Direct determination of bismuth(III) in sea water by square-wave anodic stripping voltammetry at a glassy-carbon rotating-disk electrode

A method for the determination of bismuth(III) in untreated sea water at its natural pH of 8.1 is described. A bare glassy-carbon rotating-disk electrode is preconditioned by placing in the sample at an applied potential of ?0.8 V vs. Ag/AgCl for 20 min; after stripping to ?0.4 V, bismuth is accumulated for 5 min at ?0.8 V and finally stripped in the square-wave mode. The bismuth peak appears at ca. + 0.10 V vs. Ag/AgCl; peak height is linearly related to concentration up to 2×10^?10 mol dm^?3. The method is highly selective for bismuth. The concentration of Bi(III) in the investigated sample was (6±1)×10^?11 mol dm^?3, or 12±2 ng dm^?3. The different types of response obtained are discussed.     

Direct determination of selenium in whole blood by anodic stripping voltammetry

Trace quantities of selenium can be determined in the presence of iron, copper and lead using anodic stripping voltammetry, depositing at –0.60 V in 0.1M HClO₄ and stripping in the anodic direction. Two separate peaks are observed at –0.25 V and –0.10 V belonging to copper and selenium, respectively. Sometimes one peak may be observed for both copper and selenium. In this case one more stripping (without deposition) must be done to obtain separate peaks. After standard addition, two strippings have to be done also. With this proposed method, 10^–7 M selenium could be determined as (1.09±0.03) × 10^–7 M with a 90% confidence interval in blood samples without any separation.Presented at Xth National Chemistry Congress, Bursa, Turkey, September 19–21, 1994     

Quantitative determination of zinc in milkvetch by anodic stripping voltammetry with bismuth film electrodes

Bismuth film electrode (BiFE) was shown to be an attractive alternative to common mercury film electrode (MFE) for anodic stripping voltammetric measurements. In this study, bismuth film, that was in situ deposited onto glassy carbon electrode, was used to detect zinc content of milkvetch, used in traditional Chinese medicine. Variables affecting the response have been evaluated and optimized. Experimental results showed a high response, with a good linearity (between 0.5 × 10⁻⁶ mol L⁻¹ and 3 × 10⁻⁶ mol L⁻¹) a good precision (R.S.D. = 3.58%) and a low detection limit (9.6 × 10⁻⁹ mol L⁻¹ with a 120 s anodic). The anodic stripping performance makes the bismuth film electrode very desirable for measurements of trace nutritive element zinc in milkvetch and should impart possible restrictions on the use of mercury electrode.     

The determination of copper,lead and cadmium in sea water by differential pulse anodic stripping voltammetry

The effect of various instrumental parameters is investigated and optimized conditions established. The results are in accordance with the theory of differential pulse anodic stripping voltammetry. Both a hanging mercury drop electrode, and a rotating glassy carbon electrode mercury plated in situ were used. The best detection limit is obtained with the mercury film electrode, but the hanging mercury drop electrode is more reproducible. The differential pulse stripping technique is compared to linear sweep stripping, and increased sensitivity and better peak separation is demonstrated for the former technique, particularly when a hanging mercury drop electrode is used. However, the differential pulse technique will also improve the detection limit for a mercury film electrode, if the electrode has a non-ideal response with a corresponding high background current.     

Determination of traces of bismuth in copper by anodic stripping voltammetry

Summary Procedures are described for the determination of bismuth impurities in. copper using anodic stripping voltammetry on a hanging mercury drop electrode. Bismuth was previously separated from copper by cation or anion exchange in hydrochloric acid. The method was applied to the analysis of commercially available high purity copper, showing satisfactory sensitivity and accuracy. The detection limit was about 2×10^–9 M bismuth in solution for a pre-electrolysis time of 15 min (–0.5 V vs. Ag/AgCl); this corresponds to 0.004 ppm of bismuth for a 1 g sample and a final volume of 10 ml after separation.

---

Bestimmung von Wismutspuren in Kupfer durch anodische Amalgamvoltammetrie

Zusammenfassung Mit hängendem Quecksilbertropfen. Wismut wird vor der Bestimmung durch Kationen oder Anionenaustausch aus salzsaurer Lösung vom Kupfer abgetrennt. Das Verfahren wurde zur Analyse von handelsüblichem hochreinem Kupfer angewendet. Mit einer Vorelektrolysedauer von 15 min (–0,5 V gegen Ag/AgCl) konnten noch 2×10^–9 M Bi bestimmt werden; das entspricht 0,004 ppm Bi für eine 1 g-Probe bei einem Endvolumen von 10 ml nach der Trennung.

