形状记忆聚(乳酸-乙醇酸)(PLLGA)的制备及性能研究

采用开环聚合法合成了一系列具有不同组成的聚(乳酸-乙醇酸)(PLLGA)共聚物, 并通过红外光谱(FT-IR)、核磁共振氢谱(¹H NMR)、凝胶渗透色谱(GPC)、差示扫描量热分析(DSC)、X射线衍射分析(XRD)和拉伸试验, 对PLLGA共聚物的化学结构、相结构、热性能、力学性能和形状记忆性能进行了系统研究, 并分析了其形状记忆效应的微观机理. 研究表明, 通过调整PLLGA共聚物的组成, 可获得良好的力学性能和形状记忆效应. 对PLLGA90/10和80/20, 由结晶部分及大分子链之间的缠结点共同作为固定相, 无定型部分作为可逆相. 而对PLLGA70/30和60/40, 仅由大分子链之间的缠结点作为固定相, 其无定型部分均作为可逆相. 综合而言, PLLGA80/20具有最好的形状记忆效应.     

聚乳酸基可降解形状记忆聚合物的制备、结构与性能

以三枝化低不饱和度聚环氧丙烷/聚乳酸两嵌段共聚物(POLA)为原料, 甲苯二异氰酸酯(TDI)交联制备可降解聚环氧丙烷/聚乳酸基聚氨酯(POLA-PU). 通过对POLA共聚物序列结构的调控, 制备了由高模量低断裂伸长率的脆性到低模量高断裂伸长率的韧性POLA-PU可降解形状记忆材料. 由TMA测得POLA-PU的形变温度为96～153 ℃. POLA-PU试样在140 ℃的形状记忆恢复时间不超过20 s. 在200%拉伸形变条件下, POLA-PU的形变固定率在65%～100%之间, 形变回复率均可达100%. 实验表明, 形状记忆行为取决于链的交联密度, 记忆效应归属于不同温度下柔性链的构象熵变化. 降解实验结果表明, 聚乳酸链段的引入赋予了该形状记忆材料良好的降解性能, 且随着聚乳酸含量的降低而下降.     

Fabrication of Transparent,Tough, and Conductive Shape‐Memory Polyurethane Films by Incorporating a Small Amount of High‐Quality Graphene

We report a mechanically strong, electrically and thermally conductive, and optically transparent shape‐memory polyurethane composite which was fabricated by introducing a small amount (0.1 wt%) of high‐quality graphene as a filler. Geometrically large (≈4.6 μm²), but highly crystallized few‐layer graphenes, verified by Raman spectroscopy and transmission electron microscopy, were prepared by the sonication of expandable graphite in an organic solvent. Oxygen‐ containing functional groups at the edge plane of graphene were crucial for an effective stress transfer from the graphene to polyurethane. Homogeneously dispersed few‐layered graphene enabled polyurethane to have a high shape recovery force of 1.8 MPa cm⁻³. Graphene, which is intrinsically stretchable up to 10%, will enable high‐performance composites to be fabricated at relatively low cost and we thus envisage that such composites may replace carbon nanotubes for various applications in the near future.     

形状记忆聚偏氟乙烯/丙烯酸酯/碳纳米管纳米复合材料的导电及导热性能

利用聚偏氟乙烯（PVDF）微小结晶的物理交联点作用,制备了形状记忆性能优异的聚偏氟乙烯/丙烯酸酯聚合物（PVDF/ACM）共混材料,为提高其导电及导热性能,于其中引入了碳纳米管（CNT）,系统研究了PVDF/ACM/CNT三元体系纳米复合材料的导热及导电性能。 结果表明,碳纳米管在PVDF/ACM体系中分散均匀;在基本保持其形状记忆性能的前提下,碳纳米管的加入使材料导热性能及导电性能有较大程度的提高：质量分数为4%的CNT使材料25 ℃的电阻值降低至5000 Ω/square,导热系数提高至0.157 W/(m·K)。     

Inverse Vulcanized Polymers with Shape Memory,Enhanced Mechanical Properties,and Vitrimer Behavior

