenomena of size exclusion chromatography (SEC) plus superimposed adsorption effects for oligostyrenes, epoxy resins, methylated melamine-formaldehyde resin prepolymers, p-cresolformaldehyde resin prepolymers, and phenol-formaldehyde resin prepolymers were investigated. SEC and superimposed adsorption effects could be elucidated from a concept of solubility parameter. Minimum retention volumes of these oligomers were obtained with the mobile phases of chloroform/methanol, 80/20 or 60/40 (v/v), and separation was expected to be mostly performed by SEC. The solubility parameter of polyvinyl alcohol gels was estimated to be between 21 and 23 from the above results. Elution for normal phase chromatography was in the order of increasing molecular weight and that for reversed-phase chromatography was in the order of decreasing molecular weight. These are reversed phenomena to those for low-molecular weight compounds. Solubility of sample solutes to mobile phase must be considered. Methanol mobile phase-polyvinyl alcohol gel system might be exception.     

Size-exclusion separation of proteins using a biocompatible polymeric monolithic capillary column with mesoporosity

Biocompatible poly(ethylene glycol methyl ether acrylate-co-polyethylene glycol diacrylate) monoliths were prepared for size exclusion chromatography (SEC) of proteins in the capillary format using Brij 58P in a mixture of hexanes and dodecanol as porogens. The monolithic columns provided size separation of four proteins in 20 mM sodium phosphate buffer (pH 7.0) containing 0.15 M NaCl, and there was a linear relationship between the retention times and the logarithmic values of the molecular weights. Compared to SEC monoliths previously synthesized using a triblock copolymer of polyethylene oxide and polypropylene oxide, an increase in mesoporosity was confirmed by inverse size exclusion chromatography. As a result, improved protein separation in the high molecular weight range and reduced column back-pressure were observed.     

Physicochemical properties of enhanced-fluidity liquid solvents

Enhanced fluidity (EF) liquid mixtures are advantageous as mobile phases for the separation of moderate to polar compounds in liquid chromatography (reversed-phase, normal, size exclusion, size exclusion, and chiral separations). The low viscosities and high diffusivities of EF mixtures allow highly efficient separations to be achieved in a small amount of time. The best use of enhanced-fluidity liquids is only possible when their physicochemical properties are known. Herein, the techniques used to measure the physicochemical properties (phase diagram, diffusivity, solvent strength and pH) of EF liquids are described. For each technique, the experiment design and the care necessary to insure the quality of the collected data are described. Finally, the impact of the measured physicochemical properties on the chromatography is also highlighted.     

Dichloropentafluoropropanes as solvents for size exclusion chromatography

We have found that HCFC225s (HCFC225ca: 3,3-dichloro-1,1,1,2,2-pentafluoropropane, HCFC225cb: 1,3-dichloro-1,1,2,2,3-pentafluoropropane) are superior mobile phases for size exclusion chromatography (SEC). As alternatives of CFC113, they have been shown to possess a number of excellent properties, such as low flammability, low viscosity, low cost, high purity, and environmental and operational friendliness. In addition, they have distinct advantages for the SEC measurement, because they solubilize some kinds of acrylate such as poly(methyl methacrylate) (PMMA) and commercial monodispersed PMMA can be used to prepare calibration curves necessary for the measurement of equivalent molecular weight of some polymers. Furthermore, we propose an HCFC225/1,1,1,3,3,3-hexafluoroisopropanol mixed solvent for use in the SEC of poly(ethylene terephthalate) (PET) and polyamides. Poly(2-(perfluorooctyl)ethyl acrylate), whose PMMA equivalent weight average molecular weight was 118,100 Da, was evaluated by a multi-angle laser light scattering (MALLS) detector to have an absolute molecular weight of 439,000 Da. The difference can be attributed to the molecular size of the polyfluorinated polymer compared to the non-fluorinated one. The possible application of this novel mobile phase system for molecular size and molecular weight characterization of perfluoropolyethers, PET, nylon 6 and nylon 6,6 are also discussed.     