     

Determination of copper by anodic stripping voltammetry: anomalous behavior in sea water

Repeated cycles of plating and stripping using a mercury-coated graphite electrode in raw sea water show increasing negative errors for copper while lead and cadmium are unaffected. This phenomenon, which is not observed in acidified sea water, is attributed to formation of electroinactive Cu(I) species on the electrode.     

The determination of gold by anodic stripping voltammetry

A method is described for the routine determination of gold as its chloride or cyanide complex by anodic stripping voltammetry at a glassy carbon electrode coupled to a microprocessor-controlled voltammeter. The preferred supporting electrolyte is 0.1 M HCl/0.32 M HNO₃, with plating at ?200 mV or ?1200 mV (vs. Ag/AgCl). The stripping peak potentials range from 830 to 1150 mV (vs. Ag/AgCl) depending on concentration and plating time. Precision (percent relative standard deviation) is better than 5 % for a range of concentrations between 5 μg l^?1 and 1000 μg l^?1. The detection limit is about 5 μg l^?1 for a 5-min plating period. Interferences from Cu, Hg, Ag and other electroactive species are overcome by preliminary extraction with diethyl ether.     

Trace-metal determination by second-harmonic alternating-current anodic stripping voltammetry

Second-harmonic alternating-current voltammetry can be used for the sequential determination of two electroactive species having very similar half-wave potentials (deltaE(1 2 ) < 50 mV). Since the concentrations of such metals in samples of special interest are often at trace levels, for their determination second-harmonic a.c. voltammetry (extremely selective but not sufficiently sensitive) can usefully be combined with the anodic stripping method, which has a very high analytical sensitivity. The determination of tin and lead as well as of indium and cadmium in 1M hydrochloric acid is described. The half-wave potentials are only 35 and 45 mV apart, respectively, for these systems. A three-electrode cell was used with a long-lasting sessile-drop mercury electrode as the working electrode, with a drop-time of 240-300 sec. The detection limit was found to be 10(-8)M for all four elements studied. The precision expressed as the relative standard deviation was 2-3% and the relative error was 1-2%.     

Determination of traces of antimony and tin in copper by anodic stripping voltammetry

The determination of antimony and tin impurities in copper by anodic stripping voltammetry on a hanging mercury drop electrode is described. Antimony and tin were previously separated from copper by distillation with hydrobromic acid or a mixture of hydrobromic acid and hydrochloric acid. The method was applied to the analysis of various high-purity copper samples, commercially available, showing satisfactory sensitivity and precision. The determination limit was about 1.4· 10^-9M for antimony and 7·10^-10M for tin in solution, for pre-electrolysis times of respectively 15 and 25 min; this corresponds to 0.8 p.p.b. of antimony and 0.3 p.p.b. of tin for a 2-g sample and a final volume of 10 ml after separation.     

The determination of platinum in sea water by adsorptive cathodic stripping voltammetry

The catalytic effect of the formazone complex with platinum on the development of hydrogen at a mercury electrode is used to provide a very sensitive method of determining dissolved platinum in fresh and sea water by adsorptive cathodic stripping voltammetry. The optimal analytical conditions include the addition of 0.012% (w/v) formaldehyde, 0.0015% (w/v) hydrazine and 0.5 M sulphuric acid to the sea water. The complex is adsorbed for 1–20 min at ?0.925 V on the hanging mercury drop electrode, followed by a differential-pulse scan in a negative direction. The hydrogen reduction peak catalysed by the platinum complex appears at ?1.045 V. The limit of detection is 0.04 pM Pt with an adsorption time of 10 min, which is quite sufficient to determine dissolved platinum in sea water. The interference of surface-active compounds is eliminated by ultraviolet irradiation of the acidified sample. The method is applied to several sea-water samples. Comparative experiments showed that stripping chronopotentiometry is not sufficiently sensitive to determine platinum in sea water without preconcentration.     