The invention of inverse vulcanization provides great opportunities for generating functional polymers directly from elemental sulfur, an industrial by-product. However, unsatisfactory mechanical properties have limited the scope for wider applications of these exciting materials. Here, we report an effective synthesis method that significantly improves mechanical properties of sulfur-polymers and allows control of performance. A linear pre-polymer containing hydroxyl functional group was produced, which could be stored at room temperature for long periods of time. This pre-polymer was then further crosslinked by difunctional isocyanate secondary crosslinker. By adjusting the molar ratio of crosslinking functional groups, the tensile strength was controlled, ranging from 0.14±0.01 MPa to 20.17±2.18 MPa, and strain was varied from 11.85±0.88 % to 51.20±5.75 %. Control of hardness, flexibility, solubility and function of the material were also demonstrated. We were able to produce materials with suitable combination of flexibility and strength, with excellent shape memory function. Combined with the unique dynamic property of S−S bonds, these polymer networks have an attractive, vitrimer-like ability for being reshaped and recycled, despite their crosslinked structures. This new synthesis method could open the door for wider applications of sustainable sulfur-polymers.     

Inverse Vulcanized Polymers with Shape Memory,Enhanced Mechanical Properties,and Vitrimer Behavior

The invention of inverse vulcanization provides great opportunities for generating functional polymers directly from elemental sulfur, an industrial by‐product. However, unsatisfactory mechanical properties have limited the scope for wider applications of these exciting materials. Here, we report an effective synthesis method that significantly improves mechanical properties of sulfur‐polymers and allows control of performance. A linear pre‐polymer containing hydroxyl functional group was produced, which could be stored at room temperature for long periods of time. This pre‐polymer was then further crosslinked by difunctional isocyanate secondary crosslinker. By adjusting the molar ratio of crosslinking functional groups, the tensile strength was controlled, ranging from 0.14±0.01 MPa to 20.17±2.18 MPa, and strain was varied from 11.85±0.88 % to 51.20±5.75 %. Control of hardness, flexibility, solubility and function of the material were also demonstrated. We were able to produce materials with suitable combination of flexibility and strength, with excellent shape memory function. Combined with the unique dynamic property of S?S bonds, these polymer networks have an attractive, vitrimer‐like ability for being reshaped and recycled, despite their crosslinked structures. This new synthesis method could open the door for wider applications of sustainable sulfur‐polymers.     

聚氨酯弹性体力学性能影响因素探讨

研究了合成方法、原料的种类与配比、硫化工艺条件等因素对聚氨酯弹性体力学性能的影响。结果表明,聚氨酯弹性体的结构与组成以及由此引起的微相分离程度的变化是影响弹性体性能的重要因素。对于同样的聚合多元醇、二异氰酸酯及扩链剂合成的弹性体,采用不同的硫化及熟化条件其力学性能不同,并找到达到最佳力学性能所需的工艺条件。     

单组分聚氨酯清漆的制备与性能研究

不同的聚碳酸酯二元醇、聚四亚甲基醚二醇(PTMG)与二苯甲烷二异氰酸酯(MDI)、小分子二元醇反应,制得聚醚、聚碳酸酯型聚氨酯清漆。通过红外光谱分析结合其机械力学性能、耐水性等的测试结果,探讨聚碳酸酯型聚氨酯清漆的结构对形态和性能的影响。结果表明：随着硬段含量的增加,树脂涂膜的微相分离程度增加,机械性能提高;组分摩尔比例相同时,软段分子量的降低有利于提高树脂的软硬段相容性,增加树脂涂膜的物理机械性能;组分摩尔比例相同时聚酯型聚氨酯树脂的微相分离程度低于聚醚型聚氨酯树脂;MDI基溶剂型聚氨酯树脂的物理机械性能较好。     