Separation behavior of basic compounds on unbonded silicon oxynitride and silica high‐performance liquid chromatography stationary phases with reversed‐phase eluents

Unbonded silicon oxynitride and silica high‐performance liquid chromatography stationary phases have been evaluated and compared for the separation of basic compounds of differing molecular weight, pK_a, and log D using aqueous/organic mobile phases. The influences of percentage of organic modifier, buffer pH, and concentration in the mobile phase on base retention were investigated on unbonded silicon oxynitride and silica phases. The results confirmed that unbonded silicon oxynitride and silica phases demonstrated excellent separation performance for model basic compounds and both the unbonded phases examined possessed a hydrophobic/adsorption and ion‐exchange character. The silicon oxynitride stationary phase exhibited high hydrophilicity compared with silica with a reversed‐phase mobile phase. An ion‐exclusion‐type mechanism becomes predominant for the separation of three aimed bases on the silicon oxynitride column at pH 2.8. Different from silicon oxynitride stationary phase, no obvious change for the retention time of three model bases on silica stationary phase at pH 2.8 can be observed.     

Liquid chromatography techniques for characterizing poly(Vinyl Alcohol)

Poly(vinyl alcohol) (PVOH) samples may contain several heterogeneities requiring the development of chromatographic techniques for characterization. Size exclusion separations have been carried out using a number of aqueous eluents, incorporating electrolyte, or electrolyte/organic modifier, or surfactant. The most favourable molecular size separation was obtained using 0.25% w/v sodium lauryl sulfate as eluent. Reasonable values for molecular weights of PVOH samples have been determined. Compositional distributions in copolymer systems can be assessed using high-performance liquid chromatography employing a reversed-phase separation mechanism. For poly(vinyl alcohol), gradient elution with water/tetrahydrofuran (THF) with a wide pore polystyrene-based packing produced separations dependent on degree of hydrolysis and sequence length distribution. The elution results were verified with a column packed with non-porous beads. Partially hydrolysed PVOH samples appeared to have a broad distribution of composition.     

Molecular weight characterization of soluble high performance polyimides. 1. Polymer-solvent-stationary phase interactions in size exclusion chromatography

Soluble, fully cyclized m-amino phenyl acetylene terminated polyimides based on several anhydride/diamine monomers were prepared in N-methylpyrrolidine (NMP) and cyclized by solution imidization to controlled molecular weight. The polyimides and a polyamic acid precursor were successfully analyzed by size exclusion chromatography (SEC) utilizing online parallel coupled refractive index and differential viscometer detectors. The calculated M _nvalues were varied from 3,000 to 20,000 daltons. N-methylpyrrolidone (NMP), tetrahydrofuran (THF), and chloroform served as mobile phases for the cross-linked polystyrene gel packings. Normal retention behavior of the polyimides was observed in chloroform, THF, and NMP containing LiBr, or in NMP stirred over P₂O₅ before use. Values of Mark-Houwink-Sakurada exponents for narrow distribution linear polystyrene indicate that pure NMP and NMP with 0.06 M LiBr are good solvents for polystyrene standards at 60°C. In contrast, SEC behavior of polyimides in pure NMP leads to splitting of the peaks with the major portion observed to pass through the columns at the exclusion limit. In contrast to strong polymeric chain expansion of the polyamic acid in dilute solution, presumably due to a polyelectrolyte effect, no increase of intrinsic viscosity of polyimide samples in pure NMP was observed. This exclusion effect of polyimides analyzed in NMP is discussed in terms of possible ion-exclusion from pores of the stationary phase. Differences in polystyrene calibration in NMP with or without additives and the temperature dependence of calibration curves in these mobile phases is discussed as well. ©1995 John Wiley & Sons, Inc.     