Simultaneous determination of mercury and arsenic by anodic stripping voltammetry

An electrochemical method for the simultaneous determinations of Hg^II concentration and total As^III and As^V concentration has been developed. The method does not require the additional preliminary step of the chemical reduction of As^V to As^III, or oxidation of As^III to As^V before stripping analysis takes place. Also, the method for the simultaneous determination of Hg^II concentration and As^III concentration is described. Measurements were performed in 0.1 M HCl using a gold-plated graphite electrode as sensor. Detection limits for both methods are below 0.4 ppb. Relative standard deviation did not exceed 15%. The possible interference by other trace metals was investigated. Analyses of natural water and industrial solutions were made using proposed methods and AAS. The t-test demonstrates that there was no significant difference between the results obtained with these methods. Proposed methods decrease the time of analysis because concentrations of the Hg^II and arsenic ions were measured simultaneously. Also, the removal of the additional step of chemical reduction of As^V to As^III or oxidation of As^III to As^V decreases analysis time, and also reduces the chance of contamination due to the use of additional reagents.     

The determination of silver in ores by anodic stripping voltammetry

Stripping voltammetry at a rotating glassy carbon electrode is proposed for the determination of silver in ores. The ores or concentrates are dissolved in suitable acid mixtures, and silver is separated either by extraction with dithizone in carbon tetrachloride, or by adsorption on silica from ammoniacal buffered solution and subsequent elution with 0.1 M nitric acid. The results obtained with stationary and rotating glassy carbon electrodes are discussed. Stripping voltammetry and fire assay give results in reasonably good agreement.     

复合铋膜电极阳极溶出法测定水样中的痕量铟

在玻碳电极上采用电化学沉积法制备了新型铕离子掺杂普鲁士蓝复合铋膜电极,建立了用示差脉冲阳极溶出法测定环境水样中痕量铟的分析方法。讨论了铟在常规铋膜电极和复合铋膜电极上的溶出性能,对铋膜的厚度、支持电解质、测定底液的pH、富集时间和富集电位等参数进行了优化。在最佳实验条件下,铟的阳极溶出峰电流与其浓度在2~20μg/L和20~100μg/L范围内分别呈良好的线性关系,检测下限为0.15μg/L(S/N=3),相对标准偏差RSD2.0%。该法用于实际水样中痕量铟的测定,样品回收率为97.5%~103%。     

Determination of lead and antimony in firearm discharge residues on hands by anodic stripping voltammetry

When a person fires a gun, trace quantities of lead, antimony and barium are deposited on the hand. Detection of high levels of these trace metals on the hand of a suspect may therefore be significant evidence in an investigation. In this study conditions for the determination of lead and antimony in gunshot residues by anodic stripping voltammetry using a mercury-coated graphite electrode are established. A sample is collected by washing the hand in 1M hydrochloric acid. Lead is determined in a portion of this sample, with 1M hydrochloric acid as electrolyte. Antimony is determined in a second portion, with 4M hydrochloric acid as electrolyte. Prior separation or preconcentration steps are not required for either analysis. The procedure has been applied to samples obtained from five "normal" hands and five hands after they have fired a weapon.     

Direct analysis of palladium in active pharmaceutical ingredients by anodic stripping voltammetry

Anodic stripping voltammetry, a classical electroanalytical method has been optimized to analyze trace Pd(II) in active pharmaceutical ingredient matrices. The electroanalytical approach with an unmodified glassy carbon electrode was performed in both aqueous and 95% DMSO/5% water (95/5 DMSO/H₂O) solutions, without pretreatment such as acid digestion or dry ashing to remove the organics. Limits of detection (LODs) in the presence of caffeine and ketoprofen were determined to be 11 and 9.6 μg g⁻¹, with a relative standard deviation (RSD) of 5.7% and 2.3%, respectively. This method is simple, highly reproducible, sensitive, and robust. The instrumentation has the potential to be portable and the obviation of sample pretreatment makes it an ideal approach for determining lost catalytic metals in pharmaceutical-related industries. Furthermore, the simultaneous detection of Pd(II) with Cd(II) and Pb(II) in the low μg L⁻¹ range indicates that this system is capable of simultaneous multi-analyte analysis in a variety of matrices.     