叔胺型水性聚氨酯的合成及其性能

将含有不同胺基的聚氨酯预聚体在酸性水溶液中乳化得到水性聚氨酯．结果表明，胺基摩尔量相同时，由二甲基乙醇胺制得的水性聚氨酯粒径最小（０．４～２μｍ），甲基二乙醇胺制得的预聚体乳化后乳胶粒较粗（２～１５μｍ），而由三乙醇胺制得的预聚体根本得不到聚氨酯乳液．提出胺基的运动自由度是影响乳化能力的关键．二甲基乙醇胺制得的水性聚氨酯具有贮藏稳定性好、耐水性好，并呈现假塑性流体的特点．随着二甲基乙醇胺用量的增加，水性聚氨酯涂膜的断裂强度由１．０ＭＰａ增加到４．８ＭＰａ，动态粘弹谱的内耗峰变宽．     

不同异氰酸酯固化的蓖麻油／酚氧树脂聚氨酯的力学性能

以ＢＦ３·ＯＥｔ２为催化剂，４，４－二羟基二苯基丙烷与环氧氯丙烷反应，生成端羟基的酚氧树脂（Ａ），Ａ与蓖麻油（Ｂ）混合，用３种异氰酸酯（ＴＤＩ、ＩＰＤＩ和ＨＤＩ）作为固化剂，制得交联聚氨酯。研究了这３种聚氨酯的力学性能及形态与组成和二异氰酸酯结构的关系；改变ＮＣＯ／ＯＨ摩尔比及Ｂ与Ａ的质量比，可以制得具有较好力学性能的聚氨酯材料。蓖麻油，酚氧树脂，聚氨酯，力学性能     

Shape Memory Properties and Enzymatic Degradability of Poly(ε‐caprolactone)‐Based Polyurethane Urea Containing Phenylalanine‐Derived Chain Extender

Biodegradable shape memory polymers are promising biomaterials for minimally invasive surgical procedures. Herein, a series of linear biodegradable shape memory poly(ε‐caprolactone) (PCL)‐based polyurethane ureas (PUUs) containing a novel phenylalanine‐derived chain extender is synthesized. The phenylalanine‐derived chain extender, phenylalanine‐hexamethylenediamine‐phenylalanine (PHP), contains two chymotrypsin cleaving sites to enhance the enzymatic degradation of PUUs. The degradation rate, the crystallinity, and mechanical properties of PUUs are tailored by the content of PHP. Meanwhile, semicrystalline PCL is not only hydrolytically degradable but also vital for shape memory. Good shape memory ability under body temperature is achieved for PUUs due to the strong interactions in hard segments for permanent crosslinking and the crystallization‐melt transition of PCL to switch temporary shape. The PUUs would have a great potential in application as implanting stent.     

复合稀土对Fe-Mn-Si-Ni-C合金形状记忆效应的影响

通过弯曲法测量、热循环训练、扫描电镜、X射线衍射等方法，研究了复合稀土对Fe-Mn-Si-Ni-C合金形状记忆效应的影响。研究结果表明，Fe-Mn-Si-Ni-C合金中加入复合稀土，能够明显细化合金的金相组织，显著提高合金的形状记忆效应，并使合金表现出微弱的双程记忆效应。试验结果还表明，第一种训练途径以及加入微量复合稀土是降低应力诱发ε马氏体稳定化行之有效的方法，X射线衍射结果表明，该训练方法有助于提高合金中ε→γ转变的ε逆转变率，对提高合金的记忆性能起积极的作用。     

聚硅氧烷与纳米SiO_2复合改性光固化水性聚氨酯的制备与性能

以聚碳酸酯二元醇(PCD)和羟基封端的聚二甲基硅氧烷(PDMS)为软段、异佛尔酮二异氰酸酯(IPDI)为硬段,在乳化过程中引入纳米SiO_2,制得光固化水性聚氨酯纳米复合乳液。采用纳米粒度仪、SEM、光学接触角测量仪、电子拉力机等对复合乳液和复合膜的结构与性能进行了表征。研究结果表明:纳米SiO_2相互接触,形成了连续的纳米SiO_2网状结构贯穿于整个聚合物基体中;PDMS与纳米SiO_2的复合引入使复合膜杨氏模量、拉伸强度、断裂伸长率、表面疏水性及耐水性均得到显著提高。     

Synthesis and Characterization of Novel Liquid Crystalline Epoxides with Lateral Substituent Showing Imposing Shape Memory Properties