Size exclusion chromatography and viscometry in paper degradation studies. New Mark-Houwink coefficients for cellulose in cupri-ethylenediamine

The paper deals with the application of size exclusion chromatography (SEC) for the studies of paper degradation phenomena. The goal is to solve some of the technical problems connected with the calibration of multi-detector SEC system and to find the correlation between SEC and viscometric results of degree of polymerization of cellulose. The results gathered for the paper samples degraded by acidic air pollutant (NO₂) are used as an example of SEC–MALLS application. From the correlation between intrinsic viscosities and absolute value of molecular masses obtained with SEC/MALLS (Multi Angle Laser Light Scattering) technique, Mark-Houwink coefficients for cellulose in cupri-ethylenediamine solution were determined. Thus obtained coefficients were used for the determination of viscometric degree of polymerization (molecular mass) of the aged samples. An excellent correlation was found between the chromatographic values of molecular masses obtained with SEC–UV/VIS detection and the viscometric ones utilizing the improved values of Mark-Houwink coefficients.     

Rapid determination of molecular parameters of synthetic polymers by precipitation/redissolution high‐performance liquid chromatography using “molded” monolithic column

Rapid high‐performance liquid chromatography (HPLC) of polystyrenes, poly(methyl methacrylates), poly(vinyl acetates), and polybutadienes using a monolithic 50 × 4.6 mm i.d. poly(styrene‐co‐divinylbenzene) column have been carried out. The separation process involves precipitation of the macromolecules on the macroporous monolithic column followed by progressive elution utilizing a gradient of the mobile phase. Depending on the character of the separated polymer, solvent gradients were composed of a poor solvent such as water, methanol, or hexane and increasing amounts of a good solvent such as THF or dichloromethane. Monolithic columns are ideally suited for this technique because convection through the large pores of the monolith enhances the mass transport of large polymer molecules and accelerates the separation process. Separation conditions including the selection of a specific pair of solvent and precipitant, flow rate, and gradient steepness were optimized for the rapid HPLC separations of various polymers that differed broadly in their molecular weights. Excellent separations were obtained demonstrating that the precipitation‐redissolution technique is a suitable alternative to size‐exclusion chromatography (SEC). The molecular weight parameters calculated from the HPLC data match well those obtained by SEC. However, compared to SEC, the determination of molecular parameters using gradient elution could be achieved at comparable flow rates in a much shorter period of time, typically in about 1 min. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2767–2778, 2000     

Aqueous sec analysis of cationic polymers as gene carriers

Cationic polymers have been receiving much attention as non-viral gene vectors.The aqueous mobile phase was optimized in combination with Shodex OHpak SB columns for size-exclusion chromatography(SEC)analysis of disulfide-containing poly(ethylene imine)(PEI)derivatives used in gene delivery.Addition of acetonitrile in mobile phase was shown to be able to suppress the hydrophobic interactions between polymer analytes and the stationary phase.The absolute molecular weights and distributions of the cationic polymers were determined directly from online SEC-MALS(multi-angle light scattering)/RI(refractive index detector).The results demonstrate that a good SEC separation of disulfide-containing PEI derivatives used in gene delivery with little band broadening was achieved.     

测定木素磺酸盐和磺化碱木素相对分子质量分布的凝胶色谱法

用水溶性流动相在Ultrahydrogel柱上测定了木素磺酸盐和磺化碱木素的相对分子质量及其分布。流动相的离子强度和 pH值对样品和标样的保留时间和峰面积都有显著的影响。根据色谱峰的位置、峰面积和样品的分离程度 ,确定以 pH=7.0的0.1mol/LNaNO3 溶液为适宜的流动相。     

Recent progress in carbohydrate separation by high-performance liquid chromatography based on size exclusion

Since the introduction of stationary phases based on microparticulate porous silica and polymeric sorbents, rigid and semi-rigid, size-exclusion chromatography (SEC) has become established as a form of high-performance liquid chromatography. In recent years, there have beeen revolutionary developments in detection systems for high-performance SEC, which have placed the use of the method for the determination of molecular-size and molecular-weight distributions of polymers on a sound theoretical basis andincreased the range of information on molecular characteristics that can be retrieved from SEC data. This review surveys these changes in SEC systems and their application to the separation and molecular-weight distribution analysis of carbohydrates.