Direct determination of cadmium and lead in pharmaceutical ingredients using anodic stripping voltammetry in aqueous and DMSO/water solutions

A new electrochemical method has been developed to detect and quantify the elemental impurities, cadmium(II) (Cd²⁺) and lead(II) (Pb²⁺), either simultaneously or individually in pharmaceutical matrices. The electro-analytical approach, involving the use of anodic stripping voltammetry (ASV) on an unmodified glassy carbon electrode, was performed in both aqueous and in a 95/5 dimethyl sulfoxide (DMSO)/water solutions, without acid digestion or dry ashing to remove organic matrices. Limits of detection (LODs) in the μg L⁻¹ [or parts per billion (ppb), mass/volume] range were obtained for both heavy metals - in the presence and absence of representative pharmaceutical components. To the best of our knowledge, the work demonstrates the first analysis of heavy metals in DMSO/water solutions through ASV. The strong reproducibility and stability of the sensing platform, as well as obviation of sample pretreatment show the promise of utilizing ASV as a sensitive, robust, and inexpensive alternative to inductively-coupled-plasma (ICP)-based approaches for the analysis of elemental impurities in, e.g., pharmaceutical-related matrices.     

Nafion/2,2'-bipyridyl-modified bismuth film electrode for anodic stripping voltammetry

This paper describes the fabrication, characterisation and the application of a Nafion/2,2′-bipyridyl/bismuth composite film-coated glassy carbon electrode (NC(Bpy)BiFE) for the anodic stripping voltammetric determination of trace metal ions (Zn²⁺, Cd²⁺ and Pb²⁺). The NC(Bpy)BiFE electrode is prepared by first applying a 2.5 mm³ drop of a coating solution containing 0.5 wt% Nafion and 0.1% (w/v) 2,2′-bipyridil (Bpy) onto the surface of a glassy carbon electrode, while the Bi film was plated in situ simultaneously with the target metal ions at −1.4 V. The main advantage of the polymer coated bismuth film electrode is that the sensitivity of the stripping responses is increased considerably due to the incorporation of the neutral chelating agent of 2,2′-bipyridyl (Bpy) in the Nafion film, while the Nafion coating improved the mechanical stability of the bismuth film and its resistance to the interference of surfactants. The key experimental parameters relevant to both the electrode fabrication and the voltammetric measurement were optimized on the basis of the stripping signals. With a 2 min deposition time in the presence of oxygen, linear calibration curves were obtained in a wide concentration range (about 2-0.001 μM) with detection limits of 8.6 nM (0.56 μg dm⁻³) for Zn²⁺, 1.1 nM (0.12 μg dm⁻³) for Cd²⁺ and 0.37 nM (0.077 μg dm⁻³) for Pb²⁺. For nine successive preconcentration/determination/electrode renewal experiments the standard deviations were between 3 and 5% at 1.2 μM for zinc and 0.3-0.3 μM concentration level for lead and cadmium, respectively, and the method exhibited excellent selectivity in the presence of the excess of several potential interfering metal ions. The analytical utility of the stripping voltammetric method elaborated was tested in the assay of heavy metals in some real samples and the method was validated by ICP-MS technique.     

Selective method for the determination of gold by anodic stripping voltammetry

A highly selective method for the deter- mination of gold by anodic stripping voltammetry is described. For preconcentration a glassy carbon electrode, activated by deposition of small amounts of gold before the measurement, is proposed. The Au³⁺ reduction process at such an electrode is effective starting with the potential +0.4 V vs. Ag/AgCl electrode. A linear dependence of the current of the gold stripping peak on the gold concentration was obtained in the range from 5×10^–8 to 1×10^–6 mol/l. The relative standard deviation for 2×10^-7 mol/l HAuCl₄ was 4.2% (n=5). The detection limit was 4×10^-9 mol/l. The accuracy of the method was verified by the determination of gold in reference materials.     

Trace analysis by anodic stripping voltammetry

Summary An anodic stripping voltammetric method for the determination of zinc in silicates is described and discussed. The method is sensitive and is not affected by interferences resulting from varying sample composition.

---

Zusammenfassung Ein Verfahren zur Bestimmung von Zink in Silicaten mit Hilfe der anodischen Amalgamvoltammetrie wird beschrieben und diskutiert. Das Verfahren ist empfindlich und wird durch verschiedenartige Zusammensetzung der Probe nicht beeinflußt.

---

---

Dedicated to Prof. Dr. M. von Stackelberg on his 70th birthday.

---

This work was performed under the sponsorship of the U.S.National Bureau of Standards. Reproduction of this article, with the customary credit to the source, is permitted.