In this work, a series of novel shape memory liquid crystalline (LC) epoxides with lateral substituent were prepared and characterized. Dynamic mechanical analysis (DMA) and shape memory testing were used to investigate on the thermo-mechanical properties and shape memory effects of prepared samples. The results showed that the modulus in the rubbery region (E_R ) decreased as the length of lateral alkyl group increases. And more than 95% of the deformation can be fixed as the sample was cooled down below the glass transition temperature (T_g), which was determined by differential scanning calorimetry (DSC) measurement, and can be recovered completely as heating. Effects of the curing agent and substituent on the shape memory behavior were also studied. We found that LC epoxides cured by aromatic diamine have a higher recovery speed. The recovering speeds of the shape memory decreased as the length of lateral alkyl group inscreased. The local ordered structures and the lateral substituent played an important role in shape memory effects.     

Monocomponent Waterborne Polyurethane Adhesives: Influence of the Crosslinking Agent on Their Properties

To improve the properties of the monocomponent waterborne polyurethane (WPU) adhesives, a series of crosslinked WPU were prepared with trifunctional polyester polyol (P210) as crosslinking agent. The crosslinked WPU dispersions and their films were characterized by conventional methods. The adhesion property of the samples was measured from T-peel test of leather/WPU adhesive/leather joints. Compared with the linear one, the crosslinked WPU exhibited low viscosity, small particle size, and low surface tension. For crosslinked films, the thermal stability, water resistance and mechanical properties were remarkably enhanced. The experimental data of T-peel test indicated that the adhesive strength significantly increased to 4.8 KN/m by crosslinking up to the optimum crosslink index of 1.2 and then showed a small decrease with excess.     

Thermosetting Shape Memory Polymers and Composites Based on Polybenzoxazine Blends,Alloys and Copolymers

When dealing with smart polymers, in particular with shape memory polymers, the polymer type and composition specify the overall material properties and in particular the extent of the shape memory effect. Polybenzoxazines as a polymer with high potential for structural applications represent a promising component for materials with both shape memory effect and structurally interesting material properties. This minireview gives insight into how the shape memory effect, in particular the shape recovery event, is influenced by internal factors such as polymer structure, morphology and external factors such as filler addition.     

Bio‐based hyperbranched polyurethane/Fe3O4 nanocomposites as shape memory materials

The bio‐based shape memory polymers have generated immense interest as advanced smart materials. Mesua ferrea L. seed oil‐based hyperbranched polyurethane (HBPU)/Fe₃O₄ nanocomposites were prepared by the in‐situ polymerization technique. The transmission electron microscopy confirmed the homogeneous distribution of the Fe₃O₄ nanoparticles in polymer matrix, whereas Fourier transform infrared spectroscopic study revealed the presence of strong interfacial interactions between them. The incorporation of Fe₃O₄ (0 to 10 wt%) into the HBPU resulted in an increase in tensile strength (5.5–15 MPa) and scratch resistance (3–6 kg). The thermo‐gravimetric analysis indicated the improvement of thermal stability (240–270°C) of the nanocomposites. The nanocomposites exhibited full shape fixity, as well as almost full shape recovery under the microwave stimulus. The shape recovery speed increased with the increase of Fe₃O₄ nanoparticles content in the nanocomposites. Thus, the studied nanocomposites might be used as advanced shape memory materials in different potential fields. Copyright © 2013 John Wiley & Sons, Ltd.     

New Millable Polyurethane/Organoclay Nanocomposite: Preparation,Characterization and Properties

The preparation, characterization and properties of novel millable polyurethane/organoclay nanocomposites are reported. Clay treated with methyl tallow bis(2‐hydroxyethyl) quaternary ammonium chloride was used as an organoclay for nanocomposite preparation. X‐ray diffraction indicated the intercalation of polymer chains inside the interlayer spacings of the clay. Dynamic mechanical analysis showed a significant increase in storage modulus, and tensile strength increases with increased organoclay loading.

X‐ray diffraction patterns of millable polyurethane/organoclay nanocomposites.